Search Documents

By H. S. Price, D. A. T. Donohue

The system of equations describing displacement of a hydrocarbon liquid by a hydrocarbon vapor in a porous medium where mass transfer takes place between the phases is solved numerically for a variety of gas injection processes. Even though the method of solution is quite general, only systems with three hydrocarbon components are considered. Computer simulations of displacement processes wherein mass transfer between phases is both considered and neglected are compared, and it is shown that neglecting mass transfer can give pessimistic displacement efficiencies. INTRODUCTION The role of the gas displacement process in the recovery of petroleum has been subjected to a series of detailed analyses; as a result, a number of predictive models have been published in the literature. However, because of major simplifying assumptions, most of these models do not completely represent the physical system. As a result, the effect of making the simplifying assumptions is unknown. Therefore, a complete representation of this process — one without major simplifying assumptions —should lead to a fuller understanding of the process, and perhaps to methods of improving it. The general method of developing a model for two-phase fluid flow in a porous medium is to solve simultaneously the continuity equation, the energy equations and the equation-of-state for each phase under the prescribed initial and boundary conditions. For an isothermal system, the energy equations reduce to the momentum equation. Darcy's law. However, since natural gas is the vapor state of the reservoir liquid, interphase mass transfer may take place with concomitant changes in both the intensive and extensive thermodynamic properties of each phase. It is this phenomenon that has often been omitted in previous mathematical models. An additional relation, then, which accounts for mass transfer between the phases, must be included with the other equations to specify a complete model. Completely formulating the equations to be solved is not a difficult task1 but obtaining their solution has been intractable up to now. Availability of large-memory, high-speed digital computers now makes an attack on this formidable problem possible. This paper presents a preliminary study of the problem. Since this investigation is intended to be exploratory, it is restricted to the linear, horizontal, isothermal, two-phase viscous flow of oil and gas in an oil reservoir. In the early development of predictive models of this process, the reservoir system was considered as a unit and various forms of the material balance equation were proposed.2-4 Pressure and saturation gradients were then added in the Buckley-Leverett model.5 The Buckley-Leverett formulation considered the fluids to be incompressible; thus, the mathematical model reduces to a steady-state system. In the 1950's, studies incorporating numerical techniques were being published.6-9 These mathematical models differed in the efficiency of finite difference techniques, the inclusion or exclusion of capillarity or the number of space dimensions considered. To solve these nonlinear, partial differential equations, each phase was considered to be homogeneous with time; therefore, mass transfer between phases was neglected. The effect of mass transfer on the gas displacement process was first reported by Attra. 10 He simulated the one-dimension flow system by a series of cells in each of which the fluids were equilibrated during a time step. In addition, the pressure throughout the system during each time step was predetermined and constant-phase velocities were calculated according to the Buckley-Leverett incompressible fluid flow model. Welge et al.11 developed a model for the displacement of oil by an enriched gas where composition is considered to be a dependent variable. Fluid

By L. R. Page, J. J. Norton

EFFECTIVE methods for determining grade and reserves of pegmatites in advance of mining have been developed in recent years. When intensive work began on the economic geology of pegmatites during the early years of World War 11, it was widely believed that grade and reserves could be estimated only in a most general way. The literature indicated that not all pegmatite deposits are unpredictable, but statements emphasizing unpredictability and irregularity seem to have been more widely accepted. Many standard references reflect the prevailing opinion that minerals: are unsystematic in their occurrence in pegmatites. Pegmatites have been described as "notorious for their irregular structure," and minerals within pegmatites as "irregularly distributed." "irregularly disseminated," of "erratic occurrence," "proverbially erratic in distribution," "characterized by extreme irregularity in ... size and distribution of the essential minerals, and variety and proportion of the accessory minerals," and "spotty.'"" Over many years, however, geologic techniques have been applied with increasing success to economic analysis of pegmatites. Investigations, chiefly since 1939, have shown that mineral distribution and structure of pegmatites are largely systematic and that detailed geologic study can be used to predict the size and shape of mineral deposits in pegmatites. Because the writers are most familiar with the pegmatites of the Black Hills, S. D., examples cited are from that area." Pegmatites mined in other dis- * All examples are described more cornpletely elsewhere.: tricts are similar to those in the Black Hills," and the techniques described here have been applied by geologists and engineers working in other districts. In actual practice few pegmatite mine operators attempt to make accurate estimates of grade and reserves in advance of mining. Many deposits are too small for mining except on a very small scale; few pegmatite mines have more than ten employes. Hence there is little systematic preparation for mining, and the capital outlay may be so small that only a general knowledge of reserves is necessary. Technical personnel are rarely employed by pegmatite mine operators to make such estimates. In the future, however, as capital outlay becomes larger, estimates of grade and reserves will have to be more accurate. Geologic Aspects of Determining Grade and Reserves Estimating grade and reserves requires that the type of pegmatite, the size and shape, and the internal structure be determined by detailed geologic mapping and careful mineralogic study. The wide variations in the texture and distribution of minerals within many pegmatite deposits make a thorough geologic study of this kind necessary before it is possible to decide what sampling methods should be used to determine mineral content or grade. Types of Pegmatites: The first step in economic appraisal of a pegmatite is to determine the min-eralogical and structural type. In general, pegmatites may be classified into two groups: 1) those in which component minerals are more or less evenly distributed throughout the entire body and show relatively minor variations in texture, and 2) those in which component minerals have been segregated into units with recognizable differences in texture, mineralogy. or both. Johnston" has classified these types of pegmatites as homogeneous and heterogeneous, respectively. Cameron et al.10 have used the terms ~inzoned and zoned for similar types. The difference between the homogeneous and heterogeneous types is of great commercial importance. Homogeneous pegmatites can seldom be mined where the products are concentrated by the hand methods now commonly used, but they have been mined in a few places where a milling process has

