Search Documents

Jan 1, 1942

[ ]

Jan 1, 1938

By K. H. Coats

This paper presents the development and solution of a mathematical model for aquifer water movement about bottom-water-drive reservoirs. Pressure gradients in the vertical direction due to router flow are taken into account. A vertical permeability equal to a fraction of the horizontal permeability is also included in the model. The solution is given in the form of a dimensionless pressure-drop quantity tabulated as a function of dimensionless time. This quantity can be used in given equations to compute reservoir pressure from a known water-influx rate, to predict water-influx rate (or cumulative amount) from a reservoir-pressure schedule or to predict gas reservoir pressure and pore-volume performance from a given gas-in-place schedule. The model is applied in example problems to gas-storage reservoirs, and the difference between reservoir performances predicted by the thick sand model of this paper and the horizontal, radial-flow model is shown to be appreciable. INTRODUCTION The calculation of aquifer water movement into or out of oil and gas reservoirs situated on aquifers is important in pressure maintenance studies, material-balance and well-flooding calculations. In gas storage operations, a knowledge of the water movemenr is especially important in predicting pressure and pore-volume behavior. Throughout this paper the term "pore volume" denotes volume occupied by the reservoir fluid, while the term "flow model" refers to the idealized or mathematical representation of water flow in the reservoir-aquifer system. The prediction of water movement requires selection of a flow model for the reservoir-aquifer system. A physically reasonable flow model treated in detail to date is the radial-flow model considered by van Everdingen and Hurst.1 In many cases the reservoir is situated on top of the aquifer with a continuous horizontal interface between reservoir fluid and aquifer water and with a significant depth of aquifer underlying the reservoir. In these cases, bottom-water drive will occur, and a three-dimensional model accounting for the pressure gradient and water flow in the vertical direction should be employed. This paper treats such a model in detail — from the description of the model through formulation of the governing partial differential equation to solution of the equation and preparation of tables giving dimensionless pressure drop as a function of dimensionless time. The model rigorously accounts for the practical case of a vertical permeability equal to some fraction of the horizontal permeability. The pressure-drop values can be used in given equations to predict reservoir pressure from a known water-influx rate or to predict water-influx rate (or cumulative amount) when the reservoir pressure is known. The inclusion of gravity in this analysis is actually trivial since gravity has virtually no efFect on the flow of a homogeneous, slightly compressible fluid in a fixed-boundary system subject to the boundary conditions imposed in this study. Thus, if the acceleration of gravity is set equal to zero in the following equations, the final result is unchanged. The pressure distribution is altered by inclusion of gravity in the analysis, but only by the time-constant hydrostatic head. The equations developed are applied in an example case study to predict the pressure and pore-volume behavior of a gas storage reservoir. The prediction of reservoir performance based on the bottom-water-drive model is shown to differ significantly from that based on van Everdingen and Hurst's horizontal-flow model. DESCRIPTION OF FLOW MODEL The edge-water-drive flow model treated by van Everdingen and Hurst1 is shown in Fig. la. The aquifer thickness b is small in relation to reservoir radius rb. water invades or recedes from the field at the latter's edges, and only horizontal radial flow is considered as shown in Fig. 1b. The bottom-water-drive reservoir-aquifer system treated herein is sketched in Fig. 2a and 2b. Here the aquifer

By R. A. Wyman

The overall approach to nonmetallic mineral flotation practiced in the laboratories of the Mines Branch, Ottawa, Canada, is outlined. The use of floatability tests to indicate possible areas of selectivity is indicated. Selected examples of the evolution of flotation systems are presented. Reagents are briefly discussed.

