Search Documents

THE paper on "Cross-cuts in Coal Mining," by J. J. Rutledge (published in MINING AND METAL-LURGY, February, 1927, p. 64) was brought up for discussion at the annual meeting, where the follow-ing comments were made T. D. Thomas (Lehigh Coal & Navigation Co., Lansford, Pa.) : This question has caused me a lot of worry, not in the particular district in which I am, but throughout other districts. There are always several angles to consider. If you are in a hurry to push development work, you might increase the distance between cross-cuts from 60 to 350 ft., but if you have a 40-ft. chain pillar every 60 ft. it will cut down your entry driving a whole lot. Looking at it from the ventilation angle, I agree that too many cross-cuts in entries are bad things. You have a tremendous amount of leakage, and I have seen currents starting out with 45,000 cu. ft., and after passing about 30 or 40 cross-cuts the current has dwindled down to about 18,000 or 15;000 cu. ft. The result is that the question of putting in auxiliary fans is raised. That involves several points into which I do not want to go too far, but I am in favor of not getting in too many cross-cuts, putting them in only where they are necessary: I think the state mining laws are wrong in a number of places on that, and that when you finish with a cross-cut it should be in the room. It should be well sealed on an entry. There are several ways of tightening up the cross-cuts so as not to have the great amount of leakage and wastage of: air that we now have. 'I prefer tile stopping; other people prefer cement or brick, but there is a big fac-tor to all mines, saving the mine. I checked up on the number of fans in the anthracite region and found there are 651. That was derived from the state report of 1921, and it enabled me to compute from the power the weight of the air. In the anthracite region of Pennsylvania we put in 9 tons of air to every ton of coal we get out. Tracing that back again and taking the Government's figures which they made some time ago, I found but 20 per cent of the air got to the faces where it was actually needed. That is a tremendous big loss and shows a possibility for saving, money for the various coal companies. Chairman Rice: I think what Mr. Thomas refers to was an investigation by R. Y. Williams, of the Bureau of Mines in Illinois, where a study was made of 100 typical mines, and, speaking off-hand, my recollection is that we found as little as 15 per cent of air reached the faces in one of the mines and another was as much as 50. That seems to be a reflection on the type of stoppings and general ventilation scheme.

Jan 3, 1927

By L. C. Brown, J. S. Kirkaldy

AS part of a program to investigate the diffusive properties of dilute ternary austenites, we have made a determination of the effects of cobalt on the activity of carbon in y iron. Samples of pure iron and Fe-Co alloys were equilibrated at 1000°C in controlled CO-C02 atmospheres, following the procedure of R. P. smith.' The 0.010-in.-thick samples were analyzed for carbon by microcombustion analysis2 to give a set of isoactivity curves. The latter were converted to activity-coefficient (standard state at infinite dilution) plots by combination with Smith's data' for the activity of carbon in pure iron measured in a CO-C02 mixture. Table I shows the composition of the base alloys used, while Fig. 1 shows the experimental results superimposed on a set of curves generated by the relation In the notation of Wagner,' the interaction parameter is the second coefficient on the right, Eq. [I] adequately correlates the experimental points for those alloys which were prepared from electrolytic iron by arc-melting (2,4, and 7 pct Co). The results for the 10 pct Co alloy (supplied by Crucible Steel Co.) do not correlate with the others. In fact, the experimental points for this alloy correspond to an interaction parameter of It is possible that the interaction parameter is a function of concentration for large cobalt additions, but we are inclined to attribute the discrepancy to the presence of a significant amount of aluminum added to this alloy for deoxidation purposes (Table I). Preliminary measurements for the system Fe-C-A1 have indicated an interaction parameter of Which implies that the effect of aluminum in solution on the carbon activity is sixty times greater than the effect of an equal weight percentage of cobalt. These observations cast some doubt on the precision of the results of Chandhok, Hirth, and Dulis who used this same 10 pct alloy for their experiments, obtaining an interaction parameter of E = 2.2. There is considerable doubt as to the activity of a plane Fe-C system. Using a CH4-Ha mixture, Smith obtains cg = 6.1 for the effect of carbon on the activity of carbon in austenite, rather than the value of 8.9 given in Eq. [I]. The use of CHa-Ha mixtures has recently been questioned by Kaufman, Radcliff, and cohens who state that there is some possibility that other hydrocarbons are formed. Fortunately, the determination of the interaction parameter is not sensitive to the coefficient of Nc. For example, using the CHI-H2 results we obtain a value which is almost the same as that obtained using the CO-CO, results. The authors wish to thank Mr. E. J. Dulis of the Crucible Steel Co. of America for supplying us with samples of the 10 pct Co alloy used in their original work. Financial assistance from the American Iron and Steel Institute is gratefully acknowledged.

