Search Documents

By R. A. Pasternak, B. Evans

A dynamic technique for the determination of solubilities of gases in metals has been explored, using the N-Nb system as a test case. An initially clean sample, maintained at constant high temperature, is exposed to the gas at low pressure: the rate of sorp-tion and the corresponding change in sample resistance are measured continuously. A pronounced decrease in the slope of the resistance concentration curve is observed at the terminal solubility. The rate of gas uptake by the sample was determined in an ultrahigh-vacuum flow system equipped with a servo-control which maintains constant pressure in the sample chamber; the system and the technique have been described in detail elsewhere. 1,2 The sample was held at constant temperature during sorption by maintaining approximately constant power input into it; this results in constant temperature, since the emissivity of a metal is independent of moderate concentrations of dissolved gas. The simple electrical circuit used both for heating and for resistance measurement is shown in Fig. 1. The power input into the filament is where R is the filament resistance, RL is an adjustable resistance in series with the filament, and VT is the constant dc potential of the power source. If RL is set equal to R at the beginning of an absorption run, the power input becomes insensitive to subsequent resistance changes; for example, an increase of 20 pct in sample resistance is accompanied by a decrease in power input of less than 0.8 pct; i.e., the

Jan 1, 1967

By J. J. Arps

This paper reviews the methods currently in use for estimating primary oil reserves and discusses the principles on which these methods are based. Particular emphasis is placed on how these methods change with the type of information available during the life cycle of an oil property. This paper contains various novel estimating methods and shortcuts heretofore unpublished. INTRODUCTION Estimating oil reserves is one of the most important phases of the work of a petroleum engineer since the solutions to the problems he deals with usually depend on a comparison of the estimated cost in terms of dollars, with the anticipated result in terms of barrels of oil. His recommendations to management regarding the best course of action are therefore normally based on the most favorable balance between these two. Specific engineering problems which require such a knowledge of recoverable oil reserves and a projection of future rates are: [a.] the exploitation and development of an oil reservoir; [b.] the construction of gasoline plants, pipelines and refineries; [c.] the division of ownership in unitized projects; [d.] the price to be paid in case of a sale or purchase of an oil property, and the magnitude of the loan which it will support; [e.] the proper depreciation rate for the investment in oil properties; and [f.] evaluation of the results of an exploration program. This discussion will be confined to the various methods and tools which are currently in use for estimating oil reserves to be obtained during the primary phase of an oil-producing reservoir and for a projection of the future production rates. Reserves which may be obtained by secondary recovery methods or fluid injection programs and gas and gas condensate reserves will not be discussed in this paper. Unfortunately, reliable oil reserve figures are most urgently needed during the early stages when only a minimum amount of information is available. Management's interest in the oil recovery from a property—aside from its use for accounting purposes—usually declines when the property approaches its economic limit, just at the time when the reliability of the estimates is at its best. To illustrate this general idea a chart is presented (Fig. 1) showing the three periods in the life of an imaginary oil property. Time is shown on the horizontal axis, while the cumulative production and estimated ultimate recovery are plotted vertically. No particular units are used and this schematical chart is not to scale. During the first period, before any wells are drilled on a property, any estimates will of necessity be of a very general nature, based on experience from similar pools or wells in the same area, and usually expressed in barrels per acre. This will

Jan 1, 1957

By J. Ehner Thomas, M. D. Gould

Until four years ago the market price of oil securities moved directly and immediately with the general list. This point, was first developed by the senior author in 1924 while making a statistical study of the relative movement of oil securities and the general market. Plotting the monthly averages of 17 oils against 233 industrials disclosed the sur- prising relationship shown in Fig. 1. The traditional vagaries of the oil business, the wide fluctuations in current supply and resulting abrupt changes in crude prices nevertheless produced no movements in the market price of oil securities as a group, which departed notably from the movements of the general market. Obviously general business conditions did not always change when and as conditions in the oil industry changed; clearly the fluctuations of

