Search Documents

By Robert K. Warner

When a new mine is opened, and often when an operating mine must adapt itself to physical or economic changes, a mining system must be selected in complete detail. In the past the plan chosen was usually the product of the local staff alone, however limited the training and experience of that staff might be, which often resulted in the introduction of methods that were familiar to the staff, but not so well suited to the conditions as others unknown to the local men. A new management, noting the difficulties with the existing layout, might make modifications or complete changes, so that many mines in their history have seen a whole series of mining systems, each somewhat laboriously grafted on to its predecessor. This should not be interpreted as a condemnation of the older staffs for sticking to the tried systems, such as open square-sets in the early days at the Homestake, because they knew it would work after a fashion, nor does the statement apply to the technically trained, and usually broadly experienced staffs of most present-day properties. The older miners did not have the variety of tools and methods, nor the present freedom of transfer of information as to what the other man is doing, and so did the best they could under the circumstances. Finally, the higher grade of the ores made the choice less vital. The ever-increasing need to mine low-grade orebodies, with a fixed or even lower price for the metal produced, has caused an increasing need for low-cost mining. In most new mines this has simplified the problem of selection by eliminating from consideration all of the high-cost systems, but it has also complicated the choice by the necessity for refinement in detail and a close adjustment of the plan selected to all the conditions at the property. In these low-cost problems any textbook division of mining systems as applied to "beds, veins or masses" avails little as a guide. It should be realized at the outset that to be successful under modern competitive conditions a system of mining must be worked out with elaborate detail, with careful time scheduling and control of the various elemental operations, and that after it is introduced it must be run with a large amount of technical direction.

Jan 1, 1934

By W. A. Thomas

Steam is, and doubtless always will be, the basic power in the anthracite industry, either directly applied through engines and pumps or electrically. The rapidity with which electric power is being applied to the mining and preparation of anthracite leaves little doubt as to its utility and economy. There is practically no operation, except possibly the drilling of hard rock, that has not been successfully electrified and the matter of drilling is handled economically with electrically driven compressors and the standard compressed-air drills. Conservation and the seemingly ever-increasing cost of production, justify careful consideration of the possible results of the more extensive use of electric power in the industry. It is not planned to discuss, herein, the relative economies of individual applications but to consider the relative economy and flexibility of steam and electric power. The reports available for the year 1920 indicate a production of slightly over 80,000,000 tons of anthracite, of which 8,843,500 tons were used for power and heating purposes; in other words, over 11 per cent. of the production was used at the mines. Some of this was used to generate electric power at the mines, about 160,000,000 kw-hr., while 150,000,000 kw.-hr. was purchased from the public utility companies. One large producer, who is buying some electric power and generating some, used over 13 per cent. of the production for power and heating at the mines. Another producer, where considerable electric power is generated on the properties, is using less than 9 per cent. of the output for power and heating. One of the largest producers has a fuel consumption of over 15 per cent. of the output, besides which considerable power is purchased. A careful study of the field indicates that steam-operated plants use upwards of 13 per cent. of the production for power and heating, while electrically operated plants use about 1 per cent. for heating; so that, for steam-power purposes at least 12 per cent., or 268.8 Ib., are used for power out of each ton produced. In the complete electrification of anthracite mining operations, no set rule can be given for the power requirement, in kilowatt-hours per ton, as conditions vary widely in the matter of pumping, ventilation, and transportation, but the following cases are given as a basis of determining a range and a possible average power requirements:

Jan 1, 1922

By Kenneth Robertson

THERE is probably less known of this subject than of any other connected with the metallurgy of iron. In all the books that treat of this matter, there ore given analyses of slags, their chemical formulae, the loss of iron, etc. ; but few, if any, give the character of the iron mode at the time; none give analyses and physical characteristics of the ores and limestones used, and they present merely isolated examples from various furnaces, and consequently one is more frequently puzzled than enlightened after reading them. During two years I have had occasion to analyze the slags and many of the pig-irons from two furnaces, and for this article I hove made analyses of all the different grades of pig mode by them. A

