Search Documents

By E. S. Tankins

The main purpose of this work was to study the effect of gold on the activity coefficient of oxygen in the liquid Fe-Au alloy and to determine how copper and silver change the activity coefficient of oxygen. A preliminary investigation has been made of equilibrium in the reaction of hydrogen with oxygen in some of the liquid gold alloys. The experimental method, which has been described in detail elsewhere,' consisted of bubbling accurately known H-A-water vapor mixtures through the Fe-Au alloys contained in alumina crucibles within a vertical closed furnace. When equilibrium was reached, the samples were quenched by rapidly lowering the crucible under an atmosphere of argon to a water cooled brass fixture at the bottom of the furnace tube. The melts were found to freeze from the top in less than 4 sec. The heats were carefully prepared for oxygen analysis. The oxygen content was determined by vacuum fusion analysis.' Only high purity electrolytic materials were used in this investigation. The activity and free energy of oxygen in the liquid iron alloys were studied by means of the reaction; The data for the 80 Fe-Au alloys, obtained as a function of temperature, are summarized in Table I and presented in Fig. 1, where log is plotted against . The results can be expressed by: The data were obtained using water vapor-hydrogen ratios between 0.04 and 0.30, and a 25 pct H2-75 pct A mixture. An oxygen content between 0.030 and 0.060

Jan 1, 1970

By Effingham Humphrey

THE Lehigh Valley. Coal Co. finished the rebuilding of its Drifton No. 2 breaker at Drifton, Pa., in the summer of 1917. The new construction comprises an addition and the complete remodeling of the old breaker. It is of interest to note that the old structure was the first iron breaker erected in the anthracite region. THE OLD BREAKER This old breaker was built by the Cross Creek Coal Co., under the direction of the late Eckley B. Cole, in 1888-89, and was fully described by him in the Transactions.1 The columns were cast iron, 8,'10 and 12 in. square. The floors and partitions in pockets were cast-iron ribbed plates. The struts were cast iron of "H" section; the other members were of structural iron either rolled I-beams or built-up sections. The sizes of the rolled beams varied from 6 to 20 in. deep, while the built-up sections, made of plates and angles, varied from 6 to 63 in. in depth, so that there apparently was no rule to determine the type of section used. In the remodeling of the old structure, practically everything was taken clown excepting the columns and roof, and such beams as were necessary for temporary construction purposes, and, therefore, a close inspection of the old structural members could be made and the effect of the acid water oil them could be noted. The cast-iron members were but slightly attacked by the water, while the wrought-iron beams, in the wet places, were corroded almost to failure.

Jan 2, 1918

By M. D. Cooper

UNDERGRADUATES in mining engineering may be prepared for work by giving them sound instruction in the courses generally considered essential to the profession. The industry is not deeply concerned about the details of those courses. The average man in the coal industry does not wish to insist upon a rigid program. Therefore, he differs little from those in the teaching profession-who evidently are not unanimous in their opinions, or all college catalogs would be alike. For the good of the profession, it is just as well that there should be differences in regard to details. It appears that students graduating in mining engineering from the accredited institutions receive similar instruction.

Jan 1, 1950

By F. H. Buttner, E. R. Funk, H. Udin

A. P. Greenough (University College, swansea, Great Britain)—I have recently made some experiments on the deformation of silver wire at high temperature in an atmosphere of oxygen-free nitrogen. The observa-tions which 1 made confirm the main conclusion of this paper, that the most satisfactory mechanism so far suggested to explain the deformation which takes place

Jan 1, 1953

By William M. Bowron

An interesting calculation was made at the Chattanooga Meeting of 1885 as to the cost of making a ton of pig-iron in the Chatta-

