Search Documents

By G. Bassi

RECENTLY Wallbaum¹ found that copper wires with different degrees of deformation up to 98.7 pct area reduction recrystallize giving a [112] texture, while deformation over 98.7 pct gives either a [l00] texture at low temperatures or a [1ll] texture at high temperatures. Furthermore it was found that the recrystallization temperature as a function of deformation up to 98.7 pct decreases as expected, but increases over that deformation. Wallbaum concluded that the different textures have different recrystallization temperatures. The [112] texture has the lowest and [Ill] the highest. At the same time Bassi² found that for high deformation (over 99 pct area reduction) and for an annealing temperature of 400°C, the [l00] texture first forms and with prolonged annealing time the [12] texture appears through grain growth. This secondary texture does not appear if the wire is annealed at 1000°C before the deformation. From these two papers it might be concluded that the [I12] texture can appear either as a primary or as a secondary texture after annealing. The texture formed in a special case depends on the previous history of the wire. Probably the texture of the wire prior to the last deformation is important. To investigate this, wires were produced by adequate deformation and annealing to give a [l00], a [112], and a [lll] texture. The wires then were given a series of different deformations and were annealed at various temperatures, after which the textures were studied. Experimental Work The copper used was electrolytic tough-pitch (Cu 99.90 pct and 0, 0.04 pct). Three wires with the different initial textures were made in the following way: The [l00] and [112] by drawing a 16 mm rod to 1 mm and annealing it 16 hr at 200°C and 2 hr

Jan 1, 1953

By John W. Tieman

Coal is a term applied to vegetable matter which, through geological processes of heat and pressure, has had both its physical and chemical properties changed. Because its chemical composition is variable, geologists classify coal as a rock rather than a mineral. Peat represents the initial stages in the development of coal, although not classified as coal itself. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness of coal determines the maintenance cost on coal handling equipment; the specific gravity of coal determines the coal preparation techniques used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent upon the chemical constituents that make up coal, and thus all properties are interrelated. Specific Gravity The specific gravity of a body is the ratio of the weight of the body in air and the weight of an equal volume of water. The specific gravity of pure coal ranges between 1.25 and 1.70, generally increasing with rank. The most important use of this physical characteristic is the part that it plays in the cleaning of coal by wet wash methods. The basic principle on which these operate is that the specific gravity of coals differs from their associated impurities and that there is a relationship between the velocity of the fall of particles in water and their density. Since the specific gravity of slate is around 2.5 and pyrite is about 5.0, pyrite and slate will fall to the bottom of a container filled with water more rapidly than coal. If the water is given a pulsating motion by

Jan 1, 1973

By Stephen Taber

JOHN C. BRANNER, Stanford University, Cal. (communication to the Secretary *).-Wideawake teachers of geology are constantly on the lookout for good illustrations of veins, especially where the processes of formation are either clearly shown or suggested. And I long ago found out that one who would learn nature's laws must despise nothing. It thus happened that in 1910, Dr. George J. Peirce of the depart-ment of botany at Stanford University called to my attention a cracked and broken yellow earthenware dish, 8 ½ in. across the top and 2 ½ in. deep, that, to the ordinary observer, seemed to be of no further use, and quite ready for the waste can. The striking thing about this dish was that the thin glaze over much of the outside surface and over the upper margin of the inside surface had been lifted in small scales, varying in. diameter from ½ cm. to 1 cm., and thrust outward and held there by some sort of white fibrous mineral. The process looked very much like one we are familiar with in the Southern States where. we often see in the winter pebbles and soil thrust out from a clay bank or lifted from a clay soil and held there supported by what is popularly known as needle-ice. Upon inquiry I learned the following facts in regard to the history of this particular dish: In the summer of 1910, it had been partly filled with a concentrated salt solution taken from one of the salterns of the Stauffer Chemical Co. at Redwood City, Cal. A qualitative analysis of the original brine showed: Present: iron, magnesium, sodium, potassium, chlorides, sulphates, nitrates (trace), bromides, carbonates, borates (trace), and considerable amounts of organic matter. Absent: calcium, lithium and iodides.

