Search Documents

By R. C. Ferguson, Harlowe Hardinge

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year's time. THE object of this paper is to show the economic advantage of operating ball mills at relatively slow speeds. Although many operators know that grinding costs are reduced by operating mills at low speeds, they seldom do so for a variety of reasons. When capital is limited, first cost is of primary importance, and installation of the less costly, highspeed mill is favored. When materials are in short supply, as during a war period, capacity rather than economy is the primary consideration. Existing mills are then speeded up to provide the desired increase in capacity, and new mills are purchased without consideration of maximum grinding efficiency. When the mill speed is increased to secure more production, the increase in grinding costs is often obscured by the total benefit derived from the additional output. This increase in grinding cost is seldom recognized as being sufficient to be worth correcting. For these reasons one may be lead to the erroneous conclusion that slow-speed operation is only occasionally applicable. The effect of mill speed on grinding efficiency has been studied in laboratory tests."! The results of some of these tests are given in tables I and I1 and fig. 1. In these tabulations, batch tests using ore charges of 125 to 200 lb were considered comparable to high pulp-level operation and charges of 50 to 100 lb comparable to low pulp-level operation. For the high pulp-level operation, these tests indicate the existence of a maximum in efficiency for operation at a speed of 50 pct of critical, both for the soft (dolomite) and hard (chert) ore. In low pulp-level operation, a decrease in speed increases the efficiency of grinding dolomite; no maximum of efficiency appears in the range of speeds tested. The results with chert were inconclusive. If the performance of large mills is indicated

Jan 1, 1951

By Harlowe Hardinge, R. C. Ferguson

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year's time. THE object of this paper is to show the economic advantage of operating ball mills at relatively slow speeds. Although many operators know that grinding costs are reduced by operating mills at low speeds, they seldom do so for a variety of reasons. When capital is limited, first cost is of primary importance, and installation of the less costly, highspeed mill is favored. When materials are in short supply, as during a war period, capacity rather than economy is the primary consideration. Existing mills are then speeded up to provide the desired increase in capacity, and new mills are purchased without consideration of maximum grinding efficiency. When the mill speed is increased to secure more production, the increase in grinding costs is often obscured by the total benefit derived from the additional output. This increase in grinding cost is seldom recognized as being sufficient to be worth correcting. For these reasons one may be lead to the erroneous conclusion that slow-speed operation is only occasionally applicable. The effect of mill speed on grinding efficiency has been studied in laboratory tests."! The results of some of these tests are given in tables I and I1 and fig. 1. In these tabulations, batch tests using ore charges of 125 to 200 lb were considered comparable to high pulp-level operation and charges of 50 to 100 lb comparable to low pulp-level operation. For the high pulp-level operation, these tests indicate the existence of a maximum in efficiency for operation at a speed of 50 pct of critical, both for the soft (dolomite) and hard (chert) ore. In low pulp-level operation, a decrease in speed increases the efficiency of grinding dolomite; no maximum of efficiency appears in the range of speeds tested. The results with chert were inconclusive. If the performance of large mills is indicated

Jan 1, 1951

SULPHUR is a very well known mineral and apparently is produced in many places. It is engendered from an unctuous earthy and powerfully hot substance so that it is considered among experienced workers to bear a resemblance to the element of fire. This is called by these same men the masculine seed and the prime agent of Nature in the composition of metals. Because of its great dryness and heat it has, as experience shows, affinity with fire, which is easily introduced in it when brought near. And once introduced the fire is quenched only with difficulty before its unctuousness is wholly consumed. Although it shows itself to us of such a hot and dry nature, we must not think that sulphur is a substance so pure that it can stand by itself or that in order to attain its form it has no need of its portion and part of moisture like every other mixture. This is shown to us by its easy fusion, in which it resembles the metals. This thing is found in many places and in many varieties of color; some are white, others yellow and orange, and some others between gray and black. They also say that some red is found. It does not occur in that arrangement of veins like other minerals, but most liberal Nature makes whole mountains of it as is seen in the Aeolian islands, [26] near Sicily, in Etna or Moncibello which is the island of Sicily, at Pozzuoli, in the territory of Rome, in the Sienese domain at San Filippo, and in many other similar places. It is a substance that has a very strong odor and is most unpleasant to smell. It is very fixed in its substance so that it is never corrupted by time, by boiling, or by the moisture of water. For although it may stand in water a long time it never becomes soft nor does it ever decrease or increase in weight. It is brittle and easily crushed very fine. It is said that a trace of garlic rubbed on the mortar helps anyone who wishes to reduce it to impalpability. Its ores have a form more like earth than like stone although they some¬times have the color of a certain soft rock. The places where it is found are easily recognized by the great odor that they give out and by the very hot baths that often spring forth near it. What I have already told you about quicksilver that is contrary to the