Jan 1, 1889

By R. W. Raymond

The sudden death of Captain Jones, September 28,1889, became known to his fellow-members on the eve of the Ottawa meeting of the Institute; and at that meeting, Mr. Charles Albert Ashburner, of Pittsburgh, expressed with unaffected feeling and unpremeditated eloquence the sorrow of all. Mr. Ashburner subsequently undertook to revise and extend, for in in the Transactions, the remarks he had made at Ottawa; but death surprised him also, in the midst of his labors; and it has become my duty and privilege to prepare from the memoranda he left behind, the present brief and inadequate notice. To me, who knew and loved them both, this task of double sorrow recalls them both, with a peculiar sense of presence and of absence. They seem to speak from another land, not far away, yet not with human voices—like an echo and its echo. William Richard Jones was born in Luzerne county, Pennsylvania, February 23, 1839. His father was Rev. John G. Jones, a Welsh minister, who had immigrated to the United States in 1832. William was the eldest son, and his father's failing health made it necessary for him to begin early the work of self-support. At the age of ten, he was apprenticed to the Crane Iron company, of Catasauqua, and in this humble capacity entered upon the profession in which he was to become famous. Unquestionably, the thorough acquaintance with all details, acquired by working his way from the bottom to the top, was one secret of the conspicuous executive ability which characterized him in the height of his career. According to a letter from Mr. J. H. Geer, Assistant Chief Engineer of the Cambria Iron Company, Mr. Jones entered the service of that company in 1858 or 1859 as a machinist, and continued to work in that capacity until July, 1862, when he enlisted as a private in the 133d Regiment of Pennsylvania Volunteers, in which he afterwards commanded a company. The regiment was mustered out of service in 1863, and Captain Jones re-enlisted in the 194th

Jan 1, 1890

By Albert F. J. Bordeaux

This paper briefly describes the general outline of cyaniding silver-ores in Mexico, with special reference to personal experiments made in the Temascaltepec district. The most important papers on the subject deal with cyaniding gold-silver ores, the gold predominating in value, so that the treatment is nearly the same as for gold-ores, the losses of silver being considered of little importance. I describe here the treatment of silver-gold ores containing very little gold, which is more general in Mexico than elsewhere. The cyanide treatment, which was so successfully applied to gold-ores, did not succeed immediately with silver-ores on account of their varying composition. Gold occurs in nature usually in the native state, while silver occurs generally in combination with sulphur (argentite), and various combinations of sulphur, antimony, and arsenic. In former times there mas a complete difference in the treatment of gold-ores and silver-ores. Amalgamation, which was successful with gold-ores, was generally inadequate with silver-ores. The usual treatment in Mexico for silver was the patio process, the theory of which was satisfactorily explained only quite recently by Mr. Ortega and others. General Outline of the Cyanide Treatment. The general tendency of the present practice is to slime the silver-ore as much as possible, and in order to obtain a higher efficiency, with less loss of cyanide, and greater speed, the following lines are observed: 1. Crushing by stamps with 30- or 40-mesh screens, then crushing by Huntington or Chilean mills, through 60- or 80-mesh screens. 2. Concentration upon vanners.

Jan 1, 1910

By R. M. Zimmerman

INTRODUCTION Tuff is being considered as a possible geologic median for the underground storage of commercial high level radioactive wastes by the Department of Energy (DOE). DOE has the responsibility for developing or improving the technology fir safely and permanently isolating these wastes. DOE programs must satisfy requirements established by the Nuclear Regulatory Commission (NRC) for the licensing and regulating of these storage facilities (NRC 1981). Pertinent draft NRC requirements are: 1) releases of radioactivity to the environment must be within prescribed limits and 2) emplaced canisters containing wastes must be retrievable up to 50 years following emplacement. High level radioactive wastes produce heat in storage and it is essential that the thermal/mechanical/hydrological response of the host rock will not significantly degrade either the structural performance o£ the repository or the ability of the natural or engineered barriers to retard radionuclide migration. The Nevada Nuclear Waste Storage Investigations (NNWSI) was established by DOE to evaluate the suitability of disposing of high level nuclear wastes on or near the Nevada Test Site (NTS) (NNWSI 1980). NNWSI has focused exploration and site evaluation on the tuffs of Yucca Mountain. Field testing is essential to support site characterization and repository design efforts. Preliminary studies have been conducted indicating that tuffs in G-tunnel on the NIS contain welded and nonwelded tuffs that have similar properties to those in Yucca Mountain. Thus, field testing can be accelerated. This paper discusses the issues supporting the planned field experiments in G-tunnel. Issues not related to rock mechanics are not included.

