Search Documents

By Nicholas J. Grant, Noboru Komatsu

Metallographic and X-ray studies were made of oxide dispersion strengthened Cu-12 vol pet SiO2 and Cu-3.5 vol pet Al2O3 alloys following time exposures at temperatures approaching the melting. point of the matrix metal. Changes in hardness, oxide particle size and crystal structure were studied to determine the time-temperature stability of these alloys. An interpretation of the mechanism of oxide agglomeration is proposed. One of the most striking features of dispersion strengthened metal-metal oxide alloys is their stability at elevated temperatures, both with respect to recrystallization and maintenance of mechanical properties after exposure at high temperatures. A small amount of work has been done on the re-crystallization phenomenon in dispersion hardened metal-metal oxide alloys'l and several theoretical treatments have been advanced regarding the stability of these alloys by Lenel and Ansell,8 and by Grant and his co-workers.9, 10 This paper reports on metallographic and X-ray studies following various heat treatments of Cu-AI2D3 and Cu-SiO2 alloys at elevated temperatures and the effect of subsequent cold work on the recrystallizalion temperature. An interpretation of the recrystallization behavior of this type of alloy, based on the decomposition and agglomeration of oxides, is proposed. EXPERIMENTAL PROCEDURE Cast ingot bars of copper-1.59 pet Si and Cu-0.77 pet Al, 7/8 in in diam, were annealed in argon for 80 hr at 1000CC for homogenization. The homogenized rods were machined into fine chips and ball milled. Milled particles in the range minus 20 to plus 60 mesh were separated for internal oxidation. The internal oxidation was accomplished by the same method used by Preston and Grant,9 except that the oxidalion temperature for the Cu-Si alloy was 750°C, and for the Cu-A1 alloy was 800°C. These powders were then hydrogen-reduced at 450°C, compacted in a copper container, evacuated at room temperature to 0.04 µ, and sealed for extrusion. They were extruded at 1400°F (760°C) with a ram speed of 55 in. per min for an extrusion ratio of 15.6 to 1 to give a rod 0.38 in. diam by about 3 ft long.

Jan 1, 1962

By Kenric C. Owen

INTRODUCTION Situated 23 miles east of Pretoria the Premier Mine started diamond production in 1903. Two years later it produced the largest diamond yet discovered, the 3 106 carat Cullinan stone. For the period to 1932 when the mine was closed down due to economic circumstances, open cast mining was practised using inclined rope haulage traction and by this time had produced 48.5 million carats of predominantly industrial quality diamonds from 148 million tons of ore. In 1945 it was decided to re-open the mine using underground mining methods. A system using long hole benching was devised (Hodgson and Sewel 1960). This system was later modified but still forms the basis for approximately fifty percent of production. Following the successful introduction of block caving on associated diamond mines in the Kimberley area (Gallagher and Loftus 1960) this mining method was introduced to the Premier Mine in the late 60's and now accounts for nearly 50% of production. This paper will discuss block caving at Premier Mine in the light of our experience and discussion will be directed to the main geological and structural features of the orebody and host rocks and the related constraints imposed on the mining methods. Reference is made to the long hole benching mining method for comparative purposes. GENERAL DESCRIPTION OF OPERATIONS The ore from the block caving and bench mining areas gravitates via ore passes to a twin haulage, 500m below surface. Electric 13 tonne locomotives, each hauling a train of 10 Granby type cars, deliver the ore to two 42" x 48" (1.06m x 1.22m) jaw crushers. The ore is reduced in size to minus 0.15m before being hoisted to the treatment plant on surface. Hoisting is done with 12.5 tonne bottom discharge skips in a five compartment rectangular shaft using two 3 240 H.P. semi automatic Ward Leonard winders. A small single drum service winder operates in the other compartment. Men and materials travel in a separate shaft in a 5,4m x 2,8m cage operated by a Koepi winder. These two shafts are also the main intake airways to the mine. The two main extraction fans capable of 250 m3/s at 3,2 kPa are situated on surface and are connected to the underground workings by an incline and a network of air passes and return airways. GEOLOGY Although there are numerous occurrences of kimberlite bodies in the district, the Premier Mine kimberlite pipe is the only economic orebody. It is roughly oval in shape with surface dimensions of 900m on the long axis and 450monthe short axis. The surface area is 320 000 m2. The kimberlite has intruded a massive body of felsite and norite which is intersected by a number of faults. The contact between the kimberlite and host rock is clear cut and dips inward at an average angle of 80°. Cutting across the pipe and the country rock is a 75 metre thick gabbro sill, the top of which intersects the pipe below the 347m level and dips at 15' to the north west. The kimberlite has been metamorphosed a distance of some 20m both above and below the sill contacts. Age measurements on biotite from the gabbro date the sill as 1 115 million years, thereby providing a minimum age of the pipe. (Pre Cambrian). All other pipes in South Africa are of Cretaceous age (60 million years). A simplified geological plan and section of the Premier Mine orebody is shown in Figure 1. It is thought that the kimberlite intruded in at least three distinct phases. The kimberlites of these different phases can be distinguished most easily by their characteristic colour. BROWN KIMBERLITE. This is the oldest kimberlite and forms a crescent shape in plan on the south eastern side of the pipe. In depth it increases in relative area. Although the brown kimberlite carries the highest diamond grade in terms of carats per ton all the various kimberlites in the Premier pipe are economic to mine.

