Search Documents

By Richard Hamburger

(1) Introduction: The purpose of this paper is to call attention to certain methods which will shorten and simplify the calculation of plane tri-angulation. These methods, though not new,',2 do not appear to have been properly publicized in the United States. The cotangent (or tangent) solution of a triangle permits calculation of coordinates in a smooth series of operations of the calculating machine with a minimum of notation. The semigraphical solution permits the simultaneous solution of a number of intersections, at one station, without the added burden of solving additional triangles. This in turn encourages more numerous field checks and more complete office computation than would normally be undertaken. RICHARD HAMBURGER, Junior Member AIME, is Junior Engineer, Inspiration Consolidated Copper Co., Inspiration, Arizona. TP 2798 A. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Tables I and I1 show the distinct advantage which the combined use of the cotangent and the semi-graphical solutions hold over, what might well be called, the standard solution. It will be shown that the positions for the entire net in fig. 1 may be calculated without computing any distances, thus saving much computation. (2) Comparison of Cotangent and Standard Solutions: To compare the cotangent method with the standard method, the notation involved in the solution of triangle 1-X-4, fig. 1, by both methods is shown. Fig. 2 shows the given information, that is, the coordinates and azimuths of Stations 1 and 4, and angles of the triangle or the azimuths from Stations 1 and 4 to Station X. (Azimuths are used here because the author feels that they are easier to handle, but bearings may be used by those who prefer them). It will be seen from the above comparison that the advantages of the cotangent solution of a triangle are: (a) rapidity, (b) full use of the calculating machine, (c) the small number of

Jan 1, 1951

By C. E. Nelson, T. E. Leontis

THE properties and casting characteristics of sand-cast Mg-Al-Zn alloys, used commercially in this country and abroad, have been discussed in a number of articles during the past few years.'-" In addition, broad surveys of many compositions in the magnesium corner of the Mg-Al-Zn diagram between 0 and 12 pct A1 and 0 and 6 pct Zn have been presented by Busk and Marande7 and by Fox." The purpose of this paper is to furnish a comprehensive survey of the changes in tensile properties, micro-structure, and dimensional stability of two magnesium alloys, AZ92A and AZ63A,+ as a function of aging time and temperature after solution heat treatment. Rates of precipitation in Mg-Al-Zn alloys are slow enough so that a substantially homogeneous, supersaturated solid solution can be maintained even when these alloys are air-cooled from the heat-treating temperature. Consequently, even though it has been demonstrated9 10 that significantly higher strengths can be developed in some alloys in the aged condition by quenching rather than air cooling from the heat-treating temperature, general practice is to air-cool magnesium alloys. All the work discussed in this paper is based, therefore, on aging studies performed on material air-cooled from the heat-treating temperature. This investigation was intended to be a study of commercially practical aging cycles; the tensile properties were determined, therefore, up to aging times of 25-hr duration. The alloys, used in this investigation were prepared in the laboratory by remelting commercial ingots of the appropriate composition according to the procedures described in a previous paper" as the "crucible method." All melts were given the standard superheating treatment in order to insure the maintenance of a uniform grain size of 0.003 to 0.004 in. Standard test bars, 61/2 in. long with a 2½ in. long reduced section having a diameter of Y2 in., were cast from these melts in green-sand molds using a four-bar pattern. The alloys were heat treated according to the following schedules: AZ92A alloy: 500" to 780°F in 2 hr + 780°F (24 hr) AZ63Aalloy: 500" to740°Fin2 hr + 740°F (16hr) In commercial practice," AZ92A alloy is heat treated at 770°F for 18 hr and AZ63A alloy is heat treated at 730°F for 10 hr. The slightly higher temperatures and longer periods of heat treatment were used in order to obtain as homogeneous a solid solution as possible and thus to minimize inconsistencies in the

Jan 1, 1952

Ocean engineers and technologists will assemble in Houston, Texas, during May 3-6, 1976, for the Eighth Offshore Technology Conference (OTC) . More than 50,000 members of industry, government, and academia from 94 nations will participate in what is generally acknowledged as the offshore industry's show-of-shows. A well-diversified 280-paper technical program has been divided into 42 general sessions that range from seafloor surveying and offshore mining to navigation systems and environmental issues. In addition, the largest technical- educational exhibition in the conference's eight-year history will augment the OTC '76 program.