Jan 1, 1942

By Blair R. Benner, Ronald J. Roman

The rate of acid leaching of malachite from a sandstone ore was shown to be controlled by the diffusion of H+ ions through the host rock. The kinetics of the reaction can be expressed by a shrinking core model. Equations for calculating effective diffusivities from an "infinite" slab and a cylindrical core were derived. The effective diffusivity, of H+ ions in a sandstone ore was measured.

Jan 1, 1975

By The Staff of Dames & Moore

Five factors are required for the formation of uranium deposits: a source, transporting medium, host, trap, and preservation. Locating and evaluating uranium deposits requires ail integration of methods and techniques to determine if the above factors are present. A typical exploration program consists of selection of a favorable area, field reconnaissance, land acquisition, and target definition and evaluation. Target definition and evaluation utilizes a combination of geologic mapping, geochemical surveying, geophysical surveying, and drilling and logging. Each overlaps the others to some degree.

Jan 10, 1978

By H. R. Skewes

IN the course of small seale experiments on the electrodeposition, of copper, extremely brittle deposits were obtained from electrolytes prepared by leaching calcined chalcopyrite with aqueous sulfuric acid. It was not possible to strip the metal without fracture after it had been deposited from such electrolytes onto smooth oiled copper sheets, the usual plant procedure for the production of so-called starting sheets. The embrittlement did not occur with electrolytes made either by leaching the calcine with water or by treating an acid leachate to remove iron as hydrous ferric oxide. The electrolytes which produced brittle deposits were found to contain molybdenum in concentrations of 10 to 25 mg per 1, whereas those which produced ductile deposits contained <0.5 mg per 1. Synthetic electrolytes having the composition: Cu", 40 gpl; Fe", 0.5 to 1.0 gpl; Fe3+, 0.5 to 1.0 gpl; and H,SO,, 10 to 50 gpl, were prepared from reagent-grade salts; by adding ammonium molybdate, the embrittling effect of the higher concentrations of molybdenum (VI) was strikingly confirmed. The brittle deposits contained up to 0.03 pct Mo. The importance of oxidation state of the molybdenum was demonstrated when the electrolyte containing it was circulated continuously through a bed of fine copper metal during deposi- tion. Under these reducing conditions, the cathode deposit was ductile and molybdenum could not be detected. Molybdenum has not been recognized as one of the metals causing embrittlement of copper nor is it listed among the usual impurities. In most elec-trowinning plants there is a purification step which removes iron from the leachate before electrolysis. In these cases molybdenum would be coprecipitated with hydrous ferric oxide. In the case of the large leaching plant at Chuquicamata, Chile, where the leachate is reported to contain considerable molybdenum, it would be reduced to a lower oxidation state during removal of chlorine by means of cement copper. This may explain why the embrittling effect of molybdenum has not been reported previously. Moreover, in copper refining plants where soluble anodes have been prepared by a high temperature smelting process, it is most unlikely that any molybdenum would remain with the copper, whereas the calcines in this work were prepared in a fluidized bed reactor at a temperature not exceeding 720°C. Acknowledgment This work is part of an investigation on the roasting and extraction of copper from sulfide ores sponsored jointly by Mt. Morgan Ltd., Queensland, and the Mt. Lyell Mining and Railway Co. Ltd., Tasmania.