Jan 1, 1963

By Philip D. Anderson, Ralph Hultgren

Heat contents of extremely pure iron were measured over the range 300"to 1433"K, using a diphenyl ether calorimeter. Results from three samples containing widely differing impurities agreed with one another and with Previously reported results at higher temperatures (1184 ° to 1809°K) by Olette and Ferrier. From these data a table of heat contents of iron has been Prepared which is believed to be more accurate than those previously available. CP values have been derived which are consistent with these heat contents, with the best experimental Cp data, and with the thermodynamic conditions of equilibrium between bcc and fcc iron. The opinion is expressed that low-temperature extrapolations of presently known Cp values for y-Fe are not reliable. It would seem that the thermodynamic properties of iron, which is by far our most important metal, should have been well established long ago. This is not the case, however. As discussed by Olette and Ferrier,' there is objection to every earlier heat content measurement. While the best true Cp determinations agree well at temperatures below the Curie point, there is wide divergence at higher temperatures. Several investigators have examined available data and attempted to calculate thermodynamic functions for iron that are consistent with the two equilibrium temperatures of bcc and fcc iron. The two primary efforts were those of Austin' in 1930 and Darken and smith3 in 1948. The recommended values differ considerably; integration of Austin's Cp values leads to a heat content at 1100°K which is 300 cal per g-atom higher than the value recommended by Darken and Smith. The compilation of Fisher4 in 1949 was based on the selection of Austin. In 1956, Weiss and Tauer obtained yet another set of values by resolving Cp values into components due to dilation, lattice vibration, electronic excitation, and magnetism. The magnitude of contribution by each component and its dependence on temperature was estimated by semiempirical means. Their values are not self-consistent in that they do not form smooth curves when plotted vs temperature; moreover, their calculations cannot easily be repeated since they do not give the values of some of the parameters used. Clearly, experimental values for iron were in a most unsatisfactory state. The presently described measurements of the heat content of iron were therefore undertaken, covering temperatures as high as 1433°K. While the work was in progress, the high-temperature (1193" to 1789"K) heat content measurements of Olette and Ferrier' were published; in the region of temperature overlap the present results agree with Olette and Ferrier well within experimental accuracy. It is believed that the present results, combined with those of Olette and Ferrier, provide for the first time a reliable set of heat contents of iron from room temperature to the melting point. From these data, guided by available Cp measurements, it proved possible to derive Cp, entropy, and free energy function values for @-iron from room temperature to the melting point, and for y- iron in the temperature region of its stability. Exhaustive study led to the conclusion that extrapolations of y-iron functions to room temperature were not reliable enough to be useful; hence these have been omitted from the tables. EXPERIMENTAL Materials. Three samples of extremely high purity iron from different sources, containing widely different impurities, were measured. The first of these, designated "Chipman", was kindly supplied by Dr. K. K. Kelley of the U. S. Bureau of Mines from a lot which was made many years ago by Dr. John Chipman of the Massachusetts Institute of Technology. The second, designated6'Teddington", was supplied by the National Physical Laboratory, Teddington, England, from a lot zone-refined by them. The third sample, designated "Irsid", was supplied by the Institute de Recherches de la

Jan 1, 1962

By C. E. Lawall

ONE of the most important developments in the coal industry during 1940 was the continued uptrend in the production of bituminous coal. Estimated production for the year is 450,000,000 tons, with an additional production of anthracite of 50,000,000 tons making a total of approximately 500,000,000 tons. This is an increase of 12.5 per cent over 1939. Despite an estimated decrease of about 3.5 per cent in anthracite production, all of the major coal-producing states had increases in production for 9140. The national defense program, with the consequent increase in industrial activity, undoubtedly had an important effect on the increased demand for coal.