Jan 1, 1957

By A. D. Bryant

APPROXIMATELY 2 1/2 million tons of silica sand and ground silica with a value of $7.25 million is produced annually from the Ottawa, Illinois, district. These silica products come from the well known St. Peter sandstone formation which covers part of the Mississippi Basin extending from St. Paul on the north to the central part of Arkansas on the south and from Muncie, Ind., on the east to Kansas City on the west. Practically the whole state of Illinois is underlain by this formation except where removed by erosion. Sand produced from the St. Peter sandstone in the Ottawa district is noted for its purity, uniformity, and quality. In addition to various screened grades for industry about 10 pct of the total production of the Ottawa district is ground into silica flour for use in glass, abrasives, enamel, porcelain, tile, for foundry and filter sand, and other uses.

Jan 3, 1953

By F. P. Nichols, F. A. Renninger

At one time, mineral aggregates were considered physically and chemically inert substances whose junction was that of an inex-pensive, easily obtainable source of bulk. This philosophy applied regardless of the use to which the aggregate was put. Research approaches dealing only with such gross physical properties as hardness, toughness, impact resistance, etc., dominated the early growth years of the industry and influenced specifications to a large extent. The accelerated pace of highway construction, which began toward the end of the depression years, focused attention on the need for extensive aggregate research. The realization in the early 1940's that aggregates interacted chemically as well as physically with their environment provided the stimulus necessary to translate the drab, systematic aggregate technology of the early 20th century into the changing, dynamic, challenging field it is today. Current research problems are discussed in detail. These efforts being pursued by contract research organizations, universities, governmental agencies, and industry transcend many fields. The mineral aggregate industry is the world's largest mining and processing endeavor, yet it is graced with little of the romance or public awareness that accompanies mention of gold, silver, iron, copper, uranium, or aluminum mining efforts. Much of this reaction is undoubtedly due to the fact that the uses to which crushed stone and sand and gravel are normally put are not fully recognized or appreciated by the general public. Almost 2 billion tons of mineral aggregates are quarried or mined, processed, and sold yearly in the United States alone.= The largest uses to which this vast tonnage is subjected are as ingredients of portland-cement concrete, bituminous concrete, and dense-graded aggregate-base course mixtures in the highway and building construction fields, two industries closely related to the expenditure of public funds. It is for these uses, partially in justification for the expenditures of vast sums of public funds, that mineral aggregate research truly finds its emphasis. The research efforts expended relative to the highway and building construction uses to which mineral aggregates are subjected are those of primary concern to the industry. These efforts, while of direct consequence to the industry due to the volume market represented, are of interest as well to public agencies, universities, and contract research firms. All actively conduct research, exchange information, and make contributions to the overall knowledge relative to aggregate usage and limitations. The research efforts of the mineral aggregate industry is the subject to be discussed throughout this paper. It covers all aspects of highway and building design, construction, and technology. The effects of research pertaining to quarrying and mining methods, blasting and processing techniques, storage and handling facilities, and equipment employment and development have left their mark on the crushed stone and sand and gravel industries. Such specialized efforts have resulted in dramatically increased production rates which in turn have served to keep costs, and hence prices, down. Despite the many inflationary pressures over the years, the cost of a ton of aggregate today is little more than it was 25 or 30 years ago. Mention is made of these efforts simply to emphasize the diversity of research in the mineral aggregate field. The remainder of this paper focuses on the complexity of what might be termed "product knowledge" research.

Jan 1, 1971

OFFICIAL INSTITUTE REPORTS FOR THE YEAR 1924 Report of the Secretary TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -To a Board of Directors keeping in as close touch with all of the affairs under their care as do the Directors of the A -I M. E, through their monthly meetings, a report of the year's progress is almost superfluous To the members who read the monthly reports of the Board Meetings and of the various activities of the Institute as published each month, a yearly report cannot carry much fresh infor¬mation, yet for both it may be well, as is the custom, to glance over the field of our activities during the past year, and to make an estimate for the year to come The beginning of 1924 was not propitious for the members of the mining profession, though tonnage, production for 1923 had been high and the gross value higher than for several years The margin of profit had been narrow, prospecting and development were limited, and many of our members were unemployed or were working in other industries Toward the end of the year, higher metal prices were in sight Old-time optimism began to grow, and it now brightens the outlook for 1925 An excellent barometer of the prosperity of the industry, and that of the Institute, for they go hand in hand, is the work of our Employment Bureau During the past few months, the percentage of our members for whom openings have been found has been increasing to a marked extent, and many members who had fallen in arrears are placing themselves in good standing The number of new members joining has remained about as it was in 1922 and 1923 The Directors have reason to congratulate themselves on the interest maintained during a dull period, for it is not humanly possible to take a keen interest in the technology of an industry when our hands and minds are not actively engaged in it Now, with a much brighter outlook, we can look forward to a year of increasing prosperity for the industry and for the Institute

