Search Documents

By C. W. Green-Halgh

The accuracy with which grade and tonnage of a mineral deposit may be calculated from diamond-drill assays is dependent upon: (1) the reliability of core and sludge samples and (2) the validity of methods used in grade and tonnage calculations. Limitations imposed by drilling and sampling preclude elaborate methods of computation. In adjusting core and sludge assays the importance assigned the core and sludge samples may be based on either the respective weights recovered or the respective volumes represented by each. Only when core and sludge recoveries arc poor do discrepancies between adjusted assays calculated by these two methods develop, in which case the "weight" method gives emphasis to the core sample and the "volume" method gives emphasis to the sludge sample. When the sludge suffers classification within the drill hole, the weight method gives more accurate results; when the sludge sample suffers no classification, the volume method gives more accurate results. Any drilling campaign offers a compromise between desired accuracy on the one hand and expediency, limited time, money. or facilities on the other. Since the determination of grade and tonnage is an approximation at best, a proper basis for their computation requires a knowledge of the limitations imposed by all phases of work upon which the calculations depend A rational basis for coordination of these phases of work requires determination of: (I) the degree of accuracy desired, as a function of the object of examination; (2) the degree of accuracy attainable, as a function of the limitations imposed in the drilling and sampling program; and (3) the validity of method to be used in calculating grade and tonnage from core and sludge assays. This paper presents results of a comparison made between two commonly used methods of adjusting core and sludge assays, the assumptions upon which these methods are based, and the interrelationship of the phases of work upon which these calculations are dependent. Object of Examination The Purpose of prospecting any mineral deposit is to secure sufficient samples from which Ore grade and tonnage may be calculated. Any mine examination, preliminary or formal, has a definite purpose, although its scope may be limited or broad. The type of examination to be conducted is dependent, therefore, 'pan the reason for instituting the investigation; its scope and thoroughness are directly related to economic considerations. It is highly desirable, therefore, that before starting a drilling campaign a complete understanding of the extent of examination and desired degree of accuracy be determined as a means of simplifying the drilling program and unifying the relative degree of

Jan 1, 1946

By Clarence Zener

IT has long been known that the density of a metal usually decreases with cold-work. Thus O'Neill1 observed as early as 1861 that cold hammering of commercial hot-rolled copper is accompanied by a decrease of density of 0.2 per cent, and that subsequent annealing restores the original density. The origin of this density change, however, has remained obscure. In particular, experiment has not yet decided whether it is due to the presence of small cavities and an increase in intergranular surface or to an actual expansion of the lattice itself. This uncertainty in the origin of the change in density is a reflection of our uncertainty as to the changes induced in a metal by cold-working. One school regards cold-working as a breaking up of the original grains into a large number of perfect crystallites somewhat randomly orientated with respect to one another.2 According to this viewpoint, the mere introduction of a large intercrystallite surface induces a net volume expansion. Another school regards cold-working primarily as a distortion of the grains. It is not obvious that this second viewpoint will lead to a net volume expansion. The purpose of the present paper is to show that this is indeed the case, and that this expansion is of the right order of magnitude to explain existing experimental data. The physical basis for the association of an expansion with distortion lies essentially in the variation of the elastic moduli with volume. This variation is considerable. Thus from Table I we see that a I per cent increase in volume for the case of copper will decrease the bulk modulus K by i0 per cent, the shearing modulus µ by 3.8 per cent. If we thus twist a rod through a given angle, we shall do less work upon it if it increases slightly in volume, thereby reducing the torsion modulus that involves as a factor the shearing modulus. A general principle' in physics states that the rod will so adjust itself as to have a minimum potential energy consistent with the end restraints. It will therefore expand. [ ] In order to obtain a quantitative comparison with experiment, we follow Maier4 in comparing the lattice expansion with the latent energy of cold-work. This latent energy has been measured directly by Taylor and Quinney5 on copper rods subjected to torsion, and may amount to as much as 15 per cent of the total work done upon the specimens. We shall assume that this

