Search Documents

By Harold B. Goldman, Don Reining

The sand and gravel industry is the largest nonfuel mineral industry in the nation. In 1981, the production of sand and gravel totaled 755 million tons valued at $2.3 billion. California, which leads the nation with more than 110 million tons, together with Alaska, Texas, Michigan, and Ohio, account for 36% of the total production in the nation (Table 1). In commercial usage, sand applies to rock or mineral fragments ranging in size from particles retained on a No. 200 sieve (0.074 mm openings) to those passing a No. 4 sieve (4.76 mm openings). Gravel consists of rock or mineral fragments larger than 4.76 mm, ranging up to 88.9 mm (3 ½ -in.) maximum size. The construction industry consumes 97% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see the chapter on "Silica and Silicon"). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material which is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster. Portland Cement Concrete Aggregates Portland cement concrete consists of sand and gravel surrounded and held together by hardened portland cement paste. Concrete mixes commonly contain 15-20% water, 7-14% cement, and 66-78% aggregate. Sand and gravel used as concrete aggregate have to meet many requirements (Goldman, 1956). Premature deterioration of concrete has been traced in many instances to the use of unsuitable aggregates. Asphaltic Aggregate Asphaltic mixtures used predominantly for paving consist of combinations of sand, gravel, and mineral filler (material finer than 0.003 in.), uniformly coated and mixed with asphalt produced in the refining of petroleum. Except for the addition of mineral filler, sand and gravel used as asphaltic aggregate must meet the same general physical requirements as materials used for portland cement concrete aggregate. General Requirements of Aggregates Construction aggregate has many requirements that are difficult to meet if only unprocessed material from natural deposits is used. Suitable material is composed of clean, uncoated, properly shaped particles which are sound and durable. Soundness and durability are terms used to denote the ability of aggre- [ ]

Jan 1, 1983

By Dara P. Antia, Morris Cohen, Frank S. Gardner

THERE is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a specimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallographic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X-ray exposure and film-development conditions, a standard reference line is superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

FOLLOWING the presentation of the papers by Messrs. Mahan and Butler, the discussion printed below ensued. A. C. LANE* With particular reference to the New England con-sumer, I entirely agree with Mr. Mahan that intelli-gent marketing methods will do a good deal, but there is more than one way of improving them. For instance, coal can be shipped best to New England about this time of year-after the storms of the winter and before the movement of crops in the summer. For that reason there ought to be seasonal freight rates. This will be agreed to by most coal men if you will ask them, especially those who are connected with large concerns like the Metropolitan Coal Co., and yet they do not get seasonal freight rates partly because the railroads are afraid if they once reduce them they will never have a chance to get them back again. But it would be an improvement to have seasonal freight rates. Another thing: When we are buying in New England we want really a certain amount of heat value in our coal. There is no great advantage in our buying ash, nor is there any particular advantage in the railroad shipping ash and clogging the circulatory system of the body politic any more than clogging the circulatory system of the physical body. It would be desirable if the wholesaler, and to some extent the retailer, could guarantee the amount of ash or sell their coal on heating value. If you are interested in that you will find some interesting charts, in "Anthracite Coal Costs Analyzed," a pamphlet issued by the Anthracite Coal Consumers Association, Inc., New York City, as to rates from various and sundry points for bituminous and anthra-cite coal from the field to New York, Buffalo and Chi-cago. Here in New England they are both up against the competition of oil. About 3 or 3 1/2 bbl. oil will do the work of a ton of coal. One of my millionaire friends who is well posted on the situation is putting oil in his Commonwealth Avenue house because it is the most economical. Moreover, we can get Welsh coal from across the water (and help equalize this matter of exchange with Europe) in close competition with Penn-sylvania coal.

