Search Documents

By D. R. Miller

The use of fully grouted cables for ground reinforcement in underground mining is becoming widespread. Reinforcement design for this application has tended to be empirical although some two- dimensional design techniques have been developed. This paper describes a technique based on a model of the behaviour of cables placed across planes moving in shear. The model is three- dimensional and includes a simple model of the 'dowel' effect which arises from the bending of the cables. The model determines the shear resistance developed at a particular shear displacement assuming joint friction and cable parameters. Using data for twin 15.2mm dim. steel strand cables, and a concept of reinforcement efficiency, the application of the model to design wall support in open stopes is demonstrated. The examples consider the cases where major planar structures are known in location and orientation and where, as is more common is open stope development, mapping has indicated that a distribution of potential shear failure structures may be present. The actual location and orientation of potential shear planes is not known. These two cases highlight the underdesign of reinforcement that may arise if the distribution of orientation of potential shear planes is not considered.

Jan 1, 1984

By Theodore B. Comstock

The existing topographical features of the United States present many points of interest to the student of dynamical geology, but there is, perhaps, no subject which offers a more promising field for investigation than the relations between the geological structure and the mineralogical characteristics of the principal mining districts. There are seven prominent culminating points in the relief of North America, each one of which can be used as a type of the physical features of all the others. Again, if we divide these seven elevated districts into two sets, we shall discover a still more striking parallelism between the individual members of each group. But the most remarkable revelation is the fact that each one of these points is more or less closely the centre of an area of economically important mineral resources. It is interesting to note in this connection that six of these mineral tracts lie mainly within the borders of the United States, three of them being almost wholly in our territory. For

Jan 1, 1883

By Arthur C. Spencer

The object of the following paper is a description of the Treadwell gold-deposits in their geological aspects. quite apart from any consideration of the economical methods of mining and milling which have been developed and successfully applied

Jan 1, 1905

By G. W. Tracy, R. D. Carter

A method based on an approach by Hurst' is developed for calculating water influx behavior. Using this method, superposition calculations may be eliminated. The principal diflerence between this method and that of Hurst is that, over finite intervals of time, constant oil-productton rates are assumed by Hurst whereas constant water influx rates are assumed in the presently described method. By adopting the assumption of constant water influx rate for finite time periods, a method is developed for calculating water influx behavior which lends itself to convenient combination with the material balance equation in the Schilthuis form. Above the bubble point, an equation is given for the explicit step-wise calculation of pressure history for a prescribed oil-production history. Use of this method of calculating water influx behavior should result in a considerable saving of time as compared to superposition calculations when the calculations must be made without using a digital computer. The connection is shown between the method described herein and the method developed by van Ever-dingen and Hursr2 (which requires superposition cal-culations). Also, results obtained using the two methods are compared.

By C. A. Mitke

In the Southwest, mcchanical ventilation of metal mines has been receiving consideration for many years. The United Verde Copper Co., in Jerome, has used large mine fans for ventilation and fire-fighting purposes for at lcast 15 years, while the Copper Qucen Branch of the Phelps Dodge Corpn. commenced installing mechanical ventilation in its various divisions 10 years ago.' Since then, with few exceptions, every large mine in this part of the country has installed and put in operation a mechanical ventilating system. The properties of some of these companies consist of from two to six divisions, or separate mines, each of which requires an independent ventilating system. In other words, thirteen copper mining companies, with an aggregate tonnage, when operating at capacity, of approximately 50,000 tons a day, have installed mechanical ventilating systems in their mines. All these mines are within a radius of approximately 200 miles, which constitutes the largest copper-producing area in the world. The capacities of mechanical ventilating installations in these mines range from 100,000 to 300,000 cu. ft. of air per minute, depending on the size of the mine, character of the workings, tonnage produced, etc. The latter varies from 300 to 20,000 tons per day. The mines include both high- and low-grade deposits, the greatest depth of the former, at present, being approximately 2500 ft.; and of the latter, 1200 ft. The volumes of air at present being coursed through the mines are from 60,000 up to 225,000 cu. ft. of air per minute,which, in their relation to the undcrground working force, range from 200 to 800 cu. ft. of air per man, per minute. While not to be taken as criteria, these figures are indicative of the character of the ventilation furnished.