Jan 1, 1941

By P. A. Young

The historical background of on-strand cooling is given, together with a resume of recent practical developments. Laboratory test procedures are then considered in detail, for both productivity and quality parameters, with particular reference to the design of the Ravenscraig No 3 machine (Scotland). A heat transfer model is presented for a porous sinter with propagating cracks. The influence of cooling/sintering area ratio, sinter strength, granulometry, return fines, coke consumption and FeO levels are examined in relation to economics. A detailed comparison of capital and running costs for two different strands, designed for identical duties, but with off or on-strand cooling, is then given.

Jan 1, 1977

By W. N. Marchant, P. T. Brooks, P. B. Altringer, R. O. Dannenberg

The US Department of the Interior, Bureau of Mines conducted laboratory tests to devise a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 ppm W (70ppm WO3). Using ion exchange resins synthesized by USBM chemists, 98% of the tungsten was extracted from the brine and 92% of the tungsten was recovered as a marketable iron-tungsten concentrate containing 44% tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process research unit to provide more reliable data for an economic appraisal

Jan 1, 1980

US 4,183,794 - Electrowinning zinc from a zinc sulfate solution produced by leaching zinc ore with sulfuric acid. The leach liquor is subjected to electrolysis in a first cell having an insoluble anode to deposit primary zinc on the common electrode. The coated electrode is transferred to a second cell having an alkaline electrolyte, and electrolysis is effected in the second cell to transfer zinc from the common electrode to the second cell cathode in a spongelike form which is readily stripped. R.H.C.L. Ross. Jan 15, 1980. 10 pp. (204-119). Filed: 12-22-77 (863,190). Same: Canadian 1,051,820, dated Apr. 3, 1979.

Jan 1, 1982

By Marsh S. Watson, Robert A. Howard

An electrolytic model study has been made of the relative productivity of perforated casing. The results show that the relative productivity is roughly one-half to two-thirds of that predicted from point-sink calculations. This discrepancy can he satisfactorily explained on the basis of casing interference. The relative productivity was found to he insensitive to spatial arrangement of the perforations. INTRODUCTION The relative productivity of wells with perforated casing has been treated mathematically by Muskat.' In his treatment the perforations are represented by small spheres, thus enabling him to approximate the flow by that to point sinks. By neglecting interference between the flow into the various spheres representing the perforations, one may deduce the approximate formula Qu 1/rp - 1/rw • (1) I + b/2n _________ 2n In re/rw Where Q is the flow rate into spherical sinks located in the median plane of the sand laver Qo is the open hole flow rate (uncased hole of radius rw) b is the thickness of sand layer under consideration (always one foot in this paper) n is the number of spherical sinks in the sand layer rp is the radius of a spherical sink rw is the well radius re is the drainage radius of the well. Fig. 1 is a comparison of values calculated from equation (1) with Mus-kat's values. It will be observed that the approximate values are in error by less than 21/2 per cent. The disturbing effect of the casing on the flow line; is not explicitly taken into account by Muskat, but he reasons that interference between the flow pat- terns from the various point sinks will result in a negligible flow in the region within the well radius, and that no appreciable error will result from not explicitly excluding flow from this region. This line of reasoning is open to question, however, as the flow impedance, in the immediate vicinity of the well, of a hemispherical cavity in contact with an opening in the casing is twice that of a spherical sink in a continuous sand layer. There will be a difference, moveover, between the flow into a hemispherical cavity and that into a circular hole in the casing. .This latter difference can best be appreciated by comparing the flow from a semi-infinite medium into a hemispherical cavity at the edge of the medium with the flow out of a circular opening of the same radius as the hemisphere and which is also on the edge of the medium. In this case2 ------= —2, showing that the difference in flow rates into differently shaped cavities is quite appreciable. It was the purpose of the investigation reported here to determine to what extent flow into circular perforations in casing departs from the values calculated by Muskat. For this purpose an electrolytic model was used.

Jan 1, 1950

By Oliver Bowles

WHEN a new type of equipment revolutionizes methods of quarrying one kind of stone, producers of other kinds focus their attention on its potentialities in their particular fields. The purpose of this paper is to discuss the accomplishments of the wire saw in slate, to show its more limited attainments in other kinds of stone, and to point out the possibili-ties of much wider application. A wire saw consists of a 3/16-in. or 1/4-in. three-strand wire cable that runs as a belt and cuts the rock by abrasion. (Fig. 1.) The teeth of the saw are sand grains carried in the grooves between the strands.

