Search Documents

By Bernard Greifer, Walter Rose

The purpose of this note is to call attention to a source of difficulty which can be responsible for inaccurate estimates of wetting liquid pressure gradients in mixture flow experiments of the Hassler1 type. It has been our experience occasionally to observe what were indicated to be negative pressure gradients, and these were regarded as anomalous in the sense that physically they seemed to contradict the requirement that the flux be in the direction of the potential field. At first it was thought that our scheme of assembling barriers and core sample led to such asymmetry in the distribution of isobars that the manometric leads at each end of the core were responding to internal pressures (within the core sample) which could be either positive or negative with respect to each other, and which in fact might tend to reflect on different effective core lengths in an unpredictable fashion as the wetting liquid saturation was changed. However, no compelling evidence of this possibility has been established. In addition, we were cognizant of the requirements to be satisfied in selecting manometric instrumentation to minimize the delay in response of the manometer to the differential pressures being measured, and were thus assured that our observations of anomalous pressure gradients could not be explained by faulty instrumentation. What we suggest is that if a leak sink occurs in the fluid lines connecting the core to either side of the differential manometer, errors exceeding 100 per cent may result in the estimation of wetting liquid pressure gradient, even though the leak is of such small magnitude that its existence would tend to be obscured by evaporation effects. This is because in a system with leaks at the specified places, the manometer rec- ords at steady state the pressure drop across the manometer barrier elements in addition to the pressure drop across the core sample. This possibility will be illustrated below analytically and by numerical example for the special case where the leak occurs on the high presure side of the core, since we are especially desirous to explain the significance of our observations of the so-called negative pressure gradients. It will be indicated, however, that leak sinks on the low pressure side of the core can account for observations of anomalously high values of pressure gradient, and that multiple leaks on both sides of the core can provide for some compensation so that the errors in pressure estimation are reduced. However, the major point to be emphasized is the fact that the impractical-ity of detecting the small leak sinks which give rise to the difficulties makes it a complicated task for the experimenter in a particular case to know with certainty that his estimation of pressure gradient lies within the limits of error which can be tolerated. Fig. 1 shows the electrical analog of the flow system we have employed in our studies. The inflow and outflow barriers. Rbl and Rb2, the manometer barriers, Rm1, and Rm2, and the core sample, Rc— for a particular fluid saturation and distribution— are all designated as resistance elements; the flowmeter is designated by an ammeter, A; the pressure source is designated by E; and the manometric device is designated by the voltmeter, V. Included in the circuit are the variable resistances, Rx and Ry, which may be regarded as the leak sinks, and which, in general, can vary in magnitude from zero (i.e., a large hole or shunt in the system) to infinity (i.e., no

Jan 1, 1950

By S. Ito, Y. Watanabe

In the long range production planning at the Matsumine mine, a management target is to maintain a desired production rate and to keep fluctuations in copper and zinc grades within given allowable limits. A simulation model was developed to find, on a trial and error basis, how feasible and practical the target may be under certain constraints on the underground mining sequence. A number of simulation runs have been made to obtain the most suitable production rate for the long term. In this paper, an outline of the simulation model is described.

