Search Documents

By R. N. Hoffman

A new technique for determining capillary pressure curves has been developed and tested. The technique differs from previously reported centrifuge techniques in that the centrifuge is slowly accelerated from zero to the maximum desired speed rather than being held constant at particular, progressively higher speeds. An important advantage of this technique over other methods of determining capillary pressure curves is the short time required to obtain the desired amount of data over the chosen pressure range. For example, to obtain 30 data points between 1.2 and 104 psig with a 1.55-in. long, 3/4-in. diameter core using a brine-air system, 6.6 hours were required with this technique. An equally important development of this paper is an analytic method for the conversion of the data from the centrifuge experiment to capillary pressure curve data. Previously there has been only an approximate conversion available. Although the capillary pressure curves determined by this technique appear to be as accurate as those determined by other techniques, the accuracy could be improved if certain variables, not treated in this experiment, were investigated. Among these are the dynamic distortion of the centrifuge equipment and imperfect initial saturation of the cores. INTRODUCTION Pirson 1 defines capillary pressure in a porous medium as "the differential pressure that exists between two fluid phases at their interfaces when they are distributed under static equilibrium within a porous material". Capillary pressure in rocks is known to be a function of fluid saturation, among other things, and a capillary pressure curve is defined for the purposes of this paper as a plot of the capillary pressure-wetting phase saturation relationship for a particular rock sample. Several methods are used for determining capillary pressure curves for small rock cores. Prominent among these are the semi-permeable barrier, mercury injection, and, to a lesser extent, centrifuge methods. The semi-permeable barrier method is currently the most popular. It features simplicity in both execution and the mathematical conversion of the experimental data into a capillary pressure curve. The main disadvantages of the semi-permeable barrier method are the time required — as long as two months — to obtain several points for the curve, and a fairly low maximum pressure before breakthrough of the non-wetting phase into the barrier occurs, for example, about 32 psig for a brine-air system. It is for these reasons that other methods such as the centrifuge method have been introduced. High accelerations and the absence of a barrier result in quicker attainment of saturation equilibrium at a given pressure. However, the centrifuge method involves much more expensive equipment and more difficult procedures and calculations than does the barrier method. The purpose of this investigation has been to improve the equipment and procedures of the centrifuge method and to develop an analytic method for the conversion of the experimental data into a capillary pressure curve. Hassler and Brunner did the original work in the determination of capillary pressure using a centrifuge. In their work the centrifuge speed was increased in a step-wise manner, each speed being held constant until saturation equilibrium was reached in each core. Saturation equilibrium was indicated when the volume of liquid collected in the graduated pipette of the core holder remained constant. According to Hassler and Brunner, equilibrium was reached in "a few minutes to one-half hour or more". In the centrifuge method, as opposed to the barrier method, the fluid saturation of the core is not a constant throughout the length of the core, but varies with the radius of centrifugation. Also, the capillary pressure cannot be read directly but must be calculated from a knowledge of the centrifuge speed and other parameters. For these calculations, Hassler and Brunner derived the following equations:

By J. Handin

Triaxial compression tests with independently applied external confining pressures and internal pore pressures show that the ultimate compressive strengths of representative oil well cements are nearly linear functions of effective pressure — the difference between external and internal pressures on the jacketed cylindrical specimens (to 15,000 psi). The strengths are little affected by the test temperature to 350F (not to be confused with the curing temperature). At an effective pressure of 15,000 psi, strengths are in the rage of 30,000 to 50,000 psi, comparable to those of sedimentary rocks under similar conditions. The cements become very ductile even under low effective pressures; permanent shortenings of 30 per cent or more are attainable without rupture. INTRODUCTION Since the pioneering work of Richart, Brandtzaeg and Brown1 on the failure of cement under combined compressive stresses, it has been recognized that ultimate compressive strength is greatly enhanced by the application of confining pressure. More recently, Mc Henry2 showed that the strength of concrete was a linear function of the effective pressure (the difference between the external confining pressure on a jacketed specimen and the internal fluid pore pressure), at least for a range of 0 to 1,500 psi. The effect of temperature had not been investigated, and no previous systematic triaxial compression testing of naterials used for oilwell cementing seems to have been done. The present work was suggested by the late J. hi. Bugbee3 who stated that "consideration of the common application of high-pressure hydraulic fracturing to the initial completion or recompletion of wells, and the large pressure drawdowns in some producing wells, particularly those in abnormally high-pressure gas-condensate reservoirs, raises the question of what is a suitable cement strength for various completions. The intuitive belief exists that cement strength need be no greater than formation strength. Tests should, however, be conducted at downhole conditions." The ultimate compressive strengths of rocks penetrated by the borehole must rise several fold with increasing depth.4 This marked enhancement of strength is due to the influence of the effective pressure, the total weight per unit area of the overburden less the hydrostatic pore pressure. (The effect of temperature due to the geothermal gradients is relatively small for depths to 30,000 ft.) .A significant comparison of the strengths of rocks and cements at downhole conditions requires knowledge of the confined compressive strengths of cements as well. EXPERIMENTAL PROCEDURES The theory and technique of triaxial compression testing are fully discussed in earlier reports.4-6 Briefly, cylindrical specimens 1-in. long and 0.5-in. in diameter are jacketed in thin copper tubes of negligible strength, placed in the test chamber and subjected to an external confining pressure of kerosene and loaded axially by the piston at a strain rate of 1 per cent per minute. Pore pressures of water (or kerosene) are applied independently through the hollow piston and are maintained constant during the shortening of the specimen, Tests at sensibly 0 pore pressure are arranged so that any free water in the cement can escape to the atmosphere. (If egress of water were denied, pore pressure would rapidly attain the value of the external confining pressure because of reduction of pore space.) The test chamber can be heated for high-temperature experiments. Unless otherwise noted, the cement samples were air dried for about a week. Recorded during a test are pore and confining pressures, shortening and axial differential force (total force less the product of the confining pressure and the area of the piston). True stress-strain curves are constructed by dividing the measured differential force by the actual cross-sectional area of the specimen at a given

Jan 1, 1966

By V. Rajaram

The oil shales of the Green River Formation in the United States have been considered as a source of liquid hydrocarbons since 1908, with the first retort constructed in Colorado in 1917. However, it was not until 1944 that the mining characteristics of oil shale were investigated in a systematic manner. During the period 1944 through 1956, the Selective Mine and the Demonstration Mine (also referred to as the Anvil Points Mine) were operated by the U. S. Bureau of Mines (USBM) near Rifle, Colorado. Significant progress was made in developing a room and pillar mining method by which oil shale could be mined safely at a very low cost per ton. Mechanical properties of oil shale were determined, safe room spans and roof support techniques were established, and drilling and blasting methods for oil shale were developed. As a follow-on to this USBM effort, a consortium of six oil companies with Mobil Oil Company as project manager carried out a research program during the period 1964-68 at the Mobil mine, located in the vicinity of the Anvil Points mine. Rock mechanics investigations were conducted as a part of this research program, and consisted of laboratory studies, in-situ stress determinations, and roof and pillar instrumentation. This paper will discuss the findings at the Anvil Points mine and Mobil mine to illustrate the stability considerations in underground oil shale mining.