Jan 1, 1936

By B. C. Craft

Oil and gas development in Arkansas during the year 1933 has been marked by considerable wildcat drilling, considering the overproduction prevalent in the oil industry. Arkansas showed an increase in drilling operations during 1933. There were 45 completions from 10 counties resulting in 7 oil wells and 38 dry holes, compared with 37 completions resulting in 4 oil wells and 33 dry holes during 1932. Miller County continued to be the most active area, with 18 completions resulting in 3 oil wells and 15 dry holes. Extensive exploration around the Miller County field has more definitely established the producing limits. It has confirmed the belief that produc-

Jan 1, 1934

By J. W. Downey, A. E. Dwight, R. A. Conner

In a previous paper' we have reported the existence of a number of AB2 Laves phases in which A is a member of the scandium group (including the 1an-

Jan 1, 1967

By W. A. Dickinson, H. F. Hendershot

THIS paper is a brief discussion of the past and present methods employed by the Huntington Works of The International Nickel Co., Inc., in the production of nickel and high nickel alloy seamless tubing. The various operations for both hot and cold processing will be considered in their natural sequence, together with the processing characteristics of the high nickel alloys and some descriptions of the equipment used. The tools and lubricants currently in use will be described. This discussion will relate primarily to nickel, Monel,† and Inconel,† since these are the most common of the many alloys processed into tubing at the Huntington Works. The nominal compositions of the materials are shown in Table I. CONVERSION FROM SOLID BILLETS TO TUBE SHELLS History The commercial production of seamless nickel and high nickel alloy tube shells is a comparatively recent development, the first nickel shells having been produced in 1922, Monel in 1930, and Inconel in 1931 on rotary-type piercing mills. Rolled or forged billets, ranging from 3 ½ - to 7 ½ in. diam, were pierced to produce shells ranging' in size from 4 3/8 in. OD X 0.180 in. wall to 8 3/8 in. OD X 1.0 in. wall. After piercing, the shells. were further processed by hot rolling, reeling, and sizing. Subsequent to these operations the shells were either supplied to the trade as "hot finished" tubes, or were processed by cold drawing to smaller sizes at the Huntington Works of the International Nickel Co. The extrusion of nickel and high nickel alloys also may be classed as a relative newcomer to the field of hot-forming methods, for it was not until 1928 that the commercial extrusion of these alloys was begun on a 600 long ton vertical extrusion press installed at Zenith Works of Henry Wiggin and Co., Ltd., Glasgow, Scotland. This press did considerable pioneer work and the results were so favorable that in 1937 a -2200 long ton horizontal press was installed. The quality of the inside surface of the tubing produced on this press was superior to that produced by piercing on a rotary-type mill and, as a result of this experience, a 4000 ton horizontal extrusion press was installed at the Huntington Works in 1943. Billet Preparation The first step in the extrusion, process is the selection of ingots with good hot malleability, as indicated by the test described by Martin and Bieber.1 Ingots then are forged into rough rounds which are machined to the desired billet diameter on a "bar peeler." This machine consists of a rotary head which carries the cutting tools and is driven by a 200 hp, dc motor. The feed mechanism consists of hydraulically driven input and output carriages on the respective sides of the cutter head. The diameter of the forgings used and the machined size or "billet diameter" that corresponds to the four different sizes of

Jan 1, 1951

By A. J. Carlson, G. M. Marincel, M. L. Hovland, J. H. Healy

Research personnel of Erie Mining Co., a pioneer taconite mining firm on the Mesabi Range, have invented a new method to make an effective 325 mesh separation at high tonnage rates over stationary screens. The company regards this development as historically significant in that it represents the first successful method to commercially screen large tonnages of ore at fine sizes. Erie, which is now completing an expansion program at its plant site near Hoyt Lakes, Minn., has incorporated this screening method as part of that expansion. When completed, the concentration plant will produce 10.3 million tons of iron concentrate, all of which will have been efficiently screened at 325 mesh.