Jan 1, 1923

Discussion of the paper of R. H: Sweetser,. presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912 pp. 1327 to 1334. See also Bulletin 11 No. 72, December, 1912, pp. 1561, 1562. J. J. HOWARD, Dover, N. J. (communication to the Secretary*) :-No doubt there are as many different methods of starting a blast-furnace as there are men who assume that responsibility. Having blown-in a furnace a few years ago in a manner similar to that outlined by Mr. Sweetser, things went along so well at the start that I had time for a little reflection on what was going on inside the furnace. I saw the wood turned to charcoal practically, and it occurred to me, why should I use wood when I could put in the charcoal in the. first place, and thus save a lot of time, and also eliminate the dangerous gas from the wood, which is the cause of most of the accidents in starting up a furnace. I had a furnace out for repairs and decided to use no cord-wood in blowing in. I put in about a carload of charcoal and used no wood except some shavings and oily waste at each of the tuyeres. The furnace had 16 tuyeres and was 100 by 22 by 14.5 ft. Hot rods were put in each tuyere' and the blast started immediately at 11 a.m. Within 5 mill. the air was all driven out of the stack and the gas lighted of its own. accord at the top of the furnace. It was allowed to burn for 5 min. longer and then the bell was closed and the gas taken to the last stove and the last boiler on the gas-main. It was all clone so quietly that it was hard to realize that the gas was down. The tuyeres were as bright as if the furnace had been in blast for a long time. I have learned since that others have used the same method, but they had not passed the good advice along.

Jan 5, 1913

By P. L. Raffo, T. E. Mitchell

Single crystals of Ta-Re alloys have been deformed in tension and compression as a function of solute concentration and temperature. The temperature dependence of the yield stress is decreased by alloying. At low temperatures there is a minimum in the yield stress (at about 2 at. pct) as a function of concentration. Three-stage hardening was not observed in the alloys. Linear hardening rates, where observed, were characteristic of stage II in pure tantalum. At low temperatures and high concentrations, work softening was often prominent at high strains. Electron microscopy revealed that dislocations are mostly of screw orientation, although heavily jogged and cusped, and often occurring in dipole pairs. The alloys become more prone to cleavage with increasing rhenium content, due mostly to an increasing yield stress rather than a change in cleavage strength. Alloying apparently decreases the Peierls stress of bcc metals at low temperatures by facilitating kink nucleation at solule atoms on screw dislocations. Higher solute concentrations further increase the yield stress. Quantitative calculations and comparisons with other bcc alloy systems are made to show that the predominant hardening mechanism is due to the interaction of dislocations with misfitting solute atoms close to their slip planes. The interaction is so localized that the core dilatation of dislocations could be important. CONSIDERABLE interest has arisen in recent years concerning the mechanical properties of unalloyed bcc metal single crystals.'-7 These and similar studies on polycrystalline materials have resulted in a considerable understanding of the macroscopic yielding characteristics8, 9 and the process of work hardening.'' This latter advance is due in a large part to the increased use of transmission electron microscopy in P I RAFFO junior Membar AlMF is Metallyureist Iewis such studies and the general observance of three stages of work hardening in the shear stress-shear strain curves. The properties of substitutional alloy single crystals of bcc metals have not been determined in as much detail as in the pure metals. Insufficient systematic studies have been made on the effect of alloying on the magnitude and temperature dependence of the yield stress or the stress-strain curves. The alloy systems which have been studied to some extent have been Ta-W,11, 12 Ta-Mo," Ta-Nb,12'14 Mo-Re,15 W-Re,16 and alloys of iron with nickel,17 platinum,17 vanadium,18 and aluminum.18 A large body of data exists on Fe-Si alloys, but these have mainly been a result of the experimental convenience of using this material in place of unalloyed iron, rather than a comprehensive study of the mechanical properties of the alloy system per se. The present authors have previously reported additional data on the properties of Ta-Re, Ta-W, and Ta-Mo alloy single crystals.1g Some of the data on Ta-Re alloys will be described later in this paper. Briefly, single crystals of Ta-Re (1.2 to 10.6 pct), Ta-W (6.2 and 10.2 pct), and Ta-Mo (2.9 and 9.0 pct) were grown by the floating zone method in vacuum. Compression tests were performed in the temperature range 77" to 623°K. Slip was found to occur in Ta-Re alloys at 77' and 298°K on the (~ll)[lil] system and slip lines were coarser and straighter than in unalloyed tantalum. No three-stage hardening was observed in any of the alloy systems and the curves were nearly parabolic. At temperatures above 175°K the yield stress* increased monotonically with in- creasing composition while at 77" and 175°K the yield stress initially passed through a minimum after which it began to increase again for concentrations greater than about 2 pct Re. Similar minima were observed in Ta-Mo alloys and to a lesser extent in Ta-W alloys. The minimum was interpreted as being a result of a