Jan 1, 1929

By J. J. Frawley, W. J. Childs

The dynamic nucleation of supercooled bismuth and Bi-Sn alloys has been studied over a frequency range of 15 to 20,000 cps. For low-frequency vibration, a minimum vibrational energy was required for enhancement of nucleation. Above this critical energy, the dynamic supercooling was less than static supercooling showing that vibration promoted nucleation. The amount of dynamic supercooling continued to decrease with increasing vibrational energy until a minimum or threshold value was reached. This minimum value of supercooling for nucleation remained constant joy all further increases in vibrational energy. For higher frequencies, similar results were observed. This behavior has been related to the necessity of cavitation for dynamic nucleation. When a liquid is cooled to a temperature below its equilibrium melting point, the solid phase is more thermodynamically stable. However, for solidification to occur, a two-step process, nucleation and subsequent growth of the solid phase, must occur. When a liquid is supercooled, that is cooled below the equilibrium melting point, the controlling process for solidification to begin is the rate of nucleation. Once nucleation has occurred, the solidification process is controlled by the rate of growth. Nucleation can be induced by two factors: either by a catalyst or by the use of mechanical shock. Numerous investigators1-4 have studied the effect of nucleation catalysis but much less systematic study has been made of nucleation by mechanical shock waves. The influence of vibrations on grain size in castings and ingots has been studied by many authors but no clear understanding of the mechanism or accurate prediction of the effect has been presented.5 It would be intuitively expected that the further the departure from equilibrium (i.e., the greater the supercooling), the easier it would be to induce nucleation. This has been quantitatively demonstrated both by walker6 and later by Stuhr,7 that the greater the degree of supercooling the easier it is to nucleate by a shock wave. Stuhr also attempted to obtain the mechanical energy required for nucleation of bismuth as a function of supercooling. He vibrated a crucible containing supercooled metal at low frequencies and various amplitudes and noted the corresponding dynamic supercooling obtained. The amount of supercooling was inversely proportional to the mechanical energy applied. Limitation of his experiment was the problem of the confinement of the liquid in the crucible without splashing and minimizing other unwanted modes of vibration. Tiller et al.8,9 did similar work on tin and Sn-Pb alloys using an electromagnetic stirring device. Their conclusions were that the magnitude of the magnetic field strength did not affect the amount of undercooling at which nucleation was initiated. While conclusive experimental results have been lacking to explain this effect of mechanical vibration on inducing nucleation, a number of theories have been proposed. Two of these theories are discussed below. 1) The Change in Melting:- Point Locally Due to the Change in Pressure (Clapeyron Equation). According to Vonnegut10 the most plausible explanation for the nucleation of a supercooled melt by cavitation is the effect of changing the melting point by a change in pressure. For materials where the volume decreases on solidification, an increase in pressure raises the melting point; for materials which expand on solidification, the melting point is raised for a decrease in pressure, i.e., rarefaction. Using the Clapeyron equation, the melting point of a metal can be calculated as a function of pressure. If it is assumed that the equation can also be used to calculate the temperature of nucleation of a supercooled melt as a function of pressure (i.e., the temperature of heterogeneous nucleation will increase with pressure at the same rate as the melting point), the amount of supercooling required for nucleation will be constant at all pressures as shown in Fig. 1. It is obvious that an isothermal change which results in an increase in melting point results in an equal increase in supercooling. This increase in supercooling may now be sufficient for nucleation. A pressure of 80,000 atm was calculated, using the Clapeyron equation, as the pressure required to increase the temperature of nucleation of nickel by 200°C. According to Lord Rayleigh,11 this very large pressure could be generated for a very brief period of time by the collapse of a cavity. This pressure wave is radiated in all directions from the collapsed cavity. If the temperature of the melt is slightly below its equilibrium melting temperature at atmospheric pressure, stable growth can follow; that is, once nucleation occurs, growth becomes the main driving force of the solidification process. This proposal has been extended to water which expands on freezing by assuming that nucleation occurs during rarefaction following the pressure pulse. This negative pressure pulse should follow immediately after the positive pressure pulse with its magnitude approaching the critical tensile strength of the liquid. The negative pressure developed during this period would raise the melting point of water and thus promote nucleation. Hunt and jackson12 have suggested this for water. Similarly, it could be postulated that bismuth which also expands on freezing could be nucleated during the negative pressure pulse. 2) Nucleation by a High-pressure Phase. An extension of the Clapeyron equation to systems where density decreased on freezing at atmosphere pressure has been proposed by Hickling.13 The phase diagram for water initially shows the well-known decrease in