Jan 1, 1976

By Hobart M. Kraner

THE mineralogy of blast furnace sinter is of interest because its mineral content is one of the important factors contributing to its character. There are so many other factors affecting the properties of the sinter, however, that it is well to mention them here. The proportion and character of the raw materials, that is, raw ores, concentrates, returns, and fuel, as well as the mixing and the water content, all have a marked effect on the physical properties of the product and the degree to which sintering action can be carried on. The process of sintering is a relatively fast operation. In as much as appreciable time is required to carry on processes of fusion in such masses of low thermal conductivity, large lumps of hematite ore frequently remain unfused and partly unchanged in state of oxidation in the sintering process. The kind, the grain size, and the amount of fuel used affect both the completeness of the fluxing reaction and the prevailing atmosphere. The rate of reduction in laboratory tests is not only dependent upon the state of oxidation of the sinter but also upon the sizing and porosity. Atmosphere and temperature affect the state of oxidation of the iron oxide, and the atmosphere alone may determine the ferrous minerals that finally develop. The rate and extent of cooling, the type of coolant, the subsequent handling, and screening all have serious effects upon the type of sinter that eventually enters blast furnace bins. The degree to which actual fusion or fluxing takes place in the sintering operation has a marked effect upon density. A sinter which has been extensively fused by high content of fuel in the batch will no doubt have a higher weight on the bulk basis than one which had a lower fuel content. As high temperatures are required to do this job, the iron oxide under these conditions will be largely magnetite. Sintering at low temperatures to produce larger proportions of hematite means a decrease in the amount of liquid formed and a much more sensitive bonding process. In this case the liquid must be distributed more uniformly and thereby used more efficiently than would be the case where higher temperatures were permitted to prevail more or less indiscriminately. Where coarse ore particles are used in a sinter mix it is not expected that any particles coarser than 1/4-in. can be fused and incorporated in the system to such an extent that the gangue contained within these lumps will have been converted or fused by the sintering process. It is for this reason that coarse ore, returns, or both, in a sinter usually result in a sinter which breaks easily and at the same time may contain some of the original minerals of the lump, such as quartz and hematite. In examination of sinters at Bethlehem Steel Co. minerals such as quartz and corundum have been found, none of which are considered normal associ- ates of wustite or magnetite. Some degree of heterogeneity or lack of equilibrium is not unusual in the sintering process. The differences in specific gravity between hematite and magnetite might be ample reason for poor strength in a not very well sintered mass containing coarse particles of. ore or returns. The shrinkage taking place in a lump of hematite in its conversion to magnetite by temperature and/or atmosphere is appreciable. Sintering of ores as it is carried out is crude chemistry, for the grain size is relatively coarse, the application of heat is certainly not uniform, and the time factor is inadequate for other than partial completion of reactions. Coarse lumps of coke or coal cause local heating around these centers, and fuel which is too fine may result in such slow burning that sufficiently high temperatures are not always obtained. High temperatures are essential to the work required. The Swedish practice of sintering is established on the basis of producing an easily reducible product high in hematite. This is achieved through uniformity of grain size in the sinter mix and close control of the temperature through careful regulation of fuel and sintering rates. This produces a sinter which is very tough in character and which has a high degree of porosity. Although the hematite content is not produced upon cooling by drawing air through the mass, there would be greater possibility of accomplishing this reaction with this type of sinter than is the case in American practice. In the latter, the temperatures are so high that temperature alone converts most of the mass to magnetite. The grains are so coarse in the final product that together with the fluxed condition it would be difficult to reoxidize them to hematite upon cooling. An examination of the iron-oxygen diagram' shows that hematite does not exist above 2651°F. It also shows that there is no liquid in the pure magnetite-hematite system until 2881°F is reached. On the other hand, in the system magnetite-wustite liquids exist at considerably lower temperatures than this. It will be seen, therefore, considering only the iron oxides, that the bonding action obtained in America in sinters comes about through considerable temperature and/or reducing conditions that produce compositions containing even less oxygen than is contained in magnetite or than results from the fusion of silicates. The bonding obtained from the iron oxides is encouraged by the reducing conditions that prevail in the vicinity of the fuel particles in a mass of this sort, where temperatures are above 2600°F. As magnetite and wustite are opaque, they do not lend themselves to petrographic study by transmitted polarized light. The silicates found in sinter and the glass that has not crystallized transmit light and can be studied by these methods in which indices of refraction and other optical properties of anisotropic crystals lead to their definite identification. The index of refraction is the only property that can be measured in glass under the microscope, and this is a clue to its probable approximate composition.

Jan 1, 1954

By John H. Hollomon

IN a recent paper,1 a very early suggestion by Ludwik2 concerning the nature of the mechanical behavior of metals has been reexamined and extended. In essence it was [ ] suggested that there exists, at least under certain conditions, a mechanical equation of state; that the stress required for flow depends upon the instantaneous values of the strain, strain rate, and temperature, and not upon their past values. It is proposed that under these circumstances the stress does not depend upon past history of these variables, but is like the temperature of a gas that depends only upon the I instantaneous values of the pressure and volume. This notion has not been applied to present day studies of metals, though it is especially applicable to the study of creep. It is the purpose of this paper to analyze the significance and possible range [ ] of applicability of this idea and to deter- mine how it influences the accepted ideas concerning creep. STRESS-STRAIN RELATIONS It is well known that the stress-strain curves of metals are influenced by both strain rate and temperature. For a fixed strain rate and temperature there is associated with each metal a stress-strain curve. If either the strain rate or temperature is changed a new stress-strain curve will be characteristic (Fig. I). A much more general relation between the effects of the sevariables is possible, however. Consider the stress-strain curves of Fig. I determined at