Jan 1, 1983

By E. P. Abrahamson

The effect of transition element binary solid solution additions upon the recrystallization temperature of titanium has been investigated. All additions, except columbium and tungsten, raised the recrystallization temperature. A correlation is obtained between the logarithm of the absolute rate of change of recrystallization temperature with atomic percent solute and the number of uuter d shell electrons attributed to the free atom of the solute element in its ground state. The work of Abrahamson, et aL.1-6 on dilute binary solid solution alloys indicated a correlation between the free atom ground state electron configuration of the solute and both the brittle-ductile transition and recrystallization temperature. It is shown in these studies that the number of outer s and d electrons in the solute are of prime importance in determining the absolute rate of change of recrystallization or transition temperature with composition. Furthermore, the limit of initial linearity (in the curve of recrystallization temperature vs at. pct solute) has been shown to be a function of the number of d shell electrons in the solute for dilute iron- and vanadium-base alloys. To date no complete systematic recrystallization study of dilute binary titanium base alloys has been made. This study together with that of zirconium base alloys 6 will provide the data for the comparison of the effect of the same solutes upon two solvents with the same number of outer d shell electrons.

Jan 1, 1962

By M. M. Singh, H. L. Hartman

This paper reports on the results of a fundamental investigation of the behavior of rock under impact of a chisel-shaped bit. Drop-tester studies were conducted with strain gauges attached to the rock and striking bit-edge. It was established that rock behaves viscoelastically. Little correlation was found to exist between the strain waveforms detected on the rock surface and in the bit; thus, strain-time curves obtained with transducers mounted on the bit cannot be used to explain the sequence of events in rock breakage. It is estimated that nearly 1 per cent of the total energy of the blow is expended in permanent deformation of the rock. The strain- energy distribution on a rock surface as a result of chisel impact, which follows a simple law, is presented graphically. Experiments also were conducted with gauges embedded in the rock vertically below the line of impact and at an angle of approximately 45' to the vertical. No essential difference was observed in the type of wave obtained with embedded gauges and with gauges on the surface, as may have been anticipated from theory. INTRODUCTION Through the ages great strides have been taken towards improvement of the various techniques applied in the breakage of rock. Indeed, numerous applications of the rock-failure process are an integral part of present-day industry, including oil well drilling. Yet, astonishingly, little is known regarding the behavior of rock under dynamic loading or the mechanism of rock failure. The value of impact loading studies from the point of view of drilling is evident, however, and requires little elaboration because impact of a chisel edge on rock forms the basic action constituting most common methods of drilling. RELATED STUDIES Impact studies of communition and fragmentation conducted by Fahrenwald, et a1,8 Poncelet,l7 Axelson, et a1,2 Piret,16 Hartman and pfleider,ll Charles and deBruyn,5 and others have been of considerable help in understanding rock-breakage phenomena. Further insight into the basic action of drilling and penetration has been obtained by the work of Irving,13 Cherkasov and Shlyapin,6 BOrcherdt,3 Shepherd,19 Shreiner and Pavlova,20 Drilling Research Inc.7 Hartman,10 Appl and Gatley1 and several other investigators. However, knowledge concerning the stresses and strains induced in the rock and bit during impact remains scant. Recent photoelastic studies by Tandanand and Hartman (1961. 1962)22, 23 have shed light on stress distributions and Fracturing produced in plastics by chisel-shaped bits. In the field of transient strain Pulses and their role in rock drilling, the only extensive work has been performed by Drilling Research Inc. (DRI). They attached strain gauges to the shank of a bit and conducted drop-tester studies, using a die-shaped bit to obtain force-time diagrams. Their work led to the conclusion that, for a given rock type, the first peak of force occurs at a fixed level regardless of the total energy in the system, provided it exceeds a certain minimum threshold level. Further, on this basis an explanation was offered for the sequence of events in crater formation as the result of a single blow on rock. PURPOSE OF PRESENT STUDY The investigations reported in this paper were conducted in a manner similar to the DRI approach, but with the objective of determining the strain distribution in the rock around the area of bit impact and, to a limited extent, the strain in the chisel-shaped bit itself. It was expected that a knowledge of the disposition of these strains, along with the rate of attenuation of strain energy in the rock