Jan 1, 1923

By C. A. Mitke

In the Southwest, mcchanical ventilation of metal mines has been receiving consideration for many years. The United Verde Copper Co., in Jerome, has used large mine fans for ventilation and fire-fighting purposes for at lcast 15 years, while the Copper Qucen Branch of the Phelps Dodge Corpn. commenced installing mechanical ventilation in its various divisions 10 years ago.' Since then, with few exceptions, every large mine in this part of the country has installed and put in operation a mechanical ventilating system. The properties of some of these companies consist of from two to six divisions, or separate mines, each of which requires an independent ventilating system. In other words, thirteen copper mining companies, with an aggregate tonnage, when operating at capacity, of approximately 50,000 tons a day, have installed mechanical ventilating systems in their mines. All these mines are within a radius of approximately 200 miles, which constitutes the largest copper-producing area in the world. The capacities of mechanical ventilating installations in these mines range from 100,000 to 300,000 cu. ft. of air per minute, depending on the size of the mine, character of the workings, tonnage produced, etc. The latter varies from 300 to 20,000 tons per day. The mines include both high- and low-grade deposits, the greatest depth of the former, at present, being approximately 2500 ft.; and of the latter, 1200 ft. The volumes of air at present being coursed through the mines are from 60,000 up to 225,000 cu. ft. of air per minute,which, in their relation to the undcrground working force, range from 200 to 800 cu. ft. of air per man, per minute. While not to be taken as criteria, these figures are indicative of the character of the ventilation furnished.

Jan 1, 1923

By Henry M. Howe

In discussing the classification of iron to-day, we are to leave out of consideration the general division into non-malleable or cast iron and malleable iron, as to the adequacy of which no question has been raised; and to confine ourselves to the subdivisions of malleable iron. This has been classified, according to the extent to which the properties imparted by carbon are present (viz., resilience, hardness,strength, and, above all, the capacity for being hardened by sudden cooling from a high temperature), into (1) wrought iron which cannot be hardened, and (2) steel which can be hardened; and this classification I shall, for briefness, term the carbon classification. Until within a few years all authorities, both metallurgical and general, have concurred in explicitly recognizing the carbon-given qualities, and preeminently the capacity for being hardened, as the essential qualities of steel; this is laid down with clearness by every writer on the subject. For several years this old classification has not been sufficient to meet all our needs, since the genius of Bessemer, Siemens, and, I may add, Holley, has produced wrought iron which has been perfectly melted, and thus freed from certain mechanical adhering impurities. This causes what we call homogeneousness for want of a better word, and gives rise to many important qualities which the old wrought iron had not; qualities universally recognized, though not readily described. I shall, for briefness, style them the fusion qualities, and a classification based on them, a fusion classification. These qualities render the new product so vastly superior, for most purposes, to the wrought iron formerly known, that it is neces-

By Paul Sterling

The general impression regarding the preparation of merchantable anthracite is that it is confined to a colossal, grimy structure, called a " coal-breaker." This name is a misnomer; for the desired result is not to break the coal, but to prevent its being broken. Preparation may be said to begin at the face of the chamber, with the mining and loading of the coal. Local conditions vary, not only ill the same field or basin, but also in the same mine, so that there is no fixed empirical rule governing the method of blasting or cutting coal. Tests should be made, when possible, to determine the explosive, or the mechanical coal-cutter, which will produce the largest percentage of what are locally known as " lump " and " prepared sizes " of anthracite. The prepared sizes are those mostly consumed for clomestic purposes. All other sizes might be called by-products of the anthracite industry; for they are not especially desirable, being the degradation resulting from the mining and handling of a brittle or laminated material. Being low in volatile combustible matter, anthracite burns most successfully when nearly of a uniform size, permitting the easy passage of air through the voids. This accounts for the large number of sizes into which the coal is separated. Table I. gives the various sizes, the diameter of ring over and through which each size is made, and the usual purpose for which it is employed.

Jan 1, 1912

By Herbert Haas

GEORGE W. HAWKINS, Tucson, Ariz. (communication to the Secretary*).-The paper by Mr. Haas will no doubt be followed with considerable interest, as it covers the power-plant problem in quite a comprehensive way, including not only the usual operating costs but also the fixed charges on the investment, and for load factors ranging all the way from 25 to 100 per cent. and fuel oil ranging from $1.25 to $2 per barrel. The very fact, however, that his paper does cover such a wide range of conditions, makes it the more imperative that any conclusion drawn from his analysis be very carefully considered for any specific case, for in making such analysis the type of prime mover and size must be selected for some one condition which might not be the proper selection had some other condition been assumed as the basic one, resulting in an unfavorable comparison under all conditions except that condition assumed. From the reasons given by the author for his selection of the large turbine units, it is evident he had in mind very high load factors, ranging

