Search Documents

By H. J. Polta, R. W. Michelson

Discounted cash flow analysis is commonly used to evaluate the profit making potential of a business venture. The same method can be used to analyze the effects of varying physical and economic conditions upon the real cost of supplying a mineral commodity. If a fixed rate of return on a capital investment is specified, and the flow of cash, discounted at that rate, is just adequate to repay the investment over the life of the venture, the net present value of the venture is zero. At this condition it is possible to evaluate the unit cost of producing the mineral. It will be exactly equal to the selling price required to calculate a zero present value. Increasing a particular cost factor will not always increase the cost of supply by the same amount. For example, in iron production from magnetic taconite, an increased cost per ton associated with beneficiation would be integrated into the discounted cash flow model along with local, State, and Federal taxes, depletion and depreciation allowances, resultant increased unit recoveries, and all of the other related component cost factors. Rather than adding to the cost, the factor may have a positive, instead of a negative, effect on the discounted cash flow and cause a decreased cost of supply. This value can be determined by a computer model which iterates the necessary selling price until the net present value is essentially zero. The discounted cash flow evaluation model lends itself particularly well to an application of the Monte Carlo simulation method for calculating a probability distribution of iron unit cost resulting from the probability distributions of the component cost factors.

Jan 1, 1969

By Raphael Titi-Manyaka, I. Iwasaki

Chlorination and chloridization behaviors of pyrite, pyrrhotite, chalcocite, covellite, chalcopyrite, bornite, heazlewoodite, millerite, and pentlandite in chlorine, gaseous ferric and sulfur chlorides were investigated by thermogravimetric analysis. The reaction mechanisms are discussed in terms of theoretical weight changes, thermodynamic calculations, and X-ray analyses of reaction products. The experimental findings are in direct application to the development of a scheme for producing nonferrous metal chlorides, elemental sulfur, and ferric oxide from complex sulfide flotation concentrates.

Jan 1, 1977

By G. D. Van Ardsdale, A. W. Hudson

Heap leaching, as practiced at Rio Tinto, Spain, while one of the oldest, and probably one of the cheapest, methods of extracting copper from its ores, has not had, until recently, other than experimental application in this country. This has been due partly to a mistaken idea that the Rio Tinto ores possess some obscure and mysterious quality that renders them alone suitable to the process, partly to the fact that tests properly made meant the expenditure of large sums of money and several years time, and partly to the fact that favorable commercial and other conditions are not often found. This paper gives some views on the chemistry and mechanism of the method, an account of the preliminary experiments, and the final plans adopted for a large-scale installation of the method by the Phelps Dodge Corpn. for treating low-grade ore from Sacramento Hill, Bisbee. If results comparable with those obtained from the test heap are to be had from the large plant, this plant will operate on the lowest-grade sulfide ore now being treated commercially in the country. The method has several advantages: The installation cost is low. Interest charges must, of course, be made both on the cost of the ore delivered to the plant and for the plant itself, but as these are low, there is considerable advantage in the ability to regulate output by more or less complete shutdowns in accordance with market and other conditions. The amount of labor needed is small, and the cement copper produced may be considered nearer a finished product than the sulfide concentrates from a mill, and certainly means less installation cost per ton to put into final form by present methods. At Bisbee, conditions were favorable for a trial of the method for, in the preparation of the Sacramento Hill orebody for steam shoveling,' a large amount of material below concentrating grade had to be moved to

Jan 1, 1923

By A. W. Hudson, G. D. Van Ardsdale

Heap leaching, as practiced at Rio Tinto, Spain, while one of the oldest, and probably one of the cheapest, methods of extracting copper from its ores, has not had, until recently, other than experimental application in this country. This has been due partly to a mistaken idea that the Rio Tinto ores possess some obscure and mysterious quality that renders them alone suitable to the process, partly to the fact that tests properly made meant the expenditure of large sums of money and several years time, and partly to the fact that favorable commercial and other conditions are not often found. This paper gives some views on the chemistry and mechanism of the method, an account of the preliminary experiments, and the final plans adopted for a large-scale installation of the method by the Phelps Dodge Corpn. for treating low-grade ore from Sacramento Hill, Bisbee. If results comparable with those obtained from the test heap are to be had from the large plant, this plant will operate on the lowest-grade sulfide ore now being treated commercially in the country. The method has several advantages: The installation cost is low. Interest charges must, of course, be made both on the cost of the ore delivered to the plant and for the plant itself, but as these are low, there is considerable advantage in the ability to regulate output by more or less complete shutdowns in accordance with market and other conditions. The amount of labor needed is small, and the cement copper produced may be considered nearer a finished product than the sulfide concentrates from a mill, and certainly means less installation cost per ton to put into final form by present methods. At Bisbee, conditions were favorable for a trial of the method for, in the preparation of the Sacramento Hill orebody for steam shoveling,' a large amount of material below concentrating grade had to be moved to

