Search Documents

By E. S. Wheeler

The conversion plant of the Clirnax Molybdenum Co. is at Langeloth, Washington . County, Pennsylvania, approximately 30 miles west of Pittsburgh. The molybdenite concentrates converted originate in the company's mine and mill at Climax, Co1orado.l They are delivered to the Langeloth plant by rail packed in 175-lb. bags. War production of concentrates at the mill started in 1918 but it was not until about 1920 that any peacetime uses of the metal began to develop. Early conversion of Climax concentrates was mainly into ferromolybden um, produced for the company by a custom smelter. Chronology of Plant Development In 1924 a small hand-rabbled roaster was built at Langeloth, the roasted concentrates being used principally in the production of calcium molybdate by a conventional wet method. The size of the original plant is indicated by the fact that during 1925 about 400,000 lb. of molybdenum was converted. In 1925-1926, a multiple-hearth roaster was erected (12-ft. 0.d. 8-hearth Nichols-Herreshoff); also the first experimental ferromolybdenum was produced at Langeloth. At this time sa.1cium molybdate was produced in the furnace by a process to be described. With continued interest in and increased use of molybdenum, it was necessary to arrange for enlargement of plant facilities. Although only one 12-hearth 16-ft. 0.d. roaster was erected at this time (1929), plans were prepared for a duplicate unit, which was completed in 193 5, giving a potential roasting capacity of some 16,000 lb. Mo per day under the then prevailing roasting practice. Shortly after this second unit had gone into production, increased demand overtaxed the plant, and as a result two 12-hearth 18-ft. 0.d. roasters were placed in operation in 1936 and 1937. This gave the plant a potential roasting capacity of 40,000 to 50,000 lb. Mo per day, and necessitated major changes in auxiliary handling equipment as well as improved facilities for producing ferromolybdenum. Following the introduction (1938) of a new product—molybdic oxide briquets— and because of the constantly growing demand for molybdenum, plant facilities were again enlarged in 1940 and 1941 by the erection of two 16-hearth 18-ft. 0.d. roasters. These two new units, along with a change in roasting practice, brought the potential roasting capacity to 150,ooo to 190,000 Ib. Mo per day, based on about 15 lb. per sq. ft. of hearth area. Other departments of the plant have necessarily grown, until today the plant is modern throughout and completely mechanized, with equipment geared to produce marketable products as follows:

Jan 1, 1944

By Richard Moldenke

One of the little-known characteristics of cast iron, which nevertheless has an important bearing on results where accuracy in machining is essential, is the ability of this material to ease up internal strains when allowed to remain quiescent for a more or less extended period of time. It seems as if the molecules in such a casting, by virtueof their "mobility," can adjust their relative positions to an extent sufficient to overcome some of the existing stresses. The following instance will perhaps give a fair idea of the condition a casting may be in when just shaken out of the sand. A very large sheave-wheel, after shaking out, was taken outdoors to be cleaned and made ready for turning up. It was leaned against the side of the building, but before much could be done an arm tore apart with a loud report. Investigation showed that the sun had been shining on the upper rim, thus adding a slight strain to those already existing within the arm and thus overbalancing the strength of the metal in tension. Had this sheave been kept under cover for a while, or at least until machined, the strains would have eased off sufficiently to allow the sun to look upon it without disaster. It will not be necessary to multiply examples. Every engineer knows the danger of water-hammer in pipe lines, particularly if the latter are of cast iron. Every mechanic knows, or should know, that it is not good to strike a fitting that is under steam pressure. It will be necessary to say a few words on the "internal strains" in castings—the so-called "casting strains" we hear so much about. We all know that to get a casting reasonably true to the dimensions wanted requires a slightly larger pattern. The usual allowance for gray iron is 1/8 in. to the foot (1 cm. per meter) and 1/4 in. to the foot (2 cm. per meter) for white iron (all dimensions). This reduction in length, breadth and thickness in a casting is erroneously called "shrinkage." It should be called "contraction," as for practical purposes it is simply the difference in dimensions of the casting red-hot and cold. The real "shrinkage" covers an entirely different situation. When a