Jan 1, 1941

By Walter S. Weeks, Vitaly S. Grishkevich

Considerable difference of opinion seems to exist as to whether the rate of air flow when a fan is placed on a given duct should be determined by the use of static pressure or total pressure characteristics. A little study will show that both methods are correct. Assume that a fan is connected to a duct by an expansion piece as shown in Fig. 1, and that steady flow is established. Considering the atmospheric pressure as zero pressure, let the static head at the outlet of the fan be h and the velocity at this point be vl. The total head at the outlet is then h + „"• The total head at this point must be equal to the total head at the end of the duct plus the losses that have occurred between the two points. Left be the friction loss in the straight duct, s the shock loss in the dif- fuser, and v2 the velocity at the end of the duct. Then ig. 1.—Fan on duct. A curve showing the value of the left-hand side of the equation for different rates of flow is the total pressure characteristic of the fan, while a curve showing the value of the right-hand side is the total pressure characteristic of the duct. If these two curves are plotted on the same chart, the intersection indicates the rate of flow when steady flow is established. We may look at this problem in another way. The static pressure at the outlet of the fan is the static pressure of the fan and it is also the static resistance of the duct from that point to the end. The friction in the straight duct is f. If the duct were the same area as the fan outlet, would be the static resistance of the whole duct system. In the present case, however, this resistance is decreased by the change of velocity head into static head in the expansion piece. If conversion were perfect, the static pressure recovered would be

Jan 1, 1931

By C. G. Albert

The literature of paper technology contains a number of articles having reference to developments in the field of coating and filler clays for use in paper manufacture. Much of this information has not been included in mining publications and has therefore not been readily available to all in the mineral industry. Recent developments in this field, including spray drying of clays, are presented here. U. S. Bureau of Mines figures for 1952 indicate that the paper industry consumes more than 50 pct of all kaolin produced and sold in the U. S. As most of the kaolin used by the industry comes from Georgia producers, the fraction of their output destined for paper use is thus appreciably higher than 50 pct. Small wonder that the kaolin industry, especially in Georgia, is highly sensitive to the quality requirements of paper mills and must respond promptly to technological developments in paper manufacturing.

Oct 1, 1955

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

Birmingham - A City With a Future COURTING new industries is the time honored duty of the chambers of commerce; but Birmingham, until recently, has done its courting without the benefit of troubadors. This is all changed now for the iron and steel industry is singing an enticing song about steel priorities for new industries from Birmingham's own mills. Along with the increasing industrialization of Birmingham there has been a marked influx of industry into the Southeast and neighboring areas in the south central states which augurs well for business in Birmingham. This important stronghold of the foundry industry (consuming 95 pct of Birmingham's merchant pig iron in 1950) has been the source of important announcements about additions to steel ingot capacity. The virtual abolition of basing point pricing gives the Birmingham iron and steel industry an advantage in the South's new markets. This means more business for Birmingham, but the problem of raw materials supplies is posed.