Jan 4, 1976

By W. Rostoker, H. Nichols

It has been demonstrated in previous work1'2 that wetting of aluminum alloys by liquid mercury can cause fracture to occur with substantial suppression of prior plastic flow. This has been interpreted as the action of a critical liquid species in reducing the cohesive strength of a stressed solid at sites of potential crack nucleation. In this way the critical transverse stress for fracture nucleation is reached at much lower stresses than is normally the case. The stresses for both fracture nucleation and fracture propagation are depressed by the same mechanism. In so doing the plastic-energy component of fracture energy is reduced to a level which is of the same order of magnitude as the surface, interfacial, or cleavage energy. Recent work2 has illustrated the influence of dispersed precipitates, cold work, and combinations of these on brittle fracture associated with plastic strains of the microyield order of magnitude. This has been rationalized in terms of the contribution of internal microstress fields to the stress magnifications at points of obstruction of active slip bands in a stressed metal. The presently reported studies on an Al-4-1/2 pct Mg alloy amplify this subject by introducing thermal-mechanical conditions which can produce strain aging. As amply demonstrated by Phillips, Swain, and borall, the tensile behavior of aluminum alloys containing magnesium reveals a yield-point elongation and successive discontinuous elongations over the whole plastic-strain range. This gives a stepped or serrated character to the stress-strain diagram. The yield-point elongation is not temperature-dependent. On the other hand, the discontinuous extensions in the plastic-strain range are gradually suppressed by lower temperatures of testing. At -78"C, only the yield-point elongation persists. The yield-point elongation itself can be suppressed by rapid quenching to room temperature from an annealing temperature of 500°C. The argument presented by Phillips et 1. and Cottre114 is that the yield-point elongation derives from surmounting at a critical stress the restraint to slip by grain boundaries which have been reinforced by appreciable magnesium-atom segregation. The serrated character of the plastic-strain range is the result of rapid strain aging during the test. This is made possible by the inevitable proximity of magnesium atoms to any dislocation line. In the Al-4-1/2 pct Mg alloy there is one magnesium atom for every twenty-two aluminum atoms and, with a coordination number of 12, a magnesium atom is on the average only about two atomic distances from any given lattice site. Rapid strain aging is therefore a reasonable expectation. A study of mercury embrittlement of the Al-4-1/2 pct Mg alloy (commercial designation 5083) provides an opportunity to relate the interplay of grain size, grain boundary restraint to slip and strain aging in the brittle-fracture process. One lot of commercial sheet material of 0.125-in. thickness was used for all of the tests. The specimen shape and test procedures used were the same as those described in a previous publication.2 A range of grain sizes between 0.0057 and 0.0125 mm was produced by various combinations of plastic prestrain and annealing. The coarsest grain was somewhat elongated in shape. In this case the measurement was taken in the direction transverse to the axis of tension as more meaningful to a brittle-fracture process. In the annealed condition, specimens wetted with mercury failed with zero permanent elongation at stresses slightly below the normal yield point, i.e., stresses at 0.05 to 0.2 pct strain. Since this occurs before yield-point elongation can begin, fracture derives from slip contained within individual grains and restrained from propagating across grain boundaries. No significant difference in wetted fracture stress was observed between specimens which had been water-quenched or furnace-cooled from the annealing temperatures. This signifies that the degree of magnesium segregation at grain boundaries

Jan 1, 1964

By K. Shoji, R. Hogg, L. G. Austin

The flow of dry powders through continuous ball mills has been investigated. Based on a physical model of the system, expressions have been derived which relate the holdup of material in the mill and its variation along the length of the mill to the mill dimensions, speed of rotation, material feed rate, and the mill discharge geometry. Experimental results obtained in a small (4 in.) mill using 3/8-in. steel balls and a feed of silicon carbide particles are in good agreement with the prediction of the model.

Jan 1, 1976

The American Association of Petroleum Geologists, P. 0. Box 1552, Tulsa, Okla. J. P. D. Hull, Business Manager. The official publication of this Association is the Bulletin of the American Association of Petroleum Geologists, issued monthly. It contains illustrated papers, maps, current notes, discussions, reviews and personals. Annual subscription is $15 ($15.40 outside the United States). Back numbers of the Bulletin, practically all of which are available, cost from $1.50 to $3 each; for several years back a uniform price of $1.50 each is charged.

Jan 1, 1933

Organization Place 1917 National Association of Stationary Engineers .... Evansville, Ind. Sept. 10-15 National Safety Council New York City. Sept. 10-15 National Exposition of Safety and Sanitation.... New York City. Sept. 10-15 American Iron, Steel & Electrical Engineers Philadelphia, Pa. Sept. 10-14 American Association of Port Authorities Cleveland, Ohio. Sept. 11-14 American Institute of Metals Boston, Mass. - Sept. 24-29 American Foundrymen's Association Boston, Mass. Sept. 24-29 Chemical Industries, Third National Exhibition.. New York City. Sept. 24-29 American Electrochemical Society Pittsburgh, Pa. Oct. 3-6

Jan 9, 1917

By L. Adler

The author recently proposed a technique for handling the effect of planes of weakness on failure in geologic material.1 The technique employed an "extended" Mohr's rupture envelope, on which was superimposed a generalized three dimensional stress representation. Subsequently, the method was applied to so-called two-dimensional stress states" which were in reality degenerate three-dimensional ones. Since a two-dimensional stress solution usually refers to a plane stress condition, the terminology was confusing. The distinction between a plane stress state and a degenerate three-dimensional one is shown in Fig. 1. The solution of problems involving a generalized three-dimensional stress state is greatly aided by continual reference to the basic principle that no stress components can act on a plane, oriented as is the weakness plane, which lies outside of the weakness plane's rupture enVelope.2 This is shown in Fig. 2; and if it is also remembered that the radii of the Mohr's Circles give the orientation of such a plane, solutions are easier to follow, and perform. Sample Problem 1: Site Location (generalized three-dimensional case).' Given: 1) Both rupture envelope for the solid and plane of weakness. 2) Existing principal stresses and orientations in space (?12, ?13) obtained from a stress analysis of the proposed structure. Find: Permissible orientations of the weakness plane in order to select a suitable site.