Jan 3, 1917

By Charles M. Rolker

It is now three years ago that I wrote a paper on the fire which broke out in October, 1880, at the Chrysolite mine, Leadville, Col orado, of which I was at that time manager. The paper was read by title at the Harrisburg meeting in 1881, and was accompanied by plans and sections fully illustrating it. It was written to invite a general discussion of the course pursued in the management of that fire, since the various fragmentary and sometimes prejudiced or inaccurate newspaper accounts were not suitable to base judg ment on. The paper I offered, gave the facts as they appeared in the contemporaneous record which I had kept. At that time, a dif ference of opinion had arisen with an adjoining mine, as to possible damages entailed through the fire; and a law suit was talked of. In view of these circumstances, the President of the Chrysolite Company advised a temporary withdrawal of my paper. Somewhat later, I withdrew it entirely, because of the unlooked-for delay in * arranging the controversy referred to. It. has now, indeed, been amicably settled; but the lapse of time has deprived the matter of much of its immediate professional interest. To the urgent request of some of the members, that I should, at least, give a description of the fire- and gas-proof bulkheads employed, I yield with some hesitation, since I lay no claim whatsoever to orig inality in these devices, and therefore question the value of such a paper. The fire originated by accident, in the Chrysolite, a mine comprising extensive and more or less irregular workings, containing immense quantities of timbering, but partially packed with waste rock or earth. This class of mines is numerously represented at

Jan 1, 1885

By J. Brian Eby

CONTACT metamorphism of coals is any physical or chemical change in the character of a coal directly attributable to heat of surface or intrusive igneous rocks. Coal beds so affected are found in the United States, England, Alaska, Mexico, New Zealand, Greenland, and other countries. Particularly in the United States, there is a wide occurrence of contact altered coals; conspicuous examples are found in Colorado, Utah, New Mexico, Illinois, and North Carolina. During a recent examination of coal beds on Yampa River, in north-western Colorado, the author had an opportunity to make some detailed observations on the contact metamorphism of coals. In this field, coals over an area of 20 sq. mi. have been affected by dikes, sheets, and sills;1 samples of the coals were systematically collected and analyzed,2 with the view of obtaining more specific data on the character of these alterations. The investigation was threefold in purpose: to secure information on the lateral effects of a dike cutting a coal bed, on the range in vertical effects on coal beds overlying sheets or sills, and on the range in the vertical effects on coal beds underlying sheets and sills. Favorable field conditions, such as fresh outcrops and newly dug prospects, made possible many of the field observations and collections. The coals studied in this field belong chiefly to the Mesaverde and Laramie formations. The Mesaverde coals, on the average, are blocky low-rank bituminous coals; the "Laramie coals," which are considerably younger, are of subbituminous rank. The coals of both formations, in the northeastern part of the Yampa field, have been greatly affected by basalt intrusives, yielding all variations of carbonized coal from natural coke to the unaffected material.

Jan 1, 1925

By R. E. Lindstrom, D. G. Peterson, H. J. Heinen

Alkaline alcohol solutions were investigated by the Federal Bureau of Mines for improving the desorption rate of gold and silver from metal-laden activated carbon generated in gold processing circuits. Factors affecting the desorption, such as temperature, alcohol content, type of alcohol, and alkalinity, were studied. Nearly complete metal desorption was obtained in 5 to 6 hr at 80º C using a solution containing about 20 vol-pct alcohol and 1 pct sodium hydroxide. Sodium sulfide was shown to be effective for selectively precipitating silver from the carbon strip solutions, thereby providing a means for producing high- purity gold by subsequent electrolysis.