Jan 12, 1916

By W. Kennedy

THROUGHOUT northeastern Texas we have an extensive series of iron-ore deposits, occupying portions of nineteen counties and having approximately an actual ore-covered area of 1000 square miles. The existence of these ores has long been known. Kennedy* says: "Iron-ore is distributed in profusion throughout Texas, being found almost everywhere except in the level region of the coast." Before this, C. Newell† had mentioned the existence of these ores thus: " Iron is found in abundance in the eastern, northern and middle portions of Texas;" and in 1849 Edward Smith‡ said: " We met with immense hills of iron which were said to be, and appeared to be, of excellent quality, in Cass and Titus counties.. . .. It is well known that Texas abounds with iron of first-rate quality." In 1859, Dr. Shumard? reports that detailed surveys had been made in several counties, and says: " Our labors have demonstrated the important fact that we have a vast iron-region in the eastern part of the state, embracing considerable areas in Cass, Harrison, Rusk, Panola, Smith, San Augustine and Shelby counties. The ore-deposits belong to the Tertiary era and consist chiefly of hematites and limonites, of which there are several varieties. We have also found in this district extensive beds of carbonate of iron." Dr. Shumard gives no very exaggerated description of Cass county§ as it then existed when he says : " Cass county alone is capable of supplying a number of furnaces with an abundance of excellent iron-ore for many years." Of Rusk county he says: "Our de-

Jan 1, 1895

By Joseph Kittredge

AT the time this matter first came up in 1912, the National Malleable and Steel Castings Co. had seven basic-bottom open-hearth furnaces in its plant at Sharon, Pa., using fuel oil, then costing about 2 ½ ¢ per gallon. The fuel was satisfactory but its cost fluctuated widely, therefore the use of pulverized coal, which had been successful in the cement industry and in some metallurgical furnaces, was suggested. After a thorough investigation, and an actual trial on one of the open-hearth furnaces, to be certain that the siliceous ash in the coal would not seriously affect the basic slags, the management of this company approved its adoption and a complete installation was started. The conclusion had been reached that the success of the operation depended on pulveriz-ing the coal to greater fineness than had thus far been accomplished, and all equipment was chosen with this in mind. A coal drier was deemed essential, and one of ample capacity and efficiency was selected, which has done all that was expected of it, working without failure and with very small maintenance cost, and is still in operation.

Jan 1, 1939

By T. S. Spicer, C. C. Wright

A CHARACTERISTIC property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent, but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire The plastic mass prevents uniform distribution of air through the fuel bed and, With strongly coking coals, large dense pieces of coke are produced which have much less reacting surface thin was possessed by the original coal In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued) automatic service In order to burn strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation continuous, intermittent and hold-fire, frequent attention is necessary Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb of coal or less per hour With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel-bed Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals The work of Bituminous Coal Research Inc at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker Typical coke formations in a clinkering type of underfeed domestic stoker are illustrated in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal, (B) the type of fuel bed formed -with, a coal that produces a weal coke, and (C) the type of fuel bed obtained with a strongly coking coal C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is ,burned in an underfeed stoker of conventional type It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals

Jan 1, 1942

By Edward Wichers

THE purpose of this paper is to set forth the matters of principal interest in connection with work done in the past few years on the purification of the metals of the platinum group, including the study and modification of methods already in the literature and the development of new procedures. For the most part, the results will be given in summary form, reserving the publication of detailed data and directions for a forthcoming paper to be issued by the Bureau of Standards. In recent years increasing interest has been shown in the preparation of the pure platinum metals, both by those concerned with the manufacture of the metals and their alloys for scientific and industrial purposes and those who are engaged in the study of the chemical or physical properties of the elements. The purification of the metals usually has been regarded as a matter so involved and difficult as to require the attention of specialists. It is hoped that this paper will show that any of the metals can be prepared in any desired degree of purity by relatively simple straightforward chemical methods. For the most part, it is thought that the methods given are suitable for small-scale refineries as well as for the laboratory; also, that they will bring the time required for the purification of any of the metals within reasonable limits. The new procedure suggested for purifying platinum should prove to be much shorter than any methods described in the literature.