Jan 1, 1972

By F. H. McDowell

DURING the last eighteen months the Tilly Foster Iron Mine Company, the President of' which is Mr. E. I?. Hatfield and the Managing Director Mr. B. G. Clarke, has been carrying out a plan

Jan 1, 1889

By J. R. Kyte, V. O. Naumann, C. C. Mattax

Imbibition and waterflooding tests at reservoir conditions show that conventional tests at room conditions sometimes lead to recovery estimates that are too low. Core samples which are of intermediate wettability at normal test conditions may be strongly water-wet at reservoir conditions. This was found to be true for samples from two of three reservoirs investigated. For the other reservoir, less difference was observed between the wettability of samples at normal test conditions and at reservoir conditions. Samples which became more water-wet at reservoir temperature and pressure also water flooded more efficiently at reservoir conditions. These results show that core analysis tests on intermediate wettability samples should be performed at reservoir conditions to obtain representative data. INTRODUCTION Throughout the oil industry, core analysis tests normally are performed using refined oils and at room temperature and pressure. This procedure has always been subject to question because the possibility is generally recognized that the reservoir environment may influence displacement behavior. Burkhardt, et al,' have performed waterflood tests at reservoir conditions on East Texas cores. They found little difference between results obtained at reservoir conditions and results of conventional flooding tests at room conditions. As they pointed out, however, this situation might not be general since they obtained data on only one rock and crude-oil system. This paper presents data which demonstrate that it is sometimes necessary to perform core analysis tests in a simulated reservoir environment to properly represent the reservoir wettability and displacement characteristics. The work is specifically concerned with reservoirs which were thought to be of intermediate wettability on the basis of conventional test results at room conditions, i.e., core samples imbibed only small amounts of either oil or water and exhibited no decided preferential wettability characteristics. Tests were performed on cores from three such reservoirs to determine their behavior in the reservoir environment. lmbibition and waterflood tests were used to demonstrate the effect of reservoir environment on reservoir rock wettability and displacement characteristics. Results of tests performed at reservoir conditions were compared with results from conventional tests. Imbibition tests were performed on samples from all three reservoirs. Waterflood tests were performed on samples from only one reservoir. Fluid properties for the three reservoirs studied are shown in Table 1. Tests at reservoir conditions were performed using bottom-hole crude oil at reservoir temperature and pressure. The aqueous phase used in these tests was a synthetic brine approximating the reservoir brine composition. Conventional tests were performed at room conditions with refined oils and synthetic reservoir brine. The oil-to-water viscosity ratios were adjusted to the reservoir values. The cores used in all the tests were taken from the reservoirs using either brine alone or a bentonite-car-boxymethylcellulose mud without additives as coring fluids. Previous tests show that these fluids have no significant effect on the wettability of reservoir rock samples.1 The cores were preserved in brine at the wellsite to prevent wettability changes during shipment and storage. Wellsite imbibition tests have been performed on fresh samples from several reservoirs (including Reservoir A) and compared with later laboratory imbibition tests on samples preserved in brine. The comparison showed that the wettability of the preserved cores was the same as that of fresh, surfaced cores at the wellsite.2 IMBIBITION TESTS Conventional imbibition tests were performed on preserved cores using the apparatus and procedures described by Bobek, et al.2 A sketch of the apparatus for imbibition tests at reservoir conditions is shown in Fig. 1. The preserved samples were first centrifuged to expel excess water and then placed in a stainless-steel container which served

By G. A. Bole, F. W. Davis

The purpose of this paper is not to report, to the Institute, the results so far obtained in the survey, by the Bureau of Mines, of the metallurgical requirements for open-hearth refractories, but to present an outline that we hope will serve as a basis for discussion. The systematic survey that the Bureau proposes to make has not been outlined, although considerable preliminary work has been done in the way of interviewing open-hearth superintendents in several of the larger steel plants from the Chicago district eastward. At the several conferences so many of the opinions were diametrically oppoeite, when considering the same point, that it was thought that such an opportunity as the Institute offers in the way of a clearing house for moot metallurgical topics should not be overlooked. For this reason, the paper has been prepared as a basis for a discussion which, it is believed, will be of value in outlining the program of the Bureau. D. A. LYoN, Assistant Director. The importance of securing suitable refractories for metallurgical operations is daily becoming more universally recognized; particularly in the manufacture of open-hearth steel, where the life and earning power of the furnace depends largely on the judgment and care exercised in the selection of the correct quality of refractory for each of the parts. Any innovation that would make available to the steel manufacturers refractories with longer life or better suited to their needs than those now employed, and at a cost that would permit of their use, would be of enormous value to the industry at large. It is quite probable that revolutionary changes would not be necessary. Material now used in some parts of the furnace might, by more suitable preparation, be made of much greater service; in other parts, possibly entirely different material would be necessary in order to effect much improvement. Inasmuch as different parts of the furnace structure perform different functions and are subjected to different service conditions, a refractory suitable for one part will be entirely unsuited for another. For this reason, to make a comprehensive study of the refractory requirements of the processes, we should consider the furnace as built up of a number

