Search Documents

By W. H. Newhouse

During the past few years the writer has been impressed by the close relation of many epigenetic orebodies with anticlinal structures. In the literature on ore deposits there is occasional mention that an oreshoot or district is on an anticline, but in most of the descriptions no weight or significance is attached to the relation, and usually the fact is concealed in a mass of structural detail. A few writers have stressed the relationship in a few districts or on a certain type of deposit. Church, Spurr, Butler, Stahl and Schuette have called attention to certain features, but the general extent of such a correlation has not been made known in any publication that the author has seen. A recent article1 on the localization of ore deposits, by well-known geologists, does not consider this common association. The author has seen in the field a number of the structural features described, and in addition has made a fairly complete review of the literature. This paper presents enough of the examples found to show the frequency of the relation to anticlines, and since only a few deposits on synclines are known, all of these of any importance of which the writer knows are mentioned. With certain qualifications which are discussed later, epigenetic ore deposits of replacement or vein type are mostly found where local upwarps of the earth's crust have taken place. Where formations antedating the ore deposits are present in the proper attitude to demonstrate vertical warping (i. e., more or less horizontal beds) the structural feature on which a mineral district, or mineralized area is located is almost always anticlinal, or domelike in nature. Some or even most of the ore deposits in a given district may be on the flanks of the upwarp, but few major districts are located definitely on downwarped areas. Synclinal basins within certain limits of size appear to be unfavorable to the type of fracturing that admits ore-bearing solutions. Replacement orebodies frequently are localized in small anticlines or domes, the size of the anticline or roll often being more or less commensurate with that of the enclosed oreshoot. This feature certainly ranks

Jan 1, 1931

By J. H. Nead

OBJECT THE experiments herein described were undertaken with a view to investigating thoroughly the influence of carbon on the tensile and impact physical properties of carbon steel. The original comprehensive plan included investigation of a series of steels with varying carbon contents over a wide range of heat treatments. These were to be studied as to their static tensile qualities, and also their resistance to shock as measured by the Charpy impact bending test. A thorough metallographic examination was likewise included in the schedule. The Charpy tests and the metallographic examination have not been completed to date, and are accordingly withheld for another report. All heat treatments, however, have been made, and the static tensile tests have been completed. A description of the procedure of the experiment and the results thus far obtained are therefore reported herein. CONCLUSIONS No attempt is made to draw general conclusions from these experiments, but the curves and the data are submitted as being of general importance and wide applicability.

Jan 12, 1915

By R. Neilson Clark

The discovery of a thin pay streak, yielding carbonates of copper; native silver, and perhaps chloride of silver, was made on the 9th of April, 1874, within the trachytic belt which forms part of the Sierra Mojada. The discoverer named it the Humboldt Mine. On the 2d of May, 1874, another discovery was made, in a northwest direction from the Humboldt, at about five hundred feet distant, this was named the Pocahontas Mine. After some exploration these two discoveries were proven to be on the same vein. To the southeast of the Humboldt a claim had already been taken up, called the Virginia; and to the northwest of the Pocahontas, one called the Southeast Leviathan. On these' last two this same vein has been found and worked. This paper will therefore treat of the Humboldt-Pocahontas vein, as worked on these four claims, to wit: beginning at the northwest, the Southeast Leviathan, the Pocahontas, the Humboldt, and the Virginia claims. Since the spring of 1874, there has been sunk on this vein a total of twenty-seven hundred and fourteen feet of

Jan 1, 1879

By R. Neilson Clark

THE discovery of a thin pay streak, yielding carbonates of copper, native silver, and perhaps chloride of silver, was made on the 9th of April, 1874, within the trachytic belt which forms part of the Sierra Mojada. The discoverer named it the Humboldt Mine. On the 2d of May, 1874, another discovery was made, in a northwest direction from the Humboldt, at about five hundred feet distant, this was named the Pocahontas Mine. After some exploration these two discoveries were proven to be on the same vein. To the southeast of the Humboldt a claim had already been taken up, called the Virginia; and to the northwest of the Pocahontas, one called the Southeast Leviathan. On these last two this same vein has been found and worked. This paper will therefore treat of the Humboldt-Pocahontas vein, as worked on these four claims, to wit: beginning at the northwest, the Southeast Leviathan, the Pocahontas, the Humboldt, and the Virginia claims. Since the spring of 1874, there has been sunk on this vein a total of twenty-seven hundred and fourteen feet of