Jan 1, 1923

By Granville S. Borden

This brief is a reconnaissance report on some prospects in the field of taxation which can safeguard our Mineral Resources. The brief is a prospectus soliciting help and enthusiastic cooperation in the common task of developing these prospects in a manner which will be most beneficial to all parties-the owners, operators, employees, tradesmen, the federal and state governments, and the people of this nation.

Jan 4, 1950

Earth Sciences: The standard of living of the world's people depends upon human initiative, investigation, and know-how in exploiting the earth's resources. The Earth Sciences-geology, mineralogy, geophysics and geochemistry, meteorology, geography-are basic sciences dealing with those problems concerning the origin, constitution, and utilization of the earth's materials. The development of these fields in one department provides the greatest opportunity for direct contact and stimulus for scientists and teachers working in related fields. In the Earth Sciences, geology and mineralogy are obviously closely related. As rocks are the materials of which the earth is made, so in turn minerals are the constituents of the rocks. Conversely, a study of earth structures and the interplay of physical and chemical forces in the earth is necessary in order to understand the origin and source of minerals. Building on the basic core of knowledge of earth processes, earth structures, and earth history, the geologist will continue to push out the frontiers of stratigraphy, structural geology, pale-biology and petrology with growing insight into principles that control surface and subsurface rock conditions. As the field of geology has advanced, several lines of specialization have developed. The economic geologist

Jan 1, 1950

By Albert Roberts

Summary In response to a growing intolerance towards ground vibrations and noise as environmental pollutants the engineer must consider the effects of his operations as they are likely to be judged subjectively by the public at large. Much work has been done on the study of vibration damage to structures, but the damage criteria normally applied do not take into account any resonance effects, nor do they embody any subjective criterion. Mu1tiple criterion techniques of subjective appraisal have proven to be of value .in the assessment of environmental comfort in relation to ventilation, air conditioning, and lighting. One such scale, the Reiher-Meister Scale, has also been applied to ground vibrations and noise, and an attempt has been made to correlate this scale with objective criteria, using the parameters of frequency and displacement. This paper quotes examples and compares ground vibrations resulting from blasting, the operation of, vibrating and impact-hamner pi1e drivers, forge hammers, and railway and road traffic. The Reiher- Meister Scale was applied to a subjective-objective correlation in relation to vibrations from railway traffic and gave results which did not conflict with experience.

Jan 1, 1971

Map

Jan 1, 1938

By G. K. Burgess

G. K. BURGESS* and R. W. WOODWARD,? Washington, D. C.-From a metallurgical standpoint, there are several ways in which a reduction of the tin consumed in commercial non-ferrous and white-metal alloys can be effected. First, a reduction of the tin, content of the alloy; second, substitution of part or all of the tin content by some other metal; third, a substitution of a different type of alloy, which in some cases also involves a change in mechanical design. The Bureau of Standards has been studying these methods of conservation for tin alloys, particularly in regard to babbitts and bearing metals, bronzes, and solders. Much of the information secured by the Bureau was obtained from answers to questionnaires sent to manufacturers and users of these materials, so that, in general, any of the following suggestions or recommendations can be considered as being practical and as having already been thoroughly tried. Bearing Metals There is no question that the tin content of nearly all bearing metals can be reduced to some extent, and in some cases actually eliminated

