Search Documents

By J. Ruben Velasco, Roland B. Mulchay

CANANEA has long been recognized as a remarkable field for geologic study. The copper deposits and rocks of the district have been described by many geologists and engineers, but only the most general correlations have been made between Cananea sedimentary rocks and other known sedimentary sections in the southwestern United States and northern Mexico. The present paper describes the Cananea sediments in greater detail than has been done before and attempts to fit the Cananea sedimentary section more closely into the geologic time table. The lack of well-preserved fossils has made it difficult to date the sediments accurately in geo- logic time, but it is possible to make tentative correlations between the Cananea sediments and the southeastern Arizona sections, based largely upon lithology and general position in the geologic column. It appears that sedimentation at Cananea and Bisbee may have been closely similar during Paleozoic time. Even such generalized correlations, however, may be subject to considerable modification in the future. The present study has led to the recognition of other problems of age and mineralization relationships in the Cananea district. Cananea is located in the north-central part of the state of Sonora, Mexico, at an elevation of 5270 ft. It is about 135 miles northeast of Hermosillo, the state capital, and 25 miles south of the international boundary. By road Cananea is 40 miles from the twin towns of Naco, Ariz., and Naco, Sonora, and about 50 miles from Bisbee, Ariz. It is served by the Nogales-Naco branch of the railroad, F.C. Pacifico, and is connected with Chihuahua and Mexico City by the Aeronaves airline.

Jan 6, 1954

By H. W. Fox, M. R. Achter

IN a previous study of the effect of atmosphere on creep-rupture properties,' it was shown that the relative strength of nickel in air and in vacuum may be reversed by a change in either stress or temperature, Fig. 1. At low stresses and high temperatures the metal is stronger in air but stronger in vacuum at high stresses and low temperatures. A mechanism to explain this reversal was proposed involving two competing processes; oxidation strengthens the metal while adsorption of gas lowers the surface energy, relative to that in vacuum, and reduces the work required to propagate a crack. The process which controls is determined by stress and temperature. In a number of private communications, however, the objection has been made that even in the vacuum of objection mm of Hg used in this study, the surface of a

Jan 1, 1960

By W. W. Scott

The application of engineering methods to the problems connected with drilling and producing in the oil industry has led to the development of the science that is variously termed "petroleum engineering," "production engineering," "petroleum production engineering," and even Itpolitical engineering." It would require much detail to enumerate the qualifications of a petroleum engineer, just as it would for an engineer in any major industry. For those who have a genuine liking for the oil industry, there is a wide selection of pathways to achievement. The oil industry is now highly specialized. Its products are necessary to all civilized people and are indispensable in the security of our nation and also in the well-being of our families. The business structure of our country depends in a large measure upon oil, and the welfare of this group as individuals is certainly linked with the welfare of the oil industry. What Is the Trend of Engineering? The oil industry offers a fertile field of opportunity for engineering; probably more so than any other industry. The sciences of geology, physics, chemistry and mathematics are all used in some phase of the oil industry and to a very considerable extent in the production division, which embraces the geological, drilling and producing departments. In drilling and production alone, research programs of considerable magnitude are being carried on at this time, and no doubt the future will see a great deal more of this kind of work. Through the cooperation of the engineer, the equipment manufacturer, and the American Petroleum Institute, immense savings have been made by the standardization of drilling and production equipment. Drilling equipment in itself offers a wide scope for study, in that continued efforts are being made to improve the equipment so that it can be made to drill faster and to greater depths. The improvements in drilling equipment are required because new reserves of oil are being found at progressively greater depths. In order to produce such oil in competition with oil now being produced from reservoirs

Jan 1, 1937

By E. W. Davis

The mixing of fine ores with fuel and burning under induced draft is called sintering in iron-ore practice and either sintering or roasting in copper and lead metallurgy. The first development of sintering was the Huntington-Heberlein process, in which fine sulfide ores mixed with fuel were charged into a pot and burned under the action of an upcast current of air introduced at the bottom of the pot. Modern development has resulted in two types of machine; the continuous Dwight-Lloyd machine, which consists of heat-resisting grates and a moving beltlike type of hearth constructed of metal, in which air is drawn downward through the bed, and the stationary Greenawalt batch process, which operates in the same manner as the Dwight-Lloyd except that the hearth is stationary. The recent rapid increase in the use of sintering has been the result of two great advances in metallurgical process—flotation and the treatment of flue dust. The Dwight-Lloyd machine is used in many plants for agglomerating flotation concentrates and at the same time reducing the sulfur content to furnace requirements and it has become standard practice to treat iron blast-furnace flue dust by either the Greenawalt or Dwight-Lloyd machine, so that it can be recharged into the furnace. The mining of low-grade magnetite iron deposits and their beneficiat-ing by grinding and magnetic separation resulted in a fine concentrate extremely detrimental to blast-furnace practice. These concentrates are sintered and made into ideal material for blast-furnace use. Incidentally, coke savings of about 400 lb. per ton of pig are reported. Sintering at Evergreen Plant The application to limonitic iron ores is the most recent development of the sintering process. The first plant in the Lake Superior region was erected by the Minnesota Sintering Co., a subsidiary of the Evergreen Mining Co., at Ironton, Minn., in 1924. This plant was designed to treat Cuyuna Range iron and manganiferous ores containing low silica, high moisture and a structure objectionable because of a large proportion

