Search Documents

By Ralph Hayden

PAGE I. IntRoduction........239 II. Definition of Anaconda SLime....240 III. The Source of Slime......240 Remodeled Flow Sheet......240 Old Plow Sheet,.......242 IV. ConStitution of Slimes......243 Chemical........243 Physical.........243 V. The Slime Problem.......247 VI. THe Experimental Slime Plant....248 VII. Slime Thickeners. ETc .......249 Slime Ponds........249 Tanks.........249 Comparative Efficiency of Open and Baffle Tanks .260 Callow Tanks........252 Kuchs-Laist Centrifugal Separator....253 Garred Filter........256 Dorr Continuous Thickener.....256 VIII. Concentrators........257 Round Table........558 Peck Centrifugal Concentrator....259 Competitive Tests.......260 Twenty-Deck Round Table..... 260 Slime Feed Distributor......261 IX. ConcluSion.........262 I. Introduction. In the wet concentration of ores there is always a certain amount of very fine material with which to contend. and which invariably carries such quantities of value that the treatment of it is worth while. commercially. This fine material usually contains that portion of the ore which hinders the separation of the mineral values: namely. the colloidal material resulting from the decomposition of certain constituents of the ore. The object of this paper is to show what efforts have been made to solve the slime problem as it occurs in the concentrator of the Washoe

Jan 1, 1914

By J. E. Kirby, L. B. Schnitz, H. E. Stamm III

The production history of a gas-cap-drive reservoir was reproduced by calculations, and predictions were made for operations under primary depletion, pressure maintenance by gas injection, and pressure maintenance by water injection. Although the general equations used in this analysis have been available to the industry for a number of years, the procedure has not had extensive use because of the unusually large time requirements for developing numerical results. The use of digital computing equipment for processing the calculation work generally reduced the time usually required for an extensive analysis of this type. Calculation techniques were developed that were equally applicable for solving the gar-cap-drive problem, whether digital computing equipment or desk calculators are used. These techniques are outlined and the procedures are illustrated by the field problem. INTRODUCTION The analysis of a gas-cap-drive res-ervoir requires the simultaneous solution of the volumetric balance1 and displacement2 equations. Equations for the analysis of combination drive reservoirs were presented by Wooddy and Moscrip in a previous paper." These equations permit the evaluation of possible operating processes in order that the optimum method of pro- ducing the reservoir may be determined. Although these equations represent the basic technique known for the detailed analysis of gas-capdrive reservoirs, the calculation processes are quite complex and time consuming; hence, the procedure has not had extensive use. Recently, these equations were satisfactorily applied with the aid of a digital computer to investigate the completion history of a gas-cap-drive reservoir under the following operating methods: primary depletion, depletion under full pressure maintenance by gas injection, and depletion under full pressure maintenance by water injection. The use of digital computing equipment substantially reduced the time necessary for making the computations and permitted a more concise investigation of the reservoir's depletion history than was possible when the desk calculator was used. This more rigorous investigation also permitted a detailed analysis of the calculation procedures necessary in the solution of the gas-cap-drive problem. This paper outlines the procedure of analyzing a gas-cap-drive reservoir and illustrates the process with an actual field problem. CHARACTERISTICS OF THE RESERVOIR ANALYZED Production in the field under consideration is obtained from a Frio formation of Oligocene age at a depth of approximately 5,740 ft sub-sea. The accumulation, which is bounded on the flanks by strand lines, is semirectangular in shape with gentle narrowing toward the base of the structure as shown by the sand limits and completion map in Fig. 1. The reservoir development indicates an oil column of 319 ft that is defined by gas-oil and oil-water contacts. Basic data relative to the characteristics of the formation and the formation fluids are shown in Table 1. The formation exhibits considerable shaliaess and thinning near the oil-water contact indicating that little or no benefit will be received from natural water influx. This is substantiated by the fact that wells completed near the original oil-water contact have not produced water. A sizeable gas cap is present; however, considerable faulting is in evidence, and it is believed that only a limited portion of the gas cap will aid in oil displacement and pressure maintenance. Although the reservoir was in an initial stage of depletion, it was believed that as soon as the equilibrium gas saturation in the oil zone was exceeded and a number of upstructure wells were invaded by the expanding gas cap, the resulting high gas-oil ratio production would rapidly dissipate the natural drive and lead to limited oil recoveries and inefficient reservoir operation. This analysis evaluated the effectiveness of the primary displacement mechanism and