Jan 1, 1917

By N. S. Keith

No one of the live subjects of the day, to which the attention of the mining engineer and metallurgist should be turned, is of greater practical interest to him than electricity in its applications to various mechanical, chemical, and metallurgical operations. The object of this paper is to call the attention of my fellow-members and associates of the Institute to various new, as well as comparatively old, developments in the science and art of electricity which seem to promise results of advantage. Too many of the comparatively old applications have been neglected by the mining engineer, which; if he had given them a place among his appliances, would have assisted him greatly. The telegraph may be noticed as one. Its. use is, however, confined to a person having skill in the. manipulations of the key, the reading of the alphabet, and familiarity with the sounder. One of the simpler forms-the call-bell-has a range of application far greater as to distance and convenience than the old wire-pull, or the hoarse voice of the windlass-man or the bucket-dumper. A few Leclanehé cells, two or more electric bells, and a mile or more of wire judiciously placed will put the superintendent, at his office, in communication with the foremen of his mills and mines, so that by the aid of a code of signals, great advantages may be gained without necessitating a knowledge of the Morse alphabet, or of the mechanical voice of the sounder. The telephone furnishes a means of communication be-

Jan 1, 1882

By W. I. Duvall, D. E. Stephenson

A theoretical solution is given for the energy that is radiated outward when either a cylindrical or spherical cavity located underground in a uniform stress field is suddenly created or enlarged. The method of derivation shows that the stress field in the solid rock surrounding the opening does work on the rock because of elastic displacements that result when the size of the cavity is increased. The amount of this work is sufficient to account for both the increase in the strain energy in the rock surrounding the opening and the seismic energy that radiates outward. Thus, the source of the radiant seismic energy is mainly the gravitational potential energy and not the strain energy stored in the rock. The amount of the radiant seismic energy is directly proportional to the volume of the rock removed from the opening or relieved of stress. Seismic energies from rockbursts are compared with earthquake energies. Also, the amount of gravitational potential energy released by underground explosions is calculated and found to be small compared to the seismic energy generated by the detonation of the explosive. A review of the early literature on rockbursts shows that a number of investigators calculated the amount of energy released by rockbursts. 1-5 However, none of these papers give the formula used to make these calculations or a reference to the derivation of any formulas. The general impression that one obtains from these early papers is that the main source of the seismic energy released by rock-burst is the strain energy stored in the rock before it is fractured. However, a few of the early papers appear to have considered the solid rock at a distance from the mine opening as a possible source of the seismic energy. Recently Black and starfield7 gave a theoretical solution for the strain energy in a stressed plate with and without a circular hole. Also, Press and Archambeau8 gave the theoretical solution for the seismic energy released when a spherical cavity is created in rock subjected to a three-dimensional stress field. Both of the above theoretical papers start with the condition of no opening and calculate the strain energy before and after the opening is suddenly formed. Neither of these papers appear to have calculated the work done by the applied stress field as the cavity is enlarged. The rockburst problem associated with deep mining is concerned with the failure of the solid rock surrounding an underground opening. Therefore, it seems appropriate to consider theoretically the problem of suddenly enlarging the size of an existing opening. The purpose of this paper is to present the theoretical solution for the energy that is available for release as seismic energy when an underground circular tunnel or spherical cavity is suddenly enlarged in diameter. To keep the mathematics as simple as possible, a uniform radial applied stress field is assumed and the rock is assumed to be isotropic, homogeneous and perfectly elastic.

Jan 1, 1965

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By R. C. Palmer

THE testing of flotation oils has occupied a large part of the time of the testing departments of various companies using the flotation process in the beneficiation of their ores. The great differences in ores and iii oils has made such work necessary as it has not been possible to select the oil best suited for the purpose without trial of many kinds. In fact, individual shipments of flotation oils from the same manufacturer will often differ so radically that the mill men have been forced to test every lot of flotation oil before its use in the mills. Further, although almost every imaginable product of the distillation of wood, from alcohol to pitch, has been tested in a more or less perfunctory manner by various people, few companies have allowed the results of their tests to be made public. This work was undertaken for the purpose of obtaining reliable data regarding the value as flotation agents of a number of products that are obtained from the distillation of wood by different methods, and incidentally to determine whether some of the products not used at present could be used. Large quantities of such materials are being wasted or burned in the wood-distillation plants of the United States, and if some use other than fuel could be found for these materials, such a use would represent a distinct saving to the country as a whole, would increase the profit of wood-distilling plants now operating and perhaps make it possible for others to operate which at present cannot do so except at a loss. At the same time it was thought that if such products can be used as flotation agents, then their use would serve to increase the number of oils and other products available for flotation purposes. It was also hoped that it might be possible to discover a substitute for some of the most effective but comparatively high-priced oils which are now used for flotation