Jan 1, 1958

By C. H. Aldrich

For many years the City of Prescot, about 8 miles northeast of Liverpool, has been the home of British Insulated Cables, Ltd., one of the largest wire mills and manufacturers of electrical equipment in England. Since this location is close to the industrial center of the country and the seaboard, with good railroad transportation facilities, it was a logical site for the new refinery. Early in April, 1932, the writer was called upon to prepare a preliminary layout and estimate of cost of the proposed plant, and shortly afterward, following a discussion of these figures with officials of British Insulated Cables, in England, the decision was reached to proceed immediately with construction of the plant. The refinery was built by British Insulated Cables, Ltd. Designing of the plant was started early in May, 1932, orders for equipment being placed as rapidly as possible. On July 18 the first steel was erected and the first charge was cast on Jan. 5, 1933. No difficulties of any consequence were experienced in starting the plant and the grade of copper produced was quite satisfactory after the first charge. The initial capacity desired was 2500 tons of refined copper per month. Since only one furnace was to be built, it was necessary that it should have sufficient reserve capacity to catch up after unavoidable shutdowns. It was also necessary to lay out the plant so that it would operate efficiently at this tonnage and at the same time permit expansion in the future, if necessary, to several times its original capacity. In order to meet these conditions and also to take full advantage of the space available, the layout shown in Fig. 1 was adopted. The principal plant structures are a blister storage aisle, casting building, wire-bar storage building and a coal-pulverizing building. Additional smaller structures include a brick and charcoal shed, pumphouse, drill room, water-cooling tower, clay-preparation shed, substation and plant office. Incoming blister is received in either broad-gage railway cars or steam motor lorries in the blister storage aisle, unloaded by overhead electric crane to narrow-gage cars, weighed and sampled, then either sent directly to the furnace or placed in storage. After refining, the copper is cast on the wheel, passes through the cooling bosh and is

Jan 1, 1934

By STEPHEN L. GOODALE

THE question indicated in this title was put by letter to a number of my friends working in various industries, who have charge of young metallurgical graduates. The replies were almost unanimous in stating that the college training should cover in the most .thorough manner possible those sciences which are the fundamentals - of engineering. Mathematics, physics, mechanics, electricity, chemistry, physical chemistry, and their applications to actual problems of life were mentioned in most of the letters I received. Some writers added also business law, economics,. and finance. One reply expressed it: "These subjects, well founded, mixed with good judgment, well applied, should enable the .young man to carry on the art of life successfully." One answer stated frankly what is really wanted: "As much as possible.&apos; &apos; This writer mentioned .the sciences as being very important, but he wishes men &apos; to be trained in metallurgy also, and he concedes the omission of some advanced chemistry and physic&apos;s to secure the metallurgy. He emphasized particularly. the a we. desirability of work in college to development&apos; He concludes his letter with a repetition of his slogan that what is wanted is as much as is possible.

Jan 1, 1930

Dr. Robert Bell died on June 18, 1917, at Rathwell, Manitoba, in the seventy-seventh year of his age. He was born in Toronto on June 3, 1841, and was a son of the Reverend Andrew Bell of the Free Church of Scotland. He was educated at the Grammar School of the County of Prescott, Ontario, and subsequently at McGill University and the University of Edinburgh. While still a boy of 15 years of age, he joined the Geological Survey of Canada, under Sir William Logan, in the capacity of Junior Assistant, and was rapidly promoted in the service, where lie remained-with but one short interval-for over fifty years, retiring as Chief Geologist and Acting Director in the year 1908. He married Agnes, daughter of the late Alexander Smith, of Westbourne, Glasgow, and Auchentroig, Stirlingshire, and is survived by one son and three daughters. Practically nothing was known of the geology of Canada, and very little with reference to its geography, when Mr. William E. (afterward Sir William) Logan was called upon to undertake the organization of the Geological Survey of Canada, and as its first Director to carry out the mapping of this vast area and the examination of its mineral resources. Dr. Bell&apos;s work as a member of Sir William Logan&apos;s staff in these early years consisted, therefore, exclusively of geological reconnaisance and geographical exploration. Even in later years, and until his administrative work confined him to his office, Dr. Bell&apos;s work remained essentially of this character. The exploratory traverses and track surveys which lie carried out were, chiefly within the area of the great Laurentian protaxis or Canadian Shield, which forms such a striking feature and which has played and will continue to play so important a role in shaping Canadian history and in influencing the character of the Canadian people. Dr. Bell&apos;s lines of exploration crossed and re-crossed this area from the Atlantic Coast to the Great Lakes on its western border, and from Lake Huron and Lake Superior on the south to the Arctic Sea, following the water ways of this great land. He also worked along the coast line when acting as geologist and naturalist to the "Neptune" Expedition in 1884, and to the "Alert" Expedition in 1885, both of which carried out explorations in Hudson&apos;s Bay and Hudson&apos;s Straits; also on the "Diana" Expedition in 1897, when he surveyed the coast of Baffin Land, and was one of the first white men who penetrated to the great &apos;lakes in the interior of that immense