Jan 1, 1958

D. F. HEWETT, Washington, D. C. (communication to the Secretary*).-I am not prepared to discuss the metallurgical use of manganese in the form of alloys. In connection with other work for the U. S. Geological Survey, however, I have been investigating incidentally, for about 5 years, the American as well as other sources of manganese. There are some conclusions that come out of this investigation that may interest those whose greatest interest lies in the use of the alloys. From a geological point of view, most manganese ore deposits may be regarded as concentrated masses of manganese oxides, as there are few masses of the other manganese minerals that are rich enough in manganese and low enough in silica to warrant smelting. The deposits of the Huelva district, in Spain, which are largely manganese carbonate and silicate, are exceptions to this statement. Some deposits of manganese oxides, such as those of Russia and Cuba, are bedded with ancient sediments, and although they are clearly concentrated under unique conditions, the source of the manganese cannot be determined. Probably 60 per cent. of the world's production of manganese ore, or 95 per cent., if that of Russia be excluded, is derived from the superficial parts of deposits that have undergone weathering and enrichment near the surface. In other words, the situation with the manganese ore supply is such as it would be with regard to copper, if instead of being derived largely from deep zones of deposits of deep-seated origin, such as veins, it were derived solely from the zone of secondary enrichment. Manganese oxide occurs in all rocks but is most abundant in igneous rocks, of which, according to Clarke, it forms an average of 0.10 per cent. It also forms 0.05 per cent, of the average limestone, but only traces are present in shales and sandstones. It is interesting that although many commercially important manganese deposits occur in rocks that are but slightly richer in manganese than the average, the most important deposits occur in rocks of unusual character that are much richer in manganese than the average. Thus, the most important deposits of India and Brazil overlie or occur near masses of rocks that contain excessive amounts of manganese garnet and pyroxene.

Jan 5, 1917

By Noel H. Stearn

When the Age of Machinery was suddenly thrust upon civilization about the beginning of the 19th century, an unprecedented demand for mineral resources sprang up. This demand brought about the rapid development of the known ore deposits and the discovery of such other deposits as could be encountered by energetic and canny prospectors. Thus in the countries now reasonably accessible nearly all orebodies have been located except those which are totally concealed even from the eyes and "senses " of experienced and expert prospectors. The high rate of exhaustion of known ore deposits and the necessity of looking farther and farther ahead for raw materials as a matter of insurance on the stupendous capital outlays involved in mining, development, and conversion operations, have resulted in exceptional activity in three different fields of effort. The first is purely geographic. Prospectors are now penetrating the few hitherto inaccessible regions in the hope of stumbling upon exposed ore deposits or locating visible indications of their presence. The second is chemical. Industrial chemists and metallurgists are seeking to facilitate the exploitation of lower grade ores or to find methods of recovering valuable metals from common substances. In the third field of effort lie the activities of the economic geologist and the mining engineer, who endeavor to locate concealed ore deposits which would remain hidden from the prospector no matter how expert or conscientious he might be. Obviously the task which such a man must face is both exacting and indefinite, and the tools which he has heretofore been permitted to bring to it are, for the most part, abstract—a knowledge of certain fundamental principles and processes involved in the origin, occurrence, structure, and distribution of deposits of natural resources and of the rocks which form the environments of those deposits; and a process of reasoning by analogy supplemented by the use of the diamond drill, or such artificial exposure as the test pit, trench, shaft, or tunnel.