Jan 4, 1928

By Herbert H. Uhlig

A STUDY of passivity in chromium-iron alloys holds considerable interest, both because of the present-day practical importance of the stainless steels, and because of the scientific importance attached to the mechanism of their corrosion resistance. Upon the discovery of the passive chromium-iron alloys in 1912, it seemed logical to attribute the observed phenomenal corrosion resistance to a thin, continuous, protective reaction product on the surface. The product was thought to be Cr2O3 or a similar oxide containing both chromium and iron. This mechanism seemed likely in view of Michael Faraday's conjecture that passive iron is not reactive in concentrated nitric acid because of an oxide on the metal surface.† Since 1912, data have accumulated that permit a further exploration into the nature of passivity and provide a new approach to the problem. A summary of the facts lends considerable weight to a mechanism based not on physical protection of an oxide or similar compound, although such compounds may be present on the surface, but to a change in tendency of surface metal atoms to react chemically. This change in reaction tendency is ascribed to chemisorbed films that effectively satisfy residual valence forces of the metal surface, but do not appreciably disturb the positions of metal atoms in the lattice. In other words, formation of a new lattice such as that of an oxide is not a necessary condition for this type of passivity. The decreased reaction tendency of the metal by reason of chemisorbed films can thereby account for low reaction rates of the stainless steels in many media, as well as a noble galvanic potential as is observed. Substances capable of adsorbing on the stainless steels, and hence accompanying the property of passivity, are typically oxygen, nitrites or chromates, but are not in any sense limited to these. Other elements and compounds can also chemisorb, and therefore may also play a major part in the mechanism of passivity in specific media. The mechanism of passivity based on chemisorption or activated adsorption begins with the interpretation Langmuir proposed for his experiments concerning adsorbed oxygen on tungsten.1 He found that adsorbed oxygen was tightly bound, remaining on the tungsten surface above temperatures at which WO3 rapidly volatilizes. The oxygen in such a state did not readily react with hydrogen even at

Jan 1, 1947

By J. C. Motz

Introduction The variations in crushing plant design seen during the past 30 years provide a valuable source of information and experience from which one can select the optimum arrangement for a specific requirement. The purpose of this paper is to examine some specific equipment configurations as they relate to operating efficiency, plant availability and final product size in the form of mill feed. Due to the varied ore properties, physical space limitations, size of ore body and financial resources, there is no single crushing or grinding flowsheet that is best. Since energy costs have risen dramatically during the recent past, it became obvious that significant savings are possible by selecting equipment and a circuit which offers low power requirements balanced with low wear metal and installed equipment costs. Relatively clear and measurable are the metal and maintenance costs and the ever increasing cost of energy. Metal costs in the form of crusher liners have not quite doubled in the last 20 years, while power costs have increased by a factor of four or five, depending on the region considered. Estimates made only a few years ago on the increased cost of energy are obsolete in view of the recent unstable conditions. Since power is therefore becoming the largest cost area, it behooves us to investigate potential cost saving methods in the form of lowering the KWH/Ton of crude. Crushing To reduce run-of-mine to mill feed requires reduction in a series of stages. The physical size and power requirements of a crusher capable of reducing hard rock vary depending on the application. Extended experience in most crushing plants show that a minus 19MM (3/4 in.) rod mill feed can be and is being produced in three stages of crushing. In the majority of cases, the last crushing stage is closed circuited using anywhere from 19MM (3/4 in.) to 14MM (9/16 in.) slotted openings on the sizing deck. In some copper concentrators, the mill feed is all passing 13MM (1/2 in.) using three stages of crushing and 14MM (9/16 in.) square openings on the closed circuit screens. It was felt by some that crushing to this fine size is only possible if the ore is friable and is relatively soft in comparison to the harder ores. Our results show that some of the copper ores are as hard as taconite and are crush-

Jan 1, 1982

By W. H. Hough, P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1943 resulted in the discovery of 11 new fields as compared with 12 discovered in the same area during I942. Of the 11 new fields, eight are classed as oil and/or condensate and three as gas fields. In addition to the new discoveries, several more or less important new horizons and extensions were encountered in some of the older fields, as noted in the text under the heading "New Pays and Extensions.'' Drilling During the year, 418 wells were drilled, as compared with 356 drilled during 1942. Of these, 323 were field wells, of which 188 produced oil, 21 were gas wells and 114 were dry holes. The remaining 95 viere wildcats, 12 of which produced oil, 4 produced gas and 79 dry holes. Distribution of themwildcats with respect to the various trends may be summarized as follows: over the 91,340,492 bbl. produced in the same area during 1942. The production statistics in the text and the accompanying tables include condensate or distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties all of the drilling and production" data applicable to this particular area. Outstanding Fields of 1943 The Upper Texas Gulf Coast covered in this report has 178 more or less active oil and gas fields, including the 1943 discoveries. Of these Table 4 lists those that were most important from the standpoint of production. Each of these fields pro duced in excess of one million barrels of oil during 1943. Some of the interesting facts to be noted from this list of some 26 oil fields are: (I) four of the fields— namely, Conroe, Hastings, Friendswood and Thompson—each produced more than 10 million barrels during 1943, whcrcas Conroe and Hastings were the only fields that produced 10 million barrels during 1942; (2) some of the older fields (discovered prior to 1920), such as Barbers Hill, West Columbia, and Hull, are still producing in excess of one million barrels annually; (3) some of the fields more than doubled their 1942 production—e.g., Anahuac and Friendswood. The large increase in production in practically all instances is the result of increased allowables from wells drilled prior to 1943 and