Jan 1, 1928

By Arthur G. Levy, Henry M. How

The purpose of the investigation on which this paper is based is to determine whether the structural change which occurs in the slow cooling of steel below the transformation range has an important effect on its engineering properties. We recognize two distinct things which occur in steel when it is brought from above to below the transformation range, first, the transformation proper, that is, the breaking up of the austenite or solid solution of the cementite in the remainder of the iron, and the liberation of its components as undissolved cementite and as ferrite or alpha iron; and second, a structural change consisting in the gradual coalescence of the ferrite and cementite respectively into larger and larger separate masses. Let us distinguish these from each other by speaking of them as " the transformation " and " the structural change " respectively. If the cooling is at all rapid the unevenness of contraction induces severe stress; so that in a sense a slow cooling has a third influence, the prevention of such stress. This transformation from austenite to ferrite plus cementite can complete itself only below the transformation range; and, because this structural change is a change in the structural arrangement of the products of that transformation, it too can complete itself only at temperatures below that range, say below 725°; and of these temperatures it is only those between 600° and 725° that give the metal sufficient mobility to permit this structural rearrangement to progress with ally rapidity. The transformation is now known to be rapid, but the structural change is relatively slow. The transformation, the liberation of the dissolved cementite from the state of solution in the austenite to a free state, leaves the steel structurally in the

Jan 1, 1913

Jan 1, 1888

By B. Zondek, W. T. Cardwell, J. W. Sheldon

The fundamental equations that are used to describe two-phase fluid flow in porous media are Darcy's law for each phase and an equation of continuity for each component. The special case of one-dimensional, incompressible, two-phase flow has received much attention in the petroleum engineering literature.1-10 The basic paper on the subject is that of Buckley and Leverett.2 Buckley and Leverett showed that one could eliminate the pressure and obtain a single partial differential equation for the saturation. They solved this equation for the case when gravity and capillary forces are negligible. A frequently encountered property of the solution of the basic partial differential equation is that, as time progresses, the saturation becomes a multiple-valued function of the distance coordinate, x. Buckley and Leverett interpreted the formation of multiple values as an indication that the saturation-distance curve had be-come discontinuous. They developed a method of determining the position of the discontinuity from a material balance. We solve the Buckley-Leverett partial differential equation using the method of characteristics and the concept of shocks. Our treatment is analogous to treatments used in the theory of supersonic compressible flow." Although the numerical results obtained are the same as those obtained by previous methods, we believe that this approach is more logical and has broader applicability. It can, for example, be generalized to treat the case when the fluids are compressible. It is not clear how one would go about doing this using the method of Buckley and Leverett. To illustrate the power of the method of characteristics with shocks, we solve a problem in gravity segregation which has not been treated previously in the literature. A special case of the general method developed here was used by Welge, to solve a particular fluid displacement problem. We consider two-phase incompressible flow along the vertical direction x in a porous medium. We assume that there is no flow transverse to .x. We measure positive in the upward direction. The fundamental equations are obtained from Darcy's law and the mass conservation law. Since the two phases are incompressible, mass conservation is equivalent to volume conservation.

By C. F. Cornell, Henderson, A. F. Dunyon, D. A. Dahlstrom

IN processing magnetic taconites several steps of crushing, grinding, classification, and magnetic separation are required to produce a 60+ pct Fe concentrate. Usually the final concentrate is in a slurry form of 55 to 70 pct solids by weight and is further characterized by a particle size of 60+ pct -325 mesh. In taconite plants already completed or under construction the conventional method used to obtain pellets suitable for blast furnaces is to filter the concentrate slurry, ball the filter cake, and then harden the green pellets in a traveling grate or in a vertical shaft furnace. Large tonnages must be handled in minimum floor space, with reduced maintenance and lowest possible operating cost. Filtration must therefore achieve two objectives: 1) high filtration rate-in terms of pounds of dry solids per hour per square foot of filtration area-at a low filtrate solids concentration, and 2) a filter cake moisture that will always permit efficient balling within the normal fluctuations of plant operating conditions. If moisture contents are too high, balling may be impossible or result in a mushy ball without enough green strength for the firing operation.

