Search Documents

Jan 1, 1900

By Robert Bell

The Tar-Sands" is the name which has been given to the extensive horizontal deposit of fine Cretaceous sand, blackened by tarry petroleum, which forms the banks of the last or lowest 130 miles of' the Athabasca river before it terminates in Athabasca lake. The Cretaceous strata, to which these sands belong, extend northwesterly from Dakota all the way to this lake and for 500 miles beyond it. The Athabasca river forms the uppermost section of the Athabasca-Mackenzie, one of the great rivers of the world. It rises on the Pacific side of the Rocky mountains, westward of Edmonton, and flows north of east to a point called Atha-basca Landing, 100 miles north of Edmonton, where it turns northward and runs about 280 miles before it falls into the west end of Athabasca lake. The section of this river-system which discharges the lake just named into Great Slave lake, is called Slave river, and below the latter lake it becomes the Mackenzie river. Along the section of 280 miles of the Athabasca river above mentioned, the Cretaceous strata consist of bluish-gray and drab-gray marls, on top, from Athabasca Landing to Drowned rapid, 110 miles down stream; then heavily bedded gray sandstones, 225 ft. in greatest thickness, underlying these, form the banks for about 40 miles further. The strata appear to be horizontal, but they really dip very slightly to the southward. At Drowned rapid, we see the first of the tar-sands resting on almost horizontal beds of bluish-gray limestone of Devonian age. In some places the limestone is associated with shaly or marly bands. Notwithstanding the great hiatus between the two series, the horizontal tar-sands lie conformably upon the almost level upper beds of the limestone wherever the two formations are seen together, all along the river, throughout a

Jan 1, 1908

By Rajaraman V. Ramani, K. Sinha Atmesh, Robert Stefanko

Use of electrical power in the bituminous mining industry has increased many fold during the last few decades. Rapid changes have also occurred in mine electrical power systems in order to meet the demands from highly mechanized mines. Fires, explosions, and deaths due to electrocutions are the primary hazards due to the underground use of electricity, although there has been a marked decrease in the fatality rate from electrical accidents. However, efforts to eliminate electrical hazards and to insure trained manpower for better distribution, utilization, and protection of the electrical systems cannot be relaxed. In this article, 200 fatal accidents that occurred during the period from 1955 to 1970 have been analyzed. Accident frequency has been correlated with the size of the mine and of the work force, and with age and work and task experience. A strong negative correlation has been established between task experience and accident frequency. Though the available data permitted only a limited analysis, need for improvements in electrical power technology and for better education and training has been identified and discussed. Missing information in accident statistics is outlined and suggestions for better hazard analysis are presented.

Jan 1, 1975

By John H. Ratcliffe, Hans T. Lundberg

In airborne gravity surveys effects of acceleration and irregular movements of the aircraft must be balanced out or overcome. The gradient of vertical gravity is recorded, therefore, by using two masses instead of one. As the amplitude variations are infinitesimal and difficult to measure accurately, at of gradient during flight is positive or negative. The positive portions of the pattern can then be indicated and contoured. Even with these simplifications, the source of energy must be exceptionally stable. General Principles: In the conventional gravimeter the weight of a standard mass is determined at a number of selected points within the survey area. In most systems weight is determined by comparing the gravity pull with extension or torque produced in a wire spring. The instruments employed are sensitive to the slightest movement; they cannot be used on a moving platform unless velocity is kept strictly uniform.

Jan 8, 1959

By John W. Cahn

IT is well established that the pearlite reaction is a nucleation and growth reaction, and that pearlite nucleates on grain boundaries or intersections of grain boundaries. It is also known that while the

Jan 1, 1958

By Sterry Hunt

The American Institute of Mining Engineers, and American science in general, have sustained a great loss in the death of Prof Benjamin Silliman, deceased at New Haven, Connecticut, on the 14th of January, 1885, at the age of sixty-eight. But a month has passed since, as one of the pall-bearers, I paid the last tribute to the remains of my old friend and honored master.

