Search Documents

By Edgar Stansfield

ONE of the most striking features of the coal series passing from peat through brown coal, lignite, etc., up to anthracite is the gradual reduction of moisture content with the increased coalification of the original plant material. Thus drained peat from a bog may contain 90 per cent water, brown coal contain 50 per cent, lignite 30 per cent, while a bituminous coal may contain only 1 per cent moisture. Moisture, therefore, is one of the important factors to be considered in coal classification, especially with the lower rank coals. With bituminous and higher rank coals the moisture content is less satisfactory for classification; it may even pass a minimum value and then increase with increasing rank to anthracite and superanthracite. Coal in an undisturbed seam contains moisture which is an integral part of the coal, but it may also be wet with free, underground water percolating through the seam. Only the former must be considered in evaluating the moisture content of the coal for classification purposes; this will be called the "true moisture" of the coal. When the seam is mined and sampled the sample taken may show the true moisture; on the contrary, it may contain in addition free mine water or, especially in dry, well ventilated mines, it may contain less than the true moisture. Coal contains unstable organic compounds which may decompose, with the production of moisture, when the coal is exposed to air at ordinary temperatures, or is heated with or without exposure to air. The potential moisture of a coal therefore is higher than its actual moisture. The lower the rank of the coal, the greater its instability, as a rule, and the greater the care necessary to avoid oxidation or decomposition in any investigation of moisture content. The majority of coal workers have preferred, on account of the difficulty in evaluating the true moisture of a coal, and for other reasons, to classify coals by analyses calculated to the dry-coal basis. A number of workers familiar with lower rank coals have recently insisted that the classification of such coals can be satisfactory only if analyses on the moist-coal basis are employed. The moisture-holding capacity of coal is therefore intimately connected with coal classification, and in this paper a procedure is outlined for determining the true moisture of a coal.

Jan 1, 1932

The difficulty of finding new ore bodies, the complexities of patenting them when they are found, and the absence of incentive legislation for exploration have limited mining exploration in the United States mostly to the big companies. This situation, coupled with ECA spending abroad, has caused American capital to look outside our national boundaries for investment opportunities which are further made attractive by some relaxing of restrictions to gain American dollars and patronage.

Jan 1, 1950

By Harry V. Warren

There are two topics which may be considered as opening gambits in any conversation in any part of the world, weather and health. Nothing much can be done about the former, and it would appear that no great changes can be anticipated in the immediate future. With respect to health, a great deal has been achieved in the past 150 years, curiously enough not all of it by medical men. It would appear that the time is now appropriate for geologists to come to the assistance of medical men. During the past few decades, medical science has mastered many of the diseases commonly associated with childhood. As a man tends to live longer, those diseases usually associated with middle and old age become more prominent. Thus we must realize when we say that today more people are dying of cancer and coronary disease, absolutely and relatively to other diseases, this should not suggest that these diseases did not exist a hundred years ago; it does suggest that more people are living to an age where death from these diseases is apt to become more common.

Jan 7, 1962

By Marc Lemieux

Computer pit design techniques generally make use of models in which the deposit is represented by a regular array of data. Using a regular system, the number of data points required to represent the air, waste and mineralization in a large deposit become excessive. The number of blocks used to describe the deposit is dependent upon the block size. The quality of the pit wall slope design also is dependent upon the block size used and the method of defining the slope. The error associated with reserve calculations becomes greater with increasing block size. A deposit model consisting of variable sized air and mineralized blocks has been developed at the University of British Columbia and improved upon at Climax for pit design work. The method permits put- ting the entire model in core for rapid data processing. This permits the use of a versatile cone generation technique which allows close adherence to variable slope constraints in all directions. The conical shape is approximated by rectangles on each level which equal the area of the ideal conical intersection. The shape of the intersection may vary from approximately circular to elipsoidal. The approximate cone shape is controlled by the slope constraints applicable at the point of intersection on the bench. The overall modeling technique greatly assists the pit design engineer in developing a high quality pit design.