Jan 1, 1969

By Ihor A. Kunasz

Lithium minerals occur predominantly in pegmatites which contain mineral assemblages derived from the crystallization of postmagmatic fluids or from the metasomatic action by residual pegmatitic fluids. They have been the traditional sources of raw materials for ceramic and chemical industries. However, with the discovery of Searles Lake, brines became new sources of lithium. Indeed, the 1960s may well be referred to as the "brine decade" because several brine bodies of significant economic importance were discovered. In the United States, the brines of Clayton Valley, Nevada, presently exploited by Foote Mineral Co., and the Great Salt Lake of Utah, to be exploited by the Great Salt Lake Chemicals Corp., have been defined as major sources of lithium. Also a lithium-bearing brine has been discovered in Chile. Following the termination of the AEC purchase program in 1959, several companies such as Maywood Chemical Co., American Lithium Chemicals, and Quebec Lithium Corp. were forced to close down their operations. Nevertheless, with the development of new applications in glass ceramics, air conditioning systems, synthetic rubber, and metallurgy (aluminum potlines), the lithium industry grew steadily, and with the potential application of lithium metal in batteries and nuclear reactors, a healthy growth can be foreseen. New products and new applications are likely to stimulate exploration for expanded reserves as well as the search for new sources from which lithium could be extracted economically. Geochemistry of Lithium Lithium is the third element in the periodic table. It is the lightest of all the metals, having an atomic weight of 6.938. Its ionic radius is 0.60A and its charge is + 1. The geochemistry of lithium has been extensively studied and has been summarized by Rankama and Sahama (1950), Goldschmidt (1937), and Hortsman (1957). The distribution of lithium in igneous rocks is controlled by its size and its charge, and by the (MgO+FeO)/Li2O ratio. In the early stages of crystallization of a magma, that ratio is very large. Consequently, both magnesium and iron are removed by ferromagnesian minerals in preference to lithium which is then concentrated in the residual magma. This results in an enrichment of lithium in silicic rocks and pegmatites (Strock, 1936). Pegmatites are coarse-grained igneous rocks formed by the crystallization of postmagmatic fluids. Minerals within pegmatites may also form by metasomatism (Jahns. 1955). Genetically, the pegmatites are associated kith neigh- boring intrusives. Mineralogically, granitic pegmatites contain feldspar, quartz, and mica as the main constituents and a variety of exotic elements such as lithium, beryllium, tantalum, tin, and cesium, which may or may not occur in economically significant concentrations. Detailed studies by numerous investigators (Cameron et al., 1949, 1954; Hanley et al., 1950; Jahns, 1953, 1955; Page et al., 1953) indicate that pegmatites often exhibit an internal zonal arrangement, with each zone containing a specific suite of minerals. The lithium minerals are usually found in the intermediate zones, and although as many as 13 zones have been recognized by Cameron, a complete zonal arrangement is rarely found. Zoning of pegmatite bodies has also been observed on a regional basis. The regionally zoned pegmatite sequences exhibit mineral assemblages and complexity according to their respective distance from the granitic bodies to which they are genetically related (Mulligan, 1965). Lithium is also found in small proportions in a variety of rocks. The average lithium

Jan 1, 1975

By Ihor A. Kunasz

Introduction Lithium minerals occur predominantly in pegmatites which contain mineral assemblages derived from the crystallization of postmagmatic fluids or from the metasomatic action by residual pegmatitic fluids. They have been the traditional sources of raw materials for ceramic and chemical industries. With the discovery of Searles Lake, brines became new sources of lithium. Indeed, the 1960s may well be referred to as the "brine decade" because several brine bodies of significant economic importance were discovered. In the United States, the brines of Clayton Valley, Nevada, are presently exploited by Foote Mineral Co. The brines of the Great Salt Lake of Utah, the Smackover formation, and the Imperial Valley geothermal field, have been defined as important resources of lithium. In South America, new occurrences have been identified in Bolivia and Argentina. At the Salar de Atacama, Chile, new production capacity is scheduled for 1984. Following the termination of the AEC purchase program in 1959, several companies such as Maywood Chemical Co., American Lithium Chemicals, and Quebec Lithium Corp. were forced to close their operations. Nevertheless, with the development of new applications in glass ceramics, air conditioning systems, synthetic rubber, and metallurgy (aluminum potlines), the lithium industry grew steadily, and with the potential application of lithium metal in batteries and nuclear reactors, a healthy growth can be foreseen. New products and new applications are likely to stimulate exploration for expanded, reserves as well as the search for new sources from which lithium could be extracted economically. Geochemistry of Lithium Lithium is the third element in the periodic table. It is the lightest of all the metals, having an atomic weight of 6.938, an ionic radius of 0.68Å and a charge of +1. The geochemistry of lithium has been extensively studied and has been summarized by Rankama and Sahama (1950), Goldschmidt (1937), and Hortsman (1957). The distribution of lithium in igneous rocks is controlled by its size and its charge, and by the (MgO+FeO) / Li2O ratio. In the early stages of crystallization of a magma, that ratio is very large. Consequently, both magnesium and iron are removed by ferromagnesian minerals in preference to lithium which is then concentrated in the residual magma. This results in an enrichment of lithium in silicic rocks and pegmatites (Strock, 1936). Pegmatites are coarse-grained igneous rocks formed by the crystallization of postmagmatic fluids. Minerals within pegmatites may also form by metasomatism (Jahns, 1955). Genetically, the pegmatites are associated with neighboring intrusives. Mineralogically, granitic pegmatites contain feldspar, quartz, and mica as the main constituents and a variety of exotic elements such as lithium, beryllium, tantalum, tin, and cesium, which may or may not occur in economically significant concentrations. Detailed studies by numerous investigators (Cameron et al., 1949, 1954; Hanley et al., 1950; Jahns, 1953, 1955; Page et al., 1953) indicate that pegmatites often exhibit an internal zonal arrangement, with each zone containing a specific suite of minerals. The lithium minerals are usually found in the intermediate zones, and although as many as 13 zones have been recognized by Cameron, et al. (1949), a complete zonal arrangement is rarely found. Zoning of pegmatite bodies has also been observed on a regional basis. The regionally zoned pegmatite sequences exhibit mineral assemblages and complexity according to their re-