Jan 1, 1885

By E. G. Woodruff

Few authors of treatises and papers on engineering subjects hare given adequate attention to topographic maps. The statement applies especially to mining engineering in all branches. Even those who have discussed such maps have treated the subject only in a general way. Therefore it is proposed to outline in this paper a few of the uncommon yet important relationships which topographic maps and their by-product, structure-contour maps, have to modern methods of mining investigation and development when the facts depicted on such maps are properly interpreted. Topography, as suggested by the etymology of the word, means a detailed description of particular places. Written descriptions have been found less effective than the pictorial representations, therefore attempts have been made in various ways to picture the surface features of places. Lines and shading have been used, hachures drawn, and, finally, the contour topographic map. To a large extent this style of map is the result of the demands of engineers. It is designed to meet their needs far more than those of the man untrained in engineering. In fact,. the average man obtains a better idea of the topography of an area from the hachure system than from contour maps. Since the maps have been made chiefly for the use of the engineer, they ought to meet his demands on the one hand, and, on the other, should be used by him to the fullest extent. Such maps, when properly made, accurately portray a portion of the earth's surface and should present the topography better than a personal examination of the area without a map could present it, because the person making such examination views only a limited portion of the surface at a time, and estimates distances only roughly with his eye. Let the engineer consider carefully the fact that in many instances the topographic map is superior to a personal examination of the surface features of a property because the map is based on careful instrumental measurements, whereas the eye gives imperfect data because it can be used merely for the estimation and

Jan 1, 1914

By Robert A. Campbell, Robert J. Brison

The problem of optimizing from an economic standpoint the capacity of grinding equipment in the design of a new concentrator is discussed. Although directed specifically to copper flotation mills employing conventional wet, grinding, the material presented is considered applicable with modifications to other types of ores and other grinding methods. A general approach to optimizing the grinding capacity is outlined and illustrated by an example. The' interrelation between grinding capacity and other aspects of the project is considered. The problem of regrind capacity and its relation to preceeding and subsequent processing steps is also discussed. Finally, factors are considered that may, in certain cases, dictate modifications of the suggested approach.

Jan 1, 1974

By Simon D. Strauss

INTRODUCTION The changes in ownership, management, and operation of the non-fuel minerals industry since the Second World War have been dramatic. World-leading enterprises have lost their identity; host countries have taken over operations from multi-national firms; marketing practices have been drastically altered - and yet the world industry is supplying minerals on a scale far greater than had been anticipated in projections made at mid-century. The world's known mineral resources have been enormously expanded, despite the doom sayers who for decades have been predicting that depletion of non-renewable resources would impose limits to growth. PALEY REPORT One can set the stage by reviewing how the minerals outlook was regarded in a thoughtful and comprehensive analysis made in the years 1950 and 1951. During the War years, President Harry Truman of the United States had come to appreciate the decisive role played by minerals resources through his chairmanship as a U.S Senator of a committee that investigated the procurement and allocation of natural resources. In 1950, in the Cold War era that resulted in actual military conflict in Korea, he appointed a prestigious five-man commission to study the problems of Materials Policy over the following quarter century. Their findings, published in five impressive volumes in early 1952, became known as the Paley report. The text was prepared by expert scientists and economists who spent 18 months assembling statistics, making projections of future demand, and interviewing leaders in industry, academia, and government. [ ] The Commission had correctly foreseen that aluminum would replace copper as the largest volume non-ferrous metal, but it had fallen short of reality by a wide margin indeed for all three materials. Even though the Commission's expectations for growth proved to be extremely understated, it had concluded its report with grave foreboding about the effect of its estimates of demand in relation to supply, as follows: "Consumption of almost all materials is expanding at compound rates and is thus pressing harder and harder against resources which, whatever else they may be doing, are not similarly expanding. This materials problem is thus not the kind of 'shortage' problem, local and transient, which in the past has found its solution in price changes which have brought supply and demand back into balance. The terms of the materials problem we face today are larger and more pervasive." With respect to some minerals, the Paley Report expressed scepticism that, in fact, supplies would be forthcoming regardless of price. Because the Paley demand forecasts understated the actual growth in demand for virtually every mineral, one could logically have expected frequent and protracted shortages in the years since 1950.