By P. M. Blair, D. W. Peaceman

The shape and position of the gas-oil transition zone during downdip displacement of oil by gas has been calculated using flow equations which include the effects of gravity, relative permeability, capillary pressure and compressibility of the fluids. The calculations treat the problem in two space dimensions, and results are compared with data from a laboratory model tilted at 30° and 60° from the horizontal on displacements near and above the maximum rate at which gravity segregation prevents channeling of the gas along the top of the stratum. The good agreement between calculated and experimental results demonstrates the validity of the tecbnique as well as that of the flow equations. INTRODUCTION Knowledge of the fluid distribution and movement in an oil reservoir is important in producing operations and estimation of reserves. The history of the oil industry has included steady progress in improving the accuracy of calculations which provide the required knowledge. The earliest method of calculating reservoir performance consisted of material-balance equations based on the assumption that all properties were uniform throughout a reservoir.l For many reservoirs such a simple formulation is still the most useful. However, when large pressure and saturation gradients exist in a reservoir, the assumption of uniform values throughout may lead to significant error. To reduce these errors, Buckley and Leverett2 introduced a displacement eqation which considers pressure and saturation gradients. Methods available at that time permitted solutions to the Buckley-Leverett equation in one space dimension; these solutions have been very useful in solving many problems related to the production of oil. However, the one-dimensional methods are not adequate for systems in which saturations vary in directions other than the direction of flow. An example of such a system is the case of gas displacing oil down a dipping stratum in which the gas-oil contact becomes significantly tilted. Of course, the Buckley-Leverett displacement method cannot predict the tilt of the gas-oil contact. Recent improvements3,4 of the one-dimensional Buckley-Leverett method achieve some success in predicting the tilt of the gas-oil contact at sufficiently low flow rates. However, at rates high enough that the viscous pressye gradient nearly equals or exceeds the gravity gradient, even these improved one-dimen,sional methods incorrectly predict the shape and velocity of the contact. Further progress in estimating such fluid movements in a reservoir appears to require consideration of the problem in more than one space dimension. The recent two-dimensional method of Douglas, Peaceman and Rachford5 appears adaptable to calculate changes with time of the saturation distribution in a vertical cross-section of a reservoir. The movement of saturation contours should represent the moving fluid contacts and include the effects of crossflow due to gravity, as well as variations in the rock and fluid properties. The nonlinear nature of the equations used in the method has prevented proof of the validity of the solutions. Douglas, Peaceman and Rachford made some comparisons with experiment but did not include cases in which gravity was important nor cases involving displacement by the nonwetting phase.For these reasons, a test of the two-dimensional method for a case in which these factors are included would be very desirable. The test selected was a comparison of calculated results with those from a carefully controlled laboratory experiment on a model with measured physical properties. The model selected was one in which gas displaced oil down a tilted, rectangular sand pack. The model can be thought of as representing a vertical cross-section taken parallel to the dip of a reservoir. The displacement thus simulates gas displacing oil downdip that might result from gas-cap expansion or gas injection. This report outlines the calculation method used

By C. B. Scotty, E. F. Egan

INTRODUCTION The neutron-garnma log has been used for stratigraphic correlation by the oil industry for a number of years. In the past few years, the quantitative application of the log to provide information with respect to porosity has received considerable attention. The basic concept of quantitative interpretation has been pointed out in the literature.1 It shall be the purpose of this paper to develop by empirical means a method whereby the relationship of porosity to neu. tron-gamma deflection may be predicted for various bore hole diameters. This relationship is applicable to the present commercially available neutron-gamma log run in open hole. Data available at present are insufficient to establish similar correlations for cased holes. Through the development of such a correlation, the importance of the various factors which influence the log become evident. NEUTRON-GAMMA CURVE The logging tool conisists of a source of neutrons and a means of detecting and measuring gamma rays, the detector being shielded from the direct emission from the source. The gamma rays reaching the detector have three sources of origin: (1) the natural gamma radiation emitted by the formations, (211 induced gamma radiation resulting from neutron bombardment. (3) gamma rays emitted by the source and scattered by the formation. It has been found that a neutron derived porosity correlation is best for shale-free formations. Under this condition the natural gamma ray radiation is quite low, and therefore, will be neglected in this work. The induced gamma ray radiation resulting from neutron bombardment is predominantly a function of the hydrogen atom concentration of the substance penetrated. Due to the geometry of the presently used system, the neutron-gamma curve indicates low radioactivity opposite high hydrogen concentration and high radioactivity opposite low hydrogen concentration (Figs. 1 and 2). Having a curve which measures hydrogen atom concentration, it follows that if the matrix of the formation penetrated consists only of atoms other than hydrogen, and if the fluid filling the pores is either oil or water, the curve should be an indication of porosity (both oil and water have practically the same number of hydrogen atoms per unit volume'). The above criteria for a porosity (Correlation are fulfilled in clean sandztones and limestones in which the pore volume is completely filled with liquids (oil or water), but not in formations containing either free gas or shale or both. Free gas. even under pressure, contains considerably less hydrogen per unit volume than oil and water; therefore, a variation in response on the curve would be expected. Camp- bell and Winter,' indicate that this difference in hydrogen concentration is sufficient to distinguish between sands containing water or oil and those containing dry gas. Shale is a mineral that contains hydrogen in its molecular structure in addition to the hydrogen which is present in the water of hydration. Thus, in formations containing variable amounts of shale, the hydrogen concentration indicated by the curve is not a direct indication of porosity. Bush and Mardock' have indicated that a correction may be made by use of the gamma ray curve to provide a porosity correlation. Since the induced gamma rays are predominaiitly a function of hydrogen concentration, it would be anticipated that the fluid filled bore hole would materially influence the logs. It has been pointed out that the neutron-gamma curve response decreases with increase in hydrogen concentration, therefore, the response due to the induced gamma ray component decreases with increase in fluid filled hore hole diameter. The scattered gamma ray component of the log increases with increase in bore hole diameter. Although there is an

Jan 1, 1952

By T. D. Mueller, F. C. Miller, Jr. Earlougher R. C.

In analyzing pressure buildup tests for field wells producing both oil and gas, the common practice is to use a modification of single-phase flow theory. Validity of such an approximation has been demonstrated for single-well solution-gas-drive systems. This paper indicates that such approximations are also valid for two-well solution-gas'-drive systems. From this it is inferred that the technique can be used for multiple-well systems. A computer was used to simulate the behavior of a two-well solution-gas-drive reservoir to test the validity of the above type of analysis. Simulation results indicate that pressure buildup tests in such a system can be analyzed within engineering accuracy for formation permeability and pressure. A rule of thumb is given for estimating the length of time a well must be shut in for the pressure in a nearby producing well to increase significantly. To observe such an increase, the shut-in well would have to be left shut in much longer than normal. INTRODUCTION An important technique for obtaining data concerning a producing petroleum reservoir is the pressure buildup test. Such a test, when properly conducted and analyzed, provides information on the average reservoir pressure and the permeability in the major drainage area of a well. The theory upon which the analysis of a pressure buildup test is based assumes that the behavior of the fluid in the reservoir is adequately described by the diffusivity equation.1 Use of the diffusivity equation implies that a single fluid of small and constant compressibility is flowing. To analyze a pressure buildup test in situations which involve more than one fluid phase, the single-fluid analysis is extended. This paper verifies the extension of pressure buildup analyses to two-phase, two-well systems. Miller, Dyes and Hutchinson1 have presented a technique for analyzing pressure buildup tests in circular bounded reservoirs. Their method requires that the reservoir be producing at pseudo-steady state (constant pressure gradients) prior to shut-in. An alternate reservoir model, presented by Horner,2 assumes that the reservoir is infinite. The Homer model does not assume a Pseudo-steady state prior to shut-in, but the assumption that the reservoir is infinite implies that the average pressure can be determined only if the total production prior to shut-in is small compared to the total fluid originally present. Limitations imposed by the pseudo-steady state and infinite reservoir assumptions are avoided by the technique proposed by Matthews, Brons and Hazebroek.3 Their method can be used to calculate both the Permeability and the average pressure in bounded single-well systems which are not necessarily at steady state. They also suggested determining the average pressure of a multi-well reservoir producing from pseudo-steady state by volumetrically averaging the static pressures of the individual wells. Matthews and Lefkovits4 used numerical simulation techniques to verify that this method does produce adequate results for single-phase, multiple-well systems. Perrine5 proposed modifications to the single-phase theory so that pressure buildup tests in multiple-phase systems could be analyzed. He suggested replacing the single-phase mobility (k/µ) by the sum of the mobilities of the individual phases, and replacing the fluid compressibility by an average compressibility weighted by the saturations of the separate phases. By using numerical techniques to solve the two-phase flow problem for a single-well system, he concluded that this approximation gives results within engineering accuracy. More recently, Weller6 has shown that, for a gas-oil system with a single well at the center of a circular reservoir, pressure buildup tests can be analyzed adequately by using the modification proposed by Perrine. Feller's results also indicate that, as the gas saturation increases, this analysis becomes less accurate. To date, no evidence is available to show that the Perrine approximations can be combined with the Matthews-Brons-Hazebroek technique to calculate the average pressure of a multi-well,