Jan 8, 1916

By W. O. Hotchkiss

DURING the summer of 1927, the Department of Terrestrial Magnetism of the Carnegie Institution of Washington joined with the Michigan College of Mining and Technology in conducting a series of earth-resistivity measurements in the Michigan copper country. The geological structure in this section is quite varied and fairly well known. The purpose of the investigation was to discover the correlation between the variations in electrical resistivity of large masses of soil and rock in place and the geological structure below the surface. The work done may be roughly divided into two parts: (1) Measurement and study of the variations in resistivity with depth, or with volume, to establish such general relations as exist between the two: and (2) the determination of the specific resistivity of various formations in order to make available more fundamental data which may aid in the interpretation of the results of the former type of measurement. A report by Mr. Rooney, which gives in detail the measurements made and the results obtained, forms the basis for this article. MEASUREMENT AND STUDY OF VARIATIONS IN RESISTIVITY The possibility of applying data from measurements of the physical properties of earth material to the 'study of the geological structure has long been recognized, and a number of methods for determining the position and character of concealed rock strata by means of seismic, gravitation, magnetic and electrical measurements made on the surface are being used with varying degrees of success. One physical property which varies widely for different materials, and hence affords an opportunity for distinguishing between them, is their electrical resistance. Locations were selected where the geological structures were well known and where the depths to the water level and bed rock had been determined by drilling. The problem was to determine the value of measurements of resistivity and its variations as indications of the geological structure below the surface.

Jan 1, 1928

By Galen H. Clevenger

Equipment for treating lead ores was added in 1905 to a copper plant which the United States Smelting Refining and Mining Co. had built in 1902 at Midvale, Utah, about 12 miles to the south of Salt Lake City. By 1906 the lead section of the plant had been rounded out and consisted of a 90-ton gravity concentrator, fifteen hand-rabbled reverbera-tory roasting furnaces, six blast furnaces, a briquetting plant for handling flue dust and fine ores, a regulus furnace for concentrating the low-grade matte made in the blast furnaces, and a baghouse. The copper section was later abandoned and the plant has been operated for many years exclusively as a lead smelter. Some 45 years had elapsed at the time this plant was built since the first attempts to smelt lead ores in the West, and lead smelting had become a large and profitable industry but fundamentally little that was really new had been developed, which could be embodied in a plant built in this period. Principles and tools to work with had remained much the same as those borrowed earlier from European practice. Capacities had been increased and there were mechanical improvements but hand charging was still in vogue and there was little attempt to recover suspended particles carried out with the furnace gases, beyond settling in flues, which usually was only partly effective for recovery of the coarser particles. Satisfactory roasting and preparation of the fine components of the charge were still partially solved problems. The Midvale plant of 1906 may be regarded as more or less typical of the smelting plant of this period for treating complex western lead ores as distinguished from the recovery of lead from the simple lead ores to the eastward. The operation of a concentrating mill directly in conjunction with a lead smelter was, however, not common practice. The ores treated in this plant have from the beginning come from mines owned and operated by the company or have been custom ores purchased in the territory tributary to the plant. The treatment of custom ores is an important service to the small producer who does not have sufficient tonnage to warrant a plant, and serves to increase the tonnage of the operator of large properties, thereby helping to reduce

Jan 1, 1937

By William Brewster

DATING back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus con-tent, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/16-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