Jan 1, 1981

By R. F. Hinds

A pressurizing system was designed and built to apply a radial pressure of 5.000 psi to rock samples. Samples of the Bradford, Weir and Kirkwood sandstones were subjected to radial pressures parallel and perpendicular to the bedding in the system and the changes in conductivity, porosity and permeability were deter-mined. Asymptotic decreases in conductivity, porosity and Klinkenberg permeability were observed over the 0- to 3,500-psi range. From these data, the increase of formation factor over the same range was calculated. The cementation exponent expressed in the Archie equation was found to increase with pressu,re. The rate of change varied from formation to formation. Only small differences were observed for samples taken parallel to the bedding as comnared to those taken perpendicular to it except for the Bradford sand. Above 3,500 psi the data are not good enough to tell if the properties continue to fall-off asymptotically or in a different manner. A possible explanation for the probable litnit of the asymptotic rate around 3,500 to 4,500 psi is that this represents the maximum pressure which the formations have unrdergone during their geological life as a result of burial. INTRODUCTION For many years measurements have been made in the laboratory of the properties of oil-bearing sandstones with little consideration being given to whether these properties had been changed when the samples were moved from their original position in the ground to the laboratory. Relatively little has been reported in the literature on the effect of pressure on the properties of sandstones. The changes in permeability for eight typical consolidated oil-bearing sandstone samples with overburden pressure (0- to 15,000-psi range) was presented by Fatt and Davis' in graphical form. In 1953 Fatt' also reported the relationship between porosity and overburden pressure for four typical consolidated oil-bearing sandstone samples (0- to 5,000-psi range). Fatt later described the changes of formation factor and porosity of 20 typical oil-bearing sandstone samples with overburden pressure changes (0- to 5,000-psi range) giving the values of the coefficients and exponents in the Archie' equation, and the more general Winsauer equation', where C, k and m are empirical constants, F is the formation factor, and + is the porosity. During the experiments of this investigation the core was contained in a neoprene rubber sleeve as shown in Fig. 1. It was held between two steel end members which were mounted in a steel cylinder. The unassembled pressure cylinder with its component parts is shown in Fig. 2. The core was insulated from the two steel end members by a Teflon sleeve with a small hole in the