Jan 1, 1983

By Frank E. Neil, O&apos

The formation tester, as the name implies, is a tool built for testing the contents of sands encountered in drilling Wells Without actually cementing casing on the sand. The tester was developed in the Mid-Continent and has been in use commercially there since about 1926. However, some two dozen patents have been issued on formation testers dating back to the seventies. The method apparently was an outgrowth of the old Mother Hubbard grain or bean packer, used around casing before the days of cementing casing. These packers were also seated in a tapered hole and if the formation tested was not satisfactory the casing was pulled loose and the hole taken down to another formation. A great deal of experimental work has been done in its development, and as a result of this work the formation tester became an accepted integral part of the petroleum development in California. The formation tester was introduced into California some three years ago by M. 0. Johnston. Months of discouraging and expensive work followed its introduction into this state, but one organization after another tried the tool and its use is now fairly general. Shortly after Johnston began testing in California, the Halliburton tester was also introduced into the state and now another tool is being introduced, the Shaffer-Roles tester. Principle and Operation of Testers The principle employed in all formation testers is that of packing off the fluid in the hole above the formation to be tested and thereby prevent,ing it from having access to the testing tool. This permits the fluid contained in the given formation to have unrestricted access to the tool. It is accomplished by running the tool and packer on the bottom of the drill pipe; the valves in the tool being closed while going into the hole to prevent fluid from entering the drill pipe. The packer is then seated at the desired point, trapping the drilling fluid above it. When this has been done, the valves in the tool are opened and the fluid from the formation is allowed to enter the empty pipe through the tool. If the

Jan 1, 1934

By B. B. Cox

Iraq, formerly called Mesopotamia in Asiatic Turkey, became a kingdom under British Mandate after the world war and is expected to gain its independence in 1932 when it enters the League of Nations. The kingdom is shown on Fig. 1 in its relations to neighboring countries, to the Mediterranean Sea and to the Persian Gulf. It is slightly smaller than the State of Texas with its capitol, Baghdad, inland about as far from the Persian Gulf as Breckinridge, Tex., is from the Houston Shipping Channel. The oil fields lie 180 to 225 miles north of Baghdad, or about as far as from Breckinridge to Oklahoma City, and about as far from the Mediterranean as Fort Worth is from Hobbs, N. M. A narrow-gage railway runs from Basra, the Persian Gulf port, to Baghdad. From there another narrow-gage runs into the Kurdish hills east of the Tigris to Kirkuk. A standard-gage, part of the old Berlin-Baghdad system, follows the west bank of the Tigris northward from Baghdad to Baiji, a village about 100 miles south of Mosul. No railway exists between Iraq and the Mediterranean, though the Anatolian Railways in southern Turkey come to within 50 miles of the Iraq frontier and 120 miles of Mosul. Surveys have been completed for a railway through British Mandates from Haifa to Baghdad as well as for a railway through French Mandated Syria from Tripoli to Abu Kemal near the Iraq border. Wagon roads, excepting those constructed by the oil companies, are few and indifferent in Iraq and no road exists across the desert to the Mediterranean, but contrary to prevalent beliefs the surface is firm and free from sand dunes so that motor cars can go almost anywhere in dry weather, with ease. Frequent motor car and airplane service exists between Baghdad and the Mediterranean ports and motor car service may be had between Kirkuk and Nisibin, Turkey, where on two days each week through Wagons Lits service is available to Paris. Baghdad is about 21 days distant from New York City with present transport facilities. The climate is semiarid, similar to Imperial Valley, California, the average rainfall outside the mountainous parts amounting generally to

Jan 1, 1932

By C. E. Shoenfelt

There was a notable decrease in drilling operations in 1940 in all of the Rocky Mountain states except Montana, where the two large fields on the Canadian border, Cut Bank and Kevin-Sunburst, were espe-cially active. The expanding markets for Montana natural gas made necessary the more intensive development of such fields as Rowdoin, Cedar Creek and Devon. While there were no important oil and gas discoveries in 1940 in any of the Rocky Mountain states, a few small pools were opened, which may constitute separate areas but may prove with later development to be extensions of old fields. Some of the old fields were extended and deeper pay zones were discovered in others. These have given the areas greatly increased oil reserves and therefore are just as important as the discovery of new fields. The more important of the developments in 1940 are given, by states, in the following paragraphs. Colorado Hiawatha Field, Moffat County.—The Mountain Fuel Supply Co. began the development at Hiawatha of its oil reserves, which were discovered in about 1929, and late in the summer oil began moving from the field by truck to the shipping point at Rock Springs, Wyoming. The Hiawatha field of northwestern Moffat County was discovered in 1927 by the Sormir Petroleum Co., with the completion of No. r Florence Wilson for 4,5,000,000 cu. ft. of gas a day from a Wasatch sand lens at 2200 it. In later development of the field, oil showings were reported in several wells but no development of this resource was undertaken until 1940, when a test of the oil possibilities was started with the release in April of a location for No. 5-A Wilson on the S\W. SW. NW. of sec. 23-1zN-1ooW., on the east side of the field. The Well had an initial production of 327 bbl. of oil a day pumping from three Wasatch (Tertiary) sands between 2005 and 2540 ft. It was drilled to 2562 ft., where the 65/8-in. casing was cemented and gun-perforated at 2005 to 2125 ft., 2260 to 2335 ft. and 2513 to 2540 ft. At the end of the year, this well was averaging zoo bbl. of oil per day, pumping. Two other wells were drilled for oil on Hiawatha during the summer—one a small well of 60 bbl. per day and the other a small gas well. Powder Wash Field, Moffat County.—The development of the Powder Wash field in northwestern Colorado was resumed in 1940 by the Mountain Fuel Supply Co., with the release of a location for No. 2-A Musser in the CWL.NW.SE. of sec. 4-1rN-97W. The Powder Wash field was discovered in 1931 by the Mountain Fuel Supply Co. and the discovery well, No. I Musser, on C.NW. of sec. 5-IIN-97W., was completed at 2152 ft. in the Hiawatha member of the nonmarine Wasatch for-mation for an open flow of 34,000,000 cu. ft. of gas per day under a natural pressure of 685 lb. per sq. inch. Oil was discovered in the Powder Wash field on Nov. 26, 1936, in the company's No. I Carl Allen on the NE.SW.SE. of sec. 32-12N-97W. The oil production was