By E. Wainer, K. D. Burnham

A wet beneficiation technique for producing wollas-tonite from its ore in high yield and purity has been evaluated in a pilot plant operation at the rate of 75 tons per month. Finely crushed, unsized wollastonite ore mixed with water is passed through a high in tensity oscillating wet magnetic separator of unique design and in a single pass over 90% of the wolla-stonite exhibiting a crystal purity of 99.8% is obtained irrespective of size of feed fraction. Thereafter, the material is processed by closed cycle standard wet milling and classification techniques to yield a 1µ size product, though any mesh size up to and including 50 mesh may be obtained, if desired. Costs appear to be significantly lower than those available from dry processed techniques. Wollas tonite made by this unusual wet process appears to have potential utility in the following fields: ceramics, paints, plastics, paper, organic finishes, reinforcement of portland cement items, controlled porosity refractory ceramic foams, cinder and concrete block paint, and the like. The 1µ and certain chemically processed varieties of wollastonite may have unusual utility in the paper industry both as a filler and as a coating material and in the organic finish industry. Extensive deposits of wollastonite ore equivalent to an average tenor of 50% to 60% of this latter mineral in easily separable form exists in and around Essex County in northern New York State in reserves of the order of several tens of millions of tons. While important portions of these deposits are susceptible to open pit mining techniques, one operation near Wills-boro, N.Y., involves tunnel mining and dry milling and beneficiation techniques. This mill and tunnel mine is presently being operated by The Cabot Corp. and a variety of particle sizes are now sold into markets in the ceramic, paint, plastic finish, floor tile and in similar fields in substantial tonnages on a repetitive basis. Serious investigation and study over the past several years has indicated that, outside of the obvious economies of open pit techniques for mining purposes, wet beneficiation and milling procedures applied to the ore not only represent a potential for greater economies in the production of a superfine finished product but yields products of improved properties exhibiting increased market potential which may not be available from the dry ground product. The Lewis and Deerhead deposits, controlled by the Adirondack Development Corp., appear to be identical to the Wilisboro deposit. Utilizing ore taken from the Lewis and Deerhead deposits, a pilot plant process for the wet beneficiation, milling and classifying of wollastonite ore has been operated for several months. After scalping a marketable garnet product from a minus 16 mesh dry crushed feed on a high intensity roll magnet the balance of the material is then roll crushed in a closed cycle until it will pass a 50 mesh screen. The product constitutes the feed of the wet magnetic separator. The heart of the new beneficiation process is a cyclically operated wet magnetic separator which exhibits the unique feature that unsized feed is easily handled. Product yields of higher purity are equal to that obtained with dry magnetic separations which use closely sized dry ore and multiple passes, but only produce wollastonite of about 98% mineral purity as determined by sink float techniques. It was anticipated that the wet processing through the grinding, milling and classification stage would yield a low cost 1µ ground product which should make available greatly increased applications for the mineral beyond those presently enjoyed. The improved purity was also expected to provide coarser sizes which might be utilized as a raw material for chemical modification which again would expand the uses of wollastonite. The evidence thus far collected appears to indicate that this premise may be expected to be fulfilled. There are on the surface of wollastonite particle sites at which cheinical reactions may occur1. It is believed that wet ground material provides a better base which will allow wollastonite a deeper entree into the field of chemical raw materials. Wet ground at 20µ and finer permits with certainty a number of chemical reactions, some of which are mentioned later in this article. While well crystallized wollastonite makes up the majority of the ore, the balance consists mainly of very weakly magnetic diopside of the hedenbergite-

Jan 1, 1965

By A. R. Denison

This field in 1933 continued as in 1932, although to a much less extent, to dominate the drilling and production situation throughout the oil business. The 2466 producers completed in this field during the year are 28 per cent of such wells completed in the United States. The 2556 completions reported in the five counties within which the East Texas field lies are 21 per cent of all such wells reported in the United States. It follows that with such a command of the development situation, every other factor with regard to this field has an important bearing on the entire oil business. As a consequence, the important developments in the East Texas field are the important developments of the year. Very little new productive territory was added to the already known limits of this enormous field. On the other hand, drilling has shown that with a few very minor exceptions this field is a continuous productive area, with a regular outline and no "dry spots" other than that of a single well surrounded by producing wells. Drilling was confined to the already proven limits of the field. This consisted essentially of more adequate coverage of leases by wells, the meeting of required offsets and the drilling of a large number of small tracts which developed from subdivision of larger leases due to court action and other causes. The allowable throughout the year was, with minor variable factors, on a per-well basis. With the steady decline in per-well allowable after May, every operator was faced with declining

Jan 1, 1934

By Walter S. Weeks

THE subject of the flow of air through a mine under the influence of natural ventilation has proved an elusive one. To my knowledge only cut and try algebraic solutions have been used where multiple paths are involved. The object of this paper is to present a method for the graphical determination of the flow induced by the natural ventilation pressure (N.V.P.) alone or in combination with a fan. The N.V.P., measured in pounds per square foot, induced by two columns of air between two horizontal planes at different elevations, is equal to the difference in weight of the two columns, assuming each to have a cross-sectional area of 1 sq. ft. Pressure in pounds per square foot is converted into inches of water by dividing by 5.19. Methods of calculating the N.V.P. have been discussed in the literature. In this paper, for simplification of exposition, the change in pressure due to the weight of superimposed air will be assumed directly proportional to the length of the column. The actual methods of calculating the N.V.P. do not affect the solutions to be presented. It must be realized that the precision to be obtained from the small- scale, inked diagrams presented is not as great as would be obtained from large-scale, penciled curves that would be used in practice. The accuracy of the curves does not warrant reading "volumes" closer than the nearest thousand cubic feet per minute. CASE I. DUCTS IN SERIES The simplest type of problem is to determine the flow when two shafts are connected by a crosscut, as shown in Fig. 1. In this example, the resistance of the shafts is to be taken as 0.0001 in. of water for a flow of 1000 cu. ft. per minute for a length of 1000 ft. The resistance of a crosscut is to be taken as 0.0005 in. of water for a flow of 1000 cu. ft. per minute. The small pressures necessary to cause changes in velocity will not be considered, because the accuracy of other obtainable data does not warrant their consideration.