Jan 1, 1873

By M. E. Volin, F. H. Erbisch, G. M. Wenberg

Bacterial leaching of copper and uranium is practiced under acidic conditions in environments furnishing sulfur and iron. However, many mineral deposits do not have these conditions; the chalcocite and native copper deposits in Michigan's Upper Peninsula are examples. Species of bacteria and fungi isolated previously from samples taken at the White Pine Copper Co. tailings pond and mine, were screened for solubilization of copper from chalcocite ore and flotation concentrate and from native copper jig concentrate. Certain Penicillium species solubilized significant amounts of copper under neutral to slightly acidic conditions in a carbon and nitrogen-enriched medium. Leaching apparently was accomplished by release of metabolites which chelated with the copper. The copper yield was highly dependent upon the medium composition and the concentration of copper in the source material. The standardized procedures which were developed in an attempt to maximize copper yield in leaching times of three to five days are described. This preliminary research indicates a biological leaching process for copper which is different from those in use, but whether it can be applied economically remains to be determined.

Jan 1, 1972

By ElRoy Nelson

WATER provides to many mineral industries functions similar to those performed by money in the economic system. Water is a medium of exchange. It is also required in chemical reaction for cooling, for transfer of minerals, and for cleaning. To a great extent, water is also a raw material in almost every industrial operation; it becomes a component of the finished product. In the Rocky Mountain region, water is treated with a great deal of respect. There has not been enough of it when needed. Long ago storage facilities were planned and devised to assure a supply during periods of shortages. This comes from the history of the region in irrigation and mineral processing. Within this region the shovel was always the most lethal weapon used in settling disputes over the use or misuse of water.

Jan 10, 1954

By G. R. Countryman, G. H. Thomas, I. Fatt

Miscible displacement in both thewetting and non-wetting phase has been studied in two-phase systems. Experimental data show that dispersion is a function of saturation and cannot be predicted from dispersion theory developed for single-phase miscible displacement. Some of the effect of saturation on dispersion is a result of the development of dead-end pores or a dendritic pore structure in multiphase systems. The presence of dead-end pores or dendritic structure is confirmed by pressure transient studies. INTRODUCTION Displacement by flooding with a miscible liquid is a possible means for recovering the estimated two-thirds of the oil that remains behind after primary production. The immense economic importance of a process that can recover such large quantities of oil has led to extensive laboratory studies of miscible displacement. As usual in production research, most laboratory studies of miscible displacement have not attemped to reproduce all of the conditions existing in a petroleum reservoir. In the early stages of investigation the need has been for information on the broad, basic principles of the phenomena involved in miscible displacement. The effects of overburden pressure, reservoir temperature, and wettability have been considered of secondary importance. However, one property of a petroleum reservoir which is expected to be of major importance and yet has been omitted from many laboratory studies is the presence of interstitial water. Two possible effects of interstitial water on the displacement mechanism in the hydrocarbon phase immediately come to mind. First, from the general1y accepted theory that capillarity governs the distribution of oil and water in porous rock one would expect that for water-wet rock the water will be in the small pores and oil in the large pores. A miscible displacement of oil carried out in the presence of water is operating in a pore size distribution shown in Fig. lb, whereas if the same test had been performed with only one phase present the pore size distribution is as shown in Fig. la. Although there is not yet a theory of miscible displacement which explains in detail the effect of pore size distribution, one would expect the differences between Figs. la and lb to influence the displacement efficiency. A second factor which may make a multiphase system different from a single-phase system is the presence in the multiphase system of dead-end pores or dendritic structure. Experiments of various kinds on reservoir rock have led to the belief that all pores in the network structure of a porous rock take part in conducting fluid during single phase fluid flow.1,2 There are then no dead-end pores and no fingers or dendritic structures containing stagnant fluid. In a multiphase system, however, the second phase may

By J. G. Hadley

IN THE early stages of the depression the Utah Copper Co. realized that an unemployment problem would he created which demanded an intelligent and sympathetic solution. The company recognized that as many men as possible must be kept at work on a basis which would ultimately permit of the most efficient reabsorption of displaced labor. The company therefore determined to distribute available work among the greatest number of men and to that end adopted a system of rotating employees on a part-time basis. An employer requires a certain number of days' or shifts' work during the month. Obviously one employee working thirty days or shifts a month is equal to two employees each working fifteen. In principle, therefore, where two employees equally fitted to do certain work are available the work could be divided between them on an equitable basis and twice as many persons would benefit. A rotation plan on this basis was adopted by the Utah Copper, Co. on Jan. 30, 1930. Some variations of the orig¬inal plan have been made from time to time, the reasons for which will be discussed.