Jan 1, 1976

By J. A. Musselman, J. B. Cheatham

In recent years considerable effort has been expended in the search for new ways of drilling into the earth's crust and for improvements of existing methods. A number of novel techniques have been explored such as explosive, flame, electric arc, abrasive jet, chemical, and various percussion-type dri1ls.l Some of the new methods are useful in isolated situations, but rotary drilling continues to be the most versatile and generally economical method for rock drilling. An understanding of rock failure during drilling can lead to improved rotary drilling techniques and to the development of new methods. Experiments 2-4 have shown that rock strength and ductility increase with increasing pressure; therefore, meaningful experimental investigations should be carried out under conditions similar to those encountered at the depths to which oil wells are drilled. The action of a roller-cone bit is not pure rolling in all cases but frequently involves gouging and scraping action. However, vertical penetration of a horizontal rock surface by a single punch has served as a first approximation of the rock/bit tooth interaction during drilling.5,6 In these experiments semi-infinite smooth rock surfaces are indented by steel tools with configurations having various degrees of dullness. Both static and dynamic tests have been investigated; however, static loading provides a good approximation of the loading rates occurring during rotary drilling. As a more realistic approximation to actual drilling conditions, chip generation must also be considered. Recently, studies have been made of indexing or chipping from a bit tooth to a previously formed crater.7-9 The purpose of the present investigation is to study indexed penetrations in greater detail. Fig. 1-A illustrates the general problem. Pittman and Cheatham 10,11 have used plastic limit analysis to study the idealized plane-strain indexing problem for a material having a linear Coulomb-

Jan 1, 1972

By Douglas W. Fuerstenau, Kalanadh V. S. Sastry

Mathematical considerations of green ball growth in a balling device by the mechanisms of layering new feed onto seed or recycle pellets are presented. An experimental procedure was developed for investigating the agglomerate growth by layering in which the addition of feed to a batch of seed pellets was made cyclically. Using this procedure, the layering growth mode under partial feed consumption and no seed generation conditions was investigated experimentally in a laboratory balling drum as a function of such operating variables as moisture content of the material, feed rate, and the size distribution of the seed pellets. The experimental results were analyzed in the context of the model equations and the layering growth constant was estimated as a function of the operating variables.

Jan 1, 1978

By W. Joseph Schlitt

The types of copper leaching and recovery operations in the United States are reviewed, along with characteristics and trends in the industry. The contribution of the various leach operations to total mine output is discussed in order to provide a perspective on the relative importance of copper leaching as a method of production.

Jan 1, 1980

By Albert McIntosh

One of the most interesting as well as important factors connected with the petroleum industry is the consumption of motor fuel. A few years ago we always spoke of "gasoline," but when natural gasoline and benzol became more important it seemed desirable to include all of these products in the petroleum statistics and so there was adopted the term "motor fuel," which embraces these three products in their entirety. Gasoline always included all stove and motor gasolines, high-grade naphthas, cleaning naphthas, solvents, varnishmakers' and painters' naphtha and gas-machine gasoline. "Motor fuel" includes all of these products also; therefore, technically the term "motor fuel" is incorrect, but as the total quantity of these non-motor naphthas is small their inclusion does not distort the results to any appreciable extent. When the Federal Oil Conservation Board appointed its first semiannual forecasting committee early in 1930 to project the demand for gasoline and crude oil into the year 1930, it was necessary for that committee to formulate a method of forecasting. It adopted the system in use by some of the oil companies at that time, of using automobiles and per-car consumption. Six months later the American Petroleum Institute also formed a committee for forecasting, which adopted the committee principle of asking each member to produce his own forecast of demand by any method he thought best and to give a full explanation to the committee. The result of the latter method was to get the benefit of as many different methods of forecasting demand as there were members. The writer does not recall any two members ever using exactly the same method. By studying the different forecasts and their methods, there evolved a composite opinion, which was presented to the industry as the committee's estimate. The same method has been followed by the American Petroleum Institute or Planning and Coordination Committee ever since.

Jan 1, 1935

By Morris Cohen, William P. Kimball

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expression for the composition (6) of the liquid-to-solid transfer at each temperature has been derived: d= Zlxl(xl - P) + Zsxs(P - xs)/Zl(xl - P) + Zs(P - xs) [1] where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, Xl and 28 are the compositions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under consideration. The 6 equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid- to-solid transfers if the corresponding equilibrium diagrams are known. The d-versus-temperature curves for two alloys P1 and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid phase only at the temperature of the beginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate temperature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling, the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1941

By William P. Kimball, Morris Cohen

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expression for the composition (6) of the liquid-to-solid transfer at each temperature has been derived: d= Zlxl(xl - P) + Zsxs(P - xs)/Zl(xl - P) + Zs(P - xs) [1] where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, Xl and 28 are the compositions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under consideration. The 6 equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid- to-solid transfers if the corresponding equilibrium diagrams are known. The d-versus-temperature curves for two alloys P1 and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid phase only at the temperature of the beginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate temperature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling, the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1941