Jan 12, 1918

By Wilber Stout

In Ohio, the annual output of coke made from native coals has averaged not more than 70,000 tons, or about enough to run a 200-ton blast furnace. Raw coal locally mined from the Sharon, or No. 1, bed was used for iron smelting in Mahoning furnace at Lowellville, Mahoning Co., as early as 1846. This practice was continued in the Youngstown district until the coal became scarce and the Connellsville coke more popular. At present, the Sharon bed contributes a part of the fuel for the production of ferrosilicon iron at Jackson, Jackson CO. About one-third native coal and two-thirds soft coal are used. In this state, coke, on a commercial basis, was first made in Jefferson County probably about 1861 or 1862. The coals used were the Steuben-ville Shaft, or Lower Freeport, and the Strip Vein or Middle Kittanning. The practice, however, was discontinued before 1880 because of the competition of superior foreign cokes. Beehive ovens, later built at Leetonia, Columbiana Co., were operated for only a few years; the coal used at this place is the Lower Kittanning or No. 5. In a desultory way, slack from the Pittsburgh coal has been coked at a few places in eastern Ohio, and attempts, either for experimental or for commercial purposes, have been made in other parts of the state. Small quantities of coke were made from the Upper Freeport coal at Salineville, Columbiana Co., and near Nelsonville, Hocking Co.; the results were poor. Tests were made of the Middle Kittanning coal near Zanesville, Muskingum Co., at Moxahala Furnace, Perry Co., and at Washington Furnace, Lawrence Co.; the cokes were all high in sulfur and ash. Attempts were made to coke the Clarion coal at Vinton Furnace, Vinton Co.; a small battery of molding ovens and a pile of high-sulfur coke yet remain to tell the story. The Pittsburgh coal was coked on a commercial scale at Utley and at Lathrop, Athens Co., but the operations were not successful and were soon abandoned. These failures and indifferent successes are not to be attributed to a lack of demand for a first-class coke, as Ohio has held a commanding place for many years in iron smelting; nor to a deficiency of coals, as the state has a vast reserve of such material. They are to be ascribed to the inferior quality of the native products offered to the trade. The cokes

Jan 1, 1920

By Richard F. Hinds, F. O. Reudelhuber

Application of the conventional depletion drive calculation methods to volatile oil reservoirs results in erroneous estimates of ultimate recovery. In view of the increasing number and importance of volatile oil reservoirs, a special technique has been developed which will result in more realistic predictions using laboratory data obtained from reservoir fluid studies of a specific type. The experimental data are designed to permit continuous material accounting and, therefrom, provide the hy-clrocarbon composition of both the flowing oil and gas phases. The resultant well-stream composition data are then used directly in surface recovery calculations utilizing equilibrium ratios. A step by step procedure, specifically designed for routine use by the practicing reservoir engineer, is presented in an appendix. An actual study performed on a deep Mid-Continent reservoir is used ay an il-lustrathe example. INTRODUCTION It has been a practice for many years to utilize the conventional ma- terial balance methods in conjunction with relative permeability concepts for the prediction of recovery from solution gas drive reservoirs.' Those who have performed such calculations recognize that compromises of several types are necessary in order to reduce the calculations to a reasonable degree of complexity. The most serious assumption involved results from the necessity of treating the produced oil and gas as separate fluids, independent of each other in their behavior. It is further assumed that the gas which is evolved in the reservoir as a result of pressure decline will not yield liquid upon the reduction of pressure and temperature resulting from production through surface equipment. Although these shortcomings have been recognized,' it has been difficult to attempt refinement of calculation procedures since the laboratory data available normally were not of the proper type or extent to permit such calculations. Three general procedures have been available for depletion drive calculations when laboratory fluid data are of the conventional type. Differential Procedure The most simple, and most widely used, method requires use of the formation volume factor and gas sol- ubility data obtained from a differential liberation performed at reservoir temperature. This procedure ignores the differences existing between the fluid behavior in the reservoir and its behavior as it is produced through surface separation equipment. The errors introduced are not serious when dealing with very low volatility fluids and this method may be utilized if the laboratory data indicate only slight differences between the differential data and the flash data obtained from separator tests. Modified Differential Procedure This method was developed when it became apparent that medium volatility fluids evidenced a wide difference between the flash and differential data. The differential data are adjusted by changing from a residual oil basis to a stock tank oil basis. All that is required is multiplication of the differential data by the ratio of residual oil to stock tank oil relative volumes existing for the original reservoir fluid at the determined saturation pressure. This procedure generally results in increased calculated ul-timate recovery; however, such results should be viewed critically. Upon examination it may become apparent that the results are influenced by errors in reservoir liquid