Jan 1, 1946

By H. Shaw

IT is now generally recognized that the gravitational method of geophysical surveying is a valuable aid in elucidating the geological structure of the subsoil and enables the practical geologist to deduce the presence of useful deposits. The particular suitability of the torsion balance to the location of large and important subterranean structures has given rise to a wide application of this method by many of the important oil companies in their search for future supplies, and so intense have been these efforts that little has been heard of the method in other connections, with the exception of occasional references to its application in the location of hidden deposits of metallic ores, salt and lignite, and a number of accounts of its use in the elucidation of geological structures. Its success in the location of salt domes is well known, and establishes it as one of the most important of the geophysical methods, especially for the indirect location of oil. In the British Isles, however, no large occurrence of oil is likely to be revealed, and here the practical application of the gravitational method has been restricted almost entirely to the search for ores. This type of survey possesses well marked characteristics, and presents a gravitational problem that has necessitated the development of a special and probably unusual plan of campaign, full details of which it is hoped will shortly be published. The problems and difficulties encountered in this work are of necessity fundamentally related to those met with in the search for oil by means of the torsion balance, but they also possess several special and distinctive features which undoubtedly differentiate them from the obstacles confronting the oil prospector, and which call for special consideration and treatment.

Jan 1, 1928

By G. G. Sarkar

SHARPNESS of separation and washing efficiency are often confused. The sharpness index indicates the precision of a washing unit; the washing efficiency takes into account not only the unit's precision but also the washability characteristics of raw coal and the near-gravity materials at the effective density of cut. A sound basis for evaluating the sharpness index is essential in comparing the sharpness of separation attained by different cleaning units. Sharpness Index and Related Criteria: Washing plant sharpness of separation has been well represented by Hancock's efficiency chart and Tromp's curve of migrated materials. Some useful coefficients derived from Tromp's curve-the error area, probable error, and imperfection value-have been widely used to measure sharpness of separation. These are defined in a number of papers presented at the first and second International Coal Preparation Conference held in Paris (1950) and Essen (1954).1-5 In evaluating the performance of a dense medium separator at four different gravities, Yancey and Greer6 observed that even with similar operating conditions and the same size grading of feed, the imperfection value of a washing plant varies through a greater range than the probable error. The present writer also observed the same type of anomalies in comparing the imperfection values of one plant which were determined under almost identical conditions. He therefore devised a graphical method to evaluate a washing unit's sharpness of separation and define it by a single coefficient, which is substantially independent of coal characteristics under normal operation of the unit. Unlike imperfection value, the new coefficient can be expressed on a percentage basis.

Jan 12, 1957

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By V. C. Perini

The 1943 designation of districts for the Transactions† has caused some confusion because of the elimination of the West Central Texas district and the allocation of the counties of this district to the North Texas district and the North Central Texas district. The North Central Texas district as herein defined includes the counties of Brown, Callahan, Cole-man, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, San Saba, Shackelford, Stephens, Stonewall, Summerville, Taylor, Throckmorton and Wise. These counties as listed are the counties of District 7B, State Railroad Commission. This district covers the south central crest and the west flank of the Bend flexure north of the Llano uplift. The west flank of the Bend flexure is on the east boundary of the Permian Basin of West Texas. The North Texas district, District No. 9, State Railroad Commission, includes the counties of Archer, Clay, Cooke, Foard, Hardeman, Jack, Knox, Montague, Wichita, Wilbarger and Young. The area of this district covers the crest and south flank of the Red River uplift and the north central crest of the Bend flexure. The greater part of the oil and gas produced in the past from the North Central Texas district has been from Pennsyl-vanian strata. Some oil and gas has been produced from the lower Permian (by the latest selection of the Pennsylvanian-Permian boundary') and minor amounts from the Mississippian and Ordovician sediments. Increasingly important quantities of oil and gas are to be expected from the older sediments by deeper development in proven fields and by new discoveries. Most of the oil and gas in the district has accumulated in localized, well-defined structural traps in limestone and sandstone reservoirs and in traps due to stratigraphic changes in sedimentation, mainly porosity traps in limestone and sandstone lenses, both usually associated with some structural feature. The Stripper Well Premium Plan as adopted by the office of the Federal Price Administrator has been an aid to the producers of stripper wells. The producers are pleased to receive the subsidy to prolong the plugging of wells, but they are not too pleased with the subsidy plan in principle. Most independent operators are in favor of, and think they are entitled to, an increase in the market price for oil. The price is not adequate to meet the requirements of the average independent operator with the continued advance in production, development and wildcatting costs. Old and new pipe lines for oil and gas leading out of the state are removing reserves at an alarming rate. Curves showing the rate of discovery versus production and pipe-line deliveries in and out of the state make a cross that sooner or later will be fatal to the state. Wildcatting not only needs a price increase but every other available incentive and encouragement.