Jan 1, 1932

By H. L. Ames, P. H. Jennings, R. W. Stanley

A process has been developed for leaching copper, lead and calcium from molybdenite concentrate. The leachant is a solution containing an oxidizing chloride (e. g., CuC12, FeC13) and an alkaline earth metal chloride (e. g., CaC12). Cupric chloride and ferric chloride, in the presence of 20-30% calcium chloride, are effective oxidants for chalcopyrite and galena. Calcium chloride, in addition to promoting the rate of leaching, serves to lower the solution pH and raise the boiling point. Leaching for two hours at 110'~ with a 1 % CuC12-10% FeC13- 30% CaC12 solution results in the extraction of up to 98% of the copper in molybdenite, 98% of the lead, and 79% of the calcium. Less than 0. 5% of the molybdenum is dissolved. The leach solution can be rapidly and effectively regenerated with gaseous chlorine and recycled. Build-up of copper and lead in the leach solution is controlled by discarding about 30% of the leach solution each cycle.

Jan 1, 1973

By D. N. Stevens, D. N. Bloom, M. A. Klugman

This paper represents a portion of a larger study concerning dispersion of major, minor and trace elements in wall-rock about orebodies in part of the Colorado Mineral Belt. This phase of the work pertains to the Mg/Ca ratio variations in wall-rock adjacent to orebodies in two mines, one in the Horseshoe Mining District (Hilltop mine), and the other in the Alma Mining District (Phillips mine). The two districts lie adjacent to one another, the Horseshoe District on the south and the Alma District on the north, and are commonly referred to as one, the Alma-Horseshoe Mining District. The Alma-Horseshoe Mining District is located 80 miles southwest of Denver, Colo., (Fig. 1) in Park County, on the eastern slope of the Mosquito range. The area is typified by rugged relief with altitudes of from 10,500 to 14,000 ft. The Horseshoe District is separated from the Lead-ville Mining District by the crest of the Mosquito range, with the Leadville District to the west. The Alma-Horseshoe District has been considered as peripherial to the Leadville District, and has not received the detailed attention that the Leadville District has. These two mines were selected for this study because of their ease of access; the attitude of the workings and the drill holes to the known mineralization; the similarity of the mineralization; and because the mineralization occurs in carbonates in both mines but are of different ages. In the Hilltop mine mineralization is confined to the Leadville dolomite (Mis-issippian) and is principally lead with subordinate zinc and silver. In the Phillips mine the mineralization occurs in the Peerless dolomite and shale (Cambrian) and in the Manitou dolomite (Ordovician) and is principally zinc with subordinate lead, silver,

Jan 1, 1964

By W. N. Page

The Red-Ash colliery was the scene, March 6, 1900, of an explosion by which some fifty men were killed or wounded, and much property was injured or destroyed. On March 19th, the earliest date at which entrance was practicable, I examined the mine with the view of determining the extent, cause and point of origin of the explosion, and with the permission of Mr. F. Howald, the manager, and the owners of the property, for whom the examination was made, I present in this paper some results of that examination, comprising the essential portions of my report to them. Location and Plan of the Mine. The Red-Ash colliery, situated on the south side of New river, next below the Rush Run mine, with which the underground workings are connected, is a drift-mine, the entrance to which is on a slope, about 500 ft. above the river. (Fig. 1 is a plan of the workings, in which the points where human bodies were found are designated by numbers.)

Jan 1, 1901

By Edwin A. Sperry

At the request of some of my engineering acquaintances, to whom the results became known, I submit the following description of the survey made by me for the underground tunnel-connection between the Riverside and Home coal-shafts, at Leavenworth, Kansas. The State law requires an escape-shaft; and as neither of the shafts had one, the two companies decided to make this connection in order to comply with the law and still escape the great expense of sinking

Jan 1, 1895

By H. H. Lowry

SCIENCE attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as applied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on dis-coveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the opposite. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accom-plished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 6.1 to 8.3 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in, the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By L. W. Kempf