Jan 1, 1985

By E. E. Carpenter

(San Francisco Meeting, September, 1915) BELIEVING that the results accomplished in the mill of the Churchill Milling Co., Wonder, Nev., during the fiscal year ended Sept. 30, 1914, will be of interest, I am presenting the more prominent facts and figures showing the progress made in treating this ore with especial reference to tonnage, supplies, costs, and extractions. The mill is situated at Wonder, Nev., in the Wonder mining district, 55 miles east from Fallon, Nev., the nearest railroad point. All supplies are hauled this distance by freight teams, this method of transportation having been found more reliable for continuous service than trucks, the price paid for hauling being slightly under one cent per pound. In this mill are treated the ores of the Nevada Wonder Mining Co. ,

Jan 6, 1915

By Michael J. Messel

The critical shortage of asbestos fiber in the world today brings to the foreground the question of locating and developing new deposits. The object of this paper is to discuss some of the more important factors which should be considered in the examination and valuation of a new asbestos enterprise. Some of the more important uses of asbestos fiber are for textiles, heat insulators, building materials, filters and a series of other uses. The properties of this mineral, such as fibrous structure, color, strength, silkiness and flexibility, coupled with resistance to fire, certain chemical action and decay make its application unique for certain industrial uses which consume over 500,000 tons annually. These same unique properties which make this mineral so valuable also make a deposit one of the most difficult to appraise accurately, because of the many undeterminable and varying factors which must be considered before a deposit can properly be termed commercial. The majority of the asbestos fiber today, having the above mentioned properties, is sold by grades which are based on fiber length. Present day fiber prices vary over a wide range from $800 to $225 for crude fibers and $300 to $20.00 per ton for milled grades. For valuation purposes a careful study should be made of existing fiber prices and markets. Examination of Deposits In carrying out prospecting and examination of a deposit, considerable caution is required to get the necessary information in the form that will have the most value for the final determination. There are two main classes of asbestos fibers, chrysotile and the amphiboles, the chrysotile being, by far, the most important both in abundance and uses. This paper will stress mainly chrysotile deposits, however, the amphiboles have many important uses, especially amosite and crocidalite. Their valuation presents special problems as other factors may be involved, especially as they are not graded according to any well defined and adopted standard but usually according to the use for which they are being supplied. Most chrysotile deposits occur in two main types of rock, (I) mainly in basic igneous, such as dunite and peridotite, (2) to a lesser extent in sedimentary rocks, such as dolomite and limestone. All of these require a certain degree of metamorphism to be favorable to asbestos formation. Approximately 90 pct of the asbestos deposits are derived from serpentinization of dunite or peridotite, whereby the magnesium-silicate olivine was altered to hydrous magnesium-silicate serpentine. Under certain favorable geological conditions, this serpentine takes a fibrous form having a definite crystal structure, probably due to molecular rearrangement, and is known as chrysotile. The fiber veins are usually ir-