Jan 12, 1950

By A. H. Geisler, J. H. Keeler

Preferred orientations in unalloyed zirconium were determined by the Geiger-counter spectrometer X-ray diffraction technique. With increasing P-annealing temperature the following textures were obtained: l—a retained a-annealing texture, 2—additional orientations predictable from the a-p (Burgers) relationship, and 3—a texture derived from a cube texture in the p phase. Earlier work on cold-worked and a-annealed zirconium was reappraised to show a quantitative dependence of rotations on temperature and to identify spurious areas of some of the pole figures. IN a previous paper,' the preferred orientations of high purity zirconium sheet were described for cold-rolled and annealed samples. Annealing temperatures up to 900°C, which is slightly above the allotropic transformation temperature, were explored. Of interest was the observation that the orientation of the hexagonal-close-packed material after annealing in the temperature range of the stable body-centered-cubic phase was similar to that of the material which had been annealed in the a temperature region, although a change in texture would be expected because of the many new orientations based on an orientation relationship between the two forms of zirconium. The reversion to an original orientation after an allotropic transformation cycle is not unusual. It has been found for titanium,"* for thallium," and for cobaltB among the hexagonal metals. Burgers found in his original work7 that, when zirconium was cooled through the allotropic transformation and then reheated, the body-centered-cubic phase reverted to the original orientation. Additional experimental work has been carried out to further explore the textures of zirconium after annealing in the temperature range above the allotropic transformation. In addition, a reappraisal was made of the earlier results for zirconium' in light of recent work on titanium4 which has shown that the texture type depends quantitatively on the temperature of annealing and that spurious areas may be encountered in the pole figures of hexagonal metals determined by the X-ray spectrogoniometer technique of analysis. Experimental Procedure Crystal-bar zirconium prepared by the iodide process was the material used in this investigation. The major impurity was hafnium which was less than 0.3 pct. The composition obtained by spectro-graphic analysis is given in Table I. Cold-rolled specimens were prepared from crystal bar by a series of reductions of approximately 0.010 in. until the sheet reached a thickness of 0.010 in., after which it was cold rolled to 0.001 in. thickness between sheets of alloy steel. The total cold reduction amounted to about 99.8 pct. Specimens were annealed for % hr at 1000" to 1100" to 1200°C or 1 hr at 1400°C in an evacuated Vycor or quartz tube. The transmission pole figures were obtained by

Jan 1, 1956

By E. A. Cisney

The formula for calculating the crystallographic angles of a tetragonal lattice is: C°S =where $ is the angle between planes (HKL) and (hkl). The angles in Table I have been calculated for indium

Jan 1, 1960

By E. J. Rapperport, J. P. Pemsler

We have made calculations to evaluate the sensitivity of atomic absorption as a technique to measure vapor pressure changes with temperature. Our conclusion, supported by the experimental findings presented in this work, is that the ultimate sensitivity of the technique is well below lo-' Torr. This magnitude of vapor pressure sensitivity makes the method extremely attractive for thermodynamic studies. Atomic absorption techniques have been used previously in this connection by Scatchard and Boyd' and by vidale2 with a much lower sensitivity reported. Scatchard and Boyd's work measured cadmium pressure over Ag-Cd alloys in the range 0.02 to 0.3 Torr, and Vidale estimated that sensitivities of only 10"5 to 10"6 Torr are to be expected. Atomic absorption appears to be particularly well-suited to thermodynamic studies for several reasons: A) It is extremely sensitive; our experiments indicate an ability to measure vapor pressure changes of 10"9 Torr. B) It is highly selective; there is seldom interference among the resonant wavelengths of the various species. C) It may be performed in an absorption cell under static conditions. This alleviates such problems as surface impoverishment of alloys, attainment of equilibrium, and temperature measurement and control. D) Simultaneous, or near-simultaneous, vapor pressure measurements may be made for several elements in a given system. Experimental. The physical basis of the technique is the highly selective absorption of particular wavelengths by specific atomic species. In most atomic absorption work the element of interest is incorporated into a hollow cathode lamp to provide a characteristic spectral source of high intensity. The spectra lines characteristic of the element in the cathode are attenuated by atoms of that element in the radiation path. Radiation from silver or cadmium hollow cathode lamps was directed along a path containing a 10-cm evacuated silica cell. The cell was positioned within a silica windowed furnace and contained silver, cadmium, or an Ag-Cd alloy. As the furnace temperature was elevated, the number of atoms of the absorbing element in the vapor phase within the cell rose, and the resonant radiation was increasingly absorbed. Intensities were measured by passing the radiation through a Techtron Model AA-4 one-half meter grating atomic absorption spectrometer equipped with a photo-multiplier detector. In order to minimize instabilities in the source, the hollow cathodes were allowed to warm up for several hours and were run at only 2 5 to 30 pct of their maximum rated amperage. In addition the attenuated beam was monitored before and after each reading. The attenuation of resonant wavelengths may be related to vapor pressure by the following relationships.