By T. R. Young, S. A. Scott

9.5-1. Introduction. The use of pipelines to transport solids has been successfully accomplished with many different materials. One of the oldest applications is the dredging and placing of hydraulic fill. Many installations have been made and operated for long periods of time with excellent dependability, low operating cost, and low maintenance. It is not the aim of this chapter to give the engineer the answers from which to design a pipeline, but rather to supply helpful information from which to start the project. There are several phases of solids pipelining which as yet have not lent themselves to quick engineering answers. Investigations have been carried on by many, with several theories advanced by the various investigators. In recent years certain notable theoretical advances in hydraulic transportation have been achieved. Vertical transport, using balanced "leg" operation, now appears competitive with other forms of vertical transportation. In addition, horizontal transport utilizing capsules has been proven experimentally to be attractive because of lower pressure drop than the conventional methods of solid transport in fluid media. With the aid of the computer, the laborious calculations associated with pumping calculations have been greatly simplified; and with this tool the pipeline engineers of the future will undoubtedly be able to develop a more comprehensive understanding of solids-fluid transport. 9.5-2. Theory. There have been many excellent studies made and information is available in the literature, but a general comprehensive theory of pipeline transportation of solids has not been advanced. The existing flow theories will give approximations for minimum and optimum flow velocities, friction head losses, energy requirements, and pump and pipe size The principles of dynamic similarity and scaling laws are well understood for the flow of pure liquids. There are no firm methods of scaling slurry pipelines of small diameter to larger diameters except for a few empirical.

Jan 1, 1968

By R. I. Williams

Kennecott Copper's mining activities in Arizona are conducted by the Ray Mines Div., located in Ray, Ariz., in the Mineral Creek mining district about 60 miles southeast of Phoenix. The Ray orebody lies in a mineralized zone belted on the east, west, and north by well defined faults. The orebody consists principally of schist with intrusions of quartz porphyry and diabase. The dominant ore mineral in the schist and quartz porphyry is chalcocite, with some native copper, and in most areas the orebody has been heavily oxidized. In the diabase the dominant ore mineral is chalcopyrite. Ore deposition in the schist portion is very erratic, with no apparent structural explanation. In 1873 silver prospectors opened the mining district, but it was not until 1899 that an English company made the first major attempt to exploit the copper deposits. This venture failed because of improper sampling and limited development work. In 1904 D. C. Jackling, Seeley Mudd, and Philip Weiseman became interested in the Ray Copper Co. and the Gila Copper Co., which later merged as Ray Consolidated Copper Co. In 1926 the Nevada Consolidated Copper Co. took over Ray Consolidated and in turn was taken over by Kennecott Copper Corp. in 1933. The extensive program of surface and underground development and exploration begun in 1907 continued through successive changes of management and ownership to the present time.

Dec 1, 1956

G. F. COMSTOCK (author's reply to discussion *).-The discussion of this paper has been of such volume and interest as to constitute in itself a sufficient excuse for the paper, even though the paper itself may have been as much in error as some of its critics have maintained. Mr. Howard does not appear to realize some very practical facts that the opponents of his theory have advanced. Among these are: the coarsely crystalline fracture of the nucleus of a transverse fissure, so different from the smooth fatigue break around it; the occurrence of fissures in large numbers in certain heats or rollings of rails, while other heats or rollings do not develop them; and the much smaller proportion of transverse fissures found in rails rolled .from reheated blooms as compared with direct-rolled rails. These facts are not explained by Mr.

Jan 6, 1919

INSTITUTE MEDALS AND PRIZES ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as fol¬lows. the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saun¬ders Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony-on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules 1 The award shall consist of two prizes first of a gold medal, second of a sum of money, a certificate to accompany each prize The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material