Jan 1, 1924

By A. Filyk

The current plant practice at Molycorp, Inc., Questa Division, a molybdenum producer in northern New Mexico, is described. An outline of crushing, grinding, flotation, drying, and tailings disposal is included, with emphasis on metallurgy.

Jan 1, 1976

By Alexander B. Morris

In a recent paper on the intermittent injection of gas in gas-lift operations as opposed to continuous injection, Morgan Walker presented a comparative table showing the effect on oil and gas production from the same wells under the two methods of operation.' This table carried a column showing the formational gas-oil ratios under each method, computed by deducting the volume of input gas from the volume of trap gas. During the entire spring and summer of 1928, the present writer had been engaged on some extensive test car tests of rich gas in Glenpool, seeking, primarily, for an explanation of the apparent loss of gasoline during the summer season between the field meters and the plant master meter. Tests at several of the field meters where the richest gas was obtained regularly failed to check with other tests on the same gas made farther along the line, and the difference was not made up by the quantity of drip gasoline collected between the points. In the course of these tests, the final outcome of which is immaterial to the present purpose, an attempt was made to construct a curve representing the relationship between gasoline content of the gas in gallons per thousand cubic feet and the shrinkage in the volume of gas treated as a result of removing the condensible fractions. Such a curve was made, expressed in units of gallons per thousand cubic feet on the abcissa and the ratio vapor volume to liquid volume on the ordinate. This curve is a rectangular hyperbola and shows that 3 gal. of gasoline taken from 1000 cu. ft. of raw gas as a vapor occupied much less space, per gallon, than did 1 gal. of gasoline taken from 1000 cu. ft. of another sample of gas. This is, in general, corroborated by converting to the same units the residue settlement curves prepared by the Tidal Oil Co. and by the Natural Gasoline Manufacturers Assn., though the three curves, when plotted together, occupy entirely different positions on the paper, as shown in Fig. 1. The bearing of all this on Mr. Walker's discussion of gas-lift is this: if the formational gas is to be computed by deducting the input gas from the trap gas, some correction must be made for the vapor volume

Jan 1, 1930

By John D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space.

Jan 9, 1959

INTRODUCTION TO PROBABILITY THEORY The mathematical theory of probability provides the foundation for the interpretations and inferences that can be made from statistical techniques. Probability theory is a broad field of study in itself, and can only be touched on here in order to provide the necessary back- ground for a more complete understanding of statistical analysis. Probability is concerned with the outcome of random events. It had its beginnings in the theory of games of chance which were of great interest to European mathematicians during the last half of the 17th century. The outcome of a random process or experiment is defined as an event. The collection of all mathematical points associated with each event is called the sample space for an experiment. Consider a random experiment having a finite number, n, of possible outcomes, some of which have a characteristic A. What is the probability that A will result from a single