W. Morton Webb, Germiston, Transvaal, South Africa (communication to the Secretary*):—The experience of Mr. Boeh-mer in the Leadville district and his reputation as an engineer assure the interest of anything he may write on the ore-bodies of that district; and all engineers who have operated in Leadville will agree that the theory of the origin of the Leadville deposits, as given by Mr. Emmons in his famous monograph, does not adequately explain the genesis of all the deposits. The solutiou of the problem does not, however, appear to be quite so simple as Mr. Boehmer would make it; and the advance pamphlet issued by the U. S. Geological Survey, pending the completion of the main report, shows that there is still much ground for controversy. No doubt the later eruptive0 had a greater influence on the deposition of the ore-bodies than was thought at the time of the first investigation by the Survey; but it has always appeared to me that the influence exerted by these dikes mas more in the nature of a physical than a chemical one. The weight of evidence in recent years is mostly in the direction of ascension rather than lateral secretion; and one of the strongest evidences is the fact that most of the ore-bodies lie under one of the comparatively impervious layers which help to make up the structure of these hills.

Jan 1, 1911

By C. W. Thompson

The two-way belt conveyor for coal mine service simultaneously carries coal from faces and transports men and supplies into the mine, largely eliminating the necessity for rubber-tired supply and man haulage equipment and the necessity of maintaining additional headings. SINCE 1920 use of belt conveyor transportation has increased steadily, and capacity in tons per hour per unit has increased at about the same ratio. Belt conveyor systems for simultaneous two-way material transportation have been widely discussed, but heretofore have proved impractical for specific operations. Studies of a proposed means of disposing of wash-ery waste on the return trip of a main haulage conveyor, as yet uninstalled, led to the application of two-way belt haulage to Weirton's underground supply and mantrip problems. Except for a single-tracked main haulage entry, Weirton mine is essentially a full-belt haulage operation with attendant problems of supply and man-trip haulage that could not be handled with conventional belt conveyors during the regular work shift. It was necessary, therefore, to maintain rubber-tired haulage equipment and haulageways serving multiple-shift continuous operations. The conventional underground belt conveyor is primarily intended to transport coal from working faces to surface. Belts are usually reversed to haul men to face areas at the start of the working shift or to transport supplies. The two-way belt conveyor for coal mine service is not yet offered for sale as a unit by any manufacturer and must be built on order. This conveyor, with return run traveling parallel but opposite in direction to the outgoing or coal haulage run, permits not only haulage of coal from faces, but simultaneously permits transportation of men and supplies into the mine at any time, see Figs. 1 and 2. This eliminates, to a great extent, the necessity for rubber-tired supply and man haulage equipment and the maintenance of additional headings. Unlike conventional installations the return belt is in the open for inspection and maintenance. It is less subject to edge wear, since it runs on regular troughing idlers, see Fig. 3. The only points where the edge of the belt can rub are at the drive unit and the tail units where improved design should eventually eliminate edge wear entirely. Individual conveyor sections are lighter, since all that is needed is a tubular stringer on each side to carry troughing idlers only, no cover plates being necessary. The return run is carried on an assembly identical to that carrying the coal haulage run. These assemblies are definitely easier to handle and are cheaper than installations for the same length of conventional belt conveyor. The four pipes required for the complete conveyor frame may serve only as supports, or, with proper couplings, may be used for mine water discharge line, pressure line for face spraying, telephone cable conduit, or any other purpose requiring a pipe line, see Fig. 4. Additional expense, if any, for the increased number of pulleys needed to turn the belt over for the return service is more than offset by reduced expense for rubber-tired supply and mantrip haulage. The two-way belt haulage system is confined to a single heading on intake air, isolated from all other headings by stoppings on each side, and open for air circulation only at the main haulage way and at the faces. One additional heading, also on intake air, is maintained as an emergency rubber-tired haulage way, all other headings being center-posted and used as airways only until retreat work begins. This method, of course, can and should be used with any belt conveyor, since it provides two independent intake airways for escape in case of fire on the belt or elsewhere. Belt heading is heavily timbered even under good top conditions and space between the two runs permits center posting for the full length