Jan 1, 1977

By D. R. Hanson

The acoustic vibrational spectra of impacted rock slabs were examined at the Denver Research Center, US Bureau of Mines, in an attempt to characterize the behavior of partially detached mine roof rocks. The ultimate goal of this study was to develop a technique or instrument that could provide a quick, accurate, quantifiable measure of mine roof stability. The power spectra of unstable rock slabs were found to contain more energy in the range of 200 to 1000 Hz than solid rock. Comparison of the power contained between 500 and 1000 Hz with that between 3000 and 3500 Hz provided a quantitative measure of rock stability. A lightweight prototype field instrument was designed, constructed, and field tested. This battery-powered instrument computes the power contained in the two frequency bands, compares their magnitude, and displays a number related to the stability of the block tested. Field tests showed the instrument provided reliable measurements of block stability even under conditions of noise that would have seriously degraded the accuracy of the standard methods of roof sounding.

Jan 1, 1986

By D. Hodouin, T. Gelpe

A digital simulator of classification and grinding circuits is used to evaluate the performance of various flowsheets. For a given flows he et configuration, unit process dimensions, and operating conditions, the simulator calculates the steady-state values of the process variables and determines the conditions that meet the required operation criteria for tonnage and product quality. Calculation examples are proposed for the design of wet and dry grinding circuits. The performance of different configurations of cement clinker and sulfide ore grinding flowsheets is evaluated and discussed.

Jan 1, 1986

By A. G. Lyle, J. D. Runkle, G. A. Gillies

THE evaluation of data obtained by selective flotation from even a simple ore is a very difficult process, and when the ore tested is complex the process becomes extremely difficult and cumbersome. The authors, in the course of an investigation into the selective behavior of various flotation reagents on nonmetallic minerals§ were confronted with an aggravated form of this difficulty, owing to the large mass of data that had accumulated over a period of years. They finally devised a method whereby the results of the various flotation tests could be correlated and interpreted by means of graphs representing recoveries and rejections of the component minerals in the ore. This method of graphical analysis proved so useful in nonmetallic flotation that it was afterwards applied to sulphide flotation, where it yielded equally satisfactory results. Since this method of analysis leads to very definite conclusions as to the effect of changes in reagents and flotation procedure, it is felt that a wider application of the method might assist the industry by reducing the amount of test work required, and possibly increase the accuracy of the final analysis. GRAPHS In Fig. I, four curves are plotted on the same graph with cumulative percentages as ordinates and cumulative weights as abscissas. In this instance the four curves are named, respectively: the barite-recovery curve, the limestone-rejection curve, the silica-rejection curve, and the summation curve. In these tests barite was the mineral concentrated, therefore a barite concentrate was produced. Definitions Before explaining the curves in detail it might be advisable to define several new terms, such as "percentage rejection," "summation index," and "summation curve," as well as the word "test," which has been used in a special sense. A "test" will include all the operations performed upon a batch of ore from the time it is placed in the rod mill until the last product has been assayed. Thus a test may be a comparatively simple procedure producing only one concentrate and a tailing, or it may be a very complicated procedure producing five or more concentrates of a specific mineral as well as a tailing. The number of concentrates produced will depend entirely upon whether the collector was added to the pulp in the flotation cell in one lot or was added in five or more portions. Percentage Rejection.-The ability of a selective flotation collector to reject an undesired mineral is just as important as its ability to collect the desired mineral. The percentage rejection curves shown on the graphs give this factor due consideration and its value is calculated as follows: Suppose a concentrate contains 5 per cent of an undesired mineral. This indicates

Jan 1, 1942

BOSTON SECTION R. L. AGASSIZ, Chairman, - JAMES G. CARLETON, Vice-Chairman, E. E. BUGBEE, Sec.-Treas., Mass. Inst. of Technology, Cambridge, Mass. W. E. C. EUSTIS, G. A. PACKARD. The forty-fifth meeting of the Boston Section was held, at the Engineers' Club, on Tuesday, Nov. 6, 1917. Mr. F. C. Carstarphen, tramway engineer of the American Steel and Wire Co., was the guest of the evening. After dinner, Mr. Carstarphen gave a most interesting illustrated talk on the subject of aerial tramways. The views-showed the various forms of aerial tramways and three' unique installations, one carrying 285 tons of coal an hour, undoubtedly the maximum quantity transported by any tramway up to this time. The second installation is that of a lumber-carrying tramway, 5 miles long, operating in California. The last views illustrated a 13 ½ -mile tramway for carrying salt over the

Jan 2, 1918

By Uros Bajzelj

To mine very weak carboniferous schists subjected to high ground pressures the underhand cut-and-fill stoping method was proposed using an artificial plate roof. An experimental stope was mined using three consecutive levels. Rock pressures, deformation of the reinforced concrete plate, and the quality of stowing were evaluated. It was found that roof deformations were minimized if the reinforced concrete plate and uncemented backfill were replaced with cemented backfill containing reinforcement near the bottom. The mining method prevented the occurrence of high rock pressures at the face. The method is suitable for mining subvertical ore bodies with large horizontal areas.