Jan 1, 1945

Jan 1, 1970

By C. H. Bushell, M. Malnarich

REAGENT control in flotation is more an art than a science. Operators vary the amount of reagents used according to the metallurgy obtained. The amount of collector may be increased, for example, if tailings losses are high and decreased if concentrate grades are low. Often control decisions are based on only one assay, such as the tailings analysis by microscopic or quick assaying techniques. This method of control has given reasonably satisfactory results but is clearly far from perfect. No adjustment in reagent addition can be made until information is received that metallurgy has deteriorated, that is, until the optimum time for adjustment has already passed. The first adjustment probably will be an overcorrection or an undercor-rection, and time will be required to establish the best new addition rates. The seriousness of the problem depends on variability of the ore. In ore of continually shifting composition and complexity, mill results will shift back and forth from excessively high concentrate grades and high tailings losses to excessively low concentrate grades and low tailings losses. Economic incentive for improved control also increases with increasing size of mill. Even a small improvement in percentage recovery in a large mill pays for expensive control equipment. The Sullivan concentrator of The Consolidated Mining & Smelting Co. of Canada Ltd. at Kimberley, B. C., treats 11,000 tpd of complex lead-zinc ore, a scale of operations which justifies an extensive research program on automatic control. Work has followed two separate lines: 1) development of faster analytical methods for pulps, and 2) study of metallurgical control by measurement and control of reagent concentrations in flotation solutions. Although work is incomplete in both phases, a progress report can be given on the development of reagent control. The primary requirement in flotation is selective attachment of particles of one mineral to air bubbles while the other minerals remain detached. Hydrophobicity of mineral surfaces is established by the collector, which coats the minerals by adsorption. The requirement of selective affinity for air bubbles is therefore equivalent to requiring selective adsorption of a collector. Adsorption theory, supported by abundant experimental evidence, shows that the amount of a reagent adsorbed at a surface must be a function of its residual concentration in solution. As the concentration in solution rises, the amount adsorbed increases, usually following some type of logarithmic curve. Selective adsorption must depend on a natural difference in the minerals, but ordinarily the differences in affinity are not great enough to obtain complete coverage of one mineral while the others are completely uncoated. An optimum concentration will exist, below which coverage will not be great enough to float enough of the valuable mineral, and above which too much unwanted mineral will float. All other reagents, except some frothers, affect the amount of collector adsorbing at constant residual collector concentration in solution, either by adsorbing competitively with the collector, or by a

Jan 1, 1957

Jan 1, 1894

By M. R. Geer

THE importance of the size composition of coal is reflected in the differ-ence in price of the various sizes of the same coal and in the large number of primary sizes and mixtures of sizes produced by the modern preparation plant to meet the demands of a market that in late years has grown increasingly conscious of coal size. The importance of size in the indus-trial and domestic uses of coal has its counterpart in the role played by size composition in the laboratory examination of coal. Investigation of many of the physical properties of coal in their relation to its uses requires an evaluation of size composition. In fact, the Standards on Coal and Coke issued by the American Society for Testing Materials in 1936 contains 12 standard methods of testing that involve some use of size composition. The screen analysis is, of course, the standard method of determining size composition, whether the material is coarse run-of-mine coal or fine pulverized fuel. Customarily, the analysis is reported as the weight percentages retained on or passing each of a series of testing screens, the number of which may range from only two or three to as many as 20. When more than two or three sieves are used, which is usual, the number of weight percentages obtained is so great as to make the analysis difficult to comprehend. Direct comparison of analyses made on the same sieves is hard, and comparison of analyses covering the same range of sizes but made oil different sieves is next to impossible. Consequently, a frequent purpose of sizing tests-correlation of size with properties and charac-teristics related to size-is rendered difficult.