Jan 1, 1963

By D. A. Munro, G. P. Contractor

Fourteen 50-lb laboratory melts were investigated to determine the effect of uranium on the tenpering characteristics of loo-carbon (0.06 to 0.1 pct C) steels. It was found that uranium additions, particularly in the range 0.30 to 0.45 pct, enhanced the hardness and both ultimate and yield strength of the experivzental steels in the quenched and tempered condition. The structural and morphological chazges indicated that uranium retarded tempering of the tnartensite, thereby hindering the normal formation of polygonal ferrite formed in the late stages of tempering. The effect of this was to make possible the re-tension of the acicilar ferritic structure in the uranium-bearing' steels. The iraniuin-bearing steels also showed IVidnzanstatten-type growth of ferrite plates and had large prior austenite grains containing assenzblies of fine ferrite grains, mainly acicular in geometry. The fine-grained ferrite structure and the presence of more numerous and apparently smaller precipitates in the uranium-bearing steels are thought to he principally responsible for the itnproved tensile strength and hardness of the experinzental uranium-bearing steels. At ternperirzg temperatures above 455% (850'F) the ferrite in the higher-uraniun steels nzaintained acicularity and, hence, its strength and resistance to tempering. Uranium did not produce a secondary hardening peak. However, it retarded softening during the third stage of tempering because of its effect of inhibiting the grouth of cementite particles and of retaining the acicularity of ferrite plates. The resistance to coalescence accounted for the slow grocth of the ferrite grains in the uranium-modified steels and, hence, fov the persistence of the acicular ferrite structure. IT had been found previously1 that uranium additions up to about 0.45 pct had no significant effect on the tensile properties of low-carbon steel (0.06 to 0.10 pct C) in the as-rolled and normalized conditions, Fig. 1. On the other hand, it was observed that uranium in excess of about 0.30 pct had an embrittling effect as revealed by Charpy V-notch impact results. It was also noted that, as the uranium content increased, the morphology of pearlite changed from lamellar to feathery and the ferrite grains showed an etching effect resembling striated or dashed markings, suggestive of precipitation. The sharp drop in the impact properties shown in Fig. 2 warranted an assumption that the uranium content of about 0.30 to 0.45 pct may produce some secondary hardening reaction on tempering, analogous to that associated with a Cr-Mo-V steel, which shows very poor CVN toughness at the secondary hardness peak in the tempering curve.1' With this background and the reported findings of Hasegawa and noda that low-carbon uranium-treated steel showed signs of secondary hardening, the present investigation was undertaken to determine the effect of uranium additions on the mechanical properties of 0.10 pct C steels. No attempts were made to investigate in detail the mechanisms of hardening, although some suggestions based on the experiments are made. MATERIALS AND PROCEDURES A series of 50-lb induction-furnace melts was made using AISI 1008 rimming steel billets as the melting stock. The melting, forging, and rolling techniques proven satisfactory in previous projects'-3 were employed as a guide for this investigation. The steel was deoxidized with aluminum (2 lb per ton) prior to the addition of high-purity uranium. The analysis of each melt is given in Table I. Properties were evaluated as a function of heat treatment and are presented in terms of hardness and tensile strength vs tempering temperatures. The variation of hardness with the tempering temperature was studied on the quenched and tempered specimens, some of which measured 0.50 by 0.25 in. diam and the others 0.40-in. cubes. Before quenching, the specimens were vacuum-sealed in glass tubes and normalized at 900°C (1650°F) for 20 min. Following this treatment, the sealed specimens were hardened by austenitizing at 955°C (1750°F) for 20 min and water quenching, and then tempered for 1 hr in the range 150 to 730°C

Jan 1, 1967

By Lawrence Adler

Any design of a mine roof in bedded deposits which ignores differential deflections at the supports can quickly lead to dangerous overstressing. As illustrated by the typical case presented on page 1029, if one support deflects only 0.1 in. more than its neighbor, stresses 50 pct higher than anticipated will result. Previous studies1-3 have assumed that the mine roof acts like a beam clamped at both ends, with no deflection or slope4 at the supports (Fig. 1). Essentially this assumes:5,6 [BA = OD = 0 and dA = dB = 0.]

Jan 10, 1959

By C. S. Simons, G. Major-Marothy, M. A. K. Grice, D. A. Dahlstrom

The vacuum filter operating variables that influence cake moisture are discussed. The influence of temperature control, particularly through application of steam to the cake, is emphasized. Results of pilot plant studies on filtration of fine hematite concentrates are presented and discussed, and are shown to support the theoretically-derived conclusions. Results on fine magnetite concentrates are also used to support the argument. The relative merits of disc and drum filters from the standpoint of cake moisture are discussed. Moisture content has always been recognized as one of the most important properties of concentrates used as pellet plant feed. Most iron ore concentrates are produced by wet methods, and are finally de-watered on filters. Obviously, a real economic advantage accrues to the ability of control the moisture content of the filter cake within the range required for optimum pellet production. Another consideration, also, has been receiving increasing attention recently. Transoceanic shippers of concentrate cargoes are critically assessing the hazards of excess moisture. The nature and magnitude of these risks have been described, ' and it appears that their elimination may require that residual moisture be somewhat lower than the limit for proper pelletization. Coarse, very free-filtering materials, such as the products of spirals, are usually best handled on top-feed types of machines. The moisture content of the cake may be held at a specified value by proper design and operation, taking into account cake thickness, air-flow rate, and drainage time. Fine-grained concentrates, with which we will be concerned here, must be filtered on Drum or Agidisc machines. With many of these materials, it is possible, by proper design, to meet cake moisture requirements with a conventional filter station. The first installations to produce high-grade pellets from magnetic taconites fell in this class. In fact, the design criteria were developed in connection with operations of Reserve Mining Co. at Silver Bay, inn.,2 and these have been verified repeatedly in other mills. The trend today, however, is toward the production of more difficultly dewatered concentrates. This is due on the one hand to the increasing attention being given to non-magnetic ores, which tend to be far slimier, and therefore much more retentive of moisture, than the magnetites. On the other hand, the pressure to improve the grade of the magnetic ores is leading to finer grinds, which also are more difficult to dewater. In the latter case, the decision to improve grade in an existing operation by finer grinding for better liberation may lead to two unattractive alternatives: 1) substantially higher bentonite consumption, plus the risk of poorer quality pellets, from high cake moisture, or 2) installation of a thermal dryer. There is, however, a third alternative. In recent papers by two of the authors3,4 it was shown that for many materials a significant decrease in cake moisture can be obtained by applying live steam to the cake face during the drying part of the filter cycle. Further, this limited drying appears to have distinct economic advantages compared to thermal drying. It is the purpose of this paper to explore the third alternative. To do this, the results of an extensive pilot study of steam filtration of a hematite flotation concentrate will be critically examined. This study was sufficiently broad so that a number of alternate suggestions (besides steaming the cake) for reducing moisture content were tested, and comparative data for both Drum and Disc filters were obtained. The work was particularly interesting since the concentrate has a high Blaine surface, and is therefore particularly difficult to dewater to the levels required. FILTER CAKE MOISTURE The significant difference between concentrate filter cake as discharged from the filter, a cargo of that same filter cake during or after shipment, and a green ball formed from that filter cake is in the relative volume of voids, or porosity. In every case, the material is a collection of small solid particles held together by the cohesive forces of a liquid. The physical properties of the aggregate are determined by the