Jan 1, 1984

By B. H. Caudle, B. M. Hickman, I. H. Silberberg

Secondary recovery projects often are not started in oil reservoirs until dictated by rising GOR's or declining oil production. Such circumstances require a well dispersed injection pattern to prevent the oil bank from bypassing the production wells. Many times this purpose is served by using the five-spot or line-drive patterns, in which half of the wells are made injection wells. A regular injection pattern is proposed that is based on the same well spacing as the five-spot but in which only a third of the wells need be converted to injection wells. Fluid flow model studies on this proposed pattern show that production histories will be as good as those for a five-spot pattern at mobility ratios of three and above. The model data are presented in a form that may be used to predict recoveries from both homogeneous and stratified formations. Introduction The injection of fluid into a petroleum reservoir usually is prompted by an actual, or predicted, loss in the productivity of the reservoir. Often, an oil reservoir is produced by pressure depletion until high GOR's dictate a change in policy. Fluid injection also causes increased ultimate recovery, but this usually is of less importance to the operator than is the maintenance of the production rate. It is a fact that the ultimate recovery in any particular fluid injection project is relatively independent of the number and spacing of the injection wells as long as the reservoir voidage through the production wells is balanced by the total injection rate. However, the response of a production well is directly affected by the distance it lies from an injection well. In places where the well productivities are declining, the injection wells should be spaced as evenly as possible among the producing wells ("dispersed" injection pattern). More particularly, if the production response depends upon the formation (and subsequent production) of an oil bank, each production well should be surrounded by injection wells. Otherwise, the oil productivity will increase very little as the oil bank moves past the well.'.' An evenly spaced injection pattern has the best chance of generating an oil kick in the production wells. If reservoir voidage and injection rates are to be equal, the ratio of injection wells to production wells must be equal to the ratio of the average injectivity to the average productivity (in reservoir volumes). This ratio is in strumental in choosing the injection pattern. Table 1 shows the production well to injection well ratio for the dispersed injection patterns that have been described in the literature.'-' All of these patterns will have comparable recoveries and response times (for the same basic distance between wells). The choice of pattern there fore depends upon the relative injectivity and productivity of the wells and upon the type of drilling pattern employed. Another important factor may be the ability of the proposed production wells to make up the lost productivity from those wells converted to injectors. These factors become more pronounced at the higher oil viscosities (low gravity oils). All other things being equal, the probable ratio of single well injectivity to single well productivity will be equal to the water-oil mobility ratio of the proposed flood. Thus, high mobility ratios (due to low gravity oil) should call for fewer injection wells — as long as these injection wells are "dispersed" to obtain more even pro duction response for the remaining wells. Secondary re covery projects in oil reservoirs seldom, if ever, will have mobility ratios requiring more injection wells than production wells. Thus, only the last five of the patterns listed in Table 1 will be of significant interest in oil recovery. Almost every development drilling program calls for the wells to be drilled along equally spaced rows and

Jan 1, 1969

By C. Edward Capes

Fine particles in liquid suspension can be agglomerated by a number of mechanisms. Well-known methods include the addition of electrolyte to reduce the zeta potential and allow mutual adhesion arid the use of polymeric flocculants to bridge between the particles. A more recent technique, "spherical Agglomeration", is the subject of this paper. The process involves the addition of a second liquid which is immiscible with the suspending liquid and preferentially wets the particles to cause particle adhesion by capillary liquid bridges. Progress in the application of spherical agglomeration to a number of distinct technological fields is reviewed in this paper. The areas of interest include the formation of dense, highly spherical agglomerates, the separation of solids from suspension and the fractionation of complex, multi-component solids mixtures, such as ores. Some of the more interesting recent applications in the energy and environmental fields, such as the beneficiation of' coal and tar sands, are highlighted.