Jan 1, 1958

By G. S. Cole, G. F. Bolling

ThE exact type of fluid flow which occurs in a solidifying ingot is important in determining subsequent grain structure. This has been shown in studies of natural Convection" and of forced stirring or other disturbances of the melt."16 We shall explicitly argue that a complement to the existing natural flow in an ingot should be more effective than other types of flow in promoting the columnar-to-equiaxed transition. The ultimate effects of fluid flow upon structure is one of the topics of solidification that we have investigated in the alloy system Pb-Sb, under conditions simulating casting. In Fig. 1, the essential features of a bidirectional growth apparatus are shown; horizontal freezing from water-cooled faces within a low-thermal-conductivity lavite boat is a reasonable simulation of an ingot section. Details such as the furnace and thermocouples are omitted in order to show the location of four permanent. magnets, each with a pole separation of 21 in. providing a central field of about 1000 Gauss. When coupled with a dc current imposed through appropriate connections made at the cooled faces, a flow of fluid is produced as shown schematically. This technique described by Pfann and ~orsi" is ideal for our purpose since the flow indicated is the same as that we observe to occur naturally in this system. Components of 99.999 pct purity were used for study and all due precautions were taken in alloy preparation to avoid contaminants. Sections of the specimens were taken to ensure results representative of the interior as well as the surface of specimens. All proportions of equiaxed and columnar regions were measured by tracing the etched grain structures onto graph paper and simply counting squares. Four alloys were examined at superheats of 40" * 5°C and 100" * 9°C. Preliminary tests had shown that no appreciable enhancement of structure was obtained with magnetic field alone, so that this condition is not reported; it should nevertheless be noted that other configurations of magnetic field will reduce convection and thus enhance columnar growth.'8 For the tests reported the magnetic field was applied to a specimen by bringing the four preassembled magnets to a position 2 mm from an outer tube immediately after the ingot was poured. The dc current of 30 amps passed through the sample throughout the entire solidification cycle, resulting in a power dissipation of 9 w per sq cm of interface. This may be compared to the evolution of latent heat of approximately 18 w per sq cm. Table I contains the results of this experiment in terms of the total area ratio, equiaxed/columnar grains, as a function of the field interactions, solute concentrations, and superheats employed. The total structure of the ingot is seen to be most influenced when both the field and current are applied simultaneously; when current acts separately, little effect may be noted in spite of the heat supplied. In addition, the change in structure from the no field-no current case to the field-current condition is more pronounced at the higher superheat, and the higher the concentration of antimony. An example of the grain refinement, as well as the increased equiaxed zone, is shown in Fig. 2. It is now important to prove that there is indeed an increase in fluid flow due to the presence of the field-current interaction; this is done by temperature measurements in the liquid metal. Let us consider a bidirectional casting in which heat is applied to and removed from the system, in such a way that rate of solidification is zero.* When a sensitive thermocouple

Jan 1, 1967

By W. V. Bluck, W. L. McMorris

Higher coal quality is being recognized in potentially lowering the cost of power as measured at the bus bar. Assessment of potential coal supplies for most power plants is now going beyond buying at the lowest delivered fuel cost. It is now taking into consideration other factors, such as handling, storage, pulverization cost, boiler fouling, post combustion cleanup, and waste disposal costs. New measurements of quality are being considered now by those producing and those consuming the fuel by assessing numerous variables in the total fuel cycle to achieve the lowest possible power costs.

Jan 1, 1986

By Gordon M. Matheson, Charles V. Logie

The current state-of-the-art design of mine pillars can be grouped into empirical and numerical design techniques. Numerical design techniques are based on sophisticated computational techniques which analyze the stresses and strains through the interstices of a pillar. Empirical techniques are less exact, but have been widely used, particularly for coal mine pillar design, because of their ease of computation. Over the years numerous empirical equations have been proposed to calculate the ultimate strength of coal mine pillars. This paper presents a review of the various equations which are most frequently utilized and examines the fundamental assumptions, limitations and applicability of the design formulae. The review intends to provide the practicing mining engineer with an understanding of the assumptions and mathematical basis of each equation to aid in the selection of the criteria most applicable to his specific design problems. Recommendations are made of the empirical equations that are presently most acceptable for design.

Jan 1, 1983

By Paul A. Farrar, Louis P. Stone, Harold Margolin

The Ti-Mo-0 system was investigated in the region 0 to 45 wt pet Mo and 0 to 10 wt pet 0, from 600° to 1400°C. Solidus data are also presented. Isothermal sections at 700°, 900°, 1100°, and 1300°C, and vertical sections at 1 and 28 wt pet Mo, and 1 and 10 wt pet 0 are included. STUDY of the Ti-Mo-0 system has been carried out as part of a general study of titanium phase diagrams. The binary Ti-Mo system has been investigated in whole or in part by several investigators.1-8 It was found that molybdenum and ß-tita-nium form a complete series of solid solutions and that the ß/a + ß transus is depressed to below 600°C at approximately 30 pet Mo.* The Ti-O system has been investigated partially or fully in the range 0 to 30 pet 0 by several investigators." Extensive solubility of oxygen occurs in the field. While a is