Jan 1, 1938

By Eugene P. Pfleider

Research indicates that the cube diamond is a superior stone for drill bits. It can be oriented to combine a long cutting edge with structural strength and high resistance to wear. Test bits set with preferred orientation give double the bit life at astoundingly low diamond loss in comparison to oriented octahedral diamonds. A PROGRAM of research on the orientation of diamonds in drill bits has been under way for several years at both the United States Bureau of Mines Experimental Mine at Mount Weather, Va., and the School of Mines and Metallurgy of the University of Minnesota. Reports on past work done both in the laboratory and the field are available in the technical press.1,3,4 The results of such drilling, done under comparable conditions, show that bits having diamonds oriented in a direction that combines structural strength and greatest hardness not only can advance somewhat faster than random set bits but can do this with a unit diamond loss of 50 pct or less. Several bit manufacturers have initiated the training of diamond setters in the principles of orientation on the basis of the above-mentioned research results. The basic information on the crystallography and hardness variation of the diamond was presented in an earlier paper,' which pointed out that the diamond is several hundred times harder along certain directions and certain faces than on others. The same article discussed the drilling results obtained with a group of nine bits having octahedron diamonds set with on-point, positive (gouge) rake, and negative (drag) rake orientations. The testing of oriented cube diamonds is an extension of this research program, employing the same procedures and equipment (Hy Mac hydraulic drill unit, EXT diamond core bits, St. Cloud Pink granite) as previously described. This current work covers the test experience of seven bits set with cube diamonds running approximately 10 stones per carat. The individual stones were near perfect cubic form; hence it was simple to orient them in any desired direction. The cube is a comparatively rare crystal form of the diamond, although considerable numbers are produced from the Congo. It is understood that most of the cube diamonds are retained in Africa, where they are either used locally for diamond bit manufacture or ground up to make powder. They have been considered to be an inferior stone for drilling purposes.

Jan 1, 1954

THE great subject of interest in American affairs during February was the consideration of the proposed soldier bonus. This proposal was based upon the idea that, because most of the workers of the United States had enjoyed high wages during war, the soldiers were entitled to "adjusted compensa-tion" in order to equalize things. It overlooked the fact that the soldiers, themselves, had the opportunity to enjoy high wages in 1919 and 1920, when rates were highest. Apart from this, the whole project was founded on fallacies and involved what would be nothing less than economic crime. Although it looked as if the measure were destined to be railroaded through Congress, so great a storm of protest was pelted upon Congress that the present outlook is that the whole project will be abandoned. There was probably some increase in the physical volume of business during February. A rise in prices for agricultural products assisted the farmers mate-rially. These developments, however, are not to be construed as presaging any general upward movement. On the contrary, the current year is to be contem-plated as one of serious labor troubles, following inevit-able reductions of wages. These began in February in the form of an extensive strike in the cotton textile industry of New England, accompanied by some rioting in Rhode Island. The coal miners have had numerous conferences, without coming to any encouraging results, and the stage appears to be fully set for a general strike beginning Apr. 1. About the only question now is whether this will comprise both the bituminous and anthracite miners. If the latter refuse to go out, no serious shortage of coal is anticipated, the belief being that the existing stocks together with the output of the non-union mines will supply the demand, which is sub-normal even now. In the metal industries, lead and zinc were dull but stable. The weakening tendency in iron and steel that was manifest during January appeared to be checked, at least temporarily. Copper was charac-terized by a distinct weakness and a considerable decline in the market. This downward movement was inspired by the news during January that several of the important mining companies were taking steps to resume production. During February the demand for copper, both foreign and domestic, was poor.