Jan 1, 1930

By Charles Albert Ashburner

THE stratigraphical geology of the vicinity of Buffalo has always been of great interest on account of its bearing on the origin and history of the Niagara-river gorge, between the Falls and Lake Ontario. Recently, however, the character and thickness of the strata which underlie Buffalo have acquired more practical and economic importance on account of their relation to the possible occurrence of natural gas in commercial quantity near the Niagara river. In a paper presented at the Duluth meeting (l887), on " Petroleum and Natural Gas in New york State" (Trans., xvi., 906), I gave a brief description of the four wells which had been drilled by the Buffalo Cement Company between 1883 and that time. One of these wells is 1305 fret deep; and, at the time that my paper was finally revised for the Transactions (June, 1888), it was still an open question whether the drill in this well had reached the Niagara limestone, or had penetrated the Medina sandstones and shales, which latter are boldly exposed in a number of localities in the district, hut more particularly along the Niagara river in the vicinity of Lewiston and Qneenstown. The difficulty in this geological question at Buffalo has lain in the fact that no reliable determination could be made of the thickness of the strata included between the Corniferous limestone, immediately below which the drilling of the Buffalo gas-wells was commenced, and the Niagara limestone. On the other hand, the strata included between the latter limestone and the middle portion of the Medina sandstones and shales, have been minutely measured and studied in the Niagara gorge below the Falls by many American and European geologists. The first reliable section of these strata was constructed by Professor Eaton, and published in 1824 in his report on the Geological and Agricultural Survey of the District adjoining the Erie Canal. This section, extending from Lake Erie to Lewiston, is complete, with the exception that no thickness is given to the Salina or Onoudaga salt group,

Jan 1, 1889

By Charles S. Larkey

Numerous papers have been published on the use of graphic methods for determining the best curve for estimating the production decline of oil wells but, as far as the writer has been able to ascertain, nothing has been published showing how curves may be worked out mathematically that will conform most closely to the production data under consideration in any given instance; hence the writer has endeavored to show just how such application can be made. Among the valuation engineers, two types of curves are in current use for the representation of the decline in production of oil wells. One may be represented by the equation, y = krx; this is sometimes known as a percentage curve, for the production for any period is multiplied by a constant rate or percentage to obtain the production for the succeeding period. It appears as a straight line on semilogarithmic cross-section paper. The other curve may be represented by the equation, y = kxn, and is shown as a straight line on logarithmic cross-section paper. In each equation, y represents the number of barrels produced in a given period of time, and x the successive periods of time. The other letters are constants to be determined for each well, or group of wells considered in arriving at the most probable curve to represent the rate of production for a given property. From this the underground reserves may be estimated by extrapolation, or by extending the curve beyond the last known period of production to show the most probable production values for the future. Application to the Burbank Pool Fig. 1 relates to a property in the Burbank Pool, Osage County, Okla. The production is shown as an average per well per month, is plotted to the vertical scale of barrels on the left-hand margin and to the horizontal scale of months at the bottom of the chart. In column y, the number of barrels is listed beginning with May, 1922, as the first month on which to base a decline curve. The type of curve used is of the form, y = krx, or, expressed in logarithms, log y = log k + x log r, in which log k and log r are constants to be determined so that the curve will most closely approximate the production data given.

Jan 1, 1925

By D. J. Blickwede

WHEN iron is dipped in molten zinc at temperatures in the range 840" to 930°F, the two metals react to form layers of Fe-Zn compounds which adhere to the iron. At the galvanizing tem- perature, the successive layers are:' y (Fe5Zn21), 61 (FeZn;), and 5 (FeZn13), in conformity with the Fe-Zn constitution diagram. There is no quantitative information in the literature on the rates of growth of the individual alloy layers over the temperature range 840° to 930°F. Rather all the past experiments have studied the loss in weight of iron as a function of galvanizing

Jan 1, 1954

By Raymond B. Ladoo, C. A. Stokes

This paper summarizes the economic problems of the industrial mineral industries which are essentially different from those of the metals and the fuels. Failure to understand and evaluate such factors as markets, place value, and substitutions of one mineral for another may be disastrous. The engineer should be as responsible for profitable operation as he is for technical efficiency. The Raw Materials Survey of Portland, Oregon, is described.