Jan 1, 1938

By M. Gensamer

In applied mechanics and in metallurgy the transition from elastic to inelastic action is a matter of considerable interest and importance. Often the first inelastic deformation is apparently quite homogeneous; that is, uniformly distributed throughout the specimen. Sometimes this deformation is heterogeneous; that is, localized; inelastic deformation proceeds to some definite amount in restricted regions before adjacent regions of the specimen are inelastically deformed. In such cases the deformation does not become homogeneous until the whole specimen has been deformed the amount corresponding to that for each localized deformation. If the test is stopped before uniform extension sets in, the heterogeneous character of the deformation is apparent on the surface of the specimen through characteristic markings, which have been called "LÜders'" lines, "Hartmann's" lines, the "Piobert effect," or simply "flow figures." These markings are the source of considerable trouble in fabricating operations, particularly in the deep drawing of steel sheet. In many cases where the transition is of this nature, the stress developed at the upper limit of the elastic range is greater than the stress during the period of heterogeneous deformation, giving rise to the familiar "drop of the beam" effect in testing. The amount of the yield-point elongation, as well as the value of the stress at the lower yield point (the value to which the stress drops when yielding begins), are functions of the temperature and the testing speed. Lower temperatures and faster rates of testing increase both the yield-point elongation and the yield-point stress. These matters have been ably discussed in a recent paper by Winlock and Leiterl though, as brought out by the discussion of that paper, the phenomena are but little understood. The purpose of the present paper is to clarify the problem through the application of a simple principle, and to show that, through the application of this principle, a number of phenomena in the plastic deformation of metals become more readily understood. The principle is this: During homogeneous flow, the rate of work-hardening is greater than the rate of change of stress resulting from change

Jan 1, 1938

By M. Gensamer

In applied mechanics and in metallurgy the transition from elastic to inelastic action is a matter of considerable interest and importance. Often the first inelastic deformation is apparently quite homogeneous; that is, uniformly distributed throughout the specimen. Sometimes this deformation is heterogeneous; that is, localized; inelastic deformation proceeds to some definite amount in restricted regions before adjacent regions of the specimen are inelastically deformed. In such cases the deformation does not become homogeneous until the whole specimen has been deformed the amount corresponding to that for each localized deformation. If the test is stopped before uniform extension sets in, the heterogeneous character of the deformation is apparent on the surface of the specimen through characteristic markings, which have been called "LÜders'" lines, "Hartmann's" lines, the "Piobert effect," or simply "flow figures." These markings are the source of considerable trouble in fabricating operations, particularly in the deep drawing of steel sheet. In many cases where the transition is of this nature, the stress developed at the upper limit of the elastic range is greater than the stress during the period of heterogeneous deformation, giving rise to the familiar "drop of the beam" effect in testing. The amount of the yield-point elongation, as well as the value of the stress at the lower yield point (the value to which the stress drops when yielding begins), are functions of the temperature and the testing speed. Lower temperatures and faster rates of testing increase both the yield-point elongation and the yield-point stress. These matters have been ably discussed in a recent paper by Winlock and Leiterl though, as brought out by the discussion of that paper, the phenomena are but little understood. The purpose of the present paper is to clarify the problem through the application of a simple principle, and to show that, through the application of this principle, a number of phenomena in the plastic deformation of metals become more readily understood. The principle is this: During homogeneous flow, the rate of work-hardening is greater than the rate of change of stress resulting from change

Jan 1, 1938

[ ]

Jan 1, 1938

By J. F. Myers, F. M. Lewis

THE selection of the proper type of flotation machine involves the consideration of a wide variety of factors. Under any condition, all types of machines will promote some kind of separation. Obviously, the correct way of deciding which type of machine is best suited for a particular problem would be to set up all types of machines and test them out in a competitive manner, but the vast number of small concentrating plants are unable to make such complete and exhaustive tests. The experience of the authors of this paper indicates that if all the factors involved in any particular problem can be determined, and if all the flotation-machine characteristics are understood, some basis for selection could be arrived at other than actual comparison. This paper is presented to show how the process factors and machine characteristics have been combined at the mills of the Tennessee Copper Co. from studies of several types of flotation machines. At the two mills of the Tennessee Copper Co. in the Ducktown Basin of Tennessee, four distinct flotation separations are made on the complex sulphide ore. Three different concentrates are produced from the ore-in the order of their importance: iron concentrate, copper concentrate, and zinc concentrate. Four different types of flotation machines are used. The selection of these four machines, for the plant operation, was based upon the study and operating experience of the machine units shown in the following list: Fagergren machine; square cell, size 56 inches Fagergren machine; level type, size 56 inches Denver machine; conical disk impeller, size 24 inches Denver machine; receded disk impeller, size 24 inches Minerals Separation Sub-A, size 24 inches Munro-Pearce deep cell, pneumatic Southwestern air machine, Hunt principle To date the study of flotation machines has been confined almost entirely to the rougher circuits. The various cleaning operations, being relatively a much simpler matter, have not been investigated so thoroughly. Table 1 shows a typical analysis of the two ores as well as of the mineral content. []