Jan 1, 1954

By John S. Brock

INTRODUCTION The Oxford Dictionary says that the word "promoter" has usually been used in an opprobrious sense since at least 1876. This popular image of mining promoters is of cigar-chomping shysters and Brooklyn-Bridge vendors, improving their standard of living with the aid of funds raised through the sale of stock to little old ladies. It is unfortunate that mining promoters are considered crooks until they can prove their integrity and honesty by finding a mine. A common rule of thumb states that for every 1,000 prospects, 100 come to be drilled, and one becomes a mine. However, it is also a statistic that there have been mining promotions, where money raised has gone elsewhere than into the ground; Junior exploration companies can be handy vehicles for unscrupulous financial activity. One must remember though that every stock exchange has had its share of sound mining promotions that, because of the one in 1,000 odds, have failed for legitimate reasons. The promoter must be able to rationalize the worth of a mineral discovery which, on an industry- average basis, probably cost more to find than the discounted value of its net return, which return is not an assured percentage of invested capital, and furthermore, is ultimately from a wasting asset. So, it is easy to understand why the promoter must constantly justify the credibility of his operation to his grubstakers during the course of the "five phases of exploration," those being (1) euphoria, (2) disillusionment, (3) search for the guilty, (4) punishment for the innocent, and (5) distinction for the uninvolved. The promoter with the exploration organization that does not have the benefit of positive cash flow, by definition for the sake of this article, works for a promotional outfit, a Junior Company, that must raise its exploration budget from a variety of sources. Promotion, as discussed here, will not entirely refer to the formation and operation of a joint- stock company but rather to the overall methods of raising risk capital for mineral exploration ventures from outside sources. THE NECESSITY OF PROMOTION In Canada, the publicly financed Junior Company has had an enviable record of mine-finding success. In the Province of British Columbia alone, the discovery of fifteen out of twenty-four mines has been as a result of the activity of the Junior Company (B. C. & Yukon Chamber of Mines, 1977). In the Province of Ontario, one research study indicated that between 1951 and 1974 the 'Juniors' spent only 28 percent of the total exploration funds but were responsible for 62 percent of all economic discoveries (Freyman, 1978). The reasons for the success of the Juniors are tied to a variety of factors, the main one being personal initiative based on incentive. In other words, the principals, or their employees have 'a piece of the action.' The smaller companies can operate faster and more efficiently than their larger counterparts. The Junior Company is also destined to take some bigger risks, the 'long shots,' many of which efforts by virtue of the Junior's perseverance coupled with a touch of 'ore is where you find it' philosophy, result in major discoveries. The individuals, syndicates, private and publicly financed Junior Companies, because of high costs of exploration and development, cannot hope to finance most mineral prospects all the way to production. Exceptions do exist, those being the lower capital cost, small, high-grade deposits. Private investors and publicly financed Junior companies, therefore, can usually afford to finance most exploration through the initial drill-testing stage. The major resource company will enter a mining deal with a Junior Company usually by way of option or joint venture agreement, and will finance to production to earn an equity in the prospect or the Junior Company or both. The conventional lending institutions, banks and government agencies, will usually only participate through loaning a portion of capital

Jan 1, 1985

By R. A. Ronzio, P. B. Queneau, C. A. Born

The molybdenite flotation operation of Climax Molybdenum Co., Division of AMAX Inc., near Leadville, Colo., generates a rougher tailing containing 0.03% W03 and 0.005% SnO2. This tailing is subjected to a series of mineral beneficiation steps for production of wolframite and cassiterite concentrates. However, these byproducts are contaminated by small quantities of UsOa. This paper describes application of sulfuric acid-sodium chlorate leaching for substantial elimination of the radioactive impurities, particularly the mineral brannerite. The leached residue is amenable to magnetic separation of wolframite from cassiterite.

Jan 1, 1976

By J. L. Carne

ORE control is a matter of planning and supervision based on a foreknowledge of the content and distribution of ore. The Inspiration orebody is predominately a copper-sulphide blanket, overlain by an oxidized zone of copper silicates, copper carbonates, and barren capping. Most of the ore is treated by leaching, and the optimum requirement of this method is the goal toward which the mining schedule is aimed. Both open-pit operations and underground mining are used. The problems of ore control at Inspiration are: I—maintenance of metallurgical balance, 2—conservation of oxide ore, and 3—mining out of the orebody at an average grade which parallels that of the reserve figure. Prior to the fall of 1926 all of the Inspiration division ores were treated by flotation, but the mixed ores of the Live Oak—Keystone section carried too large a proportion of copper in the form of chrysocolla for satisfactory flotation. For this type of mixed ore the leaching process now in use had been worked out, and the plant was put into operation in the fall of 1926. The process is known as the ferric sulphate leach, and the leaching solvents contain both ferric sulphate and free sulphuric acid. Sulphide copper in the form of chalcocite is leached by the ferric sulphate, and the oxidized copper minerals are dissolved by the sulphuric acid. From the beginning of operations to the present time the plant has treated some 67 thousand tons of ore having an average copper content of 1.142 pct, of which 0.605 pct has been in the form of oxidized copper minerals. The plant is currently being operated at the rate of 11,500 tons per day, 7 days per week. However, this tonnage is produced in 6 days of mine operation. The average current grade is approximately 1 pct copper, of which about 50 pct is present as oxidized or acid-soluble copper. Close control of metallurgical procedures is a vital factor in operation of the plant and is in turn dependent upon careful regulation of feed. An excess of sulphide copper requires the presence of more ferric sulphate in the leaching solvents. On the other hand, an excess of ferric sulphate in the presence of a low sulphide feed seriously reduces the efficiency of electrolytic precipitation in tank house operations. This condition must be avoided at all costs. An additional factor must be considered. It is known that the sulphide content is predominant in the ore which remains in the reserve. To maintain the necessary sulphide-oxide proportion, so that the entire reserve will mine out at both a grade and a sulphide-oxide ratio that will be permissible throughout the remaining life of the property, it is obvious that the oxide reserve must be currently preserved to as great an extent as possible. Fortunately much of the oxide reserve is found in the open-pit operation. This happy circumstance adds flexibility to the procedure and makes it possible to maintain the close regulation necessary to insure best overall results, both mining and metallurgical. The two ore streams from the pit and underground operations join at the coarse-crushing plant, and proper control must be exercised before the ore reaches this point. The open pit is currently providing about 55 pct of the ore and underground operations the balance of production. Both operations are under a single superintendent so that the closely interrelated problems may be more readily controlled. The least flexible of the two producing units is the underground mine, where the mining method is block caving. Although a block of ground may be undercut and developed, characteristics of the material determine its caving action. The ore in the chutes must be drawn. The area currently mined from underground is in a zone predominately sulphide and is generally