Jan 1, 1929

By R. S. Christie

Reservoir pressure is the pressure at which a fluid is held in a state of equilibrium in a porous stratum. This pressure may be a result of the genesis of oil or gas and its subsequent migration into and through an adjacent porous stratum, or of hydraulic head. Reservoir pressure is an indication of the potential energy contained in the reservoir, and when it is known the engineer is in a position to use it to advantage in recovering and lifting the oil. It is important to know the pressures in any type of reservoir, but this knowledge is probably of greater value in a limestone reservoir, as at Hobbs, where producing rates or conditions may be more sensitive to changes in pressures. The Hobbs field is in east central Lea County, New Mexico. The discovery well was completed by the Midwest Refining C I. in 1928, but intensive development did not begin until after the completion by the Humble Oil and Refining Co. of No. 1-A Bowers in February, 1930. There are 143 producing wells on approximately 5500 acres. The field has not been defined to the northwest, but a projection of structural contours indicates that the productive area ultimately may cover 7500 acres. The producing horizon is the White or Crystalline lime of Permian age. The top of the lime is found at an average depth of 4000 ft. and the wells penetrate it an average distance of 200 ft. The main pay zone is an oolitic stratum about 25 ft. below the top, and varies from 2 to 15 ft. in thickness. Other porous or cavernous strata are found lower in the lime but have little saturation. The initial production varied from 100 to 25,000 bbl. per day, depending perhaps to some extent on the structural location but chiefly on the porosity of the pay. The initial gas-oil ratio varied from 325 to 16,000 cu. ft. per barrel. In wells where the top of the White lime was found below 350 ft. below sea level (Fig. 1)) the gas-oil ratio was usually less than 1500 cu. ft. per barrel, while in wells higher than 350 ft. below sea level, the ratio was usually above 2000 cu. ft. per barrel. The water table has been determined at about 620 ft. below sea level, by three wells on the west side of the field. With few exceptions, the wells have been completed with 7-in. casing cemented

Jan 1, 1932

By R. W. H. Acherson

Blast-furnace flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers and more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of Rue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained arc. shown in Table 1.

Jan 1, 1922

By R. W. H. Acherson

Blast-furnace flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers and more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of Rue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained arc. shown in Table 1.

Jan 1, 1922

By W. H. Kantner

In this paper, no attempt will be made to theorize on subsidence. Only known data and actual facts will be given, with a few exceptions noted where other factors and outside influences tend to change subsidence directly resulting from porphyry caving. The area under observation is known as the Southeast Extension of the East orebody. The orebody is irregular in outline and dips to the south and the east, extending in depth from about 425 ft. below the surface to 1050 ft. below the surface. In the upper horizon, the orebody is about 400 ft. long and 150 ft. wide. At 720 ft. below the surface, the ore outline is approximately 450 by 170 ft.; 70 ft. below this, it is 500 by 110 ft., with an extension at the north end to the east 270 by 120 ft. From this elevation to about 900 ft. below the surface, the ore spreads out to the cast and south, being about 700 by 500 ft. between these vertical limits. Below this it pinches out and at 1060 ft. below the surface is only 100 by 100 ft. The nearest point of the orebody—which is on the northwest side—is 600 ft. 'southeast of the Sacramento shaft. The country rock is all porphyry. Fig. 1 is a vertical east-west section showing orebody and original surface. The surface over the orebody was fairly regular and in this area and adjacent to it were portions of the surface plant, roads, and the main plant railroad to the concentrator. Fig. 2 is a map of the surface over the porphyry area. Caving operations started in April, 1925, at the approximate top of the orebody. The first lift was on the 600-ft. level; the ore was extracted by means of the Morenci timbered slide method and was from 425 to 455 ft. below the surface over an area of about 22,000 sq. ft. This lift was finished in May, 1926. The second lift, on the 650-ft. level, was already in production by May, 1926, so extraction of ore was continuous. This lift was 48 ft. high and covered an area of about 30,000 sq. ft. The ore from this lift was extracted by means of a modified Morenci timbered slide method. This lift was finished in March, 1927. The direction