Jan 1, 1879

By Robert R. Walden, LeMont West

K ENTUCKY'S first acid-grade fluorspar flotation Kmill, shown in Fig. 1, was placed in operation Aug. 1, 1952, by the Pennsylvania Salt Manufacturing Co. at Mexico, Ky. During 1951 a critical shortage of acid-grade fluorspar developed and it became necessary for the company to produce part of its fluorspar requirements. In 1951 the company purchased the Crider and Lennen metallurgical fluorspar mill and an adjacent stockpile of tailing at Mexico, Ky. The tailing, assaying about 26 pct calcium fluoride, originated from log washer and jig mill concentrators in the area. As the mill did not have a fluorspar dryer or convenient rail facilities, the company leased the Burleson concentrator at Marion, Ky., where these facilities were available. At Marion, Ky., on the Illinois Central Railroad, dry acid-grade fluorspar is transported direct to the company's Calvert City, Ky., hydrofluoric acid plant. The Mexico flotation plant was reconditioned and designed to produce acid-grade fluorspar from the jig tailing stockpile. The new plant flowsheet is shown in Fig. 2. The ore feed, old tailing, which contains 10 pct of waste rock and coarse gravel assaying approximately 8 pct CaF,, is bound together by sticky clay

Jan 1, 1955

IN the preceding chapter on thermochemistry and the reactions in and between metal and slag phases and in the following chapter on fuel combustion the main emphasis is placed on the equilibrium or "static" conditions. This equilibrium viewpoint is not concerned with the rate of change in the process or with the mechanisms or paths followed between initial and final states. The questions of just "how it works" and "how fast" belong to the kinetic aspect of any process; their answers are helpful in speeding up or slowing down and thus controlling its operation, and also in understanding its limitations. Any treatment of kinetic factors in the open hearth such as is attempted here and in Chapter 22 must at present be largely qualitative and incomplete. We are only beginning to get quantitative data on rates of reaction and diffusion at high temperatures, as indicated in Chapter 15. Empirical data in the literature on furnace operating rates do not help much to illuminate the details of gas-flow patterns and the complexities of heat flow in the many parts of the furnace system. This chapter is intended to give the reader an introduction to the problems of the flow of gases through the furnace system and the flow of heat in this system. An adequate discussion would require several times the space available here; it is possible here only to outline a few fundamentals and to indicate some of the conditions of heat and gas flow peculiar to the open hearth. Several good general treatments of these subjects may be found in the literature (see references at the end of the chapter). For the designer of open-hearth furnaces, the principles of gas flow are of paramount importance. They are also important to the operation of the process, at least to the extent of a general qualitative picture of the movement of gases in the system. MOTION OF GASES IN FURNACE DUCTS Fluid flow in general can vary between the extremes of laminar or streamline flow with a minimum energy loss, to irregular

Jan 1, 1951

By Mark C. Malamphy

The occurrence of outcrops of bituminous schists and sandstones impregnated with heavy asphaltie petroleum first directed attention to the São Pedro area as a possible source of commercial production of petroleum. Since 1920, more than 20 wells have been drilled in this area. The discovery of oil shows and small quantities of natural gas in some of the early wells led to the continuation of drilling in the hope that more important findings would result. During the early part of 1934, detailed magnetometer observations were made in this area, and a considerable number of torsion balance stations were occupied. The results of these geophysical observations help considerably to clarify the structure of the area and the very considerable amount of geologic information available makes possible a much more exact interpretation of geophysical anomalies. In presenting the results of these observations, and interpretation of the geophysical data, certain actual case problems are included; i.e., geophysical anomalies due to anomalous masses of which the forms and positions are more or less known. Although anomalies due to igneous intrusions are probably more important to geophysicists in Brazil than in other countries, these data have a certain interest for all geophysicists, particularly because they were obtained in the south magnetic hemisphere, where the lines of magnetic force are directed upward, and in a region of moderately low inclination. This is considered as a geological-geophysical problem, and only passing mention will be given to the petroleum possibilities of the area. General Geology The location and general geology of the São Pedro area are shown in the sketch map of Fig. 1, which is adapted from the geologic map of South Brazil compiled by Oppenheim1,†- who gives the geologic column of South Brazil (So Pedro and vicinity) as follows:

Jan 1, 1940

By Mark C. Malamphy

The occurrence of outcrops of bituminous schists and sandstones impregnated with heavy asphaltie petroleum first directed attention to the São Pedro area as a possible source of commercial production of petroleum. Since 1920, more than 20 wells have been drilled in this area. The discovery of oil shows and small quantities of natural gas in some of the early wells led to the continuation of drilling in the hope that more important findings would result. During the early part of 1934, detailed magnetometer observations were made in this area, and a considerable number of torsion balance stations were occupied. The results of these geophysical observations help considerably to clarify the structure of the area and the very considerable amount of geologic information available makes possible a much more exact interpretation of geophysical anomalies. In presenting the results of these observations, and interpretation of the geophysical data, certain actual case problems are included; i.e., geophysical anomalies due to anomalous masses of which the forms and positions are more or less known. Although anomalies due to igneous intrusions are probably more important to geophysicists in Brazil than in other countries, these data have a certain interest for all geophysicists, particularly because they were obtained in the south magnetic hemisphere, where the lines of magnetic force are directed upward, and in a region of moderately low inclination. This is considered as a geological-geophysical problem, and only passing mention will be given to the petroleum possibilities of the area. General Geology The location and general geology of the São Pedro area are shown in the sketch map of Fig. 1, which is adapted from the geologic map of South Brazil compiled by Oppenheim1,†- who gives the geologic column of South Brazil (So Pedro and vicinity) as follows:

Jan 1, 1940

By P. H. Dudley

THE piping and segregation of ingots of steel is a comprehensive subject, and must be studied in reference to the different grades of soft, medium, and hard steel, rather than to discuss it in a general manner, as though applicable to all grades. Rail steel, however, will receive the most consideration in this paper, for the wheel-loads of the motive pourer and rolling stock have doubled from 1890 to 1910. Steel rails and tires which were efficient under the light loads, became less serviceable under the double wheel-loads, quadrupled tonnage, and higher speeds. Bessemer Steel. Bessemer steel of froth 0.10 to 0.15 per cent. of carbon, for splice-bars, spikes, and tie-plates, rises in setting, and is cast in bottle-mouthed molds, which must be capped to prevent an over-flow from the top. This grade of steel rises in the molds and makes a longer ingot than the volume of molten steel when first teemed. The ingots which are allowed to cool and then cut open, show, particularly in the upper part, large occluded blow-holes, and when they are Dot oxidized or do not contain foreign matter, weld more or less completely when the steel is rolled or forged above 1,100° C., and it :is in this way that the blow-holes are closed it the low-carbon steels.

Jan 4, 1913

By Frank Speller

WE are here to honor again the memory of Henry Marion Howe, one of the foremost metallurgists of his time, and it is indeed a great privilege to be called upon by the Board of Directors of .this Institute to give the memorial address this year. Professor Howe started active investigation of corrosion of iron from a metallurgical standpoint in 1887, and made several important contribu-tions to the subject from 1895 to 1908.(1) ? The papers named in the bibliography are only a few of his valuable papers, but in all his works he sets a high standard of scientific accuracy, together with a clearness and power of expression rarely equaled in engineering literature. There-fore it seems appropriate on this occasion to review the work on corrosion of this distinguished gentleman and then endeavor to make a brief inventory of what has been accomplished since his time. Howe saw the beginning of the steel industry in America and before he died (May 14, 1922) witnessed it develop to a production of 45,000,000 tons per year. He was naturally very much interested in the infant industry and was quick to see the importance of the question of corrosion. It was my privilege to discuss the subject of corrosion frequently with Professor Howe at various times from 1905 to 1908; in this, as in other metallurgical problems, he sought the truth without bias and always insisted on proving an opinion or conclusion before accepting it. We should remember that when Howe started his investigation of corrosion, in 1887, steel was rapidly supplanting wrought iron. Certain papers in the early eighties (now forgotten) claiming much greater durability for wrought iron than for steel aroused Howe's interest. He could not reconcile the statement that steel was intrinsically and incurably less durable than wrought iron with the continued and widening use of steel,