Jan 1, 1948

By Michael J. Messel

The critical shortage of asbestos fiber in the world today brings to the foreground the question of locating and developing new deposits. The object of this paper is to discuss some of the more important factors which should be considered in the examination and valuation of a new asbestos enterprise. Some of the more important uses of asbestos fiber are for textiles, heat insulators, building materials, filters and a series of other uses. The properties of this mineral, such as fibrous structure, color, strength, silkiness and flexibility, coupled with resistance to fire, certain chemical action and decay make its application unique for certain industrial uses which consume over 500,000 tons annually. These same unique properties which make this mineral so valuable also make a deposit one of the most difficult to appraise accurately, because of the many undeterminable and varying factors which must be considered before a deposit can properly be termed commercial. The majority of the asbestos fiber today, having the above mentioned properties, is sold by grades which are based on fiber length. Present day fiber prices vary over a wide range from $800 to $225 for crude fibers and $300 to $20.00 per ton for milled grades. For valuation purposes a careful study should be made of existing fiber prices and markets. Examination of Deposits In carrying out prospecting and examination of a deposit, considerable caution is required to get the necessary information in the form that will have the most value for the final determination. There are two main classes of asbestos fibers, chrysotile and the amphiboles, the chrysotile being, by far, the most important both in abundance and uses. This paper will stress mainly chrysotile deposits, however, the amphiboles have many important uses, especially amosite and crocidalite. Their valuation presents special problems as other factors may be involved, especially as they are not graded according to any well defined and adopted standard but usually according to the use for which they are being supplied. Most chrysotile deposits occur in two main types of rock, (I) mainly in basic igneous, such as dunite and peridotite, (2) to a lesser extent in sedimentary rocks, such as dolomite and limestone. All of these require a certain degree of metamorphism to be favorable to asbestos formation. Approximately 90 pct of the asbestos deposits are derived from serpentinization of dunite or peridotite, whereby the magnesium-silicate olivine was altered to hydrous magnesium-silicate serpentine. Under certain favorable geological conditions, this serpentine takes a fibrous form having a definite crystal structure, probably due to molecular rearrangement, and is known as chrysotile. The fiber veins are usually ir-

Jan 1, 1948

By H. Carroll Weed

By caving a block into the workings of its open pit and using the block as an ore transfer, the Inspiration Consolidated Copper Co. has solved a transportation and sizing problem, making possible a great expansion of open-pit methods as applied to Inspiration ore- bodies.

Jan 9, 1953

By M. G. Nicholas

The influence of deformation, relative movement and surface cleanliness on the strength of room -temperature "interparticle" bonds between copper surfaces has been studied. No bonding resulted when clean surfaces were merely pressed together, even under pressures of 50,000 psi. Bonding resulted, however, when clean surfaces were simultaneously pressed and moved relative to each other, some bonding occurring no matter how small the pressure or relative movement. Exposure of the clean surfaces to various chemicals inhibited bonding, none at all being produced by small relative movements. The size of the movements which first produce bonding between exposed surfaces depends on the nature of the chemical, being less than 0.002 in. for cleansing reagents and greater than 0.004 in. for lubricants, water and hydrogen sulfide. It is concluded from the experimental data that the prime requirement for bonding is the dispersal of surface films such as oxides and adsorbed contaminants. THE formation of interparticle bonds during the room-temperature compaction of powder metallurgy components greatly increases the ease of handling in subsequent production operations prior to sintering. The strength of unsintered compacts follows the same general trends as their density and hardness, but quantitative data are extremely Scarce. Quantitative correlation of the data on the overall strength of a compact with that of the individual interparticle bonds is virtually impossible due to the extremely complex geometry of powder compacts. Qualitatively, however, the strengths of unsintered compacts can be correlated with variations in parameters known to influence the extent of cold bonding, and hence interparticle bonding, such as surface cleanliness, relative movement, and deformation of the mating surfaces. Kuzmic and seelig4 found that contamination of powder particle surfaces with lubricants reduced the strength of unsintered iron and copper compacts. Interparticle shear has been shown to promote bonding by Train and Hersey7 while Gregory has shown that die rotation is beneficial. Eilender and schwalbe6 concluded that most bonding occurred during the early stages of pressing iron powder compacts when interparticle shear is one of the principal processes occurring. mile there can be little doubt that these and other factors, such as particle size and shape, affect the extent of interparticle bonding produced by compaction, evaluation of the influence of individual factors is not easy. Particle deformation and relative movement, for example, occur simultaneously during compaction, making any precise measurement of their relative influences difficult. Because of these and other difficulties encountered in studying interparticle bonding in actual powder compacts, the approach adopted in this study was to