Jan 1, 1953

By J. L. Carne

ORE control is a matter of planning and supervision based on a foreknowledge of the content and distribution of ore. The Inspiration orebody is predominately a copper-sulphide blanket, overlain by an oxidized zone of copper silicates, copper carbonates, and barren capping. Most of the ore is treated by leaching, and the optimum requirement of this method is the goal toward which the mining schedule is aimed. Both open-pit operations and underground mining are used. The problems of ore control at Inspiration are: I—maintenance of metallurgical balance, 2—conservation of oxide ore, and 3—mining out of the orebody at an average grade which parallels that of the reserve figure. Prior to the fall of 1926 all of the Inspiration division ores were treated by flotation, but the mixed ores of the Live Oak—Keystone section carried too large a proportion of copper in the form of chrysocolla for satisfactory flotation. For this type of mixed ore the leaching process now in use had been worked out, and the plant was put into operation in the fall of 1926. The process is known as the ferric sulphate leach, and the leaching solvents contain both ferric sulphate and free sulphuric acid. Sulphide copper in the form of chalcocite is leached by the ferric sulphate, and the oxidized copper minerals are dissolved by the sulphuric acid. From the beginning of operations to the present time the plant has treated some 67 thousand tons of ore having an average copper content of 1.142 pct, of which 0.605 pct has been in the form of oxidized copper minerals. The plant is currently being operated at the rate of 11,500 tons per day, 7 days per week. However, this tonnage is produced in 6 days of mine operation. The average current grade is approximately 1 pct copper, of which about 50 pct is present as oxidized or acid-soluble copper. Close control of metallurgical procedures is a vital factor in operation of the plant and is in turn dependent upon careful regulation of feed. An excess of sulphide copper requires the presence of more ferric sulphate in the leaching solvents. On the other hand, an excess of ferric sulphate in the presence of a low sulphide feed seriously reduces the efficiency of electrolytic precipitation in tank house operations. This condition must be avoided at all costs. An additional factor must be considered. It is known that the sulphide content is predominant in the ore which remains in the reserve. To maintain the necessary sulphide-oxide proportion, so that the entire reserve will mine out at both a grade and a sulphide-oxide ratio that will be permissible throughout the remaining life of the property, it is obvious that the oxide reserve must be currently preserved to as great an extent as possible. Fortunately much of the oxide reserve is found in the open-pit operation. This happy circumstance adds flexibility to the procedure and makes it possible to maintain the close regulation necessary to insure best overall results, both mining and metallurgical. The two ore streams from the pit and underground operations join at the coarse-crushing plant, and proper control must be exercised before the ore reaches this point. The open pit is currently providing about 55 pct of the ore and underground operations the balance of production. Both operations are under a single superintendent so that the closely interrelated problems may be more readily controlled. The least flexible of the two producing units is the underground mine, where the mining method is block caving. Although a block of ground may be undercut and developed, characteristics of the material determine its caving action. The ore in the chutes must be drawn. The area currently mined from underground is in a zone predominately sulphide and is generally

Jan 1, 1953

By P. E. Arnold, G. S. Ansell

RELAXATION in metals has been studied in detail by many workers in recent years.1-5 These studies have shown that there is an energy-loss peak observed in a metal placed in mechanical resonance at low frequencies which may be correlated with various metallurgical processes. These experiments have been largely used to study single-phase materials. In order to study the effect of a finely dispersed second phase in a metal matrix upon this phenomenon, the relaxation behavior of an aluminum-aluminum oxide SAP-Type alloy in both the fine-grained as-extruded and coarse-grained recrystallized conditions was investigated by the use of internal-friction measurements. The alloys studied, designated MD 2100, consist of a matrix of commercial-purity aluminum containing a finely dispersed second phase of aluminum oxide. The aluminum oxide is present in this alloy in the form of fine platelets approximately 130A units thick and several microns on edge. The mean free path betwen dispersed platelets is approximately 0.5 p. The grain size of this alloy is extremely stable at temperatures as high as the melting temperature of the aluminum matrix. In the as-extruded condition the grain diameter is several microns, while in the recrystallized condition it is several millimeters in diameter. The damping characteristics of the alloy samples were determined using a torsional-pendulum device. The internal-friction constant was determined for this alloy in both the fine-grained as-extruded and coarse-grained recrystallized conditions over the temperature range from 343" to 923°K at frequencies of 0.9, 1.3, and 1.8 cycles per sec. An internal-friction peak was observed in testing the fine-grained alloys which was not observed for the coarse-grained alloys. This peak, which might be associated with a type of grain-boundary relaxation, was observed at each of the three different test frequencies for the fine-grained sample. The temperature at which the relaxation peak occurred for each of the three different frequencies is shown in Table I. From these data an activation energy of relaxation for each pair of frequencies was determined by comparing the temperature shift of the relaxation peak with frequency between each of the test frequencies, assuming that an Arrhenius-type rate equation is applicable. The activation energy of relaxation determined from these data is also shown in Table I. The mean value of the activation energy was about 6 kcal per mole. The activation energy for the relaxation process determined in this investigation indicates that the relaxation associated with the grain boundaries in this aluminum-aluminum oxide SAP-Type alloy is quite a different process than grain boundary relaxation in single-phase aluminum alloys. In these latter alloys, the activation energy for relaxation has been found to be the activation energy for self-diffusion, approximately 36 kcal per mole1,2 Where the activation energy is the same as the activation energy for self diffusion, it has been proposed that the relaxation phenomena is dependent upon vacancy formation and motion. It is apparent therefore, that, in this aluminum-aluminum oxide SAP-Type alloy, the relaxation must be due to another type of atom transport. It has been shown previously in studies of the high-temperature, low-stress, steady-state creep behavior of as-extruded aluminum SAP-Type alloys, that the activation energy for steady-state creep is one that may be characterized by the nucleation of dislocations from the grain boundaries. It is proposed that the relaxation behavior observed here is due to a similar effect. In this case, the internal-friction peak is a resonance behavior due to the time-dependent nucleation of dislocations from grain boundaries in the sample. A process of this type would have an activation energy which is undoubtedly stress-dependent and of the form Q = Q, + (dQ/du)u