Jan 1, 1957

By Theodore Simons

During the last half century a great amount of ingenuity and energy has been devoted to the invention of appliances for the recovery of valuable minerals from very fine sands and slimes. The reason for this is that in almost every dressing plant the greatest losses of values, considered relatively as well as absolutely, occur in the treatment of slimes. The natural aim of mill operators to minimize these losses has in recent years received another impetus, from the fact that the gradually diminishing occurrence of high-grade ores makes a more intense recovery of values from existing resources absolutely necessary for profitable operation. The results of such attempts are found in the appearance of a great number of machines and appliances which make it profitable to-day to rework old clumps, containing the tailings of older processes. A constantly growing difficulty of obtaining skilled labor and the increase in wages made it prohibitory to employ those types of machines which required much attention, and in the middle of the ninieteenth century the various concentrating tables of the percussion type, which automatically discharge their products, began to take the place of the intermittent tables, on which, when the bed had reached a certain thickness, operation had to be stopped in order to allow the skimming by hand of the separate layers formed on the table. In the course of years, two general types of machines evolved for the treatment of fine sands arid slimes: The so-called concentrators and vanners, on the one hand, and the buddles and round tables on the other.' For the profitable treatment of the very finest slimes, round tables have as a last resort proved more satisfactory and econoillical than other machines. In recent years they have agaiu become the subject of close inves-

Jan 1, 1914

By D. L. Pentz

The use of "probability" methods in slope stability analysis has been practised by geotechnical engineers for some time. This paper questions whether the term probability has been properly used since in many cases the term is used in a classical statistical manner only to describe frequency distributions of data. This paper proposes a definition of the term probability which includes the engineers' subjective state of confidence for all critical parameters. Such parameters may include the slope stability model, undetected structural features, strength, groundwater pressure distribution, and geological framework. This process does not make a "better" analysis but it does force the geotechnical engineer to state his opinion in such a manner that others can understand and if necessary, criticize the assumptions. Further, this technique forces the question, "What impact would failure of a slope have on the production schedule or costs of a mine?" The level of risk taken in adopting a particular slope design strategy in a mine is not a question of what Factor of Safety should be selected but, rather, what trade-offs result from steeper slopes and the associated costs of failure. This paper also presents several simple probabilistic techniques which, though widely used in other fields have been all but ignored in geotechnical slope stability analyses. These include the use of stratified sampling to optimize Monte Carlo uncertainty approaches, and the use of simple functional approximations rather than complex stability models in probabilistic analysis. The author presents a case example of this technique and discusses the results in comparison with more traditional methods.