Jan 1, 1980

By Richard H. Willey

Efficient handling of large tonnages in open-pit mining demands, primarily, an abundance of well fragmented rock. To accomplish this, a drilling and blasting department composed of a well-knit, versatile group of workers and supervisors must be established. Some costs will remain relatively on the same level over a period of years, while others can be greatly lowered as will be shown. 'The Utah Copper Division, Kennecott Copper Corp., Bingham Canyon, Utah, has been ever alert for improvements in operating methods and equipment to gain increased efficiency and lower costs. Bingham Canyon MIne The greatest dimension of the mine is 8000 ft northeast-southwest with a width of 5000 ft southeast-northwest. From the lowest level, at an elevation of 6040 ft above sea-level, the mountain rises in 27 benches on the west side to W level (elevation 7800 ft) and 21 benches on the east side to Q level (elevation 7460 ft). At the inception of open-pit mining in 1906, the overcapping of leached porphyry had to be removed to reach a commercial grade of sulphide ore. The overcapping or waste now remaining is quartzite with intercalated limestone beds. The limestones are usually soft in nature except in the south-middle portion of the mine where they have been meta-morphized along the contact zone. This area usually gives drilling and blasting operations a great deal of trouble. Here occurs the greatest amount of secondary blasting, as the well-established fracture planes cause the altered beds to break into large boulders. Several massive quartzite "ribs" occur in the overburden, and as a result, the uniform breakage is difficult to obtain. The major quartzite areas have been subjected to complex folding, fracturing and faulting because of the intrusion of the underlying stock. The monzonite porphyry, which carries the commercial values, presents no serious drilling problem because of its softness and extensive minute fracturing throughout the mass. A series of major slips or faults pass through the ore body which, although of considerable advantage to the drilling and blasting department, sometimes works to the disadvantage of the track department. Drilling an11 blasting of the porphyry apparently becomes easier as depth is attained. but highly siliceous streaks throughout the pit still present difficulties. At no place is the rock of such character as to allow excavation without preparations. On certain higher elevations or levels, old fill material can be dug by the shovels, but only at some risk to equipment because of bank slippage. Past Methods At the outset of shovel operations in 1906, drilling was done with the Ingersoll-Rand F-24 piston drill mounted on an un-

Jan 1, 1949

Man: A purely detached consideration of nature and the place of man in it may easily result in somewhat pessimistic conclusions as to man and his destiny. However, when we come to the evaluation of man's role in the development of natural resources and his achievements in this field, a more optimistic tone may be justified. Hence the possible contradictions between Man and Nature, Perfection, and the present chapter are more apparent than real. After all, progress must have a foundation of optimism, and we cannot challenge either the faculty or the students to better work and to a progressive and constructive outlook without an underlying tone of optimism and basic faith in the future. Geology is the basic science of Mother Earth; the science of the natural forces that have produced and modified the structure of our globe; the science of minerals and rocks; of landscapes and soils; of water supply and mineral resources, including mineral fuels; and of the history of life, both plant and animal, as revealed by fossils in rocks. It is difficult to reduce man and his historical significance to their proper relationship with regard to the earth and its history. Processes of rock formation have continued for at least two billion years; man's activities have been in evidence only a few thousand years. As a means of comparison, if the height of the Empire State building were to represent geologic time, the thickness of a nickel placed on the tower would just about repre-

Jan 1, 1950

By Don H. Baker

THE need for new or improved refractory materials has caused metal phosphides to be given renewed scrutiny. Some metal phosphides show high-temperature inertness, are exceptionally hard, and exhibit a marked resistance to chemical attack. Various metal phosphides have been prepared for study by direct combination of the elements,'-' by reaction of metal or metal compounds with phosphine or phosphorus trichloride,'"' by thermal decomposition of a metallic phosphate or phosphite,"-'8 and by molten salt electrolysis.19 Electrolytic preparation of phosphides of titanium, manganese, and chromium from their oxides is reported in this paper. An externally heated 3-in.-ID by 6-in.-deep graphite cell, that served as the anode as well as a container for the electrolyte, was used in these investigations, and a suspended, centrally positioned graphite rod served as the cathode. A closely fitting silicon carbide furnace liner minimized atmospheric oxidation of the crucible. Electrolyses were performed for predetermined periods and current settings. Preliminary research had indicated the more efficient current and potential settings that could be used. Upon completion of the deposition period, the deposit was hot-stripped from the cathode. The mass of crystalline deposit, plus occluded and adhering salt, was crushed to minus 10 mesh and hot-leached in dilute hydrochloric acid. The leached crystalline material was water-washed, dried, and sampled for analysis. Products were identified by X-ray diffraction and standard analytical procedures. Electrochemical studies were initiated to establish the optimum conditions necessary to produce manganese phosphide (MnP), titanium phosphide (Tip), and chromium phosphide (CrP). Among the factors studied were the operating temperature, the imposed current, and the electrolyte system. If the temperature, or imposed current, was too high, deposition of phosphorus resulted, and if either were too low, partially reduced lower oxides were deposited. The operating conditions established for repetitive high-quality production of metal phosphides of the MP structure are presented in Table I. The metal phosphide crystals varied in size, but all had a definite metallic appearance. Typical are the crystals of CrP shown in Fig. 1. Evaluation data and analysis of the crystals are presented in Table 11. Efforts to measure resistivity of these three compounds over the temperature ranges of 250o to 400°K were hampered by the small physical size of the crys-