Jan 3, 1922

By Robert S. Schecter, Paul M. Bommer

This paper presents the development of and results from a computer model of in situ uranium leaching. This model uses a streamline-concentration balance approach and is useful with a wide range of reservoirs. It can be used with any type of well system, in a reservoir with or without boundaries, and with any form of descriptive kinetics. The model also includes the effects of dispersion and consumption of oxidant by minerals other than uranium. The effects of areal sweep, variable uranium concentrations, variable permeability, and the presence of oxidant consumers on uranium production are shown and discussed.

Jan 1, 1979

By Orvar Nyquist, Klaus W. K. Lange, John Chipman

Liquid Fe-C-Si alloys containing 0 to 12 pet Si and up to 4 pet C were equilibrated with carburizing gases at 1550°C. Two to 5 alloys simultaneously were held in close proximity for 5 to 7 hr to establish uniform carbon activity in the group. Analysis of the data gives the activity coefficient of carbon as a function of the mole fractions of carbon and silicon, Fig. 7. Values of the interaction coefficients at infinite dilution are

Jan 1, 1962

By H. M. Warrren

IN the past, steam engines were used in practically all cases for driving the machinery, in and about an anthracite breaker, and hence little or no accurate data were available as to the power requirements for starting and operating the individual machines, which make up the complete equipment. It was impossible to segregate the power necessary to drive each individual machine, first, because the equipment was driven in groups, and second, because it was impracticable to obtain graphic, integrated, or instantaneous records of the horsepower used. As a result of these conditions, it was found, when individual electric motors were applied to the various machines, that more accurate and complete data were needed in order to provide motors of the proper power and design for the particular services to be rendered. In order to obtain the desired information, the writers made and collected a number of tests, from time to time, on the individual motor drives in- electrically operated breakers, and as these tests have been of great value, it occurred to them that a paper giving the results might be of service to other engineers interested in similar installations. Table I shows the .results of these tests. All the motors tested were of the three-phase, 60-cycle, 440-volt, induction, squirrel-cage type, except a few, which, on account of size and starting conditions, were of the wound-rotor type. The instruments used in making these tests were: An integrating watt-hour meter, a graphic ammeter, and a graphic voltmeter. These instruments were connected in each motor circuit, and a record of a day's run of 9 hours was obtained from each machine. From these tests, the running light load, the average all-clay load, and the instantaneous peak readings in amperes, volts, and kilowatt input, were obtained. By means of the characteristic curves obtained from these motors at the factory, the power factor, the efficiency, and the horsepower output were calculated for each particular test. Starting tests were made by the brake-arm method, in which the torque in pounds was measured directly on a spring balance.

Jan 2, 1916

Jan 1, 1948

By J. H. Swislzer

TWO-LIQUID miscibility gaps have been found to exist in both the CaO-SiO, system above 1705 and the Cr,03 system above 2200"c. Glasser and 0sborn3 studied the extension of these miscibility gaps into the Ca0-Si0,-Crz03 ternary system and reported that the two-liquid region is not present at temperatures below the monotectic temperature of 1705°C in the CaO-SiO, system. The present authors, in connection with other work on surface-tension measurements and foam stabilities in the same ternary system,4 observed that the miscibility gap exists at temperatures as low as 1600°C. A brief experimental study was devoted to deter- mining tie-line positions in the two-phase region. The technique used was to obtain a separation of phases at 1600°C, then to quench-in the high-temperature phases and obtain a chemical analysis of each phase. It was necessary to take special precautions in obtaining a phase separation because of a tendency toward emulsification of the two liquids. The procedure followed is described in the schematic drawing in Fig. 1. A small platinum crucible containing several pinholes on its sides was placed inside a larger platinum crucible. An excess of Crz03 was placed in the outer crucible, together with a prefused binary CaO-Si02 mixture, and the Cr203 was allowed to diffuse through the pinholes and saturate the same binary CaO-SiOl mixture in the smaller crucible. After equilibration at 1600°C, the inner crucible contained only the lighter liquid (liquid A) saturated with Cr203. The outer crucible contained layers of both liquids. Experimental data were obtained by analyzing the entire contents of the inner crucible and only the bottom layer of the larger crucible (liquid B). The upper layer of the outer crucible was not suitable for chemical-analysis purposes because dispersions of the second phase sometimes were found in the samples. The technique is described in more detail in Ref. 4. The same method was used by Grieveson and urkdoan' to study a miscibility gap in sulfate-ferrite melts, where the liquids were difficult to separate because of similarities in density. In addition to the phase-separation experiments, a few others were conducted to obtain information

Jan 1, 1964