Jan 1, 1967

By M. M. Rao, P. G. Winchell

The growth rates of bainitic plates were measured at 400°C in Fe-Ni-C alloys containing 0.10 atom-fract~on nickel and 0.0012 to 0.0075 atonz-fraction carbon. The growth rates are adequately represented by where xc is nearly the atom fraction carbon of the bulk austenite and PXCy is nearly the carbon atom fractlon in the ferrlte of radiids p In equilibrium with austetzite. The form of the equation is that predicted by a model in which carbon diffusion in austernite controls the gvowth, but the numerical constatnt is two orders of magnitude below that suggested by the model. THE growth of bainitic plates in steel is often assumed to be controlled by the diffusion of carbon away from the advancing plate tip. This hypothesis predicts that the growth rate will increase as the carbon content of the austenite, xCz, is reduced toward the carbon content of the saturated ferrite comprising the plate tip, PxCY The growth rate should vary approximately as (xCg- pxCy)-1. Experimental observation of the growth behavior at low carbon levels should provide a significant test of this model. An alloying element in addition to carbon is required so that low-carbon austenite can be experimentally observed while undergoing bainitic transformation. Nickel was selected. The presence of nickel complicates the interpretation of the data in two ways: First, diffusion of nickel during the transformation would make analysis very difficult. Nickel is assumed immobile during the transformation. Second, nickel affects the solubility of carbon in ferrite and austenite in equilibrium. This effect has been evaluated.' At the completion of our experimental work Goode-now et al.2 published data in essential agreement with the observations to be reported here. Since their discussion is abbreviated and their data are scanty in the region of interest, we believe the present work is of significance. I) THE MODEL OF BAINITIC PLATE GROWTH The rate of lengthening of a plate is assumed to be controlled by the diffusion of carbon from the advancing ferrite-austenite interface into the surrounding austenite. The precipitation of carbides is assumed to be a secondary process. For ease of analysis the carbon-atom ratio,* pxCy, of austenite in equilibrium with ferrite which is convex with minimum curvature radius p, and the carbon-atom ratio, PxCY, of that ferrite in equilibrium with austenite are assumed independent of location on the ferrite-austenite interface. Since these carbon contents vary with the radius of curvature of the ferrite, p, their assumed positional independence must be held as an approximation. The consequences of these assumptions have been developed approximately by zener3 and Hillert,4 and the resulting equation for a platelet has been applied to bainite by Speich and cohen5 and Kaufman, Radcliffe, and Cohen.8 The Zener-Hillert equation* for plates is: The analysis of Hillert is supported by that of Hor-vay and cahn7 which involves no mathematical approximations but does include the assumption that the a/y interface coincides with an isoconcentration line. The solutions of Horvay and Cahn for elliptic paraboloids are replotted in Fig. 1. The shape of the paraboloid is expressed in terms of the ratio of the principal radii of curvature at its tip, A =p1/p2, which is also the ratio of the minor to the major axis of the elliptic cross section. The Zener-Hillert equation for plates is also plotted. The agreement is within a factor of two for (pxyaCr - xyC )/(xyC - PxCaY) between 0.5 and 100. This is the range of interest here and in most other work on bainite. The original form of the Zener-Hillert equation was the form given above with the right-hand side replaced by (pxCya -xCy)/(PxCya). This replacement is not appropriate here. 11) THE EXPERIMENTAL PROCEDURE Alloys were prepared and three kinds of experiments carried out. Continuous-cooling-transformation experiments were carried out on wires by measuring temperature and resistance during continuous cooling. Isothermal-transformation experiments were carried out on wires by measuring electrical resistance as a