Jan 1, 1982

By G. W. P. Rengstorff, H. B. Goodwin

A method is described for purifying iron in batches of 150 Ib or more. Oxygen, carbon, nitrogen, and sulphur are removed from flakes of electrolytic iron by treatment in wet and then dry hydrogen. A special consumable-electrode arc furnace is used to remove hydrogen and to melt the flakes into ingots. A LTHOUGH iron and steel have been made and used for hundreds of years, there are still wide gaps in the knowledge of these metals. One reason for this is that the true properties of the base metal, iron, are not well known, simply because really pure iron has never been readily available for research purposes. Commercial iron, and even the "pure" irons which are readily available, are really complex alloys of iron with oxygen, nitrogen, hydrogen, carbon, sulphur, silicon, and other elements. With such materials, it has not been possible to prepare steels and other iron-base alloys in which all elements are present in exactly controlled amounts. It is an almost impossible task to determine the separate effects of each element or the intereffects of several elements unless alloys can be prepared containing only the desired elements. The ability to make controlled alloys of low impurity content is of far more than academic interest. It will assist in the study of such practical problems as the brittle failure of ship hulls or high pressure gas pipelines, determination of the factors which affect the deep-drawing properties of steels, the improvement of magnetic and electrical properties, the phenomenon of aging, and many others. In 1949, the American Iron and Steel Institute asked Battelle Memorial Institute to prepare high purity iron on a larger scale than had been attempted up to that time. The work was directed toward the preparation of iron as low as possible in carbon, oxygen, nitrogen, hydrogen, and sulphur because these are the contaminating elements of major interest in many research investigations on iron-base alloys. The initial goal was to prepare iron with not more than a few thousandths of one percent of each of these impurities. The purpose was to set up a "bank" of high purity iron on which researchers could draw when a supply was needed and which could be replenished from time to time as the stock became depleted. Of several possible purification methods, heating in hydrogen was selected as the most promising for the removal of both carbon and oxygen from solid iron. Metallic impurities are not removed by hydrogen. Electrolytic iron was chosen as a starting material because it is the most readily available form of iron low in metallic impurities. Decarburization and desulphurization were obtained by annealing in wet hydrogen at relatively low temperatures. The optimum temperature, as found by previous investigators,' is about 1400°F. This treatment also removes nitrogen. Deoxidation is favored by dry hydrogen and higher temperature. There is evidence from previous work that an anneal at 2200°F in dry hydrogen will deoxidize the iron, reduce the nitrogen content, and reduce the sulphur content. These facts suggested the use of a two-stage process: treatment in wet hydrogen followed by treatment in dry hydrogen. To carry out the purification process in a reasonable time, it was necessary that the iron be in thin pieces. Flakes of electrolytic iron were used. Because most research requires that the iron be in massive form, it was nccessary to melt the purified iron to consolidate it into large pieces. For this work, it was decided to prepare ingots weighing at least 15 lb by using a cold hearth arc-melting process in which the iron was melted in an inert atmosphere of argon or helium. This method of melting was selected because the water-cooled copper crucible is not wet by the iron and does not contaminate it as a refractory crucible would. Because the crucible is also the ingot mold, contamination from mold materials was also eliminated. Contamination from electrodes was avoided by making them from purified electrolytic iron. The melting procedure finally developed was an adaptation of the Kellogg electric ingot process.' Two batches of purified iron weighing about 100 Ib each in ingot form were prepared with analyses as shown in Table I. The remainder of this paper describes the procedures in more detail. In general, the process con-