Jan 1, 1969

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By Charles Ramseyer

THE manufacture of iron and steel is one of the largest of our indus-tries; and in point of size of single plant and equipment certainly the biggest of all industries. By the general public it is generally con-sidered a prime example both of the marvelous technical advances achieved by modern science and engineering in the design and operation of equipment and of the efficiency of big business in the coordination of men and materials. Actually the operation of its basic processes has not changed significantly in either theory or fundamental design of equipment in the past 75 years. Though many other process indus-tries have been born and developed, and not seldom completely revolu-tionized, during this period, the primary processes of making iron and steel are still carried out along the lines laid down, and in the equipment originated so long ago, by Bessemer, Siemens and Martin, and subse-quently expanded to practically the modern scale by Carnegie, Schwab and Captain Bill Jones in the eighteen eighties and nineties. The application of the principles underlying the continuous counter-current physical and chemical interaction of solids, liquids and gases, which have been so successfully used in the rapid evolution of our chemical process industries, has been very largely lacking in the steel industry. In the days of -the last-named giants, especially Carnegie, the steel industry made great and rapid technical progress. Carnegie's ever driving idea (as later with Ford in the production of automobiles) was the finding of new and better ways of making cheaper steel. Carnegie himself was a steelman, and so long as he dominated the industry its technical progress. was rapid; and he, like Ford, was vastly successful financially as well, since his costs were continually being driven lower than those of his competitors by his advances in steelmaking technique.

Jan 1, 1934

By Joseph E. Pogue

Any mechanism, either natural or artificial, for regulating the functioning of a given unit in the general economy must operate toward the maintenance of equilibrium if it is to survive. The petroleum industry, concerned as it is with the production of a natural resource of specialized character, is surrounded not only by the economic factors common to other industries but by an extra set of unique elements centering about the fugitive character of crude petroleum under conditions of competitive development. The term equilibrium, therefore, so far as the oil business is concerned, involves a combination of economic and physical factors: the first set having to do with supply, demand, costs, profit margins, purchasing power, and the like; and the second, with underground pressures in oil pools, efficient rates of extraction, and all other aspects of engineering that may be summarized by the familiar term "conservation." The two categories, in fact, are not as clearly divided as the foregoing statement would imply, for in practice it will be found that the economic and physical aspects have a pervasive interaction and interrelationship. If the development of the petroleum industry in the United States is examined from its inception in 1859 down to the present, it will be found that, beginning about 11 years ago, a new mechanism for regulating the production of crude petroleum made its appearance. Prior to this recent period, the production of this raw material was determined by competitive forces operating without outside restraints. At present the output of crude oil is subjected to supervision by regulatory bodies in most of the oil-producing states, which impose upon the operators certain conditions having to do with the manner and rates of production. Thus, in the space of a decade, the mechanism for producing crude oil has changed from an automatic to a designed procedure called proration. And in its short history this method has been marked by a rapid evolution in its nature and incidence, with progressive changes still under way.

Jan 1, 1938

By N. A. Ziegler

THE present publication is a continuation of the work on gas analysis, described in a paper presented before the Institute of Metals Division a year ago.1 While that paper was largely descriptive in character, dealing with the various parts of the apparatus and method of operations, the present one gives numerical data obtained as a result of a series of experiments with iron-carbon alloys. The apparatus and the methods applied are essentially the same as previously described, changes being only in minor details. Attention should be called to the fact that in the present work we are dealing with the gaseous mixtures obtained as a result of vacuum melting of various ferrous alloys. It should be understood that when the terms "degasified sample" and "products of degasification" are used, they refer to the sample remaining after the vacuum fusion of the alloy and the gaseous products removed therefrom, respectively. The writer does not wish to create the impression that the metallic products of this process are absolutely free from any gaseous elements, nor that the gases obtained are present as such in the original sample. These two points are not yet definitely known and are subjects for future investigation. The point, however, which has been established beyond doubt, is that all the gases dealt with come from the metallic charge and are present either in the charge as such, or are produced as a result of chemical reactions going on within the charge. The suggestion that the gases are due to the reactions between the metallic charge and the refractory materials has no valid basis.

Jan 1, 1929

By P. C. Kapur

A principal first-order and a minor summation term contribute to the solution to the discretized batch-grinding equation when formulated in cumulative retained mode. Depending on the inter relations hips between the selection and breakage parameters, the minor term may be advantageously modified in a number of ways. The reduced grinding equations thus obtained are solved by iterations to give relatively simple solutions which are tested against experimental data. The irn-plications and advantages of the reduced grinding equations are briefly discussed. In many instances, the trajectory of the particle-size distribution in a batch mill may be extracted from a set of particle mass balance equations as follows

Jan 1, 1971

By M. W. Strong

The technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in formation, the type of problems, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differential pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all materials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improvement of material and its most efficient use has to be carried out. In this paper will be discussed the main mud problems of Iran, some of which are peculiar to local conditions while others are of the general type common to all workers in this subject. Underground Conditions In deep wells in Iran the normal overburden may consist of: (1) up to several thousand feet of marls with interbedded sandstones and limestones of varying porosity and permeability; (2) beneath this a chemical series of rock salt and anhydrites, containing various marls and thin limestones,