Jan 1, 1944

By Frederick W. Bacorn

The paper of Reno H. Sales on Ore Deposits at Butte, Mont.,' is a careful and painstaking work, an important contribution to the literature of the subject. As is almost inevitable in a work of such magnitude, a few misstatements occur; and some of these I shall endeavor to point out. Mr. Sales has also fallen into error, as I think, in the application of his theory of ore deposition; and while the modification which I venture to suggest is a minor one geologically, it is of great economic importance. I refer to Mr. Sales's idea of an outward migration of mineralizing solutions from a supposed central copper zone. In order that I may make myself plain, I must first epitomize the theory as a whole, which I understand to be this: All of the Butte ore deposits (save those along the Continental fault, not herein considered) are derived from solutions of magmatic origin, which, at the beginning of their ascent from a great depth, were acid in reaction, hot, and were carriers of copper, zinc, manganese and other metals. As they departed from their point of origin they lost heat, and, because of reactions with the wall rock, became more and more alkaline. The metal deposited from these solutions in their hot condition was principally copper; and, as they cooled, they deposited less and less copper and more and more manganese and zinc, until the copper practically disappeared. With this theory in general I have no fault to find, nor have I, it must be stated, the qualifications necessary to enable me to pass upon it critically; but it seems to me to be reasonable and probable, and is one which I am quite willing to accept. But Mr. Sales, for what seem to me to be insufficient reasons, has assumed that there is one deep central source of copper, relatively rich and small, from which all the solutions emanated. From this central source the solutions rose, through one channel or through a group of channels, to the surface, at and within a small area called the central copper zone,

Jan 1, 1915

By Richard A. Pomeroy

This mine, known also as the A very Mine, is situated on Petite Anse Island, Iberia Parish, Louisiana. The island is about four miles from Vermillion Bay, an arm of the Gulf of Mexico, and is one of four islands or hills surrounded by the sea-marsh, as shown in the accompanying map. (Fig. 1.) A fifth, Joe Jefferson's Island, or hill, is some distance from the sea-marsh. These five islands: Belle Isle, Cote Blanche,Grand Cote, Petite Anse and Jefferson, appear to be the tops of submerged hills, and occupy a line having nearly a northwest trend. To the north are a series of hillocks that extend at intervals to the hills of Northern Louisiana, which in turn appear to run into the Ozarks of Arkansas. Near the mine there is sandstone, also a thick vein of lignite. Bones of the mastodon have been

Jan 1, 1889

By W. B. Vietz, C. W. Hill, T. P. Thomas

FLUXES, in general, may be classified according to their use as soldering, foundry or casting, and metallurgical and the chemistry of their action follows quite closely this division. The term foundry or casting fluxes, as used here, refers to the substances added to molten metals, preparatory to casting into molds or ingots, with the object of removing small amounts of impurities that have been introduced in handling or melting the metal, which was placed in a fair state of purity by the previous refining or metallurgical processes. The sources of these impurities are the oxide coating on the surface of the ingots, material extracted or mechanically removed from the crucible or furnace wall, and those formed by the reaction of the molten metal with the heating gases or furnace atmosphere. As commonly used, the term fluxes is applied to such materials as ammonium chloride, zinc chloride, salt, borax, and boric oxide. A second class of materials, usually called deoxidizers, includes substances such as metallic phosphides, sub-oxides, carbides, and bo-rides, that reduce the metallic oxides present in the metal. A third class includes various compounds that arc molten and non-volatile at the temperature of the molten metal and are used primarily to protect the surface of the metal from the action of the furnace or exterior atmosphere; to this class belong such mixtures as lime and fluorspar, lime and soda ash, various minerals, etc. In some cases these protective layers may act in a manner similar to the metallurgical fluxes and dissolve or unite with the oxide impurities of the metal, but as generally employed this latter action is negligible since there is little opportunity for the coverings to come into contact with more than the surface of the metal, and hence they arc without action on the body of the molten mass. The use of fluxes is the result of factory experience and tradition, but an extensive study has not been made of the chemical and physical actions that occur or the effects of these actions on the properties of the metal. It would seem necessary in any successful study of metal fluxes to determine not only what impurities are present in metals melted under

Jan 1, 1921