Jan 11, 1917

By A. L. Labbe

SOON after the Cottrell treater was placed in operation in the Murray plant in 1918 to treat combined lead sinter and Wedge roaster smoke, it was noticed that the power flowing through the treater did not remain constant. This was indicated by the varying milliamperes and also by the total amount of power consumed by the rectifiers. At times, for then unknown reasons, the treater current fluctuated through a wide range of from 40 to 300 milliamperes. Fortunately, these variations in power did not affect the treater&apos;s overall recovery, as this installation consisted of three independent units in series, a feature which made the Murray Cottrell an outstanding installation over many years of operation. Water conditioning of the smoke as a means of improving recovery was already known, but was not adaptable to this installation for reasons of excessive corrosion, which had been the case with other treaters using water as a conditioner exclusively. Tests conducted on the smoke had proved conclusively that water vapor played no part in the fluctuation of power, and the same was true of the SO2 contents and dust burden of the smoke. Neither did temperature variations of from 150 to 400°F have any effect on the power. Finally it was noticed that the variation in power taken by the treater, and the efficiency of recovery, had some definite relation to the number of Wedge roasters operating, and particularly to the sulphur contents of the charge. This observation soon led to the discovery that free sulphuric acid was the conditioner for Murray smoke and that variations in acid contents of smoke accounted for fluctuations of treater power. Analysis of recovered dust revealed that only a few hundredths of a per cent free acid was necessary to maintain a very efficient recovery. Once this knowledge was available, the roaster charge was adjusted as to sulphur contents to produce the necessary acid conditioner. For a number of years this practice was followed, but with improvements in the field of flotation, excess pyrites were eliminated from the smelting picture, so with a change in metallurgical practice we were confronted with the problem of providing the deficiency in acid by some other means. The situation was aggravated and our problem of acid conditioning made more difficult by the increase in the lead contents of concentrates roasted resulting from better flotation methods. The first step towards introducing acid vapors into the smoke stream by accessory means was accomplished by boiling sulphuric acid in cast iron pots placed in an open fire box. Acid fumes evaporated from the pots together with the combustion gases from the fire box were discharged into the flue through a cast iron pipe. Capacity of the iron pots was quite limited because of the comparatively slow rate of evaporation and the use of lump coal as a fuel, which did not lend itself to practical temperature control. This method of firing resulted in frequent pot failures due to overheating. In spite of these incidental difficulties, encountered in any new venture, the pot evaporator demonstrated the practicability of fuming sufficient acid to make up the deficiency in that naturally evolved in the Wedge furnace operation. As time progressed, less and less high sulphur material was available for Wedge roasting, and the necessity for accessory acid conditioning reached a climax when the supply of this material was entirely eliminated. Since the cast iron pots could only evaporate a few hundred pounds of acid per day, and were costly to replace, the logical thought presented itself of spraying the acid in a heated chamber. This new type of acid evaporator was simpler and more economical to operate and had sufficient capacity to fume several thousand pounds per day. The attached fig. 1 presents the outstanding features of the new furnace. A is the vaporizing drum, which is heated by the combustion gases of coal stoker fire box, B. Acid is sprayed into the hot gas stream within the drum through a number of air-acid atomizers, C, and the acid vapor, together with combustion gases, is introduced into the smoke stream through two cast iron pipes extending to different points in the flue. The operation of this type of furnace requires control of temperature inside the drum to prevent overheating, which dissociates the acid vapor to SO, and eventually to SO2, with resulting loss of acid. The dissociation to SO, at elevated temperatures is comparatively high, and in some cases accounts for as much as 60 pct of the acid sprayed into the drum. To reduce the loss of acid, through dissociation, some Cottrell plants, where the rate of acid sprayed reaches at times 9 ppm, use two evaporating units. Fuming the acid into the smoke stream is only