Jan 1, 1956

By Warren Blauvelt

IN VIEW of the enormous wastes of natural resources, of labor and of capital, due primarily to the economic environment, established by legislation, the general neglect of this phase of the problem of the elimination of waste is difficult to understand. In such a study, the engineering method of attacking a problem should be employed. The engineer does not try to solve his problem by disregarding natural laws, but by utilizing them. The successful engineer establishes an environ-ment in which forces, acting in harmony with natural laws upon an object or objects, will produce the desired results. The engineer who notices that the water level in a vessel, into which a gallon of water per minute is flowing, is two feet higher than the level in an adjacent vessel, connected therewith by a 6-in. pipe, does not assume that the law of gravity has ceased to work, or that water no longer seeks its level; he examines the connecting pipe for obstacles which prevent the free flow of water. Some editors, many reformers and most politicians tell us that the law of supply and demand no longer works; hence governmental control of commerce is necessary. Governmental control may temporarily-that is, until trial proves its futility- "insure domestic tranquility" and "promote the general welfare;" but it cannot "secure the blessings of liberty" which it cur-tails, nor can it "establish justice" which it violates.

Jan 9, 1922

By S. S. Deshmukh

An important element of evaluating a materials- handling system by simulation lies in being able to examine the details of the proposed operation in a fashion which closely approximates real behavior. The added factor of flexibility permits including or deleting those parts of the problem which can be shown to be important or trivial. Used carefully, simulation can match manpower and equipment far more efficiently than conventional calculations. The same is true of interacting equipment systems. This efficiency results from being able to simulate the real fluctuations in a system by using empirical probability distributions compiled from existing operations. Simulation eliminates guessing as to efficiency, absenteeism, bunching, and the broad host of delays that influence productivity and substitutes operating data in place of the usual factors. In this respect, simulation improves detail and confidence in the reliability of engineering estimates.

Jan 1, 1970

By Samuel G. Lasky

FAULTING at Kennecott, with its attendant fracturing, is unusual, complex, and important. As study and knowledge of the various fault systems have progressed, appreciation of that importance has helped in the selection of proper horizons for exploration and in the avoidance of useless crosscutting and drifting. During the study of this faulting and fracturing, a suggestion concerning the formation of the ore-bearing fissures occurred to me. Further study in the available portions of the approximately 45 miles of workings in the Kennecott mines for the purpose of checking up the the suggestion led to the hypothesis which this paper will attempt to present. Briefly, the hypothesis may be stated as follows: The formation of transverse faults that stop against a main system is connected with changes in the strike or dip of the main fault, and such cross faults or fractures lie in the moving block of the main fault system and indicate a change in strike or dip of the main fault. It has been found that each kind of change tends to produce definite effects and that careful study of the evidence can often suggest the exact type of change. Outline of Kennecott Mines Geology The mines at Kennecott are on the northeast flank of a broad anticlinell where erosion has exposed the Upper Triassic Chitistone limestone resting conformably on the Permian or Triassic Nikolai greenstone.2 These two are the only formations exposed in the immediate vicinity of the mines that bear relation to the ore deposits. The Nikolai greenstone is a series of altered basaltic lava flows, the actual thickness of which is unknown. The Chitistone limestone is the ore-bearing formation. At its base is a bed of about 5 ft. of red, green, or black shale which shows strong evidence of movement wherever it is exposed underground—one of the

Jan 1, 1929

By Strathmore R. B. Cooke, Robert E. Brandt

EARLIER work1,2 has shown that the strength developed by fired magnetite pellets containing silica or silicates is due to three separate effects. Two of these are associated with the formation of slag in the interior of each pellet at temperatures above 1000°C, where the atmosphere is substantially though temporarily neutral. The third is independent of the silica content and is responsible for the development of a hard shell around the pellet during the initial stages of firing, a condition which permits the pellet to assume the increasing load of the overlying burden and prevents extrusion of the slagged and semi-liquid interior. Pellets made from hematite concentrates do not show these effects unless specific additives are incorporated, and it is these differences in behavior which in large part account for the difficulty in producing satisfactory pellets from such concentrates. Elsewhere it has been stated that "the most important factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of magnetite to hematite and the subsequent recrystallization and grain growth of this constituent."1 The object of the investigation reported in the present paper was to study in detail the mechanism described above and to evaluate its contribution to the strength of the fired pellet compared with other possible mechanisms, excluding slag bonding. This was effected by placing together polished faces of two cubes prepared from specific minerals and then heating them under constant pressure at different temperatures both in air and in nitrogen.