Jan 1, 1941

By C. E. Shoenfelt

There was a notable decrease in drilling operations in 1940 in all of the Rocky Mountain states except Montana, where the two large fields on the Canadian border, Cut Bank and Kevin-Sunburst, were espe-cially active. The expanding markets for Montana natural gas made necessary the more intensive development of such fields as Rowdoin, Cedar Creek and Devon. While there were no important oil and gas discoveries in 1940 in any of the Rocky Mountain states, a few small pools were opened, which may constitute separate areas but may prove with later development to be extensions of old fields. Some of the old fields were extended and deeper pay zones were discovered in others. These have given the areas greatly increased oil reserves and therefore are just as important as the discovery of new fields. The more important of the developments in 1940 are given, by states, in the following paragraphs. Colorado Hiawatha Field, Moffat County.—The Mountain Fuel Supply Co. began the development at Hiawatha of its oil reserves, which were discovered in about 1929, and late in the summer oil began moving from the field by truck to the shipping point at Rock Springs, Wyoming. The Hiawatha field of northwestern Moffat County was discovered in 1927 by the Sormir Petroleum Co., with the completion of No. r Florence Wilson for 4,5,000,000 cu. ft. of gas a day from a Wasatch sand lens at 2200 it. In later development of the field, oil showings were reported in several wells but no development of this resource was undertaken until 1940, when a test of the oil possibilities was started with the release in April of a location for No. 5-A Wilson on the S\W. SW. NW. of sec. 23-1zN-1ooW., on the east side of the field. The Well had an initial production of 327 bbl. of oil a day pumping from three Wasatch (Tertiary) sands between 2005 and 2540 ft. It was drilled to 2562 ft., where the 65/8-in. casing was cemented and gun-perforated at 2005 to 2125 ft., 2260 to 2335 ft. and 2513 to 2540 ft. At the end of the year, this well was averaging zoo bbl. of oil per day, pumping. Two other wells were drilled for oil on Hiawatha during the summer—one a small well of 60 bbl. per day and the other a small gas well. Powder Wash Field, Moffat County.—The development of the Powder Wash field in northwestern Colorado was resumed in 1940 by the Mountain Fuel Supply Co., with the release of a location for No. 2-A Musser in the CWL.NW.SE. of sec. 4-1rN-97W. The Powder Wash field was discovered in 1931 by the Mountain Fuel Supply Co. and the discovery well, No. I Musser, on C.NW. of sec. 5-IIN-97W., was completed at 2152 ft. in the Hiawatha member of the nonmarine Wasatch for-mation for an open flow of 34,000,000 cu. ft. of gas per day under a natural pressure of 685 lb. per sq. inch. Oil was discovered in the Powder Wash field on Nov. 26, 1936, in the company's No. I Carl Allen on the NE.SW.SE. of sec. 32-12N-97W. The oil production was

Jan 1, 1941

The following figures (Nos. 1-4) and tables (Nos. 1 and 2) were inadvertently omitted from the chapter entitled "Optimum Open-Pit Mine Production Scheduling" by Thys B. Johnson, Section 4, pages 539-562. [ ]

Jan 1, 1969

By S. R. Elliott

THE principles of the caving system, as they apply to mining of soft iron-ore deposits, are well known, as this method has been in use for many years. It is, however, necessary to give a general description of it before describing the Athens method. The shaft and surface equipment should be placed at a sufficient distance from the orebody, so that the caving and pulling of the surface will not disturb the operations of the mine. Levels are started at the proper intervals, and when raises are completed, slicing commences at the top of the orebody and progresses downward. The necessary precautions are taken to avoid the occurrence of large open rooms and it is customary to break sufficient capping to form a mat to prevent heavy falls of ground from crushing through to the lower sublevels and endangering the lives of the workmen. Slicing is continued, and when sufficient width and length are undercut, the capping commences to cave, and in time a settlement occurs at the surface. As soon as this caving commences, the pressure on the timber naturally increases; after it extends to the surface, the amount of pressure has a certain relation to the depth. In other words, the pressure increases with the depth, but not in direct proportion. At great depths, such as that found at the Athens, 2500 ft. (760 m.), the pressure might be so excessive that the cost of keeping working places open would be prohibitive. The actual caving of the surface in a deep mine, with a great thickness of capping, is slow and often takes years to accomplish. After sufficient width and depth -have been undercut, the capping starts to break away, but through arching large masses of rock-.fill the opening, support the capping, and retard the continuation of caving. Caving to the surface is, therefore, retarded until either a sufficient thickness of the orebody is removed, or the width and length of the undercut part have been greatly increased. I wish to emphasize this fact of slow caving, for it is on, this principle that the success of the Athens system. largely depends.