Jan 1, 1963

By Fred Bond

THERE is acute need for a method that will measure the size distribution of finely di-vided materials, particularly when the par-ticle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the sam-ples produced are adequate for a consider-able amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essen-tially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the set-tling rate. The balance appears to be in-herently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have re-stricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investiga-tion might lead to modifications that would make it a valuable tool for the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribu-tion determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used, in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared, early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could he accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the dis-tribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1939

By Harold M. Mooney

RESISTIVITY measurements for determining depth to bedrock, water table, and other geologic discontinuities have had only limited success. Many of the difficulties can be attributed to complex geology and to basic limitations of the method; current flow through a continuous medium is a diffusion phenomenon, emphasizing irregularities near the source and smoothing out those at a distance. Some of the failures, however, are due to careless field work and incompetent interpretation. A forthcoming publication1 may help to reduce difficulties of this sort. The writer here attempts to bring order into the multiplicity of interpretation methods and, to a limited extent, to evaluate them. For all methods, the field data to be interpreted consist of apparent resistivity values plotted against electrode separation, Fig. 1. The interpretation should give depths to one or more geologic horizons. Direct currents and the Wenner four-electrode configuration will be assumed, since these are widely used, although the interpretation problems remain essentially the same for other electrode configurations. Alternating currents higher than, say, 20 cycles per second introduce complications beyond the scope of this paper. Three approaches to the interpretation problem have been used. These may be called empirical, theoretical curve matching, and direct. Many techniques have been proposed, but each can be reduced to one of these approaches and to a single geologic idealization. This idealization rests on the following assumption: the earth in the limited volume of interest can be approximated by a horizontal sequence of layers, each homogeneous and isotropic in its electrical properties. This seemingly restrictive assumption has proved to have practical value, although future work should aim at removing some

Jan 1, 1955

By J. H. Nelson

An outline survey of the economic outlook for the United States export trade in petroleum products resolves itself broadly into two general divisions; first, a consideration of our present position in this trade, and second, a discussion of the visible factors which promise to affect appreciable changes in the immediate future in that trade. The United States PetRoleum Exports of majoR Petroleum Products 1925, 1926 and 1927

Jan 1, 1928

By Oliver C. Ralston, James E. Norman

Separation of minerals by froth flotation is rightly called an art. It can truthfully be said that no two ores separate in the same way. The difference in results obtained when natural and synthetic mixtures of minerals are separated is so great that such tests frequently have been worthless in attempting to select conditions in which a natural mixture will separate. With a few rare exceptions, the natural mixture is much more difficult to treat than a synthetic mixture, and a much poorer separation is obtained. Perhaps several experimenters have wondered why 10 or 20 per cent of a mineral being floated from an ore does not float and is different from the 90 or 80 per cent that is recovered. In experimental tests on pure sphalerite, observers' have noted that varying amounts of sphalerite may be froth-floated with pine oil alone, the amount recovered in the froth depending apparently upon the source of the sulphide. The only explanation of results such as these, barring insufficiency of frother or time of flotation, is that the surface of the mineral floated is different from that of the mineral depressed. This difference often has been found to be caused by natural contamination of mineral surfaces, apparently brought about by weathering and exposure to natural solutions. There is virtually no rock that is absolutely unweathered. One of the writers had an exceedingly instructive experience in 1931 while working with United Verde copper-zinc iron sulphide ore in Arizona. Nonselective flotation of chalcopyrite and sphalerite away from some of the pyrite was all that could be accomplished. All known depressants produced only slight effect. Sodium cyanide showed some effect, but so much had to be used that only a small amount of chalcopyrite could be