Jan 4, 1954

Jan 1, 1905

By John J. Porter

The requirements of the standard specifications under which Portland cement is sold have materially increased within the past 10 years, but practically all companies are now furnishing cement better than these requirements; in some cases exceeding them by nearly 100 per cent. From a sales standpoint, it is desirable to have a product that is uniform to a high degree and free from occasional quality troubles. A failure in quality, even if it affects only a few hundred barrels out of a yearly output of a million or more, is apt to be talked about in the trade and to affect the salability of the entire output. For these reasons, there has recently been great activity along the lines of quality control and improvement; and some of the most interesting problems of the industry are in this field. From the manufacturing standpoint, the quality of cement is chiefly a matter of uniform and proper chemical composition of the raw mix fed to the kilns plus proper burning in the kilns; the fineness to which the cement is ground, the proportions of gypsum, the method of seasoning, and the like are contributory factors. Uniform chemical composition of the raw mix has been one of the most difficult problems to solve. Most plants will use from 1000 to 3000 tons of rock per day and in but few cases is this material as it lies in the quarry even approximately uniform in composition. The problem, then, is to quarry and mix this raw material in such a manner that every handful passing through the kilns will have practically the same analysis as every other handful. To accomplish this purpose there are two methods of preparation: the wet and the dry. In each process, a stone storage is the first requisite of a successful plant. This storage place may handle the stone before or after crushing; its capacity may vary from two to three days' up to several months' supply, but it should be so designed that it can be filled as desired by the chemist and drawn at such points as will give a mixture of the various kinds of stone coming from the quarry and a reasonably uniform material going to the mill. The size of the storage place and the method of handling should be varied according to the nature of the material.

Jan 1, 1925

By Robert Craig, Earl L. Rau

Introduction Grinding circuits are used to reduce the particle size of ores to the size desired for beneficiation or to grind a concentrate to a size required for final marketing. Grinding and classification can be carried out using either wet or dry circuits. Most sulfide ores are ground in wet circuits using one or more stages of grinding to obtain the necessary mineral liberation to produce a final concentrate which will meet the desired criteria. Iron ores are ground in circuits applicable to the particular ore using either wet or dry grinding. Nonmetallic minerals frequently present different requirements. Barite is likely to be subjected to wet grinding before beneficiating the ore; the concentrate is dried and then dry ground to meet market particle size requirements. The one thing that most mill operators will agree to is that there is no such thing as the "best" configuration of equipment for grinding. The circuit which works well on one ore may be totally unsatisfactory for another ore body. The general trend in the industry is flow sheet simplication with fewer parallel circuits instead of multiple-line circuits using small mills. This change in philosophy has been brought about by the saving of both capital and operating costs that may be possible with larger equipment. Remember that comminution is basically a very inefficient process, and that the costs can range upwards to 50% of the total milling costs. It, therefore, behooves the mill operator to carefully design his grinding and classification circuits. He must ascertain the optimal economic particle size for beneficiation and then make certain he has achieved the best balance between capital and operating costs to achieve the desired mesh of grind. Equipment Grinding circuits consist of one or more pieces of equipment to grind the solids. Generally, these circuits include one or more grinding mills, classification equipment, and the necessary materials handling equipment such as pumps, pipelines, and conveyors. There are many different types of equipment available which are used to grind and classify ores and minerals. Following is a tabulation of most of the equipment used for wet and/or dry grinding.