Jan 1, 1969

NORMAN B. PILLING (author's reply to discussion *).-The discussion by Mr, Bassett raised one or two points that deserve further discussion. The printed figure for the lead content of the copper used was 0.015 per cent. and not 0.15 per cent., upon which his comment was based. A copper having the latter figure would, of course, be quite unusual. Mr. Bassett takes exception to the writer's statement regarding the distribution of cuprous oxide in wrought copper and states that "the FIG. 1.--ROLLED AND ANNEALED SHEET. ETCHED WITH AMMONIA AND HYDROGEN PEROXIDE. X 75. eutectic of copper with cuprous oxide is usually found between the crystals of pure copper, whether in the cast or the wrought form." While it is very well known that during the solidification of cast copper the cuprous oxide is segregated completely as an envelope of cuprous oxide-copper eutectic around the crystals of copper free from oxide, it is the writer's opinion that, as a result of repeated rolling, this eutectic structure is quite destroyed and the small particles of cuprous oxide become widely scattered, and in the recrystallization following, during annealing, the rearrangement of the grain boundaries takes place with much indifference to the actual distribution of these particles. In the accompanying micrograph, taken from a rolled and annealed sheet, the random distribution of the small cuprous-oxide particles with reference to the location of the grain boundaries may be seen.

Jan 3, 1919

By J. H. Frye, R. M. Treco

One of the chief hindrances to an understanding of the hardness of solid solutions is the sparsity of suitable hardness data. There is great need of a large body of hardness data obtained from many different alloys of high purity by identical testing methods and corrected to correspond to a single grain size. A considerable amount of such data has been obtained by means of the Meyer analysis on copper-rich and silver-rich solid solutions. There are enough of these data to permit comparison of numerous alloys at equal solute concentration in these two solvents, but only in a few cases is it possible to construct hardness-concentration curves for any given alloy. Therefore additional hardness work on most of these alloys is desirable. The primary solid solutions of silver with cadmium, indium, tin, or antimony as solute are of special interest, since all elements are from the same period of the periodic table and since, as shown previously,l the hardening effect of equal percentages of these solutes is proportional to the lattice expansion produced by them. This paper presents the relation between hardness and concentration in the silver-antimony system from very dilute to nearly saturated solutions of antimony in silver. Experimental Procedure Alloys were made from silver, 99.99 per cent pure, and antimony, 99.975 per cent pure. Silver and antimony were placed in graphite crucibles that had an ash content of less than 0.7 5 per cent. These metals were melted and allowed to solidify in a vacuum, which, after melting was corn- . plete, was usually equivalent to 3 mm. of mercury. A high-frequency furnace was used. The ingots so obtained were worked and annealed to lessen segregation and to control grain size. Annealing was done in evacuated and sealed glass tubes. Hardness measuremeuts on specimens from these ingots were by means of the Meyer analysis.394 Using a 4-mm. ball, impressions were made under seven loads from 25 to 400 kg. The diameter of impression made under each load was measured. This enabled calculation of the constants in the well-known formula of Meyer. L = adn where L = load, d = diameter of impression, a = a constant, n = a constant The Meyer hardness is defined as P = L/i(1/4pd2) or P = 4adn-2/p Meyer hardnesses corresponding to d = I and to d = 4 are of especial interest, since the first corresponds to comparatively slight 'plastic deformation and the second to the maximum plastic deformation producible by penetration of the ball. These