Jan 4, 1967

In accordance with the provision of the Constitution, notice is here given to all Members, Associates and Junior Members, that the dues of the year 1917 will be payable on Jan. 1, 1917, at the office of the Secretary. The dues for Members and Associates are $12 per year and the sum of $3 additional is asked of those Members and Associates who desire to have the three volumes bound in the Institute's standard half morocco binding. The dues of Junior Members are $5 per year. Volume 54 of the Transactions is now printed, and will he sent in January to all members whose dues for the year 1917 are paid.

Jan 12, 1916

By Roshan B. Bhappu, Raul A. Deju

The mineral olivine has been the subject of continued research by various authors. Paik1 conducted infrared and flotation studies of the adsorption of sodium alkyl benzene sulfonates on olivine. These studies are of interest from two points of view. First, in the metallurgical field it is of interest to understand the mechanism of silicate flotation using sulfonate collectors and second, hydrologists are interested in studying the chemical reactions that take place when water plus sulfonates encounter a porous silicate medium. On the basis of his study, Paik was able to postulate a possible mechanism for the attachment of RSO3- (sulfonate radical) to the olivine surface.

Jan 1, 1973

By M. J. deBastiani, John Kostuik

The Denison orebody, located on the north limb of a syncline, rests at depths of 800 ft in the northern end of the property to 3000 ft at the southern end, and has a composite dip of 19º, varying locally from 0º to 45º. It is composed essentially of two pyritized conglomerate beds separated by a varying thickness of quartzite. The thickness of the upper conglomerate reef of the main ore zone varies from 2 to 15 ft while the lower reef is from 2 to 12 ft. Mining, whether carried out over the entire section of the reefs and quartzite or by selective mining of the reefs, is accomplished by room and pillar methods, with an initial 67% extraction on the advance towards the property boundaries. The underground ore handling requirement in such an orebody has become one of the most challenging problems in mining.

Jan 8, 1966

By I. E. Rosenzweig

THE problem considered in this paper is as follows: An arbitrary horizontally stratified area is given. The electrical properties of this area are characterized by a function p(z) (Fig. 1), which shows the relationship between resistivity p of thes oil and the depth z. For such general case the apparent resistivity p* will be computed, by FIG. 1.-GRAPH OF FUNCTION p(z) FIG. 2.-GRAPH OF p(Z) FOR n HOMO-GENEOUS LAYERS. earth-resistivity measurements carried out by any given configuration of electrodes. General solutions of this problem appear to be very important for interpretation of field results of resistivity measurements, concerning structural investigations. Such solutions have been given by many authors for the special case of a finite number of homogeneous layers (Fig. 2)1-4 as well as for the more general case of continuously rang-ing resistivities. 5-8

Jan 1, 1939

By G. H. Jardine

In future years, decision makers in the coal industry will make more and more decisions based on information from computer-based models. Whilst the use of such techniques will provide many advantages for coal companies, particularly in terms of efficient utilisation of their human resources, it is equally important for the decision makers to have an awareness of the limitations inherent in each particular computer-based model being used to provide information for the decision making process. A recommended procedure for identifying such limitations - by analysing the 3 major elements of the model - is presented. The human aspects of increased use of computer-based techniques are emphasised throughout the paper.

Jan 1, 1983

By Murray F. Hawkins, Marion L. Kimmel

sage' appears to have been the first (1933) to design a rolling ball viscosimeter for the express purpose of measuring the viscosity of oils with natural gas in solution, i.e., under reservoir conditions. In 1940 Hocott and Buckley' further refined the rolling ball instrument in both design and method of operation, and their instrument, known as the Humble type, was the forerunner of present day viscosimeters used in petroleum production and research laboratories. They also initiated the technique of charging the viscosimeter with a sample directly from a bottom hole sampler. In 1948 the committee on engineering research 01 the Petroleum Division of the AIME in Part 3 (1) of

Jan 1, 1955

By Frank J. Windolph

Grinding Practice-These tests were run in the 9 ft diam by 8 ft long grate discharge ball mills at Climax. Each mill functions in closed circuit with a 78 in. Akins duplex high-weir classifier, and a circulating load of 300 pct is maintained. The size of the mill feed is 6 pct on 3/8ths, which is ground to pass 28 mesh. Testing Methods-Each grinding section is equipped with a conveyor scale on the ball mill feeder belt, a watt-hour meter on the ball mill motor, and an automatic sampler for the ground product. These instruments are exceptionally valuable to the mill testing program.

Aug 1, 1956