Jan 1, 1968

By A. Lubinski, J. L. Logan, W. S. Althouse

A4ost gas twells and flowing oil wells are completed and treated through a string of tubing and a packer. Changes in temperature and in pressure inside or outside the tubing will: (I) if free motion of the tubing inside the packer is permitted, increase or decrease the length of the rubing; or (2) if free motion is prevented, induce forces in the tubing and on the packer. If pressure inside the tubing is greater than outside, the tubing may buckle helically even in the presence of a packer-to-tubing tension. The tubing will always buckle, and much more severely, if free motion is permitted. The buckling may be prevented by pulling the tubing in sufficient tension. The prediction of these forces and tubing movement has here to fore been based upon calculations that did not inciude helical buckling. This paper preseitts means with which these length or force changes can be calculated while taking into account the effect of helical buckling. To avoid damaging formations, failure of remedial operations, or damage to the tubing or packer, application is made to practical problems involving calculations of the required length of seals, amount of sluckoff or tension, and prevention of permanent corkscrewing. INTRODUCTION Leakage of a packer may result in costly failures of such operations as squeeze cementing, hydraulic fracturing, etc. To avoid such failures, the authors are often asked questions pertaining to the length of necessary seals, the amount of necessary slackoff, etc. Published work' does not take into account helical buckling of tubing. Investigation of helical buckling was prompted by the fact that allowance must be made for this phenomenon in order to provide relevant answers. In the past, theoretical work on helical buckling was confined to conditions for which such buckling does not The mathematical treatment of behavior in a buckled condition, given in the Appendix, is novel. Assumptions upon which this investigation is based are listed and discussed in a special section. The following are a few of the many kinds of problems which may be solved with this paper. 1. Consider a packer in which tubing may move. Such movement will occur after pressures and temperature are changed. The paper provides means for: (a) calculating the amount of such movement and, therefore. the required length of seals; and (b) calculating the necessary amount of initial slackoff, for which there is no danger of unsealing the packer, if the length of seals is given. Such calculations, as well as those which follow, tully take into account the fact that part of the movement ib due to elastic helical buckling of the lower part of the string. This buckling may occur even in tubing under tension. Insufficient initial slackoff for a given length of seals, or insufficient length of seals for a given slackoff, may result in costly failures. A field case of such a failure will be given further in this paper. 2. In the case in which tubing cannot move in the packer, changes of pressure and temperature result in tubing-to-packer forces and forces in the tubing above the packer, both of which may be calculated. This knowledge is important because, if these forces are too large, the) could damage the packer or the tubing. 3. For wells in which wireline tools are to be run through the tubing, the paper provides means to keep the tubing from buckling, thereby permitting free passage of tools. 4. In deep wells, mainly in the presence of large casing, tubing may become "corkscrewed", i.e., take a permanent helical set. A field case is described further in the text. Using this paper, one may calculate in advance conditions under which permanent corkscrewing would occur, and then take preventive steps. HELICAL BUCKLING Consider a string of tubing, freely suspended in the absence of any fluid inside casing, as shown in Fig. I(a). Now consider an upward force F applied at the lower end of this tubing. This force compresses the string; and if the compression is large enough (which is always the case in actual problems), the lower portion of the string will buckle into a helix, as shown in Fig. 1 (b). The lower end of the tubing is subjected to a compression F. This compression decreases with the distance from the bottom and becomes nil (neither compression nor ten-

By H. J. Ramey

Conventional calculation of total system isothermal compressibility for a system containing a free gas phase involves, among other things, evaluation of the change of oil and gas formation volume factors and the gas in solution with pressure. Preferably, this information should be obtained from laboratory measurements made with particular oils and gases. Often, experimental measurements are not available. In this case, it is necessary to obtain pressure-volume-temperature relationships from general correlations such as those of Standing' for California oils. In order to speed estimates of compressibility, generalized plots have been prepared of the change of both oil formation volume factors and gas in solution, with pressure from Standing's correlations. A generalized plot for estimating the change in the two-phase (oil and gas) formation volume factor with pressure is also presented. Usually, the effect of gas dissolved in reservoir water upon the total system compressibility is neglected for gas saturated systems, due to the low solubility of gas in water. Results of this study indicate that the increase in total system compressibility caused by solution of gas in water is often as large as the compressibility of wafer, and can be magnitudes larger for low pressure systems. Generalized results for estimating the change of gas in solution in water with pressure are presented in tabular and graphical form. INTRODUCTION During the past decade, pressure build-up and drawdown techniques have gained an important place in reservoir engineering. Build-up and drawdown analyses are only two special applications of the broad field of transient fluid-flow theory. All solutions of transient fluid-flow problems contain a parameter called the total system isothermal compressibility. This property of fluids and porous rock is a measure of the change in volume of the fluid content of porous rock with a change in pressure, and it may vary considerably with pressure. Evaluation of total system isothermal compressibility is not difficult, but it is tedious and time-consuming. Often compressibilities are estimated roughly, or transient flow methods are neglected completely. The benefits of using accurate system compressibility in properly-executed build-up or drawdown analyses are: 1. Better planning of pressure build-ups may be achieved to avoid unnecessary loss of revenue due to excessively long shut-in periods, or to shut-in periods too short to yield useable data. 2. Better and more reliable estimates of static formation pressures for reserves estimates and rate performance estimates. 3. Reliable information for evaluation of well completion effectiveness, and planning and interpretation of well stimulation efforts. The purpose of this paper is to clarify the nature of the total system isothermal compressibility, and to present useful methods for estimation of compressibility, particularly for systems containing a gas phase. DEVELOPMENT Numerous publications have presented solutions to transient single-phase flow of slightly compressible fluids, stressing pressure build-up applications. In transient flow, a compressibility* term arises to permit volume content of fluids in porous rock to change as pressure changes. The basic nature of the compressibility term is usually taken for granted. Problems arise in practical applications of transient fluid theory because most published works consider only one flowing fluid—in an ideal porous system containing only one fluid. In 1956, Perrine2 presented an intuitive extension of single-phase flow pressure build-up methods to multiphase flow conditions. Later, Martin- established conditions under which Perrine's multiphase build-up method had a theoretical foundation. Perrine has shown that improper use of single-phase build-up analysis in certain multiphase flow situations can lead to gross errors in estimated static formation pressure, permeability and well condition. It is likely that, much pressure build-up data for oil wells should be analyzed on the basis of multiphase flow. For both single-phase and multiphase build-up analysis, the isothermal compressibility term in dimensionless time groups often should be interpreted as the total system compressibility. All real reservoirs contain one or more compressible fluid phases. In addition, rock compressibility can contribute in an important way to the total system compressibility. The proper total system compressibility expression may contain terms for compressibility of oil, gas, water, reservoir rock and terms for the change of solubility of gas in liquid phases.

Jan 1, 1965

By S. W. Ihle, L. J. Warren

A sample of garnet from the scheelite ore body on King Island, Tasmania, Australia, was upgraded and ground to produce an ultrafine portion suitable for micro-electrophoresis. X-ray and chemical analysis identified the garnet as andradite with some admixed grossular. At neutral pH the garnet particles were negatively charged, their zeta potential becoming rapidly more negative with increasing pH. An iso-electric point was found at pH 3.5. The effects on the zeta-potential of various electrolytes, hydrolyzable metal ions, and flotation collectors were also studied.