Jan 1, 1945

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By Frederick W. DeVries

Since we first agreed to present this talk we have learned that some of you may have been covering ground we intend to discuss: Bob Schechter, Daryl Tweeton, Don Seidel, Herb Burgman; however, the ideas were original when we began, "novel" as in the title of the talk, and whether our results are news or merely corroborative, we feel they point a direction that could be valuable to all. We worked with many of you in the past on using hydrogen peroxide in in-situ uranium leaching. Our talk today is not directly related to peroxide; it is, I hope, illustrative of Du Pont&apos;s interest in providing service to this industry in any way we can. The scouting work we are presenting was stimulated by field inputs: First, ammonium carbonate leaches cause restoration problems, primarily because ammonium ions exchange on clays with calcium. Second, sodium carbonate solutions, especially in South Texas deposits, can cause intolerable swelling of clays. From discussions with Dr. van Olphen, who wrote the book on clay chemistry, we inferred by comparison of the radii of the hydrated ions of the elements in these clay systems, that since potassium had about the same radius as ammonium, and sodium was much larger, potassium occupied a unique position to solve both problems. We have shown: FIGURE 1 Potassium bicarbonate systems leach uranium without loss of permeability found with sodium Potassium salts are very effective in restoring ammonia-leached sites Before reviewing the details of our work, which was performed by Hazen Research, Inc., I should like to stress its scouting nature. We are trying to assist the in-situ industry by pointing out new, potentially important directions. But, as with our previous work on sodium silicate to restore permeability, we feel the development phases can generally best be carried out in cooperative programs with companies directly involved with operations. DISCUSSION Test Parameters Now for the details: Our leaching tests were designed to note pressure-drop changes across the ore sample as the uranium was leached. Figure 2 shows the apparatus. The [ ] packed length was 20.5 inches (52 cm) with fifteen hundred grams of ore in the two-inch (5 cm)-diameter bed. Pressure drop was measured by manometer and feed rates were maintained constant with a tubing pump. The samples, from a South Texas leach site, were sealed in "Zip Loc" bags, frozen with "dry ice", crushed (still frozen) through six mesh, and blended before placement into the columns. The ores analyzed as shown here: FIGURE 3 Ore Analyses [Sample A Sample B U308 015% 0122% Mo 0004% 0086% Se0012% <0001% Fe3,078%076% Fee- 098% 044%]

Jan 1, 1979

By R. K. McGeary, B. Lustman

Orientation relationships and rates of annealing of 97 pct cold rolled zirconium have been studied by X-ray techniques, metallography, and by hardness measurements. The process of annealing occurring by the formation of domains, and their subsequent growth without recrystallization, is demonstrated. NUMEROUS investigators1-&apos; have revealed sub-grain formation after annealing cold worked metal single crystals and have generally described the results in terms of a dislocation mechanism of polygonization.5,6 in heavily cold rolled polycrystal-line aluminum the first stages of heating cause an apparently spontaneous subdivision of regions of the deformed matrix into a great number of slightly disoriented domains followed or accompanied by rapid growth of certain domains to form a recrystallization texture.7,8 In the present investigation the isothermal rate of annealing of cold worked polycrystalline zirconium has been studied by X-ray techniques, metallography, and by hardness measurement. It will be shown that, rather than by the usual nucleation and growth mechanism,"12 the process of annealing can best be explained by the formation of domains early in the annealing treatment and the subsequent growth of these domains without recrystallization. Experimental Procedure All the experimental work was performed on an arc-melted ingot of high purity zirconium crystal bar made by Westinghouse in a production scale deBoer unit. The weight percentage of impurities in the zirconium were as follows: C, 0.04; Fe, 0.05; Hf, 0.014; W, 0.01; Ti, Ni, and Al, 0.003; Si and N, 0.002; Cr and Cu, 0.001. Metallographically the zirconium showed only a single phase. The 4 in. diarn ingot was forged at 760°C to a 1 1/2x3 in. plate and was then rolled at 760°C to 0.150 in. thickness and annealed at this temperature for 20 min to produce an equiaxed grain structure of about 0.1 mm average grain diameter. The hot rolled plate was roller-leveled, surface ground to 0.135 in., cold rolled 83 pct reduction in thickness on a two-high mill, and then to a total reduction of 97 pct on a Sendzimir mill. The 0.004 in. strip material so produced received no subsequent mechanical treatment. Specimens % in. square were sheared from the rolled strip and isothermally annealed at 104 mm Hg in an all glass vacuum system equipped with a Vycor furnace tube. The temperature data presented are the average temperatures during the runs and did not vary more than about k3"C. X-ray Diffraction Methods: When zirconium is drastically cold rolled, a high degree of preferred orientation results in which prism poles, {1010}, are perpendicular to the rolling direction. After fully annealing this material an entirely new texture develops which corresponds to a 20" or 40" rotation of the deformation texture about hexagonal axes of