Jan 2, 1950

Jan 1, 1902

By R. M. Stewart

INTRODUCTION Requirements for achieving economic slope stability in open pit mining must not only be met during the operating stages but in all preceding stages of mine development. In many operating mines little or no emphasis was ever placed on evaluating the stability of possible slopes during the exploration and planning stages. The purpose of this discussion is to emphasize the necessary considerations that should be made in all stages of development in order to achieve the safest and most economic pit slopes. The most economic slopes may not always be the safest slopes and it is incumbent upon the mine operators and engineers to achieve an optimal combination of economics and safety. The stability requirements outlined are based on the profit motive and are, therefore, practically oriented. Long-term basic research or theoretical studies are considered important only to the extent that they can be shown to have a definite payoff. Consideration will first be given to the information required for stability analysis, which can be determined during the exploration and evaluation stage, followed by further stability work necessary during the mine planning and layout stage. Particular emphasis is then placed on the operating stage in which blasting, dewatering, artificial stabilization, and slope failure are discussed. Lastly, the importance of a logical and orderly research procedure is stressed. EXPLORATION AND EVALUATION STAGE The purpose of the exploration and evaluation stage in the mining scheme is to find and delineate a potential orebody. Discovery and delineation commonly involve drilling tens and in many cases hundreds of boreholes. These boreholes, which may cost as much as $20.00 per foot of depth for a cored hole, are usually abandoned once drilling is completed. Stability evaluation for a potential open pit should begin at this stage by taking advantage of the existing boreholes. Rock and soil properties, as well as hydrologic parameters, may be obtained from both the borehole and the core. Seismic velocity and neutron probes may be used to log the borehole to obtain elastic moduli data. A borehole dilation jack may also be used to give backup information on the rock and soil elastic parameters. Use of a core orientation system can result in the determination of fault and joint frequency and distribution. Before splitting or otherwise disturbing the fresh core, qualitative evaluation

Jan 1, 1972

Operating Characteristics of Centrifugal Fans and Use of Fan Performance Curve Discussion of paper by. Louis W. HUBER, presented at the New York Meeting, 1926, .and issued, as Pamphlet No. 1542-A, with MINING AND METALLURGY, February, 1926. G. BRIGHT, Pittsburgh, Pa.-Apparently from the pressure curves for a forward-curved-blade fan, in Mr. Huber's paper, practically all ventilation-might be stopped with increased resistance. In order, to discuss the characteristics of a fan we need, some better way to measure the characteristics of a mine. You all know that. the average anemometer is not very-reliable. Sometimes two anemometers, supposed to be recently calibrated, will differ 50 per cent. Either this or some other committee should standardize measuring methods. The characteristic curves of fans, given by Mr. Huber, would indicate that the forward-curved-blade fan would cause trouble in attempting parallel operation, because two machines will not parallel unless they have dropping pressure characteristics. On the other hand, it is indicated that with the backward-curved blade, they could easily be paralleled. But few mines use more than one fan. Mr. Huber said that if the resistance of the mine was considerably more than contemplated, the quantity of air might be such that the efficiency of the backward-curved fan would be seriously affected, dropping say from 70 to 55 or 50 per cent. In such event, could a difference of speed be selected for the fan that would give the quantity desired at a higher efficiency? L. W. HUBER, Pittsburgh, Pa.-The backward-curved-blade fan responds to change in speed the same as any other fan; if' the speed is doubled, the quantity of air is doubled, the pressure is increased four times and the horsepower eight times. One point not mentioned in the paper is that the backward-curved fan is more efficient than the forward-curved or any other type. If the latter were more efficient, it would pay to install that type and keep the resistance of the mine constant, which is hard to do but it can be done with care. But the total mechanical efficiency of a fan with backward-curved blades is from 10 to 20 per cent. higher.

Jan 1, 1927

By R. D. MacDonald

The search for metalliferrous deposits in the Labrador-Ungava Trough of Canada dates from 1929 when non-ferrous minerals were the main quest of prospectors in this area. Many gossans, resulting from the oxidation of sulfides, were located and examined but none of these led to any orebodies of commercial value. However, such investigations did much to arouse interest in this area and fostered further mapping and prospecting. Since this early period in the history of prospecting in the Trough, the presence of iron ore deposits and potential iron producing sites has commanded the center of attention of exploration personnel. The iron-bearing rocks of southwestern Labrador have in recent years come into prominence as possible sources of iron ore of the beneficiation type. Exploration and development work has been carried on in concession areas granted by the Newfoundland Government to the Labrador Mining and Exploration Co. Ltd. and to the Newfoundland and Labrador Corp. In the course of evaluating its holdings in the Wabush Lake area (Fig. l), Labrador Mining and Exploration Co. has conducted geological, geophysical and diamond drilling programs.