Jan 1, 1976

By John M. Tinsley, Calvin D. Saunders, H. K. van Poollen

In the past few years much con-sideration has been given to the evaluation of the effect of hydraulic fracturing on the productivity of wells. Generally, these studies included the evaluation of fracturing materials, fracture extension and formation damage due to the use of various fracturing fluids. Only little consideration has been given to the characteristics, and in particular the flow capacity, of the fracture itself and its effect on well productivity. This paper presents the results of laboratory investigations pointed toward fie evaluation of the efficiency of various fracrures with special emphasis on the flow capacity of these fractures. Data presented in this paper are the results of both an electrical model study and physical testing. Under consideration are (I) effect of overflush, (2) premature production of well after treatment, (3) "tailing-in" with coarse sand near the end of the treatment, (4) effect of propping agent size and concentration, (5) reduction in effective frac-ture permeability caused by formation caused by formation fines, silt and clays, and (6) effect of various fluids on formation strength and competency. The results of this investigation indicate that the flow capacity of a fracture is affected by any or all of the various parameters mentioned above. The authors believe that a better understanding arid utilization of these factors should result in more efficient formation fracturing. INTRODUCTION Hydraulic fracturing has become almost a standard practice of many companies for stimulating production from old and new wells. Although most companies utilize this service, techniques of application vary widely between companies and areas. Probably too often when a well in an area responds favorably to a particular technique all future wells in the same area are treated in a similar manner. Possibly a modification of the technique would result in a further production increase. Variables, of which many are extremely difficult to evaluate from field results, hamper the selection of procedure changes. Attempts are being made by a number of organizations to analyze statistically treating techniques from production data. This is a very worthy and necessary approach but very possibly laboratory investigations may aid in evaluating some of the variables which tend to affect the results of a fracturing treatment. Some of the factors cannot be studied from practical field experience and only laboratory tests can show the possibilities which might exist. One of the factors which appears to be of major concern today is the flow capacity of the created fracture and how it can be changed. Papers on this general subject have been primarily concerned with the size of propping agent and the extent of fracture. Papers have also been written on the possible permeability damage to formations by fracturing fluids. In addition, it might be possible that another type of flow restriction is prevalent. This would be a restriction of flow through a sand-packed frac- ture caused by foreign materials integrating within the propping agent. This paper presents preliminary data obtained in an attempt to evaluate the effect of some factors affecting flow through sand-packed fractures. No attempt is being made to offer a fracturing technique adaptable to all areas and conditions, but to furnish data tending to show the possible effects which might be caused by variations in procedures and materials. PROPPING AGENT PERMEABLLITIES A hydraulically induced fracture containing sand as a propping agent may theoretically be classified as a packed-sand system. The flow of fluids through such packed systems has been the subject of much research. Although there have been numerous methods proposed for the evaluation of such systems, most writers agree on the general properties affecting their flow capacity or permeability. These properties include porosity, particle size, sphericity and the roughness of the particle. In some methods of evaluation . the particle size and sphericity terms are combined to produce an equation which is a function of the surface area of the particles. In this study the permeability of various fracturing sands was both measured and calculated. The apparatus for the permeability measurements consisted of a 52-in. Lucite tube with a 2.5-in. ID. A screen and drain plug were fitted in the bottom of this tube to retain and hold the sand in place while allowing fluid flow. Two pressure taps consisting of thin, highly perforated

By J. E. Warren, J. H. Hartsock

Because of the extensive utilization of hydraulic fracturing for the stimulation of low-productivity wells, the two related problems of fracture design and evaluation have become economically significant and, as a consequence, helve motivated this investigation. The producing characteristics of horizontally fractured wells were studied to determine the fracture configuration that should be employed as the basis for the design of the treatment and to develop a method that can be used to establish the degree to which the design objectives have been achieved. The equations which describe the steady-state flow of a single-phase fluid into, and through. a finite-capacity fracture were solved numerically for an idealized reservoir-fracture model. The numerical results were used to obtain an apparent skin effect for each combination of the parameters considered. Based on the computed results, subject to the limitcitions implied by the assumptions that were made, the following general conclusions were drawn. 1. For a radius of drainage at least four times us large as the radius of the fracture, an apparent skin effect that is independent of the radius of drainage can be calculated. 2. The productivity of the hydraulically fractured system, relative to that of the unfructured well, can be determined from the apparent skin effect and can be used to establish design objectives. 3. In the evaluation of a fracture job, it is not Possible to determine both the radius of the fracture and its flow capacity uniquely from the apparent skin effect; an independent determination of one of the quantities is necessary. lNTRODUCTION Although hydraulic fracturing has been employed as a method for stimulating the productivity of literally hundreds of thousands of wells during the past 10 years, it is only in the last few years that improvements in fracture design1-6 and fracturing technique' have combined to increase the probability of obtaining a successful treatment to such an extent that the mechanics of the method may be considered to be standardized. From an economic point of view, however, two related questions must be satisfactorily answered before hydraulic fracturing can be used in the most profitable manner. The two questions are the following. I. For a particular well in a given formation, what are the optimum design specifications for the fracture treatment? 2. Have the design objectives been achieved by the fracture treatment? The significance of these questions has been recoguized, and some attempts to obtain answers have been made. Howard, et al,8 endeavored to determine the optimum treatment, based on maximizing profits, for any given formation; unfortunately, this work was based on a crude method for approximating the productivity of a well. Carter and Tracy9 utilized the same approximation to study the effect of fracturing on the behavior of a well producing by virtue of a solution-gas drive. Electrolytic models were used by van Poollen10 to investigate the variation in productivity due to fracturing; however, only a limited number of results were presented. Later, from the same model results, van Poollen, et al,11 attempted to justify an approximate expression for determining the productivity of a fractured well. It is quite apparent that there is a definite lack of the practical information necessary for specifying the optimum fracture configuration to be considered for design purposes. The only detailed attempt to develop a procedure for evaluating the result of a given fracture treatment appears to be that of van Dam and Horner.12 These authors described a technique for analyzing pressure build-down data, obtained immediately after fracturing, to determine the final fracture volume, the final fracture porosity, the fracture area, the fracture thickness and the in situ fluid loss of the fracturing fluid. While this approach should be useful whenever acceptable pressure measurements are available, it does not yield a value for the flow capacity of the fracture. Since the problems of fracture design and evaluation are inversely related, it should be sufficient to study the effect of the fracture configuration on the performance of a well. The primary objective of this investigation is to evolve a technique for computing the desired solutions. The secondary objective is to analyze these computed results in order to prescribe a method for evaluating fracture treatments. Because this study is exploratory in nature, its scope