Jan 1, 1944

By W. H. Hough, P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1943 resulted in the discovery of 11 new fields as compared with 12 discovered in the same area during I942. Of the 11 new fields, eight are classed as oil and/or condensate and three as gas fields. In addition to the new discoveries, several more or less important new horizons and extensions were encountered in some of the older fields, as noted in the text under the heading "New Pays and Extensions.'' Drilling During the year, 418 wells were drilled, as compared with 356 drilled during 1942. Of these, 323 were field wells, of which 188 produced oil, 21 were gas wells and 114 were dry holes. The remaining 95 viere wildcats, 12 of which produced oil, 4 produced gas and 79 dry holes. Distribution of themwildcats with respect to the various trends may be summarized as follows: over the 91,340,492 bbl. produced in the same area during 1942. The production statistics in the text and the accompanying tables include condensate or distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties all of the drilling and production" data applicable to this particular area. Outstanding Fields of 1943 The Upper Texas Gulf Coast covered in this report has 178 more or less active oil and gas fields, including the 1943 discoveries. Of these Table 4 lists those that were most important from the standpoint of production. Each of these fields pro duced in excess of one million barrels of oil during 1943. Some of the interesting facts to be noted from this list of some 26 oil fields are: (I) four of the fields— namely, Conroe, Hastings, Friendswood and Thompson—each produced more than 10 million barrels during 1943, whcrcas Conroe and Hastings were the only fields that produced 10 million barrels during 1942; (2) some of the older fields (discovered prior to 1920), such as Barbers Hill, West Columbia, and Hull, are still producing in excess of one million barrels annually; (3) some of the fields more than doubled their 1942 production—e.g., Anahuac and Friendswood. The large increase in production in practically all instances is the result of increased allowables from wells drilled prior to 1943 and

Jan 1, 1944

By R. J. Linney

Reserve Mining Co. produces 5 million tons of iron ore pellets per year. The finished product runs about 65.50 pct Fe, with 7.75 to 8.00 pct SiO2. Less than 12 pct arrives at the blast furnaces smaller than % in. This plant was originally designed to produce 3.75 tons annually—not 5 million. To handle the increased tonnage a fifth fine crushing line was added, and some very minor changes were made. When production can be stepped up 33 1/3 pct without extensive additions or changes—within the short period of a year—basic engineering has been sound. Operators of the plant consider it the best design job they have seen or heard of, and competent authorities have said that start-up was quicker and easier than for any previous large-scale minerals beneficiation plant. One big advantage is the elbow room allowed. Generally speaking, there is an eternal conflict between operator and designer over space. The designer has his costs per cubic foot, and he is keenly aware that if he permits the number of cubic feet to rise unnecessarily, total costs will be too high. But this was a new operation, and on a large scale. There were no proven standards to go by. Realizing this, Reserve's engineers provided ample and efficient access to machinery, allowing extra space for unanticipated situations. In three years of production this planning has paid off handsomely. Gravity Flow Saves Time and Money: This plant is on a rocky hillside, the car dumper about 270 ft above Lake Superior. In locating buildings and placing machinery the designers mad= good use of gravity flow, at considerable financial savings. In the concentrator building from rod mills to filters, gravity carries the material between all stages of the operation except one—the closed circuit pumping of concentrate between cone classifiers and ball mills. Since no machine is located directly above any other, an observer can stand on the truck ramp adjacent to the offices and laboratory and see practically every phase of activity in the huge building. The first mill section started in August 1955. After a day's run several modifications were made on auxiliary chutes and launders where spillage had occurred. This procedure was followed for the first