Jan 1, 1983

By A. A. Collins

H. R. BIANCO*—I should like to ask Mr. Collins if that statement he made about the addition of drosses to the blast furnace slowing down the blast furnace is a result of his own experience or a result of the experience of some older metallurgists; and perhaps I should ask him to define the type of drosses that he means. A. A. COLLINS (author's reply)— That has been my own personal experience with dross. On various occasions at Chihuahua we attempted to incorporate the dross in our regular blast furnace charge and to shut down the dross re-verberatory to try to save some money. As expected, we had very poor results. I think that Ed Fleming will well remember on one occasion, that was back about 1933, when we attempted the first experiment along this line, and as a result of the sulphur addition to the blast furnace to matte out the copper we ended up with hanging furnaces and mushy slags and abandoned the dross experiment, once again turning to the use of the reverbera-tory for handling dross. H. R. BIANCO—Is that dross you refer to from the drossing kettle ? A. A. COLLINS—Yes, the dross that I am referring to came from drossing kettles. Furthermore, to back up my previous assertion, I had occasion in 1943, while up at Leadville, to once again experience the routing of dross through the blast furnace with its sulphur addition, since they had no dross re-verberatory, and to observe that once thf dross was removed, the furnace was speeded up almost 100 tons a day. All of these are personal experiences and I think that Mr. Feddersen also has had a little experience along this line —in fact, I believe all of us have had some experience. H. R. BIANCO—I know at Trail they recirculate considerable dross through the blast furnaces and we also recirculate dross at Herculaneuin and I am not aware that it has done much towards slowing down the blast furnace. A. A. COLLINS—We have always had very poor results. In the first place you have got to add a sulphur addition to pick up that copper and once you do that, that sulphur is apt to combine with some of the zinc and you are going to form a little mush; before you know it you have furnace hangs and a poor working furnace. Now of course that depends on the amount of zinc you have on charge. But in 1943, Leadville had roughly about 7 pet zinc in their slag and it worked very poorly. Previously when they had 4 or 5 pet zinc in their slag it did not matter. B. L. SACKETT* At Tooele we had a great deal of experience with copper. We have always been able to keep a lead well, however, in spite of the fact we have run as much as 5 pet copper and only 15 pet lead on the charge. But regarding the handling of dross, our dross reverberatory furnace is only 7 or 8 years old. Before that we recirculated the dross through the furnace and thought we were doing a pretty nice job. Of course these things are all more or less relative—in other words you establish a certain condition much better than one of a few years ago and possibly as good as any other of which you know and you think you have pretty good results. When we first took the dross off of the blast furnace and put it through the dross reverberatory furnace we immediately found out that we had gained something very real in furnace speed. Since that time there have been occasions when, because of the dross reverberatory being down, we have had to use dross again through the blast furnace and that has checked our original experience in slowing down the furnace very definitely. So we feel that a dross reverberatory is a very valuable asset at the Tooele Plant. A. A. CENTER*—Mr. Sackett's being here reminds me of trying to run with a minimum of lead concentrates the maximum of dross producing electrolytic zinc plant residue. He came up from International Smelting Co. to help us get started on that. We took an old copper blast furnace at Great Falls, Montana, and made a lead furnace out of it by putting a lead well on the other long side which of course is a very unorthodox lead blast furnace. Our aim was to treat the residue from the electrolytic zinc plant, as I said, with a minimum of lead concentrates. That meant a maximum amount of dross. At that time selective flotation was not general practice, so our zinc concentrates ran relatively high in copper and other dross-producing elements; and of course these were largely in the zinc plant residue. I think we might call it muscle metallurgy, but we had an interesting, successful experience there and we ran for over a year thanks to Mr. Sackett's helping us get started. I have the details, but time does not permit. We did well enough so that the A. S. and R. Co. at East Helena kept boosting up the offer to us for the electrolytic zinc plant residue and there was not enough lead concentrate to supply two lead smelters there in Montana, so the matter finally finished up by the A. S. and R. Co. taking all of the residue under long term contracts.

Jan 1, 1950

By I. N. Knapp

Foreword I HEREWITH present some notes on the use of Portland cement to cement in the casing, and for plugging, to exclude water from oil and gas wells, and the methods employed. I have used my best efforts to make each step of the operation of cementing wells perfectly clear. The information is the result of actual experience and observation. The illustrations are from original drawings made especially for this paper. Portland Cement It is not necessary to discuss here the manufacture of cement. Any established brand of the slower setting Portland cements may be purchased with the confidence that it will harden, if properly used, and exclude water from and plug wells efficiently. Setting.-By the setting of cement is meant its initial change from a soft or plastic mortar to a friable solid. After the cement has become thoroughly set it is still very weak and can be readily pulverized in the fingers. Setting is thought to be effected by the crystallizing out of the silicate and the aluminate of lime, which are soluble in water in their anhydrous form. After dissolving in the water they pass to the hydrated state, in which they are insoluble, and hence are precipitated in a crystalline form.

Jan 3, 1914

By Stephen E. Merritt, T. Carl Shelton

Surveying and mapping are used to locate and visually portray objects, lines, or areas in relation to a reference point or line. The actual making of the measurements to locate the objects and points falls under surveying while mapping is concerned with putting the survey information into a graphical form. Generally, the type or class of proposed survey depends on the precision required. Some surveys may need only approximate measurements which can be obtained by simply pacing or by using an ordinary measuring tape; others may require much accuracy, thus calling for the use of an engineer's transit or theodolite along with a graduated steel tape for horizontal measurements, or a level and a graduated rod for measuring vertical distances. Mapping is likewise dependent on accuracy requirements. For example, a general layout showing the relative position of surface facilities may not call for a large scale of dimension or great precision whereas for detailed work, a large scale plus care in plotting points and drawing lines and curves are important factors. SURVEYING METHODS There are many kinds or types of surveying methods. Some examples include: land surveying for determining boundaries of land areas ; route surveying for locating roads, highways, right-of-ways, and haulways; city surveying for laying out lots, streets, and alleys ; and mining surveying for projecting mine openings and locating mining operations. There are other types of surveying than those named, but in general, the type of method to be used will depend on the purpose for which the survey is to be made.

Jan 1, 1973