Jan 3, 1957

By C. H. Brehaut, W. N. Taylor, R. S. Douglas, H. A. Shannon

The name for this new method of mining is derived from a composition of Horizontal, Radial, Diamond, and the drilling is from raises. This method, worked out at Copper Mountain, B.C., is believed to be distinct in many features from other known methods. Geology The ore deposits of copper Mountain are related to the copper Mountain stock, which is an ideal example of the magmatic in in that it grades from a basic gabbro at the border to an almost pure orthoclase-pegmatite core. The "contact" ore bodies lie along the contact of the gabbro and an older complex of volcanies and sediment termed the "Wolfe Creek" formation. These older rocks, collectively referred to as greenstone, had been fractured prior to the intrusion of the stock and were highly metamorphosed during the intrusion. The "outlying" ore bodies are somewhat different in character, though a similar structural pattern prevails. It is believed that a deep-seated magma of which the Copper Mountain stock is a part has given off solutions that caused a partial graniti-zation of some of the volcanies. Mining problems are caused further by the presence of a series of soft barren dikes intersecting a great many of the ore bodies, which are about 30 ft. wide, strike north-south, and dip at a high angle to the east; and are further increased by the presence of four major faults, with a great many minor faults running at acute angles from them. Fault zones average 8 ft. in width, and consist of gouge and breccia. They strike northeast and dip steeply to the northwest. The faults cut through the ore zones and the dikes, and continue on into the gabbro. The general mine structure with two types of Ore bodies, bounded by weak walls and intersected by several series of soft barren dikes and major faults, indicated that a method of mining should be devised that would remove the ore at low cost with the least disturbance of the waste walls and dikes. , Theoretical Estimate of Stoping with the Diamond Drill After consideration of various methods, the most suitable one appeared to be horizontal drilling to break the ore in a manner similar to shrinkage stoping Drilling vertical holes or rings from a bench and breaking to an open slot was eliminated because the weak walls of ore, dike or waste would not permit this type of opening. It was then decided to drill either horizontal radial holes from a raise or parallel holes from a slot cut across the ore body. After discussion, the latter method was believed unsuitable, for the following reasons:

Jan 1, 1946

By Will Mitchell

The classical definition of a beneficiation engineer as one who treats an ore in order to separate and discard worthless fractions by essentially physical means is obsolete. Technology in the profession has advanced so rapidly during the last two or three years that educators have not been able to coin definitions to keep up with the pace. In the past some people have hesitated to include leaching or even agglomeration as minerals beneficiation, because of the major chemical changes involved. This view has fallen by the wayside, especially because a majority in the profession have become actively involved in extraction and pyro processes that go far beyond the original definition of mineral dressing. To say that there is a great revival of interest in leaching is putting it mildly, for the uranium business, like the gold business, now depends almost entirely on leaching. This revival of leaching, long overdue in mineral engineering, has been stimulated this year, especially as a result of the relaxation of security restrictions surrounding the recovery of uranium from its ores. It has brought new unit operations to minerals beneficiation, namely ion exchange and solvent extraction. These operations have appeared as resin-in-pulp, solvent-in-pulp, and liquid-liquid systems. In many cases these leaching and separation procedures, now reaching the production stage, have been engineered by minerals beneficiators. The trend toward leaching has also had impact on the technology of beneficiating other nonferrous minerals, especially copper, manganese, columbium, tantalum, nickel, cobalt, titanium, and the rare earths.

Feb 1, 1956

By C. L. Kinney

The rapid increase in the amount of steel produced by the basic open-hearth process is an index of its ability to produce high-grade steel from raw materials of the most, varied physical character and chemical analysis. This inherent adaptability of the process has resulted in a lack of care in the selection of raw materials, so that in far too many cases charges are used of a chemical and physical character not justified by local economic conditions. A practice, or series of practices, should be used that will result in the greatest economy for the plant as a whole; therefore, the operations of blast furnace and open hearth must be considered together. In this paper, an effort has been made to show those variations in both open-hearth practice and cost that follow changes in the analysis of the pig iron arid it may be said that the theoretical costs shown are worthy of careful study and consideration. Carbon, manganese, silicon, phosphorus, and sulfur constitute the principal metalloids in basic pig iron and play the leading role in the production of steel by the basic open-hearth process. The percentages of each of these metalloids, with the exception of carbon, is a variable that has its genesis in the economic relation of the blast-furnace plant to its ore and fuel supplies. As the amount of carbon in the iron is a saturation function of the temperature at which it is produced, the variation in the amount carried is, for any given locality and grade of iron, practically negligible and is so considered in the eight heats discussed in this paper. The melting and refining reactions in an open-hearth furnace, either acid or basic, are essentially oxidizing and vary greatly with the type and age of the furnace, as well as the character of the fuel employed. The outstanding characteristic of the basic process, and the one that explains its predominance over the acid, is its ability to form out of the lime charged and the phosphorus oxidized from the charge a stable

Jan 1, 1924