By B. L. Averbach

Recovery and primary recrystalliza-tion in cold worked metals are usually considered as two competing processes. Some of the effects which usually accompany recovery are: alleviation of stress corrosion tendencies, changes in thermal emf,1 damping capacity,2 electrical resistivity,2 and magnetic properties,3 and only minor changes in hardness or the related strength properties. During primary recrystalliza-tion new unstrained grains are formed at the expense of the strained matrix. These new grains eventually become visible metallographically, and nucle-ation and growth kinetics have been indicated for this process.4,5 Frequent attempts have been made to study the cold-working phenomenon by observations on the line broadening by X ray diffraction patterns. Relatively few measurements of line intensities have been made, although Brind-ley and his collaborators, 6,7,8 by means of film techniques, compared the intensities of cold worked Cu, Ni, and Rh patterns with those from chemically precipitated powders. These precipitated powders were presumed to be strain free, and it was found that the intensities for the cold-worked materials progressively decreased as the Bragg angle increased except for the first line, where there was an increase due to reduction in extinction. This was interpreted as a randomness in atomic position induced by cold work. Such randomness is similar to that caused by thermal agitation and has been described as "frozen heat" displacement of 0.08-0.10 A from the mean atomic position. In a recent study9 on the effect of cold work in metals on their powder pattern intensities, the changes in integrated intensity for heavily cold worked alpha brass were observed as a function of the annealing temperature. These measurements were made with a manually operated Geiger-counter spectrometer using CuKa radiation monochromated with a rock salt crystal. Intensity measurements were made with a scaling meter over small intervals of angle, and the equipment was so arranged that the diffracted and incident beams made equal angles with the specimen. Intensities could be compared directly by simply interchanging specimens, and comparisons from day to day were made with a standard whose line intensities did not change on aging. It was shown that a cold worked alpha brass standard was stable for at least a year. Table 1 indicates the results of the integrated intensity measurements on a 70 Cu-30 Zn brass. In the sample preparation, a brass plate was first cold rolled 50 pct and then filed, screened to —325 mesh, compacted into briquettes at a pressure of 60,000 psi and finally annealed for one hour at various temperatures up to 400°C. The briquetting pressure did not seem to influence the integrated intensities, and most of the cold work was introduced by the filing. Although this method of cold work is not quantitative, it was used to obtain random orientation (and thus uniform diffraction lines) in order to make accurate measurements of integrated intensity. Back reflection patterns were taken in each case to check the uniformity of the lines, and from the observed line broadening it was apparent that this type of plastic deformation was quite severe. Care was taken to traverse the entire background of the pattern and to assign to each peak the total intensity above this background. The bases of the diffraction lines were quite broad and spread out over several degrees, even for the narrow peaks. The theoretical intensities were calculated to include a temperature correction, a dispersion correction, and a Lorenz- polarization factor corrected for the crystal monochromated beam. In Table 1 it was necessary to match the calculated and observed values at only one point, and the rest of the experimental values were converted directly to this arbitrary scale. The integrated intensities in Table 1 are listed in arbitrary units, and the accuracy was sufficient to reproduce any of the measured line intensities to within + 1.5 units. It is evident that the percentage error on the strongest line (111) was quite low. The calculated values and the observed intensities for the cold worked material matched reasonably well. As the annealing temperature was raised, however, the intensity of the strongest reflections, particularly the (lll), decreased measurably. Since the background intensities of all of these patterns were identical, such behavior could be interpreted as a primary