Jan 1, 1934

By Walter Crafts, W. D. Forging, John J. Egan

Although many elements reduce the tendency to porosity in steel castings, manganese, silicon, aluminum, calcium, titanium and zirconium appear to be most generally suitable for the purpose. The manganese and silicon contents are usually maintained in a fairly constant range. Silicon-killed castings often are made to be sound with little or no addition of the stronger degasifiers. In many cases, however, it is more practical to utilize the stronger degasifying elements, aluminum, calcium, titanium and zirconium. Since they greatly modify the composition, shape, and distribution of the nonmetallic inclusions, and thereby the ductility, the strong deoxidizers must be used in such a way as to form the least harmful types of inclusions. As the reasons for failure always to obtain good results have not been obvious, an effort has been made to determine the mechanism of solidification of steels deoxidized to produce certain types of inclusions. Diagrams representsing the mechanism of their formation have been constructed from the appearance of the nonmetallic constituents and have not only illustrated the limiting features of specific deoxidizing treatments with respect to inclusion formation and ductility, but have also indicated a relation between inclusions and resistance to hot tearing. Three different types of deoxidation treatment have been used for obtaining sound castings with relatively high ductility. The first method is to make and cast the steel under such conditions that deoxidation with silicon and a small addition of a strong deoxidizer assures soundness. The effective addition that will promote soundness without causing the formation of intergranular inclusions varies with the furnace practice and composition, but may be limitled to about 0.025 per cent Al, Zr or Ti. Up to 8.10 per cent Ca and 0.15 per cent V are also used for this purpose. The inclusions in these steels are characteristically glassy silicates and round or irregular sulphides. As pointed out by Sims and Lillieqvist,1 the formation of fine intergranular inclusions, which are detrimental to ductility, limits the amount of strong deoxidizers that may be added.

Jan 1, 1940

By John J. Egan, W. D. Forging, Walter Crafts

Although many elements reduce the tendency to porosity in steel castings, manganese, silicon, aluminum, calcium, titanium and zirconium appear to be most generally suitable for the purpose. The manganese and silicon contents are usually maintained in a fairly constant range. Silicon-killed castings often are made to be sound with little or no addition of the stronger degasifiers. In many cases, however, it is more practical to utilize the stronger degasifying elements, aluminum, calcium, titanium and zirconium. Since they greatly modify the composition, shape, and distribution of the nonmetallic inclusions, and thereby the ductility, the strong deoxidizers must be used in such a way as to form the least harmful types of inclusions. As the reasons for failure always to obtain good results have not been obvious, an effort has been made to determine the mechanism of solidification of steels deoxidized to produce certain types of inclusions. Diagrams representsing the mechanism of their formation have been constructed from the appearance of the nonmetallic constituents and have not only illustrated the limiting features of specific deoxidizing treatments with respect to inclusion formation and ductility, but have also indicated a relation between inclusions and resistance to hot tearing. Three different types of deoxidation treatment have been used for obtaining sound castings with relatively high ductility. The first method is to make and cast the steel under such conditions that deoxidation with silicon and a small addition of a strong deoxidizer assures soundness. The effective addition that will promote soundness without causing the formation of intergranular inclusions varies with the furnace practice and composition, but may be limitled to about 0.025 per cent Al, Zr or Ti. Up to 8.10 per cent Ca and 0.15 per cent V are also used for this purpose. The inclusions in these steels are characteristically glassy silicates and round or irregular sulphides. As pointed out by Sims and Lillieqvist,1 the formation of fine intergranular inclusions, which are detrimental to ductility, limits the amount of strong deoxidizers that may be added.