By C. R. Fettke, Bela Hubbard

During the summer of 1916, while on a visit to the United States Agricultural Experiment Station at Mayaguez, Porto Rico, the writers were told by D. W. May, the director, that an occurrence of manganese ore had been reported from the mesa southeast of Mayaguez. A visit to the locality showed that the mesa is covered by a mantle of bright red soil resting upon serpentine. Here and there over its surface concretionary masses of limonite have been mashed out of this soil. These were apparently mistaken for manganese ore. On account of the similarity of this occurrence to the extensive iron deposits of northeastern Cuba, it was thought that a brief description based upon a two days'reconnaissance survey of the area mould be of scientific interest. Mayaguez is on the west coast of Porto Rico, at Mayaguez Bay, which is the third in importance of the harbors of the island. The city itself is about 3/4 mile inland on the low-lying plain at the mouth of the

Jan 1, 1920

By P. K. Lucke

ONE of the interesting features connected with the great continental uplift, which formed the table land of Mexico, is the great depth to which oxidation and secondary enrichment of orebOdies occurred. This table land lies at altitudes ranging from 4000 to. 7000 ft. (1219 to 2133 m.) above sea level. Several cases could be cited of oxidized zones in copper and lead mines which reached depths of upward of 1500 ft. (457 m.) below the surface, and it is universally admitted that the oxidized zone in a mine is limited by the permanent water level. FIG. 1. Mexico, however, like many other countries in which deserts occur, is visited at rare intervals by tremendous floods, which sometimes cause variable water levels over long periods. The following cases bear out the idea, and lead to interesting conclusions of commercial value. My paper demonstrates that carbonates of ores may occur below water level and sulphides above, and I will endeavor to explain the causes of the phenomena in certain specific instances.

Jan 6, 1918

By P. K. Lucke

One of the interesting features connected with the great continental uplift, which formed the table land of Mexico, is the great depth to which oxidation and secondary enrichment of orebodies occurred. This table land lies at altitudes ranging from 4000 to 7000 ft. (1219 to 2133 m.) above sea level. Several cases could be cited of oxidized zones in copper and lead mines which reached depths of upward of 1500 ft. (457 m.) below the surface, and it is universally admitted that the oxidized zone in a mine is limited by the permanent water level. Mexico, however, like many other countries in which deserts occur, is visited at rare intervals by tremendous floods, which sometimes cause variable water levels over long periods. The following cases bear out the idea, and lead to interesting conclusions of commercial value. My paper demonstrates that carbonates of ores may occur below water level and sulfides above, and I will endeavor to explain the causes of the phenomena in certain specific instances. Case I.—Fig. 1 in this case shows that sulfides of lead remained