Jan 1, 1960

By Carl Tolman, LeRoy Scharon, Harold Powers

THIS paper presents geophysical and subsurface data observed in the vicinity of Shafts No. 1 and and 5 of the National Lead Co. lead mines at Fred-ericktown, Madison County, Missouri, see Fig. 1. The area selected is an excellent example to illustrate the close correlation between geophysical data and geological facts as revealed by drilling and mining. Such close correlations make geophysical applications appropriate to the development of known ore-bodies as well as the exploration for new orebodies. In the past, magnetic and shallow electrical resistivity observations were made over limited areas in the Fredericktown lead district by the Missouri Geological Survey, with favorable results. The first extensive magnetic and electrical resistivity surveys were started by the U. S. Bureau of Mines in May 1945 in two areas located northwest and southwest of Fredericktown, as shown in Fig. 1. The results of these surveys were reported in April 1948 at Denver, spontaneous-polarization surveys were made over the property of the St. Louis Smelting and Refining Co. at Fredericktown by Sherwin F. Kelly Geophysical Services, Inc. Aeromagnetic surveys were completed in 1948 over the Fredericktown quadrangle by the U. S. Geological Survey. Since 1945 geophysical surveys have been an important part of exploration programs in the Fred- ericktown district. Such methods, magnetic and electrical resistivity, are now serving as guides in the further development of known orebodies. On an irregular pre-Cambrian igneous erosion surface Lamotte sandstone of upper Cambrian age was deposited, partially filling the topographic basins, see Fig. 2. Above and conformable with the Lamotte sandstone lies the Bonneterre formation, a dolomite with locally interbedded thin dolomitic limestones and shales at its base. This formation also only partially filled the topographic basins. The Bonneterre was overlain by the Davis, Derby, Doe Run, and Potosi formations, which are principally dolomite. Uplift, tilt, and slight warping has allowed erosion and weathering to remove most of the sediments overlying the Bonneterre, and in many places, not far from the mine, the Lamotte sandstone is exposed. This erosion has also exposed areas of pre-Cambrian igneous rock. The Lamotte sandstone, having been deposited on an irregular pre-Cambrian surface, is extremely variable in thickness and ranges from zero where it laps the pre-Cambrian rocks to 250 ft thick in the deeper basins. In the vicinity of the mines the Bonneterre dolomite ranges from zero where it wedges out against the pre-Cambrian igneous rocks to 400 ft thick. The ore deposits occur as a bedded disseminated type1 and are chiefly composed of galena and pyrite with minor amounts of chalcopyrite and siegenite. Heavy pyrite and marcasite mineralization may be found throughout the Bonneterre formation. However, there is little or no apparent association of these iron sulphide bodies lying above the ore hori-