Jan 1, 1951

Jan 1, 1964

By B. E. Hoffacker, R. E. Lund, J. Ferrighetto, G. E. Welch

Since October 1965 the Josephtown Smelter of St. Joseph Lead Co. has commercially applied the Heavy Media Separation process to reclaim zinc and reject gangue from electrothermic zinc furnace residues. In addition, heavy medium is produced from the ferrosilicon which is present in the furnace residues. By way of background, the Josephtown Smelter produces zinc metal and zinc oxide by the electro- thermic process. The principal feed to the vertical shaft electric furnaces is sized sinter and coke. Temperature of the charge in the furnaces varies from roughly 900°C near the wall to 1300-1400°C in the central regions. Zinc smelting is rapid and nearly complete in the main body of the charge, but little zinc is smelted near the wall. In addition to fusing high gangue content particles, the high temperatures promote side reactions, the most important of which is reduction of iron oxide and silica to form a low grade ferrosilicon containing about 82 % Fe and 13% Si.

Jan 12, 1968

By R. D. Reiswig

An increasing amount of high-temperature metall~?~gical research is carried out in resistively heated tube furnaces in which a bare specimen is suspended by a fine wire at the midpoint of the tube. It is shown that the assumption of near-blackbody conditions on the surface of the sample may give rise to errors in optical pyrometry of 50°C or more. A number of papers published in the metallurgical literature in recent years have described the use of high-temperature tube furnaces for heat treatments, melting-point determinations, and other work. Typically, the tube is of a refractory metal with open ends, is heated by the passage of an electric current, and has concentric cylindrical radiation shields outside it. In at least one of these,&apos; the specimen is contained within a crucible having a small hole in its lid through which optical-pyrometer measurements are made under essentially blackbody conditions. In another design,* the specimen is inside a muffle which is concentric with the heater tube and which contains a number of washerlike longitudinal radi- ation shields to reduce axial temperature gradients and to give conditions near the specimen closer to those of a black cavity. Yet another design3 employs a wire specimen coaxial with the heater tube. Blackbody conditions are simulated by passing current from a separate supply through the wire until it "disappears" against the background (the inside of the heater tube) as seen through a radial spy hole in the tube. Good agreement with known melting points is achieved when an optical pyrometer is used under such disappearance conditions as the melting point is approached. That this latter method works so well is due, evidently, to considerations such as those mentioned by Dike4 and others.5-8 A more common method than the above, however, has been the suspension of an uncovered specimen by a fine wire in a resistively heated tube with open ends. A radial spy hole about midway between the ends of the tube permits optical-pyrometer observations on the specimen, the inside of the tube, or both. So observed, the specimen typically appears to differ but little in brightness temperature from the inside of the tube. According to De vos9 the radiation from such a spy hole in an empty tube of reasonable 1ength:diameter ratio (e.g., 10 or greater) should be essentially blackbody radiation. For these reasons, apparently, descriptions of work carried out in such furnaces usually include a statement to the effect that conditions surrounding

Jan 1, 1964

By Peter J. Maxworthy

INTRODUCTION There is no hard and fast rule on whether functions within a company, diversified or otherwise, should be strongly centralized or decentralized. In all diverse organizations, there are certain basic functions which remain common (or central) to each element of the business, viz: Personnel Management Cash Management Taxation Management Legal Planning Accounting Standards It would follow that each of these common factors requires some supervision at a central level to ensure that overall group objectives are met. It is true that other functions including: Industrial Relations Marketing and Distribution Production Research and Development Purchasing Management Accounting may also be common to each element of the organization. However, there is far less commonality in the degree to which these functions are central to the efficient performance and financial well-being of the business. Role of Operating Units The resources of operating centers may be viewed as a bank of funds, the nature of which can be changed from time to time, but the employment of which must provide for ongoing increases in the net worth of the total enterprise expressed in terms of market values. Operating units are required to continually review products, methods, and opportunities and to monitor avenues for incremental investment--all with a view to attaining the necessary additive net present value of future cash flows of the enterprise. Operating units should be permitted sufficient autonomy to enable the best use to be made of the skills and experience of the people it employs in order to produce a return appropriate to the value of assets employed. Role of Head Office The head office will typically comprise a specialist group--the leaner the better if one strongly adopts the decentralist approach--often acting as Service Centers but also performing a control function in the corporate sense. The head office function is a cost center. It may be instrumental in developing strategies for increasing revenues or reducing costs on a group scale, but it does not generate revenue. Every dollar spent on this function is an extra dollar to be generated by the operating centers in order to achieve an increase in corporate wealth. TREASURY MANAGEMENT Treasury management is concerned with the provision of finance, cash-flow management, and risk analysis. Each decision taken within the enterprise has a cash implication. It follows that a well-integrated central Treasury function can, in all likelihood, produce economic benefits. The degree to which the function should be centralized depends largely upon the unique nature of the operating units it is servicing. Levels of ownership, the calibre of unit operating managers, and the nature and geographic distribution of the business are all factors determining the degree to which the Treasury function is centralized. In the case of Peko-Wallsend, the Treasury Department is small, comprising four people. While divisional cash-flow management is largely decentralized, Treasury is responsible for the daily management of funds surplus to the immediate needs of operating units. Treasury also operates as central banker and provides funds to