Jan 1, 1920

By Lyman H. Hart

Some of the significant facts that will affect the supply and demand for metals during the next few decades are given in this presentation. This is important because the only hope for intelligent guidance of the national destiny depends upon presenting a consistent and accurate picture of basic problems. The metals problems now fomenting are only slightly less important than those precipitating the energy crisis. Admittedly, it is difficult to generate serious thinking on this subject when the world is enjoying easy access to all metals at modest prices. This is possible because of the current world capacity to over-produce, and United States credit standing, at least up to now, has permitted buying freely on world markets. Although both these vital conditions are subject to change, there is little doubt that if the U.S. financial house is kept in order, we can muddle along for a while on a generally expanding, metal-based economy. But should our credit standing be permitted to collapse, or should there be a tightening of world supplies of metals, the nation would immediately find itself in trouble. Unfortunately, clear signals indicate that both of these conditions are threatening. The metal age started many centuries ago, and with the exception of the noble metals, barely a dent was made in world reserves until the present century. Then, as a result of the pioneering ideas of D. C. Jackling and Paul Gemmel, and the willingness of the McNeals, Penroses and Guggenheims to back ideas with money, a virtual explosion of metal production was propagated throughout the world. It is important to examine the causes of this expansion to determine whether it is a trend that may be sustained or whether it is anomalous and therefore attributable to circumstances not likely to be repeated or continued. This period of plenty is a once only phenomenon. Vast metal resources have been sitting around here for eons, while the world was unaware of or unconcerned with their existence. But when population began to grow exponentially, and ways were discovered to use metals to develop machines to do the work of men and animals, the exploitation of raw materials increased at a staggering rate. And now the realization is dawning that minerals are a wasting asset and are beginning to present supply problems that should begin to be of concern. Two main factors have caused this condition; One is the population growth, and the other is the expanding demand for irreplaceable raw materials as nations become more developed. A group of systems analysts, at Massachusetts Institute of Technology in a book Limits of Growth, has warned that at present rates of population growth and resource consumption together with environmental constraints, a point will be reached within 100 years when the world population will become totally incapable of supporting itself. The authors conclude that this end result could be avoided if a planned equilibrium could be established at a lower rate of population growth and resource consumption. Fortunately, there is evidence that the population problem is moderating. The growth rate in the U.S. has decreased from 2.3% per year in 1900 to 1.1% in 1970. But, even at the lower rate, population will double in 70 years. The world rate is greater, and if it continues, world population will rise from 3.5 billion to nearly 10 billion in 50 years. All of these projections are questionable because the dangers of growing population are now being recognized. A marked decrease in growth rate has been noted in the more developed countries-in fact, it was zero in the U.S. in 1972. The other factor affecting consumption of raw materials is the increase in per capita use of most items as individuals become more affluent. Many economists believe that developing countries such as China and India represent a vast future potential market; but there are others, with whom the author agrees, who believe over-population tends to stagnate development. Nevertheless, it is a fact that vigorously developing societies increase consumption at a rate far above their population growth rate.

Jan 1, 1974

By C. Chiou, D. P. Seraphim

The effect of clustering on the superconducting properties of Al-Zn alloys has been studied by the ballistic induction techniques. The superconducting critical temperature, T,, changes when zinc-rich clusters are formed. The change in T, depends on the concentration and may be positive or negative, but always correlates with an effective decrease in the solute concentration of the alloy. Reversion after clustering effectively returns a 5 at. pct Zn alloy to the quenched state. These methods might be use&lly extended to the Al-Mg system, where X-ray data are difficult to obtain. In very dilute Al-Zn alloys, as in other tin,' indium, aluminum,2 or tantalums base solid solutions, there is a decrease in the superconducting critical temperature, Tc, roughly proportional to the temperature independent resistivity, i.e., -0.2°K per pS2cm. With increasing solute concentration, the T, generally reaches a minimum and then increases4 to a value well above that for the pure solvent. The change of T, with solute concentration follows an empirical formulation involving two constants which correlate with the scattering cross section of the impurities. As will be shown below, the Al-Zn alloys more concentrated than 1or2at. pct do not follow the empiricism, probably because they are unstable even when rapidly quenched.5 However, it seems possible to study at least the later stages of solute clustering by precise measurements of the 1', following various thermal treatments. A few experiments on quenched alloys, aged alloys, and tests on reversion are reported here. The heat treatments selected for obtaining the quenched and aged states were mainly deduced from the work of Dash and Fine.6 For the quenched state, specimens were homogenized at 480°C, quenched to -160°C, and immediately transferred and mounted in liquid nitrogen. Measurements on the superconducting properties and residual resistivities were then made at helium temperatures, after which the specimens were aged at room temperature for 3 to 5 hr, i.e., much longer than the time required for clustering to be essentially completed. The superconducting properties and residual resistivities were once again examined. To reach the reverted state of the A1-5at. pct Zn alloy, the aged specimen was heated for 5 min at 200°C and then tested as above.

Jan 1, 1963

By Thomas L. Kesler

IF all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig. 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig. 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin.