Jan 1, 1939

By M. W. Strong

The technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in formation, the type of problems, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differential pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all materials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improvement of material and its most efficient use has to be carried out. In this paper will be discussed the main mud problems of Iran, some of which are peculiar to local conditions while others are of the general type common to all workers in this subject. Underground Conditions In deep wells in Iran the normal overburden may consist of: (1) up to several thousand feet of marls with interbedded sandstones and limestones of varying porosity and permeability; (2) beneath this a chemical series of rock salt and anhydrites, containing various marls and thin limestones,

Jan 1, 1939

By C. L. Dake

Residual deposits occur both as products of weathering and as products of hydrothermal decay. Products of Weathering That climatic conditions affect greatly both the rate and the results of weathering, is shown in temperate, polar, arid, and tropical regions, each of which will be considered separately. Weathering under Temperate Climates The decomposition of any rock is accomplished by the removal of the more soluble bases, and a concentration of the relatively insoluble oxides of iron, aluminum, and silicon. By reason of its somewhat greater solubility, silica is much more subject to removal than iron and alumina. The two important residual end products of weathering are sands and clays, the former consisting essentially of quartz, and the latter of kaolin and limonite.l When such deposits are formed in situ, the sands and clays are not separated, but remain as mixtures, which can be more or less perfectly separated by treatment with water. In such a separation, the ferric oxide or hydrate tends, by reason of its fine state of division, to remain with the clays and silts rather than the sands. While ferruginous sandstones are everywhere common, they are rarely rich enough in iron to become an ore without secondary concentration. Since the silica of these sandstones is completely crystalline quartz, it is much less liable to removal by solution than are the more soluble forms of partly amorphous chert and jasper, which have been removed on so large a scale from the Lake Superior iron formations.2 Moreover, the iron cement of sandstones, which constitutes the chief iron content of these rocks, is often a result of later infiltration, and not of original sedimentation. Thus if clays rather than sands contain the iron of residual decay,

Jan 1, 1916

By I. N. Zavarine

Austenite is often defined as a solid solution of carbon or carbide in a nonmagnetic form of iron. Conversely, magnetic measurements are often used by investigators for the purpose of detecting the degree of austenite decomposition after an iron alloy has been subjected to certain thermal or mechanical treatments. Association of the magnetic state with the gamma-phase decomposition is often extended to the alloys of iron with elements other than carbon. Definition of austenite as a nonmagnetic solid solution cannot be accepted in the light of available information without certain reservations. The relation of magnetic transformations with the gamma-phase decomposition in the complex alloys of iron has never been rigorously proved. The present investigation deals primarily with the magnetic transformation that occurs in carbon steels during the quenching process. The work was further limited to a study of magnetic transformation in carbon steels quenched at such rates as are necessary to retain the product of austenite decomposition in a martensitic state. Peevious Work Considerable information has accumulated in the literature with respect to the magnetic transformation in alloys of iron, but nearly all of it relates to transformations under the conditions of equilibrium between the phases of the alloy. Earlier studies of Hopkinson,$(') Curie,(2) and Honda'~) are well known. Investigations of the magnetic

Jan 1, 1934

By E. G. Leonardon

THE object of this paper is to describe briefly the practical results obtained in several problems of civil engineering by resistivity measurements of the underground. It is intended for the mining engineer, as well as for the construction engineer; the stratigraphical problems discussed are general and frequently are encountered in mining exploration. Resistivity measurements have been used in mining and oil exploration for a number of years.1 Their introduction in the field of civil engineering, on the contrary, is rather recent. It was applied for the first time in the spring of 1928 near Littleton, N. H., in the survey of two dam sites for the New England Power Assn .2 Since then, the geophysical firm with which the author is connected has had an opportunity to develop this field of activity, and more than 20 investigations at dam and tunnel sites have been carried out in the United States and Canada. A part of this work has been verified by underground or drilling exploration. This paper deals with but a few of the results, which we are permitted to make public now. The theoretical and technical sides of the processes employed will not be discussed; they have already been described in various technical. .publications. A few general points will be mentioned, to make clear the practical examples given.