Jan 1, 1950

By J. P. Denny

The constitution of the Ga-In system was determined by thermal methods. An experimentally determined metastable equilibrium line (an extension of the indium-rich liquidus) was obtained. The various alloys were studied metallographically using polished samples obtained by a casting method. These low melting alloys required a special dry-ice assembly to maintain a suitable temperature. RECENT interest in alloys that are liquid at room temperature has led to rather extensive investigation of gallium-base alloys. Widely distributed over the earth, gallium could be produced in substantially larger quantities than at present, if a significant demand existed.' One study' has established its presence in 12 out of 14 zinc blends, in all of 15 aluminum ores, in 4 out of 12 manganese ores, in 35 out of 91 iron ores, and in all of 7 magnetite ores. It occurs as a rule in minute amounts, however, leading to high extraction costs. Recent quotations run from $2.50 to $7.50 per g. During the course of the present investigation, portions of the system Ga-In have been redeter-mined, and the results of this study are presented herein. Thermal and metallographic methods have been employed. Lecoq de Boisbaudran, the discoverer of gallium, conducted the first investigation" on Ga-In alloys in 1885. The temperatures of incipient melting, and of completion of melting, were determined at four alloy compositions. In 1936, Hansen' constructed a eutec-tic-type phase diagram for the system Ga-In, based on . work. The existence of a Ga-In compound was regarded as improbable by Hansen, and subsequent investigations are in agreement. French, Saunders, and Ingle3 conducted a more complete study of the system in 1938, using thermal methods. Their phase diagram is a eutectic type, containing a unique concave-upward liquidus. The solid-solution range of gallium in indium was reported as 9.5 pct by weight, and that of indium as less than 1 pct, at the eutectic temperature. The eutectic composition, determined as being bracketed by the compositions showing a true horizontal at the eutectic temperature (16°C), was reported as 76 5-0.5 pct Ga and 24 i 0.5 pct In. Experimental Procedure The preparation of Ga-In alloys is simplified by the low melting points involved. Various compositions were prepared by melting in pyrex tubes, using a cover of distilled water or parafin to prevent the alloys from wetting the glass wall. In all cases, the melts were homogenized. by stirring. Where possible, both cooling and melting curves were determined. The extensive undercooling of gallium was found to prohibit a satisfactory cooling-curve analysis of gallium-rich alloys, however, and transition points on the gallium side of the eutectic could be determined only by melting curves. The inverse rate method of thermal analysis proved to be most satisfactory and was used to a great extent. Various heating and cooling rates were used, ranging from 0.2" to 5.0°C per min. Low temperature melting analyses were conducted within a constant temperature bath, maintained at about 70 °C. The alloys were solidified (under water or paraffin) within a pyrex tube, using dry ice; the tube was then sealed within a cold Dewar flask, the unit transferred into the constant temperature bath, and periodic temperature readings taken. The high temperature melting-curve determinations and all cooling-curve determinations were made in a vertical tube furnace. At near-eutectic compositions, the furnace was placed within a refrigerated room held at —20°C. Accordingly, the furnace on cooling approached —20°C asymptotically and permitted the determination of those phase transitions occurring below room temperatures. Temperatures were measured with a 30-gage iron-constantan thermocouple, immersed directly in the alloy. To prevent contamination of the melt, the leads and junction were coated with Lucite, applied by painting with a solution of Lucite in ethylene dichloride. Electromotive force measurements were made with a Leeds and Northrup precision potentiometer, type 8662. The couples were calibrated against the boiling point. of water and, at lower temperatures, against a calorimeter thermometer having a Bureau of Standards certificate. The melting points of gallium and indium used in the present investigation were determined as 29.-77° and 156.1°C, in good agreement with previously reported values of 29.78°C° and 156.4"C.' The spec-

Jan 1, 1953

By Michael P. Robinson

It has been suggested that streaming potentials are not nomlally logged because the streaming potentials known to be generated across mud filter cakes are substantially cancelled by streaming potentials generated in contiguous shale beds. Laboratory measuments of streaming poterztials acrons hand specirnens of shale have been adduced as evidence to support the suggestion. The experiments show that streanzing potential depends on the resistivity of the equilibrating solution and on pressure drop. Meizsurenlents were made perpendicular to the bedding planes of the shales. The mechanism of streaming potential generation in shale which the suggested cancellation theory iniplies has been critically examined. Conclusions reached are tested by comparing self potentials logged before and immediately after changing the resistil~ity (but not the weight) of mud in a borehole. The resultant SP change is found to equal the theoretical electrochetnical potential change, i.e., cancellation of .strearning potential is independent of mud resistivity. Since streaming po/entials generateal across mud filter cakes depend critically upon mud reistivity, shale .strearlling potential in situ must he equally sensitive. Using plausible values for the pemleahility, porosiy arzd compressibility of shale, the van Ererdingerl-Hurst approach shows that the pressure drop between horehole pressure and formation pressure in a radially honzogeneous shale is unlikely to coincide with the zone of filtrate invasion. If, perchance. this coincidence occurs with one mud a chatzge 10 a second must result in non-coincidence, i.e., a .YP logged in the second mud should show a streaming potenlial. The dilernrna may he overcome by postrrlating: (I) perrneabilities of shale7 parallel to their beddine planes greatly exceed their cross-bedding permeabilities; (2) a resistivity-sensitive mud cake of low permeability forms either on the face of, or probnhly in the lanlinations of, many shales. These postulates are examined with reference to the pres.sure and SP histories of the McClosky and Aux Vases zones in the Illinois Basin and some srcpport for them found. It is concluded that a definitive solultion to the streaming potential problem does not exist. INTRODUCTION Recently Gondouin and Scala' published a contribution to the streaming potential problem which is notable particularly for the elegance of its experimental techniques. The conclusions drawn by Gondouin and Scala from their studies amplified those previously suggested by Schehck'. In essence they suggested that the streaming potentials known to develop across mud filter cakes" are not normally observed on SP logs because they are largely cancelled by streaming potentials generated in adjacent shales. This suggestion appears so reasonable that many workers in the logging field will be prone to accept it. We incline strongly to the view that the suggestion is basically correct. Nevertheless, it is important to realize that the cancellation hypothesis in the form put forward by Gondouin and Scala does not appear to meet all the known experimental facts. It is the principal intention of this note to call attention to what appears to be a flaw in the relevancy of the experimental evidence adduced by Gondouin and Scala and to suggest an alternative hypothesis to remove it. The consequences of the new hypothesis are compared with field data which, we believe, are unique. A second but not less important purpose of this note is to emphasize that even the new hypothesis does not fully explain all field observations. Hence we conclude that further study of the streaming potential problem is required before it can be said that a definitive solution to it has been attained. The bare experimental bones of laboratory data on streaming potentials appear to be as follows. 1. A streaming potential is developed across a mud filter cake. This streaming potential is virtually independent of cake thickness but depends on the mud resistivity. The relationship is of the form, 2. A streaming potential is developed across a shale. This potential is independent of shale thickness but depends on the resistivity of the permeating solution if the shale has been first equilibrated in this solution. The relationship is of the form, The relationship in (1) was determined first by Wyllie3, confirmed by Gondouin and Scala and qualita-