Jan 8, 1920

By P. S. Roller

P. S. ROLLER,*College Park, Md.-The author introduces the idea of a grind limit, or lower size limit of the particles formed directly by grinding, and this is stipulated to be 0.70 micron. I wonder where all the particles come from that lie between the resolving power of the microscope and 0.7 micron, which are seen under a microscope in examining a sample of grind? There is also introduced the idea of excess fines; this is all right in itself but the author's quantitative definition seems to be virtually impossible to justify, and, moreover, is obscure. Just why E, the excess fines, should he defined as the distance between an F line and a y line is hard to follow, and just where the distance should be measured does not appear to be stated, as it should be since the F and y lines intersect and the distance between will depend upon where that distance is measured. The basis of the presentation is the relation of log weight against log size that was "discovered" by Schuhmann. While this relation is implied to fit, the only evidence that I can see is a slightly irregular line in Fig. x between 2 per cent and 18 per cent by weight and then a precipitous drop at 18 per cent away from any sort of straight line. Some of the conclusions are rather startling. It is stated that E, the excess fines, remains constant for all the comminution products of any particular material, except that it may decrease for some coarse crusher products. No reason is given for this assertion. One would, on the contrary, expect that excess fines, if such a concept is permissible, would generally vary with different conditions instead of being constant. Again, "as much net energy is required to reduce a ton of quartz to particles of the grind-limit diameter (namely, of course, 0.7 micron) by grinding as is required to melt the quartz." This would require many data to prove, but no proof is given; any consideration would reveal the impossibility of such a result. Still further, ore samples "ground to widely different sizes, and with different circulating loads and different size distributions or product, show the same production of new surface area per revolution of the mill, when this grind limit is used." This statement is confuted by ordinary experience, which teaches that grinding efficiency varies generally with the condition of material. For example, the cushioning effect of fines is widely accepted, while the inefficiency of a ball mill when the feed is too coarse is also well known. R. SCHUHMANN, JR.," Cambridge, Mass. Contrary to Mr. Bond's stand, there is a great deal of miscellaneous experimental evidence that comminution does not stop at around 0.7 micron, nor does it cease consuming energy at that point. Comminution is in fact recognized as an important method of producing colloids., Mechanical comminution methods were used by von Weimarn6 to produce colloidal dispersions of a variety of solids, including the minerals chalcocite, galena, hematite, stibnite. Utzino7 gives average particle sizes ranging from 0.02 to 0.09 micron for colloids produced by mechanical comminution of several crystalline solids. Andreasen and Berg' have ground

Jan 1, 1941

By Wallace Ralston

DuRing the year of 1937, the East Texas district produced 211,194,467 hbl. of oil and marketed more than 22,329 million cu. ft. of gas; 3377 oil and gas wells were completed. During this same period 106 exploratory wells were drilled, discovering three new oil fields and one gas-distillate field. Fields East Texas Field.—The East Texas field again led the district as to production and number of wells completed. During the year, 2420 oil wells were completed, making a total of 24,382 producing wells, which produced 171,336,854 bbl. of oil, for a total of 1,156,352,834 bbl. since the beginning. During the year the average bottom-hole pressure dropped 49 lb., making the average bottom-hole pressure 1119 lb. Approximately 3500 wells are making salt water, 20 per cent of them making over 80 per cent of the water. During the month of December, the daily average production of salt water was 119,000 barrels. Talco Field, Titus and Franklin Counties.—The Talco field produced 9,780,948 bbl. of oil during the year, from 637 wells. During the year 472 wells were completed. All of the wells are pumping and 241 are making salt water. This field has followed a normal development and did not exceed the estimated number of acres reported last year. Rodessa Field, Cuss and Marion Counties.—The Rodessa field was extended about 13 miles southwest into Marion County, which added approximately 4000 acres to the field. During the year 260 wells were completed, making a total of 416 producing wells, which produced 12,646,-970 bbl. of oil. The author was unable to obtain figures for the amount of gas produced. The field has two gasoline plants, which had a daily average of 16,558,000 cu. ft. of gas during December, averaging 0.83 gal. per M cu. ft. As of Jan. 1, 31 wells were making salt water. The bottom-hole pressure varies greatly, depending upon the pay from which the well is producing. The average bottom-hole pressure from the Young

Jan 1, 1938

By P. S. Roller

P. S. ROLLER,* College Park, Md.-The author introduces the idea of a grind limit, or lower size limit of the particles formed directly by grinding, and this is stipulated to be 0.70 micron. I wonder where all the particles come from that lie between the resolving power of the microscope and 0.7 micron, which are seen under a microscope in examining a sample of grind? There is also introduced the idea of excess fines; this is all right in itself but the author's quantitative definition seems to be virtually impossible to justify, and, moreover, is obscure. Just why E, the excess fines, should be defined as the distance between an F line and a y line is hard to follow, and just where the distance should be measured does not appear to be stated, as it should be since the F and y lines intersect and the distance between will depend upon where that distance is measured. The basis of the presentation is the relation of log weight against log size that was "discovered" by Schuhmann. While this relation is implied to fit, the only evidence that I can see is a slightly irregular line in Fig. I between 2 per cent and 18 per cent by weight and then a precipitous drop at 18 per cent away from any sort of straight line. Some of the conclusions are rather startling, It is stated that E, the excess fines, remains constant for all the comminution products of any particular material, except that it may decrease for some coarse crusher products. No reason is given for this assertion. One would, on the contrary, expect that excess fines, if such a concept is permissible, would generally vary with different conditions instead of being constant. Again, "as much net energy is required to reduce a ton of quartz to particles of the grind-limit diameter (namely, of course, 0.7 micron) by grinding as is required to melt the quartz." This would require many data to prove, but no proof is given; any consideration would reveal the impossibility of such a result. Still further, ore samples "ground to widely different sizes, and with different circulating loads and different size distributions or product, show the same production of new surface area per revolution of the mill, when this grind limit is used." This statement is confuted by ordinary experience, which teaches that grinding efficiency varies generally with the condition of material. For example, the cushioning effect of fines is widely accepted, while the inefficiency of a ball mill when the feed is too coarse is also well known. R. SCHUHMANN, JR.,* Cambridge, Mass.-Contrary to Mr. Bond's stand, there is a great deal of miscellaneous experimental evidence that comminution does not stop at around 0.7 micron, nor does it cease consuming energy at that point. Comminution is in fact recognized as an important method of producing colloids.5 Mechanical comminution methods were used by von Weimarn6 to produce colloidal dispersions of a variety of solids, including the minerals chalcocite, galena, hematite, stibnite. Utzino7 gives average particle sizes ranging from 0.02 to 0.09 micron for colloids produced by mechanical comminution of several crystal-line solids. Andreasen and Berg8 have ground