Jan 1, 1968

By William E. Newman

Lead mining has been carried on in several localities of the Province of Ontario in a desultory fashion for the past 60 years, but up to 1916 the results have not been of much commercial importance. The most ambitious attempt was made by an English company which built a lead smelter at Kingston, Ont., in 1880 to treat the concentrates from the Frontenac mines. After 2 years' operation, the mines and smelter were abandoned. Up to the present there has not been a sufficient tonnage of concentrates to support an efficient blast-furnace plant and as most of the small properties could not stand the heavy freight and duty charges into the United States, development work has not been carried on in a systematic manner. As a result the industry has languished. At Galetta, in southeastern Ontario, considerable prospecting and development work has been carried on in the last few years and very promising deposits of galena have been found in the Chats Island group by the James Robertson Co., Ltd., of Montreal. The chief deposit is that of the Galetta or Kingdon lead mine, located on Chats Island in the Ottawa River about 5 miles east of the town of Arnprior. The rocks1 in the vicinity of the mines consist of an interbedded series of crystalline limestone and biotite gneisses of pre-Cambrian age. This part of the Ottawa River basin has been severely faulted and the overlying Paleozoic limestones may be seen in normal fault cantact with the pre-Cambrian. The vein filling is of a very well-marked fault fissure type and although the amount of displacement is not determined at this point, similar faults to the east show a displacement of from 1,500 to 1,800 ft. which would indicate mineralized fault fissures of considerable depth. The ore occurs in a highly crystalline calcite with some barite and fluorite, and the galena occurs more or less richly disseminated in clusters and crystal aggregates. In some cases these masses weigh several hundred pounds. Small amounts of sphalerite are occasionally encountered.

Jan 1, 1918

By George W. Maynard

In the Journal of the Iron and Steel Institute for the year 1878, in the account of the proceedings of the annual meeting in March of that year, when Mr. Bell read his paper On the Separation of Phosphorus from Pig-Iron, occurs the following statement, as part of the reported discussion of that paper: " Mr. Sidney Thomas stated that he had succeeded in effecting the almost complete removal of phosphorus in the Bessemer process. Experiments had been carried on at Blaenavon, with the co-operation of Mr. Martin, on quantities varying between 6 lbs. and 10 cwt., and some hundred analyses made by Mr. Gilchrist (who had the conduct of the experiments from the first) showing the removal of from 20 per cent. to 99.9 per cent. of phosphorus in the converter. He believed the practical difficulties in the way had been overcome, and that Cleveland pig might be made into good steel without any intermediate process. He hoped on a future occasion to lay full details before the Institute." I was present at that meeting, and I doubt if any one in the hall knew, either by sight or name, the young man who had dared to rise in that august body and claim that he had accomplished that after which the great metallurgists of Europe had been unsuccessfully striving ever since Mr. Bessemer's great discovery. I remember distinctly the pitying smile of derision and the stony stare