Jan 1, 1940

This paper "On Coal" was published in three issues of The Western Gleaner in 1814. Name of author is not given. This magazine was started by Cramer, Spear & Eichbaum, in Pittsburgh, Pa., in December 1813, and ran for about two years. Copies are very rare, and this one is made from an original in the Darlington Library, University of Pittsburgh. This is almost certainly the first general article on coal published west of the Allegheny Mountains, and one of the earliest in this country. ON COAL Its Natural History-Mining of Coal-Phenomena occasioned by Fire-damp-Method of Coking-Distillation of Tar from Pit-coal-Gas-light-Coal, a Manure I. NATURAL HISTORY OF COAL There are few productions of nature which present to the philosopher a wider field of investigation than pit-coal. A substance highly inflammable is found in the deep recesses of the earth, sometimes loaded with numerous superincumbent strata of hard rock, and extending frequently along with these strata through a vast expanse of territory. Though metals may be said to be inflammable substances, as they combine more or less rapidly with oxygen when placed under particular circumstances, yet the character of rapid combustion with disengagement of light and heat, seems to belong. principally to such substances as are derived either from the animal or vegetable kingdom. That this is probably the case with regard to coal we are further induced to believe, by the remarkable circumstance, that the chemical analysis of this natural production yields especially, though in various proportions, those materials which constitute essentially the vegetable. And if any thing was wanting to confirm, us in that opinion we might trace in a number of fossile substances the gradual transition of the vegetable into the state of mineral coal. This fact is so intimately connected with the natural history of coal, that we cannot think it superfluous to give it some farther development. Among the great number of principles which the chemist is capable of tracing in the vegetable kingdom, the presence of extract, resin and fibre seem to form the characteristical marks of plants.-If vegetable matter be boiled in water, and the water, after having been strained and filtered, be exposed for some time to the open air, a flocculent precipitate takes `place from every part of the liquor; which soon subsides to the bottom of the vessel containing it. This is the extract; altered, indeed, by exposure, and now no longer soluble in water, a change which is supposed to depend on the absorption of oxygen; and if, by any means the proportion of oxygen be increased, the extract gradually becomes of a darker color, blackens, and approaches to the state of charred wood.

Jan 1, 1942

By Ligon Johnson

ONLY the acute phase of the smelter fume problem is new. The problem itself is older than the Christian era. While both lead and copper were mined and crudely smelted ; on: 3,000 years ago, it was not until the Roman occupation of the Iberian Peninsula and the British Isles, which occurred but shortly before the beginning of the Christian era, that there was any evidence of smelting operations on a scale sufficiently large to permit a fume problem. Around Huelva, Spain, are found more than 30 million tons of slag from lead smelting conducted there by the Romans. Pliny tells us that more than 20,000 slaves were employed in the Iberian mines. Extensive mining and smelting by the Romans in England and Wales were coincident with the Iberian proceedings. These metallurgical operations were upon a sufficiently large scale to produce marked results both upon the surrounding country and the smelter workers, but, as they were those of a conqueror upon conquered soil, conducted by slaves, imperial Rome failed to recognize that such a thing as a smoke problem did or could arise, and whatever fume question there may have been at that .time remained a question only to those who had no chance to answer any phase of it. The smelting operations of the Romans extended over about 400 years, and little is "recorded of lead and copper smelting from that time until the 16th century. From the revival beginning at this period up to the present century, the growth of smelting has been comparatively gradual. In Great Britain, smelting was conducted almost wholly in localities where metallurgical operations were of paramount importance, and the communities that grew up in smelter localities were due to and dependent upon the mines and smelters. This fact had much to do with the comparative freedom of British smelting from burdensome fume litigation and legislation. To a lesser degree these conditions applied to the German operations which, when coupled with the further fact that most of the early German operations were to a greater or less degree fiscal workings of Prussia, Saxony and Brunswick-Hanover; accounts for

Jan 5, 1917

By Stirling Huntley, L. G. Huntley

THE controversy regarding the ,'probable future of the Mexican oil fields, and its relation to the oil industry of the United States, has led to the preparation of this paper. As has been predicted by several writers in recent papers, certain of the producing areas in the so-called "southern fields" in the Tampico Embayment have only a limited oil reserve. These areas are being pulled on by every pipe line in that region, and the length of time that they will continue to produce is a direct factor of the daily oil shipments of these companies. However, this is not the whole story, and in the following paragraphs an attempt will be made to show that the life of Mexican oil production will be a long one, and Mexican oil will continue to be a large factor n the market for an indefinite time after the areas mentioned above have been drained. The past and present producing fields will be discussed separately, in order-to establish a basis for comparison, the ,only method by which underground reserves 'can be estimated in these fields.