Jan 1, 1941

By D. L. McDanels, J. W. Weeton, R. W. Jech

An investigation was conducted to determine the stress-strain behavior and tensile properties of metallic composites and to relate them to the properties of the base materials. Tungsten fibers in a copper matrix were chosen as the model sys-tem to investigate these properties. Room-temp-atzcre tensile and dynamic -modulus tests were used To meet the demand for improved structural materials, considerable effort is being directed toward the creation of composite materials. One such material under investigation is the fiber-reinforced composite, in which a ductile, relatively weak matrix is reinforced with high-strength fibers. Some work has been done on the reinforcement of metallic matrices with metallic fibers1"5 as well as with ceramic-whisker reinforcement. Summaries of much of this work have been published by Mach-lin7 and Baske~.' Work done at the Lewis Research Center of NASA-" has involved the making and testing of composites composed of a fiber, tungsten, and a matrix, copper, which were insoluble in each other. An equation was presented that showed the relation between the ultimate tensile strength of the composites and the strengths and relative volume percents of the components. This relation was verified experimentally for composites containing fibers extending the full length of the specimen as well as for composites reinforced with short-length or discontinuous fibers. Since the publication of the preliminary results,9'10 additional data have been obtained. This paper presents these data as well as analyses of the stress-strain behavior and the mechanics of deformation of uni-axially oriented, fiber-reinforced metallic composites, in which both components are mutually insoluble. EXPERIMENTAL PROCEDURE Composites were made with high-purity copper as the matrix and 3-, 5-, and 7-mil-diam tungsten wire as the reinforcing fiber. Some specimens were made in which the reinforcing fiber extended completely through the full length of the composite test section. The fibers were placed in ceramic to determine these properties. The composites were reinforced with either continuous or discontinuos tungsten fibers. The tensile properties and stress-strain behavior of composites reinforced with either type of reinforcement were similar, and in both cases the full strength of the fiber was utilized. tubes to insure axial orientation and infiltrated with copper at 2200°F for 1 hr. Composites were also made with short-length (3/8 in. long) 5-mil-diam tungsten fibers as discontinuous reinforcement and infiltrated under the same conditions. The reinforcing fibers in both cases were longitudinally oriented in the direction parallel to the tensile axis. Room-temperature tensile tests were conducted on the composites, stress-strain curves were obtained, and ultimate tensile strength and elongation were measured. Dynamic modulus of elasticity, based upon the resonant frequency induced in the flexural mode of vibration, was also determined for the composites and the components. A more detailed discussion of the experimental procedure employed in this investigation may be found in Ref. 11. RESULTS Room-temperature tensile tests were conducted on 3-, 5-, and 7-mil-diam tungsten wires which had been annealed for 1 hr at 2200°F and show the tensile strength of the wires to be 331,000, 327,000, and 290,000 psi, respectively. Since all the composites were infiltrated under these conditions, the strengths were considered to represent the strength of the fibers in the composites throughout this study. The average tensile strength of the annealed copper used as the matrix in this investigation was 27,800 psi. Results of room-temperature tensile tests on composites reinforced with 3-, 5-, or 7-mil-diam tungsten fibers are plotted as functions of composition in Fig. 1. These data represent previously reported datag,l0 as well as data more recently obtained. The line shown on each curve represents a prediction of tensile strength as a function of composition; the calculation of this line was explained in Refs. 9 and 10. A similar plot is presented in Fig. l(d) for composites reinforced with short-length, discontinuous 5-mil-diam tungsten fibers. Again, both the previously reported and the recent data are presented, and the line shown is identical to that shown for

Jan 1, 1965

In mid-November, a long awaited announcement was made by John Drybrough, President of Granduc Mines Ltd. In short, he said that the extensive exploration conducted by his company and its parent organization, Newmont Mining Corp., have indicated the feasibility of a commercial copper mining operation at the company's prospect located slightly north of Stewart, B.C., and just east of the Alaskan Panhandle. The financing of the project is now being planned. SUMMARY OF PROJECT Granduc reasonably assured ore reserves are estimated at 32,510,000 tons averaging 1.93% copper content before dilution, of which 20,670,000 tons averaging 2.08;:; copper content are situated above the proposed mine access tunnel at elevation 2475 above sea level. The life of the reserves at the planned rate of production is 13 1/2 years. The probability of finding substantial additions to these present reserves is considered good.

Jan 12, 1963