Jan 1, 1939

By Oliver C. Ralston, James E. Norman

Separation of minerals by froth flotation is rightly called an art. It can truthfully be said that no two ores separate in the same way. The difference in results obtained when natural and synthetic mixtures of minerals are separated is so great that such tests frequently have been worthless in attempting to select conditions in which a natural mixture will separate. With a few rare exceptions, the natural mixture is much more difficult to treat than a synthetic mixture, and a much poorer separation is obtained. Perhaps several experimenters have wondered why 10 or 20 per cent of a mineral being floated from an ore does not float and is different from the 90 or 80 per cent that is recovered. In experimental tests on pure sphalerite, observers' have noted that varying amounts of sphalerite may be froth-floated with pine oil alone, the amount recovered in the froth depending apparently upon the source of the sulphide. The only explanation of results such as these, barring insufficiency of frother or time of flotation, is that the surface of the mineral floated is different from that of the mineral depressed. This difference often has been found to be caused by natural contamination of mineral surfaces, apparently brought about by weathering and exposure to natural solutions. There is virtually no rock that is absolutely unweathered. One of the writers had an exceedingly instructive experience in 1931 while working with United Verde copper-zinc iron sulphide ore in Arizona. Nonselective flotation of chalcopyrite and sphalerite away from some of the pyrite was all that could be accomplished. All known depressants produced only slight effect. Sodium cyanide showed some effect, but so much had to be used that only a small amount of chalcopyrite could be

Jan 1, 1939

By P. Hazebroek, M. Prats, E. E. Allen

Well locations in water floods frequently do not coincide with the ideal well locations associated with the flood pattern which is used. A question of importance is. "How much oil is lost because of this?". This is the problem treated in this paper. It is assumed that each pattern in a five-spot flood has the proper number of production and injection wells but that the wells may be off-pattern. The distance by which a well is off-patern is given in terms of the pattern spacing, defined as the length of one side of a five-spot. The influence of off-pattern wells on the performance of a five-spot flood has been investigated mathematically for unit mobility ratio. All production and injection rates are assumed to remain equal. The loss in recovery resulting from pattern irregularitie: has been calculated at a cumulative water injection corresponding to a 98 per cent water-cut in a regular five-spot. Displacing a single production or injection well by about one-third the pattern distance reduces the total field recovery by 4.4/N per cent of the recovery obtainable with regular spacing, where N is the number of five-spots in the flood (assumed large). When off-pattern wells are separated by at least one regular five-spot and are displaced by less than one-third the pattern distance, the total loss in recovery in a large-scale flood is, at most, 1 per cent of the recovery obtainable from that field with a regular five-spot pattern. However, much higher losses may occur if the off-pattern wells are not separated by a regular five-spot, if the rates are imbalanced, or if the mobility of the injected water is higher than that of the crude. Although the loss in oil recovery due to pattern irregularity often may be low, the off-pattern case will always require injection of more water to reach the same final water-cut. The volume of water injected per unit volume of oil displaced has been calculated for each five-spot adjacent to a five-spot containing a single 08-pattern well. The cumulative water injection at the time of 98 per cent water-cut may be increased by as much as 37 per cent when a production well is displaced one-third the pattern distance toward an injection well. The existence of differences between actual subsurface locations and the idealized well patterns used in secondary recovery operations is well recognized. However, the methods commonly used for predicting waterflood behavior ignore such differences, even when subsurface locations are known. The reason for this is simple. The idealized well patterns are highly symmetrical and, as such, the production history of the pattern (and even of the field) can be determined from that of a few production wells—usually from only one. Consideration of the many irregular well spacings found in a specific field would entail a large amount of work, and then the results would be applicable only to that specific field. In an attempt to provide an answer to the more general problem, this paper considers a water flood having an idealized well pattern, except for one well which is not at its regular location. When several off-pattern wells are present, their contributions are assumed to be additive unless the off-pattern wells are close to each other. Only four positions of the off-center well (at x, y. of Fig. 1) are considered in this paper. These are shown