Jan 1, 1934

By Dwight L. Baker, Alexander Knoll

The work herein reported shows that galena in certain organic solutions of fatty acids becomes coated with lead soaps, and that this coating is not only highly water-repellent but is also repellent to certain organic liquids, particularly those of high surface tension; i.e., nitrobenzene, diphenylmethane. Wetting Properties of Galena in Nonaqueous Fatty Acid Solutions When a "captive bubble"I is withdrawn from a polished, plane galena surface under a nitrobenzene solution of stearic acid, the air bubble shows a decided tendency to "cling" to the mineral surface. The contact angle, therefore, was greater than zero, although it was not large enough to be measured quantitatively by the captive-bubble method." When pure nitrobenzene was substituted for the nitrobenzene-stearic acid solution, no clinging of the bubble was observed; viz., contact angle = zero. Although the contact angle developed in air-galena-nitrobenzene-fatty acid solution was small, the organic solvent repellency of the galena surface was great enough to enable good recovery in a laboratory flotation cell2 In Table I are given the results of flotation experiments using several different fatty acids dissolved in nitrobenzene.

Jan 1, 1943

By Alexander Knoll, Dwight L. Baker

The work herein reported shows that galena in certain organic solutions of fatty acids becomes coated with lead soaps, and that this coating is not only highly water-repellent but is also repellent to certain organic liquids, particularly those of high surface tension; i.e., nitrobenzene, diphenylmethane. Wetting Properties of Galena in Nonaqueous Fatty Acid Solutions When a "captive bubble"I is withdrawn from a polished, plane galena surface under a nitrobenzene solution of stearic acid, the air bubble shows a decided tendency to "cling" to the mineral surface. The contact angle, therefore, was greater than zero, although it was not large enough to be measured quantitatively by the captive-bubble method." When pure nitrobenzene was substituted for the nitrobenzene-stearic acid solution, no clinging of the bubble was observed; viz., contact angle = zero. Although the contact angle developed in air-galena-nitrobenzene-fatty acid solution was small, the organic solvent repellency of the galena surface was great enough to enable good recovery in a laboratory flotation cell2 In Table I are given the results of flotation experiments using several different fatty acids dissolved in nitrobenzene.

Jan 1, 1943

By James Ferguson

THE fact that little if anything has appeared in the technical press or in the Transactions of the Institute on the subject of roll shells proper, used in various grinding appliances such as Cornish rolls or Chilean mills, may be taken as an incentive, if not an excuse, for the present article. No attempt is made to enter into a. discussion as to the theory or mathematics of crushing as performed by rolls, the subject being treated in a general way with respect to the manufacture of roll shells 'and some salient points touching on their adaptability and wear in service. While it stands to reason that skill coupled with judgment in the mechanical design of rolls, Chilean mills or other types of grinding machinery, with special reference to strength of parts, nicety of adjustment and other mechanical features, stand for efficiency in their operation .and satisfaction in service, the exceedingly important item. of roll shells or other wearing parts entering into their construction should not be lost sight of. In other words, a well-designed piece of grinding machinery is just as inefficient in service, when equipped with poor roll shells or shells made of the wrong or an inferior grade of metal, as good roll shells made according to the best practice the steel maker knows, working on an old or antiquated set of rolls. Unfortunately there is a tendency occasionally for the machinery builder to blame the steel maker or vice versa if roll shells do not wear well or evenly, or if they break before being worn down to their ultimate thin point. There is no occasion for this attitude, as the product, of each must stand on its own merits. But it is essential that the two work in harmony since the machinery builder usually does not furnish the shells for his rolls or grinding mills, but depends on the steel maker, who makes a specialty of this rolled product, to give the particular needed element of efficiency to his machine.

Jan 9, 1914

By Culver, Richard S.

In spite of the widespread interest in rock bolt research, relatively little is known about the critical region surrounding the bolt anchor. In analyzing the stress distribution around an opening resulting from rock bolt support, it is commonly assumed that the bolt is fixed at a point far enough from the surface so that the anchor does not influence the performance of the bolt. Furthermore, a bolt anchor is assumed to per- form satisfactorily if it will hold the design load with a minimum amount of load relaxation, commonly called bleedoff. From the standpoint of the design engineer both of these assumptions are reasonable, but they ignore the fact that the extremely high stresses in the region of the anchor are capable of generating fractures in the rock. Lang estimated the bearing stresses for a slot and wedge anchor on a one-inch-diameter bolt to be as high as 125,000 psi. This paper describes a more thorough analysis of the magnitude of the stresses around the anchor and the nature of the potential fractures that might result.