Jan 10, 1951

By William Hall

THE product obtained by roasting stibnite is likely to contain some unoxidized antimony trisulphide and a mixture of antimony trioxide and antimony tetroxide. It was desired to determine, as accurately as possible, the condition of the antimony as well as the total quantity present. Attempts were made to separate the trisulphide and the two oxides by methods based upon their varying solubilities in different solvents, but no satisfactory results were obtained in this way. It was found, however, that by determining the total antimony content, the antimony present as trioxide, and the antimony present as trisulphide, a good idea of the chemical composition of the roasted product could be obtained. The total antimony was determined by dissolving the sample in concentrated hydrochloric acid, reducing the antimony entirely to the trivalent condition by means of hydriodic acid and eventually titrating the antimony back to the pentavalent condition by means of iodine in the presence of sodium bicarbonate.' The details of the procedure are as follows: Weigh out 0.25 gram of the roasted product into a trapped flask (Fig. 1), add 4 grams of powdered tartaric acid, 2 grams of potassium iodide and 40 c.c. of concentrated hydrochloric acid. Boil the solution gently for 5 min. and then cool to room temperature by shaking the flask while holding it under running water. Then, very carefully discharge the iodine color by the cautious addition of 0.05-normal sodium thiosulphate solution, adding a little starch toward the last. Nearly neutralize the acid with ammonia solution, but leave the solution distinctly acid. Pour the slightly acid solution into 200 c.c. of water con-

Jan 1, 1916

By C. B. Post, G. V. Luerssen

J. STEVENS*—The authors state that the contamination in the metal was due mostly to the ladle refractories. Did the contamination vary with different brands of refractories or different qualities in the ladle ? C. B. POST (authors' reply)—That would be expected. In our shop we have used a grade of firebrick which is fairly standard. We do use high refractory nozzles to combat this erosion and high refractory sleeves, but there is such a problem when you get a skull in a ladle you just cannot use these high refractory bricks; you rip out the whole ladle getting the skull cleaned up. The acid bricks form a glass, and you can pull the skull out when you do get them. I believe you might find variations among the different refractories depending on how much silicon is in the brick. This determines how much silica is going into the interface between the steel and the brick. Our brick is about 35 pet alumina and 65 pet silica. With a brick of 35 pet alumina in the slag patches new calculations would have to be made. R. PARDEE*—Where can you draw the line in determining the refractories as being a silica refractory ? C. B. POST—More silica than about 50 pet. I think perhaps that is generally the criterion. The brick we use is a good high grade fire brick. T. S. WASHBURN*--With reference to the higher silicon that is recommended as a result of this investigation, is it contemplated that the specified range would be raised to 0.40-0.60 pet silicon, or possibly 0.50-1.00 pet silicon? These higher silicon ranges would affect the physical properties of the steel and consequently there might be some complications with respect to educating the consumers to 'accept this revision of the conventional analysis. C. B. POST—It will take considerable work. Take AMS 6260 as an example. Ordinarily this specification calls for 60 or 75 manganese. Silicon has some

Jan 1, 1950

By H. A. Doerner, F. D. DeVaney, J.B. Clemmer

Production of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaC03) and dolomite (MgCO3. CaC03). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedra1 crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent SiO2, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 SiO2 and 6.5 R2O3. The percentage reported as R2O3 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe2O3, A1203 and TiO2. The sorted magnesite product is not the best grade. even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1943

By J. B. Clemmer, F. D. DeVaney, H. A. Doerner

Production of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaC03) and dolomite (MgCO3. CaC03). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedra1 crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent SiO2, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 SiO2 and 6.5 R2O3. The percentage reported as R2O3 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe2O3, A1203 and TiO2. The sorted magnesite product is not the best grade. even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1943