Jan 1, 1954

By Roy A. Hardy

THE Getchell mine is a comparatively recent discovery in the old Potosi mining district, Humboldt County, Nevada, a district organized in the seventies and eighties, in which some prospecting was done in several metamorphic zones along a monzonite-sedimentary contact. The district had no production in the early days and no further work was done until the same metamorphic zones were prospected for tungsten (scheelite) in 1917 and 1918, when a few small lots were shipped. It again lay dormant until 1934, when prospectors investigated a large siliceous escarpment at one end of the old district where outcroppings were a prominent feature of the topography. Undoubtedly, during the early prospecting of the district, the outcroppings had been investigated for mineral, probably by panning, with negligible results because the gold later found is invisible in the concentrate and is refractory. A fire assay revealed the presence of sufficient gold to warrant development work. The outcroppings were easily prospected by short tunnels having their portals in the siliceous material on the hanging-wall side, with a maximum distance to crosscut to the footwall of 135 ft., or a distance at right angle to dip of 60 to 90 ft. Development work, reaching a depth of over 600 ft. on the dip of the vein, was done by means of various crosscut tunnels, winzes and laterals. A churn-drill hole was also sunk, which intersected the vein at a depth of 1100 ft. on the dip. Sufficient development work of this character was completed by 1937 to justify the erection of a reduction plant to roast the sulphide ore and cyanide the calcine, and to treat the oxidized ore by straight cyanidation, to make a doré bullion for shipment to the mint. The erection of the plant was started that year and finished early in 1938, with a combined capacity of about 800 tons per day. It has operated continuously since erection and recently was enlarged to handle 1000 tons per day. The vein dips with the slope of the mountain, and by stripping the hanging wall the ore may be mined by power shovel for several hundred feet below the outcrop. Thereafter underground methods will be necessary.

Jan 1, 1940

RICHARD A. CONKLING (communication to the Secretary*).-Mr. Hager says that his results on the correlation of well logs in the north Cushing field are the opposite to those of the author. Can he, then, explain why the structural dip of the formations increases with depth, as Dr. Ohern, in his criticism, sets forth that it does, and as all who have worked in these fields will admit, if the shales thicken on the crest of the anticline, as he says they do? We are willing to agree with Dr. Ohern that there is some evidence of a slight unconformity below the Bartlesville sand and think that we can prove, from a specimen in our office, that .this unconformity comes at the base of the Bartlesville sand in the south Cushing pool. On the Ingalls dome, in the southeast corner of Township 19 North, Range 4 East, however, we get results the same as those given by the author on Cushing. The Ballard well in the center of the Northeast Quarter of Section 33 is just 10 ft. higher, structurally, according to tile, surface contour, than the Ringold well -in the center of the Southwest Quarter of Section 34. The dip in the Bartlesville sand, between these wells, is 40 ft. and the dip on the top of the Mississippi lime is 75 ft. This also might be accounted for, partly by the unconformity, but the author used the interval between the top of the Oswego lime, which is about 420 ft. above the Bartlesville sand, and the oil horizon found in the lime in the Ballard well-just mentioned above-to find the depth at which the same oil should be found in a well in Section 5, Township 22 North, Range 3 East, 25 miles North. Using this interval below the Oswego in the former well, we predicted within 2 ft. where they would find the oil in the latter well. Of course, we know that it was accidental that we missed it only by 2 ft., but if there were much of an unconformity in this interval it would be more of an accident if we came within 100 ft. of the depth. Since it can be proven from most of the structures in this section that the clip continues to increase downward, below the Bartlesville at least, to the Mississippi lime, it does not seem necessary to the author to try to prove otherwise that the depth at which the shales will tend to thicken on top of a fold, has not been reached above the