Jan 1, 1921

By Hadyn W. J. Wren

The practical experience obtained from designing and commissioning of fully controlled coal preparation plants, using centralised mini computers is discussed. The importance of defining a workable operating philosophy is highlighted with particular reference to the problems associated with trying to achieve a total 'hands off' concept. These experiences with a centralised computer controlled system have led to a deeper understanding of the interaction between the operation and the control system and the role of local control and management information within the overall control philosophy of a highly automated process plant. The utilisation of an extensive fully distributed microprocessor control system with over 6500 digital and analogue signals split into six autonomous areas with a supervisory system to provide operator interface is described. The important aspects of project definition and design needs are outlined with particular regard for achieving maximum efficiency with minimum complexity. Views of future trends are offered, based on the experience of both centralised computer and distributed processor systems.

Jan 1, 1984

By William G. Pariseau

There are important phenomena in rock and soil mechanics that cannot be explained in terms of theories of homogeneous, isotropic materials. Subsidence of strata about mine openings is an example. In-situ stress measurements in nonisotropic sedimentary and metamorphic rocks is another. Patterns of joints, faults, fractures, and similar geologic features impart directional mechanical properties to rock masses that are locally isotropic or anisotropic. On the geologic scale, the nonhomogeneity of composite rock masses may, in certain instances, be dealt with as homogeneous anisotropy. The mechanics of large rock masses can, therefore, be expected to involve considerations of anisotropy. The source of the anisotropy is not relevant. Once the scale of observation is selected and the material is defined accordingly, the analysis of stress and deformation proceeds without regard to the numerical values of the material constants. There are also important phenomena in rock and soil mechanics that cannot be explained in terms of linear elasticity, theory. For the mechanical description of anisotropic geologic materials capable of deforming beyond the limit of purely elastic strains, a plasticity theory is required. The purpose of this chapter is to present a plasticity theory for anisotropic rocks and soils. The proposed theory is based on the work of Hill in anisotropic metal plasticity and represents an extension of his work so as to include anisotropic geologic materials. The point of departure from metal plasticity theory begins with the inclusion of the normal stresses as linear terms in the yield condition, which plays a central role in plasticity. Once the yield condition is established, the plastic strain increments are obtained immediately through the principle of normality. For practical applications, some simplification of the three-dimensional theory is re-

Jan 1, 1972

By J. H. Fletcher

ALTHOUGH some mines have been completely mechanized, on the whole mechanical equipment has made slow progress in the coal fields. Coal mining is particularly well adapted to hand labor. The skillful hand miner can keep his working place safe under difficult roof conditions, remove impurities from the coal at the point of origin, and produce a maximum percentage of large-size coal, so as to command the highest price on the market. Hand mining has also the advantage of low capital investment per ton of production and moderate carrying charge when the mine is idle. Though animal haulage gave way to electric locomo-tives and hand cutting to mining machines, beyond these concessions most of the tonnage is still produced by manual labor. But factors over which producers have no control are speeding the change to mechanical mining. The additional investment in underground equipment and surface preparation plant must be offset by a great increase in tons per man-day, and to do this the employees should be able to utilize as much of their time as possible on production. In the installation of mechanical mining, the only change in method usually has been to add loading machines to a mine already developed for hand loading. Because of a lack of suitable equipment, few mobile loading machines have been installed in seams of coal less than 4 ft. thick; the mechanization in the thinner seams has been confined largely to shaking conveyors and hand loading onto chain conveyors. Mechanical mining requires an organization that is prepared to study its particular problem from production territory to market in recognition of the changed factors arising from the use of loading machines at the working face, and other causes, such as safety of men and property; high wage scale on hourly basis; concentrated working territory and rapid extraction from a given area; change in the percentage of sizes of coal produced and effect of this on average realization. There are also the coal-cleaning problem; increased capital investment, maintenance, obsolescence, and the relation of all these to the spread between realiza-tion and production cost. If coal seams were uniform, the answer would