Jan 1, 1968

By George E. Thackray

In December, 1894, the Cambria Iron Company made a number of heats of Bessemer steel to be used in structures by one of its customers, subject to inspection and tests by a firm of consulting engineers, one of the requirements being that the material should riot exceed .08 per cent. of phosphorus. In other respects the requirements were such that they could only be met by material of good quality; but the general spe cification is not introduced here, as it is not the purpose of this paper to deal with anything except certain difficulties encoun tered in determining the phosphorus-content of the material in a manner satisfactory to both seller and buyer. Preliminary determinations of phosphorus were made in sample-ingots from each of the heats from which material was rolled for the order in question, and these preliminary chemical tests, made in the laboratory of the Cambria Iron Company, showed that, with very few exceptions, every heat was within the prescribed limit of phosphorus. After the material had been rolled, sample-drilling8 of finished material were taken from the various heats in the regular manner in use at the works, these samples being thoroughly mixed and divided into two parts, one of which was analyzed at the works' laboratory and the other sent to the inspecting engineer. Several hundred determinations were made from this mate rial without reaching an agreement between the work of the inspector's chemist and that of the works' chemist; but as it is not the object of this memorandum to treat of this part of the subject at length, it is considered sufficient to present herewith only a few of these first determinations. The analyses given in Table I. are those of the original series made on the heats which were afterwards resampled for final determination by an arbitrator; and they are selected for this reason, as the entire " comparison is thus rendered more complete.

Jan 1, 1896

By Robert E. Hoffman, John B. Hudson

The self-diffusion coefficient of pure lead has been measured at five pressures between atmospheric and 40 kb. over a temperature range of about 150°C near the melting point at each pressure. Measurements were made using a radiotracer technique, samples being sectioned electrochemically after the diffusion anneal to determine the diffusion penetration curve. Pressure was applied in a "belt" type pressure device similar to that used by Hall et al., in the diamond synthesis. The self-diffusion coefficient, D, can be represented by an equation of the form at constant pressure, and an equation of the format constant temperature. An apparent correlation between the effects of pressure on self-diffusion and on the melting point of the material observed by Nachtrieb et al., at pressures below 10 kb. was found to be only approximate as measurements are carried to higher pressures. OVER the course of the past 30 years a large number of studies1-' of the rate of atom movements in solid metals have been carried out. These studies have in general been aimed at increasing the understanding of the detailed atomic process by which atom movements in metals can take place. The largest portion of these studies consisted of measurements of the self-diffusion coefficient, D, as a function of temperature. From such studies con- siderable information regarding the energetics of the motive process has been deduced. Recently such measurements have been extended to the pressure dimension. However, the existing work in this area is scanty and has in the past been limited to the pressures attainable in oil or gas bombs—i.e., up to about 10 kilobars (kb). In the present work, the self-diffusion behavior of pure lead has been investigated using the "belt" type high-pressure apparatus designed by Hall7 over a pressure range from atmospheric to 40 kb at temperatures extending over about a 150°C range close to the melting point at each pressure.

Jan 1, 1962

By José G. Aguilera

With the imperfect knowledge that me have of the geology .of the country in general, and of the numerous mining districts in particular, it is impossible to present an accurate idea of the geographical and geological distribution of the mineral deposits of the Mexican Republic. But, notwithstanding this, it is elear that the deposits are concentrated in limited regions of the country, and that certain deposits are so closely associated as to indicate, beyond doubt, a genetic relationship. The mineral deposits are numerous, and the most of them are found in the western part of the country in a zone following a SE.-NW. direction from Oaxaca to Sonora. In the eastern

Jan 1, 1902

By Norman P. Goss

It is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.l-8 The broadening of the Ka lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the diffraction lines are broadened and the Ka doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolution of the doublet is lost when a metal is cold-worked and the Laue spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attributed the hardening to fragmentation of the grains into smaller units. Jeffries and Archer,ll after carefully considering the problem of work-hardening from many angles, came to the conclusion that cold-working mechanically refines the grains into smaller crystal fragments, some of which at least differ in orientation from the parent grain. The increase in