Jan 1, 1977

By Charles Meyer

The year 1955 was a busy one for mining geologists, for the expanding world-wide business activity kept the demand for mining products generally high, stimulating operators to develop local ore reserves and to expand their efforts to find new deposits. The uranium rush was still on, although probably past its maximum rate of climb. Prospecting was also stimulated by the increasing demand for rare metals, and this created new and fascinating targets for exploration. On the whole, it was a boom year when the prospector's chronic optimism found few repressions.

Feb 1, 1956

By W. M. Bertholf

In 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral call make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory)" as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,' but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1947

By W. M. Bertholf

In 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral call make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory)" as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,' but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1947

By K. J. Brondyke, P. D. Hess

Lack of correlation between densities of aluminum alloy samples solidified under reduced pressure (vacuum gas test) and hydrogen content of the metal is explained on the basis of inclusions serving as nuclei for hydrogen bubble formation. As a result of these findings, the vacuum gas test is suggested as a practical tool to indicate metal cleanliness and the potential effects of hydrogen. Visual obseroation of the sample during solidification under vacuum provides more useful information than that obtained either from density meas -urements or sectioning of the solidified sample. A rapid, practical method of detecting and measuring gas in molten-aluminum alloys has been sought for many years. The development of the vacuum gas test appeared to solve this problem. However, the vacuum gas test is subject to certain limitations, and the results must be interpreted mindful of these limitations, as described herein. Since the only gas which is appreciably soluble in aluminum is hydrogen, the terms gas and hydrogen will be used interchangeably in this paper. In the early days of the aluminum industry, when techniques were not as refined as they are today, it was customary to pour small "pancakes" of alumi- num on a metal plate. These were allowed to solidify under atmospheric pressure. Excessive gas in the metal was evidenced by the appearance of small bubbles on the surface of the "pancake".' It is obvious that such a method would only show very high gas levels far above any which could be tolerated by today's standards of quality required for most applications. Various attempts were made to develop methods which would be more sensitive. Among these were measurements of density of aluminum alloys solidified under controlled conditions, radiography of cast slabs, and examination of fractures. The method which showed the greatest promise and appeared most practical was the solidification of a sample of the molten aluminum alloy under vacuum. The samples so solidified are evaluated either by observation for bubble emission during solidification, by sectioning the solidified sample and examining for porosity, or by determining the density of the solidified sample. This test is known internationally as the Straube-Pfeiffer test or the reduced-pressure solidification test, but in America it is commonly referred to as the vacuum gas test2-' and will be so designated in this paper. The determination of density appeared an attractive and convenient means of providing a numerical rating for the samples. Attempts were made in some instances to correlate densities to hydrogen contents. Unfortunately, the visible loss of gas during solidification of samples with high gas contents precluded a correlation of vacuum gas test densities with the observed gas evolution. This led to Alcoa's use of two different pressures; 50 mm of

Jan 1, 1964

By E. C. Bitzer

The primary object of the work described in the following pages was to simplify the equipment in the separating circuit of the heavy-media process by substituting a spiral classifier for the separatory cone. Mechanical considerations were the leading attraction and the best that was hoped for on metallurgical performance was that the new vessel would give results equal to those obtained by conventional equipment. Tests have demonstrated in commercial operation on iron ore that the mechanical advantages of the spiral separator are about as predicted; also, the metallurgical performance is superior to the cone on the ores treated. Treatment of iron ore involves the separation of two products: a concentrate that sinks and a float product that contains true float material plus a controlled division of interfering middling. The middling material is heavier than the average specific gravity of the separating medium. Recent work with the spiral separator on Tri-State zinc ore showed that the middling material had to be recovered as concentrate because this fraction contained the bulk of the zinc in the ore. It has been demonstrated that it is possible to make three products with the new separator on an ore such as this: a float tailing, a float middling, and a high- grade heavy sink product. It appears from this last work that the new separator has definite mechanical and metalluigical advantages over any type of separating cone for treating feed that contains large amounts of material of a specific gravity close to that of the separating medium. However, either type of separator should perform equally well, metallurgically, on feed that is free of middlings. Each series of experiments with the spiral separator has required additional work to fully develop the possibilities of the machine. For this reason the paper is divided into chronological parts. History of Development A drag-type classifier was first proposed as a substitute for the cone separator by Butler Brothers technicians during the initial tests with galena medium at Crosby, Minn., in 1937. The desire for finding a substitute for the cone arose from trouble with interfering middlings and certain operating disadvantages of the cone. The possibility of using a spiral classifier was also suggested at this time by Emmett Butler and C. J. Abrams. However, inability to satisfactorily recover fine galena, which was used as a medium, terminated all development work at Crosby. During the winter of 1937--1938 investigation started on magnetic medium with concurrent development of the inverted or closed-top cone, which was found necessary to eliminate iron-ore middlings with the float product. About