Jan 10, 1960

By A. Springer

Chemists, physicists and others, whose occupations necessitate the use of fine scales, have heretofore regretted their inability to obtain any which would remain uniformly accurate. The difference between the theoretical and the actual results obtained in the ordinary balance (provided the pivot-distances are exact) is mainly due to the frictional resistance between the knifeedges and their bearings. This frictional resistance, although reduced to a minimum in the finest scales when new, constantly increases, thereby decreasing the sensitiveness proportionately. When examined under the microscope, neither the surface of the knife-edge nor that of' its hearings ever appears perfectly smooth. Soft kunife-edges are easily blunted, whereas hard ones are brittle and liable to crumble under the effects of over-load or shock. Prof. Frederick A. Roeder for many years attempted to discover some means by ,which the knife-edge could be replaced with some device free from the above-mentioned objections. His experiments convinced him that a torsion-joint was best suited for that purpose. After he had communicated his conclusion to me, we jointly developed the system to its present form. A torsion-wire had been used for the centre of rotation, prior to Prof. Roeder's invention, but it was found impossible to replace the terminal knife-edges with torsion-joints.

Jan 1, 1884

By Clamer, G. H.

G. H. CLAMER, * PHILADELPHIA, PA.-Unfortunately, prior to the war no serious attention was given to the conservation of tin, notwithstanding that this country is practically dependent upon outside sources for its entire tin supply. Tin is of vital importance in many industries, but it is surprising how many and how excellent are its substitutes when we become acquainted with them. Tin has always been a relatively high-priced metal, and it is part of the human attitude to associate high prices with high standards; it is not until the price of a commodity becomes well-nigh prohibitive that we hunt for substitutes, because the idea of substitution seems always to involve an assumption that the substitute must necessarily be inferior. The history of the development of bearing bronzes is a striking example of this policy. In the early clays, copper-tin alloys were almost universally used, the idea then being prevalent, which is still held by many, that a bearing to resist wear must be hard, and the harder the better. The favorite bronze bearing contained 90 per cent. copper and 10 per cent. tin; frequently, in service which was considered severe, even higher proportions of tin were used.. Such hard alloys have great resistance to compression, but as a rule they had a very wide factor of safety in this

Jan 12, 1918

By John Birkinbine

In the spring of 1878 the Pine Grove Furnace, located in Cumberland County, Pa., was blown in after lying idle for several years. The fnrnace was constructed in 1770, and for over a century it has been in almost continual operation. The plant consisted in 1877, when the writer was first called there, of a stone stack 32 feet in height, inclosing a shaft and boshes, the latter being 8 feet in diameter. The blast was supplid by two wooden blowing-tubs discharging into a third, having a floating piston sustaining a box weighted to give the desired pressure, the power being furnished by a waterwheel. A small 18-pipe hot-blast stove heated the blast. The furnace was remodelled during the winter of'77-78, and a Weimer blowing-engine with a blowing-tub 5 feet in diameter and 2 feet stroke, and the necessary boilers, were substituted for the wooden tubs and water-wheel. The stack was raised and enlarged, and provided with a bell and hopper having a central drop. Water dam and tymp were added, and general repairs were made. The hot oven, however, was not increased. The furnace had always been operated with charcoal as fuel, and its reconstruction was made with a view to continue the use of charcoal, but provision was made for ample blowing capacity should other fuels at any time be employed. Although liberal arrangements had been made in cutting wood, the stock of charcoal supplied in 1878 was insufficient for the increased requirements of the remodelled plant, and notwithstanding the purchase of some 80,000 bushels from an adjacent idle furnace, there war: riot enough to keep the furnace in constant blast until a new supply could be obtained, particularly as the season was unusually backward. Instead of following the established precedent of many charcoal furnace managers, i. e., blow out every February, it was detemined to continue in blast, using coke as fuel. Accordingly, when the charcoal stock was exhansted, on March 22d, 1879, Connellsville coke was substituted, the change of fuel being made at once; that is, the coke charges followed immediately upon the last charcoal charges. After working a few days, the strike in the Connellsville coke region cut of the supply, and anthracite coal was obtained, a mixture of the two fuels being employed. The strike continuing,