Jan 6, 1917

By C. E. Birchenall, R. H. Condit, M. J. Brabers

In the oxidation of pure iron above 700°C the overall rate is determined mainly by the rapid growth of wiistite, through which iron ions can diffuse rapidly.&apos; Nickel added to the iron progressively decreases the stable range of composition of wustite.&apos; When enough nickel is added to eliminate wiistite as a stable phase, the spinel is the fast growing phase. This investigation was undertaken to test the hypothesis that nickel substituting for iron in magnetite might decrease the rate of spinel growth by reducing the iron mobility. Nickel ferrite boules grown by the flame fusion process were purchased from the Linde Co. Chemical analysis gave an atomic ratio of iron to nickel of 2.88 and showed no other cations. They were cut into discs and ground to give flat, parallel faces. The experimental procedure employed was like that of Eisen and Birchenall in which the distribution of radioactivity diffused in from a vapor deposited surface layer was determined by counting the residual activity through a series of ground faces. The diffusivities were calculated in a manner consistent with the requirements discussed by Condit and BirchenallP The details will be given in connection with a more extensive spinel diffusion study now in progress. The results of the measurements are shown in the figure in comparison with earlier data on magnetite1 and zinc ferrite. The uncertainties arising from scatter in the activity vs distance relationship and uncertainties in the temperatures are shown by flags. Despite the scatter it is clear that substitution of a considerable part of the iron in magnetite by nickel, in this case about one third decreases the iron mobility substantially. sachs&apos; determination of the distribution of iron and nickel in scales on iron-nickel alloys appears to show that nickel is less mobile than iron in the spinel layer. It is evident, therefore, that nickel plays several roles in reducing the oxidation rate of iron-nickel alloys. 1) It reduces progressively the stability range of wiistite. &apos; 2) It reduces progressively the stability range of the iron-nickel spinel phase in terms of the variation in cation to anion ratio.&apos; 3) As shown in this investigation, it reduces the cation mobility in the spinel phase which is the faster growing phase in the absence of wiistite. The fe was obtained from the Oak Ridge National Laboratory. The research was supported by the Air Force Office of Scientific Research (ARDC) under contract number AF 18(600)-967.

Jan 1, 1961

By D. C. Buffum, L. D. Jaffee

QUANTITATIVE measurements of the temper brittleness of steel are made by comparing the difference between embrittled and unembrittled specimens in the temperature of transition from ductile to brittle fracture. Since hardness affects the transition temperature, a study of the combined effects of hardness and temper brittleness appeared desirable. In this investigation a commercial SAE 3140 steel, which has been reported on previously in temper brittleness studies,* was used. Blanks from this steel were austenitized for 1 hr at 900°C and water quenched. The blanks were then divided into six groups and further heat treated as follows: Group 1—tempered at 675°C for 4 hr and water quenched; Groups 2, 3, 4, and 5—tempered at 675", 650°, 625&apos;, and 600 °C respectively for 1 hr and water quenched; and Group 6—tempered at 500°C for y2 hr and water quenched. Each of these groups was divided into two parts; one part was tested without further heat treatment, and the other was embrittled for 48 hr at 500°C and water quenched. Tempering treatments between 500" and 600°C were avoided because of the rapid embrittlement occurring in that range for this steel. The heat-treated blanks were machined into standard V-notched Charpy bars. Each group was tested over a range of temperatures on a 217 ft-lb Charpy machine. The energies necessary to fracture the bars and the percentage fibrous fracture of each bar were recorded. The transition temperatures were obtained from a plot of the percentage fibrous fracture as a function of testing temperature. They were taken as the lowest point on these curves at which the fracture was 100 pct fibrous. The transition temperatures for both embrittled and unembrittled specimens are presented in Fig. 1 as function of the hardness. It will be noticed in this figure that the point for the unembrittled condition at 21 Rockwell C is out of line. These specimens were tempered for 4 hr at 675 °C and this point indicated that under isothermal conditions at this temperature, as is well known, embrittlement may develop fast enough to more than offset the effects of softening. From this data, it was concluded that the difference between transition temperatures for the embrittled and unembrittled conditions at any given hardness, within the range of Rockwell C 24 % to 32lh, is constant. It is also concluded that, within the hardness range studied, the transition temperatures for embrittled and unembrittled specimens rise in a parallel fashion with an increase in hardness. The authors wish to acknowledge the assistance of Frank Carr in this work.

Jan 1, 1952