By L. W. Bahney

(Cleveland Meeting, October, 1912.) THE photograph, Fig. 1, shows the apparatus a little less than half size, consisting of a filtering-flask fitted with rubber stopper, through which passes a bent glass tube, and an extraction-thimble fitted with rubber stopper through which passes a glass tube of 0.2-5-inch bore. Both tubes are connected by a short piece of rubber tubing. A section of a thimble is shown in the photograph; the tube extends to within in. of the tapered end. The object of using the thimble is to remove the acid from the beaker after all the copper has been precipitated. Time is saved, the copper is not exposed to the acid alone, and there are none of the losses attending ordinary filtration. I have accomplished these results by means of a piece of perforated platinum fastened in the end of a 0.25-in. bore glass tube and a filter-mat of asbestos, but after my supply of proper length fiber became exhausted I could not replenish it even after purchasing 14 lots from four different dealers. The above apparatus may be used to remove at least seven-eighths of a supernatant liquid from a settled precipitate without disturbing the latter. The application of the thimble is best shown by partly out-lining the assay for copper, as follows: Dilute the acid solution of copper and other sulphates to 150 cc. in a 200-cc. Jena beaker, place on a hot plate, add 2 drops of concentrated HC1, then place a strip of aluminum in the beaker (this may be bent or straight, as desired). Connect the apparatus, as shown in Fig. 1, with a filter-pump having a, strong suction. When the copper is precipitated, remove the beaker from tine hot plate and insert the extraction-thimble alongside the strip of aluminum. The acid solution will be drawn through the porous tube. Wish the upper end of the aluminum strip with a jet of hot water, wash down the sides of

Nov 1, 1912

By Thomas L. Kesler

I all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig. 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig. 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin. The Ocmulgee and Oconee rivers drain the area. They and their main tributaries have flat, swampy floodplains covered with alluvium and for the most part thickly wooded. The divides between these streams are intricately dissected by the minor tributaries, which are spring-fed in steep-walled, cirque-like heads. Gullying and under-cutting are active along the streams but are partly controlled by unusually dense vegetation. The mean altitude is about 350 ft above sea level, and locally the relief ranges up to 200 ft. The area is near the inner margin of the Coastal Plain, and is underlain by Cretaceous and Tertiary formations. Its general location is shown in black in Fig. 1. The division between the Coastal Plain and the Piedmont plateau is actually a very sinuous line, the fall line, marking the extent to which erosion has stripped the Coastal Plain sediments from the southeastward-sloping surface of the crystalline rocks of the Piedmont. Cretaceous Host Formation The kaolin deposits, which are described in the succeeding section, occur sporadically in lenslike bodies in a thick series of poorly sorted clayey sands constituting the lowermost of the Upper Cretaceous formations, the Tuscaloosa. The basis for this correlation has been reviewed by Cooke.1 The same formation has been termed the Potomac group by Ladd2 and the Middendorf formation by Smith' in reports on the kaolin deposits. In another report, Veatch4 called the formation the Tuscaloosa but correlated it with the Lower Cretaceous. The Tuscaloosa in this area consists of fine to very coarse sands, commonly cross-bedded, which contain widely different proportions of white, pink, and yellow kaolin and considerable white mica. A few of the coarser beds contain quartz grains up to 3 in. in length, with bodies of pure white kaolin of equal size that appear to have been formed by the weathering of feldspar grains in place. In the kaolin-producing area, gravel and cobbles occur mainly at the base of the formation. Fig. 2 shows the relations of the Tuscaloosa and its kaolin deposits to the adjacent formations. Its base, on the eroded surface of the crystalline rocks, dips southeastward 50 to 60 ft to the mile, according to LaMoreaux.5 The upper surface of the Tuscaloosa is also an unconformity,

Jan 1, 1952

By J. M. Gaines

THE use of oxygen in electric furnaces is relatively old, and the practice has been employed by several steelmakers prior to the recent impetus given generally to the use of oxygen in steelmaking. This application has been described recently in several publications,1 and a number of patents relating to the application of oxygen in electric furnaces have been issued.2 An effort is made in this paper to assemble recent information relating to the use of oxygen in electric furnaces and to present this material from a practical viewpoint, to an extent consistent with the withholding of certain operating data which manufacturers consider to be confidential. The use of oxygen has been extended during the past months in a number of additional steel companies by incorporating oxygen practice into regular production and by much increased experimentation. Available records show that oxygen is used more or less regularly at present in 18 shops, of which six utilize the oxygen for production and the others for experimen¬tation. The number of furnaces per shop using oxygen varies from one to six. Many types of electric-furnace steel have been prepared with the assistance of pure oxygen, including low-carbon and medium-carbon killed steels, low-carbon rimming steel and low-carbon and medium-carbon stainless and alloy steels. Oxygen has been used in furnaces of all sizes up to 90 tons capacity for accelerating charge meltdown and for reduction of carbon.