Jan 1, 1940

By Norman P. Goss

It is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.l-8 The broadening of the Ka lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the diffraction lines are broadened and the Ka doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolution of the doublet is lost when a metal is cold-worked and the Laue spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attributed the hardening to fragmentation of the grains into smaller units. Jeffries and Archer,ll after carefully considering the problem of work-hardening from many angles, came to the conclusion that cold-working mechanically refines the grains into smaller crystal fragments, some of which at least differ in orientation from the parent grain. The increase in

Jan 1, 1940

By W. A. Klikoff, I. Fatt

The concept of fractional wet wattability is examined. Fractional water wettability of a reservoir rock is defined as the fraction of the internal surface urea that is in contact with water. Capillary pressure and relalive permeability of unconsolidated sand are shown to be functions of fractional wettability. INTRODUCTION The petroleum industry has long recognized that wettability of reservoir rock has an important effect on multiphase flow of oil, water and gas through reservoirs. As early as 1928 the American Petroleum Institute sponsored a study of wettability as part of API Project 27 at the U. of Michigan.' Despite 30 years of research, there is still little exact knowledge of the wettability of reservoir rocks. There are two parts to the wettability problem. After agreeing to a uniform nomenclature in regard to wettability,' the first question to be answered is, "What is the in situ wettability of a given reservoir rock?" If this can he answered the next question is, "What part does wettability play in determining the characteristics of multiphase fluid flow through the rock?" This paper represents an oblique attack on the problem of wettability. No attempt is made here to answer the basic question of wettability in situ. instead the consequences of the concept of fractional wettability are examined. Multiphase flow in sandpacks is shown to he highly influenced by fractional wettability. Jennings' has given 3 definition of wettability and the other terms used in discussing wettability. These terms must be applied to the physical situation existing In reservoir rock. A survey of the pertinent literature from 1928 to 1956 indicates that the concept of a contact angle was applied to reservoir rock in the same way it would be applied to a flat, homogeneous surface. Attempts were made to state quantitatively the wettability of a reservoir rock in terms of a contact angle which was presumably constant at all points on the very rough and heterogeneous interior surface of a porous rock. Calhoun, et al,3-6 prepared synthetic consolidated and un-consolidated porous media in which they claimed there was a known uniform contact angle. They then showed the effects on the capillary pressure and relative permeability characteristics of varying this angle. The API Project 47 at the U. of Texas' and others' have made extensive studies of an indirect approach to the contact angle through the use of heat of wetting data. Even if successful. however, this approach also states the wettability of porous rock in terms of a contact angle which is uniform over the entirc surface. If the angle varies from one part to another on the internal surface, there is no way of determining from the measurements the area distribution of contact angles. In 1956 Brown and Fatt5 suggested that the concept of a contact angle, as applied to reservoir rock, be abandoned. This suggestion was made because it is known that the internal surface of most reservoir rocks is composed of many different minerals, cach with a different surface chemistry and a different capacity to adsorh surface active materials from reservoir fluids. Furthermore, the operation of a contact angle in determining the form of a fluid-fluid interface is difficult to picture in the very complex geometry of a pore. Brown and Fatt proposed that the wettability of reservoir rock be stated in terms of the fractional internal surface area that is in contact with water or oil. All surfaces on which there is water are called water-wet; surfaces on which there is oil are called oil-wet. The fractional water wettability is then stated as a number which represents the fraction of the internal surface that is in contact with water. A symmetrical statement can be made for the fractional oil wettability. The concept of a fractional wettability as previously stated has in its favor the recognition of the heterogeneous mineral composition of most reservoir rocks. Another point in its favor is that fractional wettability can be measured quantitatively with relative ease. Hol-brook and Bernard10 se a simple dye adsorption test to obtain fractional wettability of reservoir rocks. Amott11 uses a combination of imbibition and displacement to arrive at a wettability index of reservoir rocks which seems related to fractional wettability in the range 0.25 to 0.75 fractional water wettability. Jennings" has shown the changes in relative permeability that take place when a porous material is changed from unity to zero fractional water wettability. He also shows that reservoir rocks in their natural state, but at room temperature and atmospheric pressure, have relative permeability characteristics which would indi-