Jan 1, 1954

By E. A. Hopkin

Laboratory tests conducted by the author. together with actual field experience in Canada. have indicated the magnitudc of some of the factors affecting ability of drilling mud to clean the hole. A correlation was observed between funnel viscosity and particle slip velocity. A relationship was also observed between the Bingham yield value of the mud and the particle .slip velocity. Laburatury tests indicated little change in slip velocity with funnel viscosities up to ahout 80 sec/qt or to yield values of aboul 15 lb/100 .sq ft. The lip velocity of the partic1e.s. studied vuried from 160 ft/min with water to neerly zero for high mud viscositie. lncreasing the mud density, creating laminar annular mud flow or rotating the drill pipe Mlay also improve the carrying capacity of mud. Field tests indicated that during fast upper-hole drilling, the rate of cutting removal must he sufficien to maintain the concentration of cuttings in the annulus at less than 5 percent by volume to prevernt balled-up drill collars and .stuck drill pipe. INTRODUCTION In the Mid-Continent area, hole cleaning during rotary drilling normally involves the use of low-density drilling muds with funnel viscosities varying from 26 to 80 sec/qt. However, frequently it is necessary to raise the mud viscosity in excess of 200 sec/qt to clean the hole. In addition, field experience has indicated that during very fast upper-hole drilling, annular mud velocities considerably in excess of the maximum slip velocity of the cuttings (normally considered to be 120 to 150 ft/min) are necessary to prevent balling the bit and drill collars. In view of these variations in mud properties and circulation rates necessary to clean the wellbore, a study of factors affecting hole cleaning and the relative magnitude of each was undertaken. The study was also prompted by the knowledge that a drilling mud with properties close to those of water would drill at rates several times that of a viscous mud. The carrying capacity of these near-water muds was not clearly understood, however, and many drillers were reluctant to use them. DISCUSSION EFFECT OF MUD PROPERTIES ON DRILLING RATE The effect of mud properties on drilling rate has been studied by a number of investigators. 1t is clear from their work that mud properties close to those of water will significantly improve drilling rate and bit life. If the water-type mud will also effectively clean the hole and cause no logging or formation impairment problems, the choice of an appropriate drilling fluid is clear—use water. Often, however, a water-type drilling fluid is not capable of effectively cleaning the hole. THEORY OF PARTICLE SETTLING The forces acting on a particle that is allowed to settle through a fluid quickly reach equilibrium, and the particle settles at some constant velocity referred to as the slip velocity. The slip velocity of any particle depends upon a number of factors such as density and viscosity of the fluid, the volume, specific gravity, shape and roughness of the particle, and upon the shape and area of the projected face of the particle at right angles to the direction of relative fluid solid movement. Brown' expressed this relationship for spheres in Newtonian fluids in the following equation. where v, = slip velocity D, — diameter of sphere p, = density of spheye p, = density of liquid /a = friction factor g = constant. The friction factor f, varies as the size, shape, surface roughness and slip velocity of the body, and as the density and viscosity of the fluid varies. WaddelV ound experimentally that where dynamic similarity exists. f, was a function of the particle Reynolds number (NRe) of the sphere (Fig. 1). Fig. 1 shows that f, for spheres varies from over 10 for low NKe numbers to 0.44 for N,,. over 600.

By D. S. Sanders, E. W. Witcomb

FLOTATION tests, from which the flowsheet for the concentrator was determined, were made in a pilot mill at Chuquicamata and later comparative testing of full size flotation cells was done at the Andes Copper Mining Co. concentrator in Potrerillos. The principal sulphide copper mineral is chalcocite with varying amounts of covellite, enargite, and chalcopyrite. The oxidized portion is principally antlerite, a green basic copper sulphate. The gangue minerals include quartz, sericite, pyrite, feldspars and kaolin. Chuquicamata pit ores have proved to be hard grinding. The results of the flotation and metallurgical work prove that good extraction and concentrate grade can be obtained under a rather wide range of conditions. Metallurgy In general the metallurgy of the ore requires a fairly close control of the grind to the primary rougher flotation and of the regrind of the primary rougher concentrate before cleaning. Regrinding is necessary to reduce the insoluble content of the final concentrate since a large part of the middling combinations are between the copper and silica minerals. The alkalinity of the pulps can vary between wide limits and control of the percent solids gives the desired grind. Alkalinity Control Arroyo Salado water is supplied to the concentrator head tanks. It contains about 5000 ppm of salts but test work shows no deleterious effect. Actually this water permits a decrease of as much as 1 lb of lime per ton of ore as compared to San Pedro water, which is used for leaching oxide ore. About one quarter of the water flow through the concentrator will be new water from the reservoir. The remainder will be reclaimed from the thickeners. For primary grinding and rougher flotation, new and reclaimed water are combined in the head tanks. To avoid erratic results, only new water is used in the regrind system. Milk of lime is added to the rod mill feed chute to obtain the maximum benefit of mixing with the ore. This protects the equipment from corrosion due to entrained acids and soluble copper salts. Lime consumption is 3 to 5 lb per ton of ore. Grinding and Flotation The six bin gates over each belt feeder are opened in controlled combination and sequence to keep a live bed of ore in the bin to prevent arching and to obtain mixing. The milk of lime added ahead of the rod mill is regulated to suit rougher flotation requirements. The primary promoter reagent, Aerofloat 238, is added to the 10-mesh discharge of the rod mill as it is laundered to the ball mill scoop box. The classifier overflow is regulated to produce a grind of about 12 to 15 pct +65 mesh and 60 pct -200 mesh. A secondary promoter Z-4 (aml zanthate) and the pine oil frother are added in the overflow launder where a pH of 10 to 11 is maintained. Comparatively heavy beds of froth on the