Jan 1, 1949

By E. W. Shaw

Continued discussion of the paper of Roswell H. JOHNSON, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 221 to 226. See also Bulletin No. 101, May, 1915, pp. 1157 to 1162. E. W. SHAW, Washington, D. C. (communication to the Secretary+). -With the word petrology-literally the science of rocks-being used primarily for igneous rocks, and with geophysics coming to mean the study of lavas and the rocks into which they solidify, contributions to the knowledge of the physical chemistry of sedimentary rocks, even though only ideas which may be used as working hypotheses, become most welcome. The forces which control the formation and subsequent history of the stratified portions of the earth's crust are so little known that no one has yet been able to settle finally the questions as to whether petroleum is of organic or inorganic origin; whether it originated far from its present position, or nearby. Yet both the chemical and physical problems of the rocks in which oil occurs seem to be more simple than those of the igneous rocks. The oil-bearing rocks of western Pennsylvania, for example, have in all probability never been subjected to a pressure exceeding 3,000 or 4,000 lb. to the square inch, nor to a temperature higher than 100° or 200° C. These pressures are considerably below the crushing strength of rocks, and the temperature far below their melting point. The igneous rocks,, on the other hand, have been affected by enormous pressures and very high temperatures and yet steady progress is being made in reproducing in the laboratory the conditions of their formation and subsequent modification within the earth. The solution of the sedimentary-rock problems would seem to be fully as important as those of igneous rocks, and yet we must content ourselves with reasoning backward and our inferences as to what has happened are oftentimes little more than guesses.1 One of the fundamental problems is the origin of the salt water in oil fields. Is the salt water fossil sea water; has it been formed by the solution o-f salts of various kinds from distinct beds, from disseminated par-ticles, and from the weathering of suitable grains in the rock; or is it of deep-seated origin? Its general resemblance to sea water points to the first, but the principles held by some concerning the free circulation of water throughout the earth's crust, and certain peculiarities of composition indicated by the few analyses available, seem out of harmony with such an explanation.

Jan 7, 1915

By S. K. Ruggieri, R. A. Jankowski

Airborne respirable dust levels on longwalls can be reduced if operators approach the dust control problem in a logical and fundamental manner. This can be accomplished through the proper application and continued use of effective dust control techniques. The Bureau of Mines is currently assessing the effectiveness of longwall dust control techniques in use today to provide mine operators with guidelines for selecting the most appropriate control technology. This paper presents a fundamental approach to the problem of shearer dust control. Three dust control techniques to be discussed are: deep cutting/increased pick penetration for reducing the amount of respirable dust generated; drum water sprays/improved water supply system to suppress the amount of airborne respirable dust; and improved external water spray system, the “shearer-clearer, "to push the dust close to the face. The techniques have been evaluated infield trials and have been shown to be both practical and effective in applications to control shearer generated dust.

Jan 1, 1985

By H. R. Hanley

IT is a well-known fact that the solubility of zinc compounds decreases when these compounds are roasted in contact with iron compounds, but descriptions of tests to quantitatively express the fact have not appeared in the literature. Possibly such an expression cannot be uniformly and exactly duplicated by different operators because of the variation in the personal equation. In a general way, however, the reactions between zinc compounds and iron compounds under roasting conditions will show a certain trend with changing conditions and the approximate quantitative expression of this trend appears reasonably well established by experimental work conducted for this purpose.

Jan 1, 1929

By Michael Tenenbaum

RECENT researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any sub-stantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed.

Jan 1, 1939