Jan 1, 1947

G. A. Moore—The tin-fusion method has been a very favorable possibility for many years. The authors apparently have settled the question that delayed the method for a long time by showing that no hydrogen is absorbed in the tin. This, of course, is very important. I want to make a few remarks concerning the absolute accuracy of analysis, which must be the final basis for deciding among the various methods. From the figures in the paper, there seems to be some re-maining slight discrepancy on the actual amount of hydrogen present in various samples which may be presumed essentially identical. (This is of the order of the precision of individual analyses but appears in averaged results.) From the analyst's viewpoint, the tally of hydrogen content can be regarded as occurring in three portions. First is a large portion which comes off easily and automatically during sample storage and later on heating in the apparatus. This is fairly easily analyzed. Second is an item which may be either positive or negative in the tally sheet. In warm or hot evolution, this is a portion which, in practice, can never be re-

Jan 1, 1951

By SAM YOUR

PROCESSING, technology and application of non- ferrous metals-copper, lead, zinc, aluminum, nickel, precious metals, foundry metallurgy, less common metals, secondary metals-are the special field of the Institute of Metals Division. New developments in this field during 1930 are more or less briefly out- lined in this review prepared by the papers and publications committee of the Institute of Metals Division as follows:

Jan 1, 1931

By Stanley J. Gasior, Albert J. Forney, Joseph H. Field

Most bituminous coal mined near Eastern industrial areas requiring high-Btu pipeline gas is caking and therefore unsuitable for fixed-bed pres- sure gasification by present techniques. If the caking property of such coal can be destroyed, the resulting fuel can be gasified in a fixed bed at pressure with steam and oxygen as a preliminary step in making a high-Btu gas. To find a practical way to convert strongly caking coals of granular or small lump size to noncaking fuel was the object of this study. In previous work, strongly caking coals of 1/8- to 1½ -in. size were converted to a noncaking coal char by treatment in a static bed in about 3 hours1 and coal of 18-100 Tyler mesh in a fluidized bed in about 5 min.2 An inert gas such as steam, nitrogen, carbon dioxide or a mixture of all three with a small amount of oxygen was used in both studies. In our work a strongly caking bituminous coal from the Pittsburgh seam of 4-8 Tyler mesh size was converted to a noncaking form in free-fall in about 2 sec by dropping it through a countercurrent flow of steam containing 4% to 7% oxygen at 1150º-1200°F and 300 psig. This method should also be applicable to smaller-sized material.

Jan 3, 1965

A. L. FIELD, Cleveland, Ohio (written discussion*.-)In equation 2, B is used to denote the ratio of bases (lime plus magnesia ) to acids (alumina plus silica) it being stated that this ratio gives more concordant results than the ratio either of bases to silica, or of lime to silica. I find, however, that, by making use of the ratio between true CaO (CaO by analysis minus sulfur calculated to CaS) to acids, equation 2 may he modified to agree with the observed facts within an average error of 0.0041 per cent. sulfur instead of 0.0045 per cent. The revised equation is s = 0.072 + 0.01835 - 0.00061 (t - 1400) - 0.0403B where B is the ratio of true CaO to Al2O3 Plus Si02, and the other symbols have the same significance as before. I would not appear to stress too much this slightly better agreement of the revised equation with the observed sulfur. Yet I believe that the use of this ratio of true CaO to acids is to be preferred, if for no other reason than the fact that it is more in harmony with the previous findings of the Bureau of Mines with regard to the effect of magnesia and other impurities on slag viscosity.1

Jan 12, 1919