Jan 1, 1923

EDWARD W. PARKER,* Philadelphia, Pa. (written discussion ?).-The two papers on coal-mine costs and pride fixing that Mr. Norris has contributed to the Transactions possess as much general interest and are of as much value to the coal-mining industry as any papers that have been presented in recent years. Until recently one of the troubles with the coal business, and especially the bituminous branch of it, has been that because of the lack of a uniform system of cost accounting (many operators, I regret to say, not having had any system at all), the industry as a whole may be said not to have known where it was at. The system adopted by the Federal Trade Commission may not be absolutely perfect but it has accomplished something in that it has compelled a uniform method of reporting and tabulating costs giving results of these compilations which are comparable. The Institute and the coal-mining industry owe a vote of thanks to, and of confidence in, Mr. Norris and his two associates on the Engineers Committee of the Fuel Administration, Messrs. Garnsey and Allport, for the great work they have done in interpreting the results compiled by the Federal Trade Commission, not to speak of the personal sacrifices made by them in giving their services to the government. Those who have read Mr. Norris' paper will probably join me in wishing he had brought out a little more fully the real meaning of the charts so far as they indicate the difference between the cost of producing a ton of anthracite and the price the operators receive for their product. Mr. Norris could have done this more satisfactorily than anyone else. It seems to me that particular attention should be drawn to the fact that, according to these charts, and the tables accompanying them, not less than 25 per cent. of the total output of anthracite, whether "company" or "individual," during the period covered by Mr. Norris' paper,

Jan 4, 1919

A. V. ADAMSON,* New York, N. Y. (written discussion).-The experience of users of pulverized fuel in metallurgical work, particularly for open-hearth furnaces, has demonstrated that high ash and sulfur in pulverized fuel are a detriment, the sulfur in the coal entering into the finished product; hence, in this class of work it is extremely important, when pulverized coal is to be used, that the coal be selected with care, and only those having low percentages of sulfur be used, in combination with proper means for combustion. I have found that no general statement can be made as to the cost of pulverized coal, each installation being an individual engineering problem and necessitating a varying capital expenditure; as each installation has its own power cost, the actual cost of pulverizing varies between wide margins. It has been found that no general rule can he laid down as to either fineness or dryness; for some uses a wide range is permissible in both factors, while some classes of fuel require different treatment from others. Anthracite, coke breeze, and lignite ash will, under certain conditions, form slag, the melting point of the ash from fuel of this character being practically the same as of that from bituminous coal; furnace temperatures above the melting point of ash must therefore cause the formation of slag. However, it should he noted that furnace temperatures attainable with this class of fuel are not usually so high as those from bituminous coal, which probably explains the statement that the former do not slag. In a well designed furnace, temperatures above 2250° F. (1235° C.) will be obtained with that class of fuel, and slags will be formed. Too much attention apparently has been centered on high CO2 contents of stack gases. A high percentage of C02 is frequently obtained at the expense of the brickwork, the furnace temperature being increased by diminishing the excess air; a high percentage of C02 thus simply means a small proportion of 02.

Jan 12, 1918

Jan 1, 1917

By R. R. Seeber

In the copper-mining district of northern Michigan a fair-sized mine usually operates two or more shafts along the strike of the lode, these shafts being usually at least 1,000 ft. apart. The tonnage to be hoisted from each shaft is large—from 13,000 to 25,000 tons per month. The hoisting-engines used are generally steam-driven, non-condensing, duplex engines with Corliss valves, supplied by steam from separate boiler-plants where the distance between shafts is great. In an attempt to centralize power-plants and secure central-station economies, the Winona Copper Co. installed an electric hoist of the Ilgner type, with Ward Leonard control. A brief description of this plant has already been published.' The only point of variation from the simple Ilgner set lies in the connection of two generators to a single induction-motor by flexible couplings. These generators serve motors which operate hoisting ing-drums at separate shafts, viz., No. 4 shaft, Winona, and No. 1 shaft, King Philip. The hoist for No. 4 shaft is about 1,700 ft. from the power-plant, arid in this building the motor-generator set is placed. No. 1 King Philip hoist is 1,500 ft. from the motor-generator set. The equipment of the motor-geaerator set is as follows: In the middle of the set is a 12-pole, 450-h-p., 600-rev. per min., 2,080-volt, three-phase, 60-cycle, variable-speed induction-motor, connected on each side to a 20-ton fly-wheel which is 10 ft. in diameter, and to a 6-pole, 170-km, 575-volt, interpole, direct-current generator. On each side of the shaft is placed a separate exciter, which delivers current at 125 volts. The lubrication of the four main bearings that support the fly-wheels

Jan 1, 1911