Jan 1, 1880

By R. W. Raymond

The death of Professor Blake removes the oldest of American economic geologists and mining engineers, and deprives this Institute of one of its earliest and most illustrious members. To many of us it brings a personal loss also, the loss of a friend. William Phipps Blake was born June 21, 1826, in New York City. His father, Elihu Blake, was a surgeon-dentist of eminence, a direct descendant of William -Blake, who settled in the Massachusetts Bay Colony about 1630. He was prs pared for college at private schools in New York, and entered the Sheffield School of Yale, where he was graduated as Ph.B. in the chemical course, class of 1852, the first graduating-class of the institution. In the same year he became chemist and mineralogist of the New Jersey Zinc Co., and chemist of chemical works at Baltimore, Md. In 1853, he started the Department of Mineralogy of the World's Fair at New York City. In 1854, 1855 and 1856, he was mineralogist and geologist of the United States Pacific Railroad Surveys of Willianlson, Pope, and Whipple, and for the War Department at

Jan 1, 1911

By D. L. Ward

This paper is the result of a study, in 1919, to determine how much surplus power could be produced through the proper utilization of the entire gas flow from the two furnace stacks at the Federal Furnace Plant, South Chicago, Ill. Obviously, the problem was to measure the flow of gas through the main beyond the point where the amount necessary for stove operation was removed. In all probability, blast-furnace gas is the most difficult gas to measure, because of the high moisture and dust content, and the widely fluctuating flow from the furnaces. This wide fluctuation of flow forbids the acceptance of any one group of flow readings as indicative of normal operating conditions. A study of the conditions showed that a recording device on gas flow was necessary. As the gas at the point of measurement had passed through wet washers, and accordingly was saturated with water and contained considerable dust carried past the scrubbers in the form of sludge, no form of Pitot tube could be used, for this sludge would quickly plug the dynamic and static holes, spoiling the gage readings. An even more serious objection to the use of Pitot tubes was the impossibility of accurately measuring the cross-sectional area of the gas main on the plane of Pitot-tube installation. Given an absolutely clean gas and a perfectly circular pipe, it would be safe to assume, through measurements of the pipe diameter, that the gas main was of a certain cross-sectional area. But the continual depositing of sludge and the fact that the main was fabricated from riveted sheets led us to discard the idea of using Pitot tubes for this service. The Venturi tube was then considered, and had there been a sufficiently long straight run of gas main to accommodate a tube of the required size (72 by 28 in.) such an installation would very likely have been made.

Jan 2, 1921

By A. J. Lyon

THE stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening; which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging-heating in a temperature range below 170° C. (340° F.)-will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1928

By Ernest Wiltsee

The Half-Moon mine, situated three miles west of the town of Pioche, exhibits geological features which are peculiar and interesting. The general formation in the vicinity of Pioche consists of a quartzite, usually covered with an overlying limestone containing strata of shale. In the camp itself, where the original mines are situated, the quartzite has been denuded, and the principal veins outcrop in this formation; to the west, the quartzite is again covered with limestone, containing thin strata of shale.

Jan 1, 1893

By N. Lilienberg

During the past fen- years, the requirements for steel have been raised so high that soundness is more important than ever before. The old practice mas to make steel ingots of suffciently large sections to permit a considerable reduction of area in rolling and hammering to a given size, relying on the fact that by such rolling and hammering all cavities will be squeezed together and practically eliminated. The finished sizes, if found by inspection of the surface to be faultless, were therefore pronounced to be sound. But when such steel is " worked up," the manufacturer is surprised and disappointed to find that it splits, or that streaks and seams make the product unmarketable. Large sections, such as rails, beams or heavy forgings, may, within certain limits, be sufficiently strong, even if the sides of the cavities are only squeezed, and not welded, together. But it is well known that, in the interior of heavy articles, under certain conditions, forging may develop small streaks into large cavities. Small sections, steel for ordnauce and tubes, and numberless articles in the tool-trade, always show up the defects. It may be doubted whether cavities in steel ingots can ever be completely welded. The old theory is, that the silver-clear blow-holes, without the blue oxide, can be welded by suffcient working. They are, however, not empty, but are filled with carbonic oxide. It is admitted that the " blue " cavities, resulting from air mechanically drawn down into the mold during the casting, can never be welded, because the oxide does not melt, and there would be no escape for it if it did. The only way in which steel can be made satisfactory for the above-named particular purposes is by having it " dead molten." But then the trouble of piping is encountered. As is well known, a pipe is the result of the contraction of the liquid interior after the surface of the ingot has become solid by contact with the mold. When this contraction is partly

Jan 1, 1907