Jan 1, 1962

By A. L. Lee, M. H. Gonzalez, R. F. Bukacek

Experimental viscosity data for methane are presented for temperatures from 100 to 340F and pressures from 200 to 8,000 psia. A summary is given of the available data for methane, and a comparison is presented for that data common to the experimental range reported in this paper. Correlation of the data is presented, and predicted values are given for temperatures up to 460F and pressures up to 10,000 psia. INTRODUCTION The increasing ranges of temperature and pressure at which fluids are produced, transferred and processed in the petroleum and chemical industries stress the need for accurate information on physical properties, both for engineering calculation and for improving the methods used to estimate physical properties. A survey of the literature reveals that disagreements between published data on the viscosity of methane are common and that most investigations have been conducted over restricted temperature and pressure ranges. This situation made it desirable to undertake an investigation with a scope common to most of the literature data available. APPARATUS AND MATERIALS The apparatus used in this investigation was the capillary tube viscometer'described by Dolan,10 with modifications introduced in the general design and operation of the instrument. It has an effective pressure range from 14.7 to 10,000 psia and a temperature range from room temperature to 400F. The design of the viscometer is based on the establishment of a manometric head between two vessels containing the test fluid and a volume of mercury. The reservoirs are connected by a capillary tube through which the test fluid flows and a tube through which mercury flows. A pressure gradient is established by elevating one of the vessels above the other, the resulting flow of mercury displacing the test fluid through the capillary. The schematic diagram of the system (Fig. 1) shows the arrangement of the equipment auxiliary to the viscometer. The density cells assembly (E, Fig. 1) was not used in this investigation since reliable data are available on methane. 23 The assembly consists of a bank of eight 316 stainless steel pycnometers. Experimental values of the density of a natural gas19 and i-butane14 samples have been obtained for pressures up to 8,000 psia and temperatures up to 340F. The methane used was obtained from the Southern California Gas Co. Mass spectrometric analysis showed a composition of 99.8 percent CH4, 0.1 percent C2H6 and 0.1 percent C3H8. EXPERIMENTAL VALUES AND ACCURACY OF DATA Determinations were carried out at several temperatures. With the temperature in the cabinet controlled at a given level, a series of runs were made at various pressures. To establish pressures lower than that obtained from the methane cylinder, it was necessary to vent the gas slowly to the atmosphere until the desired pressure was reached. The consistency of the test run time for a particular condition can be used as a criterion for the accuracy of the data. A further check is obtained by comparison of the viscosity values obtained using different driving heads. To establish the instrument's reproducibility, a large number of runs were made at three completely different conditions of temperature and pressure. Data obtained were analyzed statistically to determine the most reliable value for the variance of the experimental data. It was found that the variances of the data taken at different experimental conditions were not statistically equivalent, but they were small. The largest variance was found at 8,000 psia and 100F, where the standard deviation was 0.385 micropoise. Therefore, 99.9 percent of the data can be expected to fall within 1.15 micropoises of the population mean, except for the intervention of systematic errors in operation.

By C. L. Pillar

INTRODUCTION The location, size, character of the ore de- posit and its adjacent formations will deter- mine the mining system best used for its ex- traction. The mining system chosen will have to be engineered to suit the ore deposit and the people that will extract it. What can be done in the Philippines cannot always be accomplished in the upper Northwest Territory of Canada. Mining operations developed under a free enterprise system are planned to achieve a satisfactory return on the capital required to place them into production. Hence, the choices made in planning and developing the mining system must be dictated by sound economics. The mining system planned must favor: 1. Maximum ore extraction of the deposit with minimal grade dilution. 2. The amount of capital expenditure used to develop and equip the mine must be in harmony with the financial policy of the group yet be sufficient to provide a reliable mining system. Excessive frills and extras that are not required for efficient, safe production should not be provided. 3. Mine production costs are determined by the amount of men, material, equipment and energy used in the production process. These must be kept to minimal limits in order to insure dependable, low cost production. Extras that later are needed in the production operation can be added as required by the operator. Basically block caving is a mining system that is normally used to extract deep seated, massive, low grade deposits of copper, molybdenum and iron where stripping ratios for open cast mining are economically prohibited. The caving system is limited in its selectivity. It is a mass production type of underground ore extraction that under favorable conditions is one of the most efficient, low cost mining systems in the world today. Usually block cave mining systems are large. They are capable of producing ore at a rate of 10,000 to 100,000 tons/day from large deposits at costs that are comparable with many open cast mining systems burdened by high waste to ore ratios. Block cave mining systems differ basically in the plan of the area layout, the method of undercutting and the method of draw. The balance of the mining system is the mechanical transportation of the drawn ore to the surface, the mine supply, drainage and ventilation systems. This paper deals mainly with the methods of draw. The method of draw to be used in a block caving system dictates the development plan of the mining area, is highly influential in the method of undercutting to be employed and the supply and ventilation system to be used. There are three basic methods of draw commonly used in today's operations. They are: Gravity draw Slusher draw LHD draw The type of draw planned will have a major affect on: Capital expenditure and time required to bring a deposit into production. Productivity, efficiency and cost of the production operation. Percent recovery of the ore deposit in both tonnage and grade. Degree of production reliability Fundamentally the type-of draw used must be compatible with the physical characteristics of the deposit to be extracted and the financial position of the mining operation. The type of draw chosen must work to advantage with the size, configuration, depth, strength and fracture pattern of the deposit and its adjacent formations. It must favor the financial protection of the planned mining operation. A Gravity Method of Draw requires a finely fragmented, easy flowing product from the caving action of the deposit. To obtain the desired economic advantage the ore deposit must also have sufficient area and height of column to permit minimal development cost on a per ton basis. The gravity system re- quires the maximum amount of development openings and uses the minimum amount of mechanized equipment of all the caving systems. It is unskilled, labor-intensive and is highly sensitive to size of ore fragmen-