Jan 1, 1931

By H. Van F. Furman

As the cyanide-method for the extraction of gold from ores is extensively used in the United States and elsewhere, and appears destined to prove a factor of increasing importance in the metallurgy of gold, a description of the latest laboratorymethods may prove of interest. The history of the development of the process in the United States has been analogous to that of all new processes. Many failures are to be recorded and a few successes. It is the opinion of the writer that, had the following simple tests been better understood, many of the failures would not have occurred, and we should probably have a larger number of successful plants in operation. While the process is not simple, but requires a high degree of chemical and engineering skill, the determination of the adaptability of an ore to the method is generally not difficult. While the laboratory-results will not always coincide with the actual results obtained in the mill, they will serve as a guide and control on the working of the mill, and mill generally suffice to determine if the ore can be

Jan 1, 1897

By Raymond Howe

SOME time ago,, a prominent engineer asked a representative of the firebrick industry to prepare a comprehensive paper on blast-furnace refractories. It was to have been the purpose of this paper to gather practical experiences from widely different sources, in the hope of determining what kind or kinds of firebrick were best adapted for certain uses. This engineer sent questionnaires to the large consumers of blast-furnace linings and stovebrick and received very detailed replies as to their experiences. These replies are conflicting, but, having been turned over to the writer, form the basis of this attempt to meet the request. Because of the impossibility of making final recommendations at this time, a few of the more interesting and commonly known methods of studying refractories are also discussed, as well as the more recent developments in this field. The first reply to, the questionnaire stated that good service was being secured from the linings. This satisfactory condition was attributed to the use of a very good distributor. The writer believed that manufacturers try to and do produce a good product and that the proper handling of equipment is of the utmost importance, if good results are to be secured. The type of bricks used was not mentioned. The second reply stated that good life was secured from the furnace linings, but that the writer had had soft-fired stovebrick crumble and, for that reason, preferred a hard-fired product for use in this position. The type of bricks used was not mentioned. The third reply stated that firebrick had crumbled from the mantle up; the cause was not known. The fourth reply stated that the stove linings were satisfactory. Hand-made furnace linings failed after 4 years' service so a steam-pressed lining was installed which was still good after 4 years of service. Consequently, a second steam-pressed lining was installed but this disintegrated at the top after the furnace had been in- blast 7 months. The firebrick manufacturer attributed this failure to the expansion of iron blocks that had been installed at the stock line to prevent erosion.

Jan 9, 1919

Jan 1, 1889

By R. H. Pemberton

The principle of airborne electromagnetic prospecting is well-known. The basic geophysical texts in most cases discuss the main elements involved in electromagnetic prospecting. However, there is certainly little information available to the public concerning the present types of airborne electromagnetic systems being flown today by both contracting companies and some of the mining companies which have their own instruments. This is unfortunate since it is difficult for those people not conducting such operations to understand thoroughly the large variation in the electromagnetic instruments available.

Jan 1, 1961

By Otto F. Pfordte

The silver-ore-deposits of the famous district of Cerro de Pasco were discovered in 1630 by Huari-Capcha, an Indian shepherd. In the early part of its history, the district yielded enormous riches. The records from 1784 to 1846 (excluding five years, 1821-25, during which civil war prevailed) show a product of 2,323,526 lbs. of silver; and the value of the total product since the discovery may be estimated at about $565,000,000. The town of Cerro de Pasco is situated in the province of the same name, department of Junin, Peru, 14,250 feet above sea-level. The nearest railway station is on the line of the Callao and Cerro de Pasco R.R., at a distance of about three days' travel on horseback. The population of the town numbers about 6000, mostly native Indians. Mines.—The mines are mainly located in the immediate neighborhood of the town and partly even under the principal streets, being distributed in several very large open cuts 250 to 350 feet deep called tajos, which extend in a nearly direct north and south line west of the town and are known as Tajo de Santa Rosa, Tajo Tingo or Portachuelo, Cajac Graude, Cajac Chico, Salsipuedes, Avella Fuerte, and several smaller ones. Tajo de Santa Rosa, the largest and most southerly, is closely connected on its north side with Tajo Tingo; while the others are entirely separate and lie northward in the order given ; the extreme ends of the series being about a mile apart. Besides these, there are Tajo Descubridora a short distance east of Sta. Rosa and Tajo Matagente, about half a mile north of the main plaza in the town of Cerro de Pasco. The argentiferous deposit consists mainly of a ferruginous sandstone, while the neighboring country-rock is limestone, conglomerate and slate. The judicial fixed point from which all mining claims are measured, is a cross erected on a small elevation east of, and between tajos Sta. Rosa and Tingo, called Santa Catalina. This important

Jan 1, 1895