Jan 1, 1952

By Harold C. Price

Prior to Sept. 1, 1928, there had never been constructed what might be termed a long pipe line with electric-welded field joints. A year later more than 2500 miles of electric-welded lines had been completed which varied in diameter from 6 to 20 in., and in length from 50 to 700 miles. This paper discusses methods used on five lines with a total length of about 750 miles. The welding equipment used for the firing line or rolling welds, was 300-amp. generators driven with six-cylinder gasoline engines, and for the bell-hole or tie-in welds, 200-amp. generators driven by four-cylinder gasoline engines. A welding gang consisted of a foreman, 6 to 12 firing-line welders and 2 to 4 bell-hole welders, a mechanic and a tractor driver. Coupons about 1/4 in. thick were frequently cut from completed welds, which showed a cross-section of the weld and an indication of its size and penetration. For tests of tensile strength complete welds were cut out. The tensile strength of 52 welds cut from 420 miles of 12-in. line averaged 50,870 Ib. per square inch. The following results give a fair average of the number of welds made per man per day: on 157 miles of 8-in. line both firing-line and hell-hole welds averaged 15.3—the firing-line average was 21; on 39 miles of 10-in. line the firing-line average was 19.9; on 50 miles of 6-in. line, with unfavorable weather, the average was 17.7; on 424 miles of 12-in. line most of which was welded during the spring, 10.3, and with good weather the average rose to 13 welds per day. The average time for making a complete weld on 12-in. pipe 0.313 in. thick was found to be 30 min. for the rolling weld and 45 min. for tie-in welds. A comparison of costs between electric and gas welding shows that the cost of labor for electric welding is 25 per cent. more than gas, generating cost 61 per cent. less than gas, welding wire 40 per cent. less than gas, and supervision and overhead the same. Estimating 50 per cent, annual depreciation on electric welding equipment, and no depreciation

Jan 1, 1930

By F. M. Drake

IN this paper I propose to describe a plant which I lately erected for the Mount Stewart Lead and Silver Mining Company of Leadville, New South Wales, Australia. I am indebted to Mr. W. F. Burrow, of the Roads and Bridges Department of New South Wales, for the drawings which I present herewith, he having reduced and assembled them from my working drawings. The works are situated on a sloping hillside, but sufficient fall mas not available to have the furnace as high as desired, and at the same time have a good slag-tip and sufficient depth on the ore-floor to store a supply of ore and flux. The ore is delivered on the ore-floor (which is of the full width of the furnace-building, and extends back into the hill a distance of seventy feet) by two overhead tramways (not shown in the drawings), one on each side. From these the ore-mixture is made up on one side, while it is being taken to the furnace from the other. The fuel also is delivered by these tramways. The fluxes are stored on a floor directly at the back of the boiler and engine room. The boiler is a Cornish one, 6 feet 6 inches in diameter by 25 feet long. Its flue is 3 feet in diameter and does not contain Galloway tubes. The working-pressure is 40 pounds per square inch. The engine is an old-fashioned one, with a cylinder 16 inches in diameter by 30 inches stroke. Both the engine and boiler had been part of the plant of a defunct gold-mining company. They were very extravagant in their consumption of fuel. The blast is supplied by a rotary pressure-blower, of the Baker pattern, made in England. It has a capacity of 60 cubic feet per revolution. The furnace, which has several novel points, is shown in detail in Figs. 1, 2 and 3. The jackets are of cast-iron, and are higher than those generally used. They are different, too, in that the feedwater inlet is through a hand-hole plate near the bottom. This plate is fastened to the jacket by stud-bolts, and is provided with a baffleplate, which prevents the cooling water from impinging against the inner plate. The outlet is by a goose-neck at the top, which dis-

Jan 1, 1893

By H. B. C. Nitze

Monazite is a phosphate of the rare earths, cerium, lantha num, and didymium (Ce, La, Di)PO,. It also contains thoria (Tho,) and silica, which are present in varying percentages, probably as impurities.

Jan 1, 1896

By David Sinclair, Philip B. Bucky

The dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests. § None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I The Photoelastic Method The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. General Explanation The stress at any point 0 in a structure (Fig. I), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.' To fully identify the stress, the values of P and Q and their directions or angle F must be known.

Jan 1, 1940

By David Sinclair, Philip B. Bucky

The dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests. § None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I The Photoelastic Method The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. General Explanation The stress at any point 0 in a structure (Fig. I), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.' To fully identify the stress, the values of P and Q and their directions or angle F must be known.