Jan 1, 1885

By George Breyer

DURING the past 25 years the steelmaker has experienced some difficulty in producing steel to meet the standards established by the metallurgist. In contrast to the past, when a chemical specification of broad limits was the only requirement, he now has to employ such tests as microscopic, macroscopic, tensile, impact, Magnaflux and even X-ray and supersonic. The development of these tests has more than set the pace for a manufacturing process of which the exactness still hinges to an important degree on the ability of the furnace operator. In our efforts to produce steel, and especially alloy steel, to meet the exactness of modern engineering specification, many factors must be taken into account. It is not sufficient to make a good heat of steel in the furnace and then be satisfied that the job is done, since there are many pitfalls between the furnace and the finished product. The literature abounds with information on melting practices, deoxidation methods and slag control, but the lack of positive information about what happens when the steel is teemed into molds is quite evident. Such questions as what is the proper mold size, shape and thickness; which is the best mold coating; what is the best rate of pour for any given steel, and what is the effect of cooling rates on quality, are still answered by opinions. It is acknowledged that a poor heat of steel cannot be improved in the pouring pit. On the other hand, a good heat can be ruined by improper handling after it leaves the furnace.

Jan 1, 1947

By C. R. Hocott

THE distribution and movement of fluids in oil reservoirs are influ-enced to a great extent by capillary forces, which depend upon the size and shape of the pores in the reservoir rock, the surface characteristics of the rock, and the interfacial tension between the fluid phases. This paper presents the results of an investigation of the interfacial tension between salt water and crude oil containing dissolved gas under reser-voir conditions. APPARATUS AND PROCEDURE In the preliminary phases of this investigation, it was found that a scum formed at the oil-water interface, which made measurement of interfacial tension by either the ring or capillary rise methods unreliable. Accordingly, the drop-weight method, in which a fresh interface is con-tinuously formed, was selected. In this method, a tip through which drops of one fluid can be expelled is immersed in a second fluid. At the instant that the drop becomes large enough to fall, the gravitational force tending to pull away the drop exactly balances the interfacial force tending to hold it. From the size of the drop, the dimensions of the tip, and the density of the two fluid phases, the interfacial tension may be calculated. The apparatus consists of a circulating pump for bringing the oil to equilibrium with gas at the desired pressure, a displacement pump for forming the drops, an interfacial tension cell in which the drops are formed, and a density cell to determine the density of the oil. The density of the water is determined separately in another apparatus. A flow diagram of the assembled equipment is shown in Fig. 1.

Jan 1, 1938

By Herbert F. Miller

For a long time I have believed that the gas- and brick-costs of open-hearth furnaces using prodncer-gas could be greatly decreased by a change in the design of the port, which would materially reduce the first-cost of the furnace, the rebuilding-cost, and the repair-cost. The defects of the present type of such furnaces, which has clone duty for so many years, may be studied in Fig. 1, in which A A are the two air-uptakes, B is the gas-uptake, and C the end of the gas-port. In the present type of furnace, C is practically 011 the edge of the bath and therefore combustion begins to take place at that point, but has no effect until the gas passes from 5 to 10 ft. into the hearth. As the furnace grows older, C moves back by reason of the burning or falling down of the arch. The furnace reaches its highest efficiency when C has moved a certain distance, but is still near enough to the bath for the overhead layer of air to hold the gas down on the bath, and far enough back to permit combustion to take place at some distance from the bath. This latter fact means that the temperature is sufficient to melt steel at the edge of the port. From this time on, the furnace decreases in efficiency. What is the reason ? As C moves further hack, the gas is released from the gas-port at a point where there is little or no overhead layer of air. The result is that the gas floats along the roof, with the air mostly underneath it. Why the air does not stay over the gas is readily seen in Fig. 1. The lines of draft naturally run parallel to the length of the furnace. The air-uptakes being on the sides and the gas-port in the middle, most of the air will naturally be drawn along the sides of the furnace and the layer of air will be thinnest over the gas, where it is most needed.

Jan 1, 1914

By Michael A. Arkoosh, E. A. Peretti

ANALYTICAL results have previously been presented for the diffusion-controlled solution of a second phase in a finite medium for planar, cylindrical, and spherical geometries.' These results were obtained by numerical methods using digital computer techniques and are applicable not only to the stage of the problem where the unstable phase shrinks to zero size, but also the subsequent stage where the concentration gradients in the matrix phase become negligible (essentially complete homogenization). It is anticipated that the results of such an analysis may be of use to those workers who are interested in the processes

Jan 1, 1970