Jan 1, 1939

By G. Van Esbroeck

THE copper mines of the Katanga region in the Belgian Congo lie along the same mineralized belt as those of Northern Rhodesia. There are two distinct types of deposits in that belt, the dolomitic and the quartzitic. In the dolomitic type the metallic minerals are found in a dolomitic limestone country rock. Through oxidation and enrichment, large deposits of high-grade oxidized copper ores were formed, some of which are being worked by the Union Miniere du Haut Katanga. Such deposits are all in Katanga. The quartzitic deposits are found in Katanga and Northern Rhodesia. Here the primary mineralization occurred in sandstones and quartzites, in horizons stratigraphically lower than the dolomites. These rocks are not favorable to secondary enrichment and the oxidized zone is poorer than the sulphide zone, which alone contains the ore. There are also in Katanga a few ore-bearing veins. One of them is being worked in the Prince Leopold mine at Kipushi.

Jan 1, 1939

By Donald R. Reichmuth

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks."1 There are now three distinct approaches being used to determine the tensile strength of brittle materials. These are shown schematically in Fig. 1. The first method consists of simply pulling the specimen apart by applying an axial load. Although this procedure is the easiest to understand, the technical problems encountered during testing are numerous. Specimens cannot be readily fabricated into dumbbell-shaped specimen* like those customarily used for testing inetals. Cylindrical specimens cannot be loaded in jaw-clamps because adverse stress conditions arise at the clamping points, which causes unreliable results. An innovation developed by Niles Grosvenor at the Colorado School of Mines, in which the load is applied through steel-end caps glued to the ends of the specimens, has considerable merit, hut the samples are costly to prepare.2 All tests using a direct pull are further handicapped by the possibility of small amounts of bending being present, the specimen's surface condition, and

Jan 1, 1968

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By Francis S. Peabody

This paper will not be a technical paper, because, although I have been in the business of mining and selling coal for 30 odd years, I am neither a mining engineer nor a practical miner. If I digress from time to time from my thesis, I must be forgiven by the expert engineers and highly technical gentlemen for whose proceedings this article is written. Waste of the wonderful store of power that the Creator placed at our disposal appears to have been the theory and the basis of our methods of extracting this power—waste from the time the coal is mined to the time it is consumed. Let us consider the prime causes of this wastage which has been the heritage of the coal mining industry. In the early days—about 150 years after " Stone Cole" was discovered in Illinois by Joliet and Marquette, and Father Hennepin noted a "cole" mine on his map—the mode of mining prevalent among farmer landowners, on whose property coal was discovered near the surface or outcropping on the hillsides, was to enter the seam by a shallow shaft or drift into the hillside and remove the coal by wedging it down until a large room was left. The roof without support would fall and our primitive coal operator would then sink another shaft or drive another drift. In these early operations only the large lumps were taken and all small pieces and screenings were left to be covered by the fall of the roof—in fact this condition prevailed in Illinois up to about 1885. Gradually the method of mining changed from the open chamber, to a single entry with rooms turned to the right and left. Later, as the demand for coal increased and the necessity for larger mines became evident, the "room and pillar" system grew to be regular practice. The room and pillar system of mining consisted of starting away from the shaft bottom or drift mouth, with a pair of entries usually 12 to 15 ft. wide and about 30 ft. center to center, one entry being used for the air intake and the other for the return air and haulage; from each entry rooms or chambers were turned, narrow at the mouth and widening

Jan 1, 1918