Jan 1, 1940

By Maurice Cook

A procedure of obtaining specimens of lead, tin, and cadmium with a moderately equiaxed structure and a smooth surface suitable for etching without grinding and polishing is described; the advantages of general oblique illumination (as opposed to vertical illumination) in the photomicrography of pure metals .are stated. Using these methods, a statistical study of the changes brought about in deformed lead, on annealing, has been made. The common mode of structural change was found to be recrystallization. Cases of growth of one original grain into another were rare; but if a totally recrystallized specimen was annealed above 200° C., a few large grains appeared and spread over the whole area, except for a certain number of small grains which remain unabsorbed. The temperature needed to produce structural change in lead was found to be lower, the greater the degree of deformation. With tin, an extension of 28 per cent. caused practically no recrystallization at ordinary temperatures, but recrystallization occurred if the specimen was heated to 100° C. In cadmium at low temperatures, the grain size decreased in marked manner as the deformation increased; but at high annealing temperatures, the grain size was comparatively independent of the degree of deformation. THE structural changes in metals brought about by annealing following a deformation at a low temperature has been the subject of many investigations. No less than eleven metals and alloys have been studied in some detail; namely, aluminum,1 tungsten,2 iron,3 copper,4 gold,5

Jan 11, 1924

By Victor Homerberg

A STUDY of the correlation of the mechanical properties, and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the manufacturer. The results obtained by Babson and Buhler,1 Bengough and Hudson,2 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470° C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200° C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a ¾ -in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 3, 1924

By Augustus Locke

In 1900, when. the public first heard of "secondary enrichment," the Butte chalcocite seemed clearly supergene. Mining, through successive regions of leached capping, bonanza sulfide, and sulfide less rich, had paused at lean bottom levels which, though chalcocite-bearing, suggested the waning of copper. The deepest chalcocite, at 1500 ft., was yet too shallow to disturb the supergene hypothesis. But, with deeper mining, lean levels yielded to fat ones. Here and there they showed, within the same vein, an inverted distribution, chalcopyrite above and chalcocite below. To the miners' astonishment, they carried chal-cocite, unaffected by cross faults, on an independent course to the depth of 2500 ft. The pattern of ore distribution, hitherto revealed only in fragments, was now appearing in perspective, and, in the depth of the chalcocite, was beginning to make Butte differ from all districts where the chalcocite is indubitably supergene. The idea of hypogene origin at length came into favor; by 1913, when Sales' advocated this origin, the argument had become a powerful one. This argument rested on field evidence; but, already, there was beginning to emerge microscopic evidence not included in this argument. Especially pertinent was the proof that (1) the deep chalcocite lies in-mixed with bornite, often microscopic; (2) the deep chalcocite often replaces bornite; and (3) replacement of bornite by chalcocite is accomplished more easily than that of pyrite, enargite, or chalcopyrite. The microscopic evidence has been accumulating for ten years and it demands

Jan 1, 1924

By H. Ries, R. E. Somers

Bodies of pyritic ore in schistose rocks have long been known in different parts of the world. The several occurrences resemble each other in being usually of more or less lenticular shape, inclosed in walls of schist or gneiss, and carrying pyrite, chalcopyrite, and pyrrhotite in varying proportions, as the chief ore minerals. The deposits differ, however, in that sometimes one, sometimes another, of the three sulphides mentioned may predominate. The orebodies in general are more or less closely conformable with the schistosity of the wall rocks, although in cases this may not hold true. The boundaries may or may not be sharp, but in general are fairly distinct. The lenses vary in size, may occur singly, or in groups; in the latter case they may be in line, overlapping, or occasionally parallel. Pinching and swelling of individual lenses is not uncommon. The genesis of these pyritic bodies has provoked much discussion, and they have been variously classed as sedimentary, igneous intrusions, hydrothermal replacements or impregnations, etc. Indeed, in some cases different geologists have most positively assigned widely diverse origins to the same deposit, as in the case of Rio Tintol and Rammels-berg.2 It is true that in the light of modern criteria, we have been able in a few cases to decipher clearly the process of origin and so there seems no. doubt now regarding the genesis of the deposits at Rio Tinto, Spain;3 Rammelsberg, Germany;4 Ducktown, Tenn.;5 southwestern Virginia;=

Jan 1, 1918