THE thermal conductivity of aluminum alloys is of considerable indus-trial importance. This is particularly true in such applications as inter-nal-combustion engines where one of the principal reasons for the use of these alloys is their relatively higher thermal conductivity. In spite of this, relatively few data are available on this property of aluminum alloys. The reason is quite apparent to anyone concerned with the experimental determination of coefficients of thermal conductivity. This determina-tion, in theory so simple, is extraordinarily difficult if any high degree of precision is desired. Fortunately, some knowledge of the relationship between thermal and electrical conductivity has permitted the use of the latter physical property in deducing the relative approximate-values of the thermal conductivities of metals. This fundamental relationship, first enunciated by Wiedemann and Franz1 as applying to metallic elements and later shown by Lorenz to be applicable to alloys within a single metallic system, has been of service in the industrial application of metals. The electrical conductivity of metals is easily determined with a high degree of precision. It is, therefore, quite desirable that the relationship between electrical and thermal characteristics be determined with the greatest possible precision. This paper presents data on the electrical and thermal conductivities of a number of aluminum alloys of industrial importance.

Jan 1, 1937

By E. G. Woodruff

(Butte Meeting, August, 1913.) FEW authors of treatises and papers on engineering subjects have . given adequate attention to topographic maps.. The statement applies especially to mining engineering in all branches. Even those who have discussed such maps have treated the subject only in a general way. Therefore it is proposed to outline in this paper a few of the uncommon, yet important relationships which topographic maps and their by-product, structure-contour maps, have to modern methods of mining investigation and development when the facts depicted on such maps are properly interpreted. Topography, as suggested by the etymology of the word, menus a detailed description of particular places. Written descriptions have been found less effective than the pictorial representations, therefore attempts have been made in various ways to picture the surface features of places. Lines and shading have been used, hachures drawn, and, finally, the contour topographic map. To a large extent this style of snap is the result of the demands of engineers. It is designed to meet their needs far more than those of the man untrained in engineering. In fact, the average man obtains a better idea of the topography of an area from the hachure system than from contour maps. . Since the maps. have been made chiefly for the use of the engineer, they ought to meet his demands on the one hand, and, on the other, should be used by him to the fullest extent. Such maps, when properly made, accurately portray a portion of the earth's surface and should present the topography better than a personal examination of the area without a map could present it, because the person making such examination views only a limited portion of the surface at a time, and estimates distances only roughly with his eye. Let the engineer consider carefully the fact that in many instances the topographic map is superior to a personal examination of the surface features of a property because the map is based on careful instrumental measurements, whereas the eye gives imperfect data because it can be used merely for the estimation and

Jan 6, 1913

By J. G. Bartram

Jan 1, 1934

By J. C. McCarthy, J. B. Stone

At Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. Location The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in. the world. Another famous old silver district, Sombre-rete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo On on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is Surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proano hill are the Fresnillo mines, and it is marked now by a great gash cut by glory-hole mining. According to an account written in 1834 by Francisco Garcia, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between zacatecas and sombreretea Little is known of the earliest mining at Fresnillo, which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notably active in 1751 under an administrator named Murguia, who left detailed notes describing them. In I757, however, the mines became inactive because of dificulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor Garcia had been aroused by the long disregarded notes of Murguia. Under Garcia's energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difliculties, including abnormal rains and an epidemic of cholera. In 1835 English capital was sought to allow installation of steam-driven is pumps at the two principal shafts and to build the great hacienda de beneficio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1949

By J. C. McCarthy, J. B. Stone

At Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. Location The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in. the world. Another famous old silver district, Sombre-rete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo On on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo is Surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proano hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proano hill are the Fresnillo mines, and it is marked now by a great gash cut by glory-hole mining. According to an account written in 1834 by Francisco Garcia, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between zacatecas and sombreretea Little is known of the earliest mining at Fresnillo, which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notably active in 1751 under an administrator named Murguia, who left detailed notes describing them. In I757, however, the mines became inactive because of dificulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresnillo became the property of the State of Zacatecas because the interest of Governor Garcia had been aroused by the long disregarded notes of Murguia. Under Garcia's energetic leadership the mines were reopened, and silver production began in 1832 in spite of serious difliculties, including abnormal rains and an epidemic of cholera. In 1835 English capital was sought to allow installation of steam-driven is pumps at the two principal shafts and to build the great hacienda de beneficio (the present Proano hacienda). The company formed in 1835 (Cia. Zacatecano-Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1949

By Howard M. Wells

The investment worth of a mineral deposit can only be realistically evaluated in relation to specified engineering design criteria which fully detail the proposed method of exploitation. The operational design of a mine falls essentially within the technical discipline of the mining engineer, under the constraint that the technical design should be aimed at optimizing the financial attractiveness of the project. In the case of a marginally viable proposition it becomes vitally necessary to identify the best set of design parameters which together will add up to an optimum investment proposal. This paper examines some fundamental logic of optimization for a "wasting asset" type of investment such as a mine, with special reference to the rate of annual production and the strategy of selective mining.