Jan 1, 1982

By Lawrence Burkhart, S. B. Joo

A hemispherical, constant volume drop with forced internal circulation was considered as a model approximating a real drop at a similar stage of formation Axially symmetric steady flow within a drop contaminated by surfactants was described by solving the full Navier-Stokes equations written in terms of a meridian plane stream function Rotational flow occurred inside the drop above a computed Reynolds number of 5.8, and the change in interfacial flow caused by imposing a surface-tension gradient at the surface had a significant effect on the internal flow Although the work is quite fundamental in nature, the rotational flow described in the paper is responsible for much of the bulk transport of solute to the interface in hydrometallurgical processes such as solvent extraction.

Jan 1, 1981

W. ROWLAND Cox,* New York, N. Y. (written discussion?).-The process described by Mr. Malcolmson undoubtedly represents a great stride toward conservation of our natural resources. Without discussing the subject from an economic standpoint, I wish further to emphasize the fundamental principles of the Smith process in order that its economic value may be fully appreciated. The process is essentially a means of producing an ideal fuel, as regards its combustion qualities, by the removal of the so-called volatile matter from the coal, in the form of byproducts, which have value for other purposes far in excess of their fuel value. In other words, coals which contain. large amounts of gas, tar, and ammonia, and are not suitable for domestic or industrial fuel, or for treatment in byproduct coke ovens or gas retorts; because they possess poor coking qualities, can he prepared for commercial use by the. Smith process with a very high degree of efficiency. Much work has been done along this line, both in this country and in Europe, in developing a means of preparing coal, as the economic advantages have long been recognized. To the best of my knowledge, the Smith process is the only one that has proved its commercial adaptability. Distillation of coal at 900° to 1000° F. (480° to 540° C.) yields a large amount of tar and oils. The residue of the distillation, however, is a very friable semi-coke, wholly unsuitable for use as a fuel, unless it can be charged directly into a byproduct gas producer. The problem which confronted the inventor was then to convert this carbon residue into a commercial product, and it is in this step that the Smith process has overcome the obstacles which prevented a number of other methods from becoming commercially practicable.

Jan 10, 1918

By Edward A. Vitunac

The emerging importance of pneumatic conveying systems for bulk materials is largely due to the economic advantages such systems frequently exhibit when compared to alternate methods. Included in these advantages are relative simplicity, ease of installation, flexibility, ease of maintenance, cleanliness, safety and ease of automation to the degree desired. In general, installed costs favor a pneumatic system when compared to competing mechanical systems if the transporting distances are long or to and from many points. In addition, supplemental use such as cooling, heating, or drying may supply the incremental value required to justify its selection.1 The main disadvantages of a pneumatic system are the greater horsepower required per unit weight of material conveyed, material limits in abrasiveness, and density. In addition, material breakage tends to increase at changes of direction and at any obstruction such as that caused by the imperfect butting of two pipe sections in the conveying line. Classification of the material at the discharge may also cause problems in dusting and segregation. Materials weighing less than 4 lb per cu ft tend to cause feeding and collecting problems although they can be conveyed easily. Material between 4 lb and 20 lb per cu ft can be handled with fewer problems, but flow rate is hard to predict. The 20-60 lb per cu ft range offers best results, whereas materials of over 60 Ib per cu ft tend to drop out of the air stream and settle in the pipeline unless careful pro- visions are made to prevent this.2

Jan 5, 1968

By W. R. Bendy

GRINDING is a large and costly part of Portland cement manufacture. Prior to clinkering in the rotary kiln, raw materials are ground to a fineness of 80 to 90 pct passing 200 mesh. Then, after burning and cooling, the resulting clinker is ground to about 92 pct passing 325 mesh. In the cement industry the most favored method of grinding has always been by impact and attrition of a ball charge in a rotating mill. Other types of mills, in which materials are ground between die rings and rollers, or between die rings and large balls, are sometimes used for single-stage grinding and often for preliminary grinding followed by grinding in ball-type mills. Their efficiency is usually high, but maintenance and repair costs are high also, and the ball-type mill continues to be the most widely used.

Jan 10, 1957