Jan 1, 1981

By Jack White

MUFULIRA Copper Mines, Limited, conducted tests on the concentrator in 1942 to determine which type of ball mill, that is, Conical Trunnion overflow or Cylindrical Grate discharge, produced the greater quantity of finished product at the lowest cost. All the data which follows applies to Mufulira ore and to the particular degree of grinding produced with the classifiers installed at Mufulira concentrator. JACK WHITE, Member AIME, is Concentrator Superzntendent, Mufulira Copper Mines, Ltd., Mufulira, Nortltern Rhodesia. Sun Francisco Meeting, February 1949. TP 2729 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Feb. 28, 1949. Test Procedure: The test was carried out using ball mills No. 1 to 9 (conical trunnion overflow) as the standard with which to compare No. 10 (cylindrical grate discharge mill). The conical trunnion overflow ball mills are 10 ft diam by 72 in., and the cylindrical grate discharge mill is a No. 99. Each mill runs in closed circuit with a Dorr type DSFX classifier 8 ft wide by 30 ft long. The feed is considered as being identical to all ten units. The figures for the test were derived as follows. Dry Tons Milled: For No. 10 unit (cylindrical grate discharge mill) this figure was taken from the ball mill weightometer, which was corrected for error, and then for moisture content. The weightorneter was checked twice a week during the test, and the error did not exceed 3 pct at any time. The moisture was obtained from a 24 hr moisture sample taken by the ball mill operator hourly, and placed in a closed bucket. The sample was cut where the conveyor drops the feed into the ball mill chute. The Mill Sampling Department made a daily moisture determination on this sample. To obtain the dry tons on units No. 1 to 9 the No. 10 figure was deducted from the month's dry tons milled figure, which, in turn, was taken from the crusher weightometer tons corrected for weightometer error and moisture. All tons reported in this test are short tons of 2000 lb. Ball Mill Hours: This was taken daily from the Shift Boss reports giving actual running hours for each unit. Screen Analyses: Coarse Heads (Ball Mill Feed): The monthly composite coarse heads screen analysis, done by the Mill Sampling Department, was used for the minus 200 mesh in the feed to the mills. F. X. Classifier Overflow: The ball mill operators took an hourly 24 hr sample of the overflows of units No. 1 to 9. This was a hand sample, but cut with a special cutter, and is believed to be very reliable. On No. 10 unit, an hourly 24 hr sample, and an hourly shift sample were cut in the same way. These five samples were split, filtered, and dried by the Research Department and were then wet screened on a 200 mesh screen. The average of the three shifts samples on No. 10 unit had to check the 24 hr sample within 1.5 pct to be acceptable. A weighted composite was cut each day from both 24 hr samples, and at the end of each month it was screened as follows: Wet screened through 325 mesh, the plus 325 then screened on a rotap for 15 min through 65, 100, 150, 200, and 325. This was done in duplicate. All splitting, drying, and screening of samples was done by one of the Mill Research staff, to insure accuracy. F. X. Classifier Overflow Densities: These were taken from the Shift Boss reports. Densities were taken by the ball mill operator every hour. Circulating Loads: These were taken a number of times during the test both by direct method (weighing a measured portion of classifier rake sand, and deducting moisture) and by calculation using the formula:

Jan 1, 1951

By Jack White

MUFULIRA Copper Mines, Limited, conducted tests on the concentrator in 1942 to determine which type of ball mill, that is, Conical Trunnion overflow or Cylindrical Grate discharge, produced the greater quantity of finished product at the lowest cost. All the data which follows applies to Mufulira ore and to the particular degree of grinding produced with the classifiers installed at Mufulira concentrator. JACK WHITE, Member AIME, is Concentrator Superzntendent, Mufulira Copper Mines, Ltd., Mufulira, Nortltern Rhodesia. Sun Francisco Meeting, February 1949. TP 2729 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Feb. 28, 1949. Test Procedure: The test was carried out using ball mills No. 1 to 9 (conical trunnion overflow) as the standard with which to compare No. 10 (cylindrical grate discharge mill). The conical trunnion overflow ball mills are 10 ft diam by 72 in., and the cylindrical grate discharge mill is a No. 99. Each mill runs in closed circuit with a Dorr type DSFX classifier 8 ft wide by 30 ft long. The feed is considered as being identical to all ten units. The figures for the test were derived as follows. Dry Tons Milled: For No. 10 unit (cylindrical grate discharge mill) this figure was taken from the ball mill weightometer, which was corrected for error, and then for moisture content. The weightorneter was checked twice a week during the test, and the error did not exceed 3 pct at any time. The moisture was obtained from a 24 hr moisture sample taken by the ball mill operator hourly, and placed in a closed bucket. The sample was cut where the conveyor drops the feed into the ball mill chute. The Mill Sampling Department made a daily moisture determination on this sample. To obtain the dry tons on units No. 1 to 9 the No. 10 figure was deducted from the month's dry tons milled figure, which, in turn, was taken from the crusher weightometer tons corrected for weightometer error and moisture. All tons reported in this test are short tons of 2000 lb. Ball Mill Hours: This was taken daily from the Shift Boss reports giving actual running hours for each unit. Screen Analyses: Coarse Heads (Ball Mill Feed): The monthly composite coarse heads screen analysis, done by the Mill Sampling Department, was used for the minus 200 mesh in the feed to the mills. F. X. Classifier Overflow: The ball mill operators took an hourly 24 hr sample of the overflows of units No. 1 to 9. This was a hand sample, but cut with a special cutter, and is believed to be very reliable. On No. 10 unit, an hourly 24 hr sample, and an hourly shift sample were cut in the same way. These five samples were split, filtered, and dried by the Research Department and were then wet screened on a 200 mesh screen. The average of the three shifts samples on No. 10 unit had to check the 24 hr sample within 1.5 pct to be acceptable. A weighted composite was cut each day from both 24 hr samples, and at the end of each month it was screened as follows: Wet screened through 325 mesh, the plus 325 then screened on a rotap for 15 min through 65, 100, 150, 200, and 325. This was done in duplicate. All splitting, drying, and screening of samples was done by one of the Mill Research staff, to insure accuracy. F. X. Classifier Overflow Densities: These were taken from the Shift Boss reports. Densities were taken by the ball mill operator every hour. Circulating Loads: These were taken a number of times during the test both by direct method (weighing a measured portion of classifier rake sand, and deducting moisture) and by calculation using the formula:

Jan 1, 1951

By William E. Souder, Eugene R. Palowitch

INTRODUCTION The longwall method of mining coal underground is now a highly developed and accepted mining technology. However, it was only through a long history of successes and failures that this technology now has the potential for reversing the declining trend in underground mining productivity in the United States. From its early beginnings in the United States during the 1800's, several species of longwalls have evolved. The evolutionary record consists of a series of overlapping birth-death eras, with each era giving way to another unique longwall technology. Typically, an era begins when some new longwall technology appears in response to a new technical opportunity or economic need. This new technology is adopted initially by only a few innovators. Later, other imitators get on the bandwagon and the technology diffuses throughout the user population. But evolving technical demands and socio-economic circumstances eventually cause many of the adopters to discontinue its use. This paper chronicles seven eras in the history of the evolution and utilization of longwall technologies in the United States. Some of the important factors that have influenced this history are discussed. Some distinctions are drawn between the operators who were first to adopt longwalls (innovators), and the imitators who followed. Statistics are presented which show that longwall mining is being adopted at an exponentially increasing rate, substantiating the forecast for a significant number of new longwall installations in' the future. Potential barriers to this increased utilization of long- walls are noted.

Jan 1, 1981