Jan 12, 1978

By G. V. Raymor, James T. Waber, I. Rex Harris

The lattice parameters of a series of fcc alloys of cerium and thorium were measured at 93 " and 298OK. Lattice parameters were also estimated for 171OK. Substantial deviations, y, from Vegard's law were observed. Although y was negative at the two higher temperatures, it was positive and large at the lowest temperature. A variety of models, which have been proposed in the past, were considered, and the calculated values of y were compared with the observed values. The best agreement was achieved with values computed with Friedel's equation. THE purpose of this investigation was to determine the effect of temperature on the lattice parameter and on deviations from Vegard's law of Ce-Th alloys. A large negative deviation from Vegard's law was first observed independently by Weiner, Freeth, and Raynor' and Van vucht2 in the room-temperature lattice parameters of Ce-Th alloys that form a continuous series of solid solutions. This observation was confirmed by Evans and Raynor. The allotropy of unalloyed cerium was reviewed recently by Gschneidner, Elliott, and McDonald. In two subsequent papers,5" these authors reported the influence of various alloying additions on the y= transformation, which occurs below room temperature. Although other rare earths tend to stabilize the double-hexagonal phase, thorium, plutonium, and scandium as solutes tend to stabilize the normal fcc phase. With addition of sufficient thorium as a solute, there is evidence that the formation of is suppressed and it becomes possible to pass continuously with decreasing temperature from the room-temperature phase to the fcc a phase. Thus there is a closed loop which is similar in many ways to the y loop well-known in ferrous alloys. A closed field also occurs in the pressure-temperature "equilibrium" diagram of unalloyed cerium. Because of interest in the effect of thorium additions and their influence on the a and phases, lattice-parameter measurements were made at low temperatures on the fcc phase for a series of alloys ranging from 10 to 90 at. pct Th. The results obtained at three temperatures are shown in Fig. 1. Evans and Raynors analyzed the deviations from Vegard's law in Ce-Th alloys in terms of changes in the occupancy of the 4f electron level in cerium,

Jan 1, 1964

By R. W. Raymond

Franklin Guiterman was born March 7, 1856, in Cincinnati, Ohio, where his father, William Guiterman, was at that time engagcd in the wholesale dry-goods business. Both of his parents were natives of Bavaria, but the inspiration of America was upon them, as they gave to their son a peculiarly American name, symbolizing thrift, individualism and scientific knowledge. Franklin Guiterman received his general education in the grammar schools and the Hughes High School of Cincinnati. He finished the latter course in the early 70's of the last century, when the great demand for mining and metallurgical experts in this country naturally led his parents to direct his further studies in that direction. Accordingly, he went to Europe, and studied at the Royal Saxon Mining Academy of Freiberg, where he completed the course in 1877, at the age of 21, and returned to the United States to engage in mining and metallurgical practice. Going to Colorado, he became assayer for the Terrible mine, at Georgetown, and in 1878, for the Little Chief mine at Leadville. The position of assayer, particularly at that period and in that region, was the door to much valuable knowledge of mines and ores. Besides learning the nature and value of the different classes of ore from the mines of his own company (if he was employed by a company) the assayer, had the first chance, through his outside customers, of seeing and testing the specimens brought by prospectors, and thus learning of important new discoveries. Moreover, if he possessed metallurgical knowledge, he might advance to the position of a metallurgical manager. Guiterman stayed in Leadville four years, and during that period was assayer or chemist for several different companies. Then for about a year he superintended copper-mining operations at Hartville, Wyo. In 1884, he had charge of sampling works at Silverton, colo.—an admirable opportunity for gaining wide knowledge of the varied ores of the San Juan country. In 1885, he was Superintendent of the Mingo plant of the Pennsylvania Lead Co., at Sandy, near Salt Lake City, Utah. The foregoing list of employments, each occupying not more than a year, certainly looks like the history of a rolling stone, gathering no moss. But the cause of these frequent changes was not inefficiency in each new position. In that time and period, a man who lost his place for such a reason was not likely to get another in the same neighborhood might away. And as for gathering "moss," the kind of "moss" that

Jan 1, 1918