Jan 1, 1985

C. A. HANSEN (communicated appendix*).-Since the above paper was written, tests have been conducted with a view to securing a sounder basis for discussing the effects of temperature on the behavior of the zinc cell. The following data, while making no pretense to great accuracy, are still reasonably close. Cells were operated with the same feed solutions, but at varying temperatures, the latter being controlled by means of immersed steam coils. Current efficiencies obtained indicate that the corrosion rate

Jan 11, 1918

By Bryon W. Cheever

The greatest objection to be brought against the present methods for estimating phosphorus in iron and steel, is the time consumed in the operation. The following method, originated and perfected by Mr. E. D. Campbell, assistant in the chemical laboratory of the University of Michigan, will, 1 think, if carefully followed out, give results that are sufficiently accurate for technical purposes, and will give them in less time than they can be obtained by any other process. The process consists in comparing the color obtained by the action of stannous chloride upon a solution of the phospho-molybdate precipitate obtained from the solution of iron or steel, with that obtained from a standard solution of molybdie acid which represents a given amount of phosphorus. The operation is as follows : Take of ordinary steel 1 grm. and treat as in any of the wellknown processes until the phosphorus is precipitated as ammoniumphospho-molybdate. When precipitated, the phospho-molybdate precipitate is filtered out, thoroughly washed with an acid solution of ammonium nitrate, and, finally, twice with water, to remove most of the ammonium nitrate. The precipitate is then dissolved in about 1 c. c. of 10 per cent. potassium hydrate, which is let fall drop by drop on the filter till the precipitate is dissolved ; the filter is now washed with about 25 or 30 c. c. of water, and the potassium hydrate solution, which now consists of 25-32 c. c. of solution, is boiled until the peculiar frothy appearance, which first appears on boiling, is entirely gone. The solution is then cooled until perfectly cold, and about 10 or 15 c. c. of strong hydrochloric acid added ; if the solution is kept cold this will form no precipitate, but a light yellow or colorless solution. The solution is now ready for the addition of stannous chloride, and the subsequent comparison of color produced with that obtained from the standard molybdie acid. The comparison is made in tubes that are calibrated like carbon-tubes, but which are larger, about 5/8-inch bore, and graduated to 100 c. c.; this makes them about 18 inches long. To make the comparison of color, first transfer the now acid solu

Jan 1, 1886

By N. Brown, J. Washburn, E. R. Parker

MOST previous quantitative work on creep of single crystals has been concerned primarily with developing empirical equations for the creep curve. Although the equations used by Cottrell and Aytekin¹ and Tyndall² represented the data quite well, it was often necessary to use different values of the constants for different specimens even though they were apparently tested under identical conditions. In the course of previous work on the effect of surface coatings on creep of zinc single crystals," it was found that equal resolved shear stress frequently did not produce equal creep rates in different specimens. The work of Chalmers&apos; in the very

Jan 1, 1954

By R. J. Shaffer

Hydraulic fracturing in rock masses involves complex and coupled processes of fractures propagating in discontinuous media and of fluid flow in discrete channels. The Unconventional Gas Program at LLNL is actively developing numerical models to gain insight in the physics of these coupled processes. This paper describes the current status of the FEFFLAP code, which models fluid-driven discrete fracture propagation in jointed media. We also discuss the results of a preliminary series of physical tests in which hydrofractures were driven across slanted interfaces between dissimilar materials, in blocks loaded in biaxial compression.

Jan 1, 1984

By R. J. Batterham, P. W. Roller

Granulated sinter mixes of three iron ore types were prepared with a range of water contents in a laboratory investigation. The mean diameter of the granulated mixes and the void fraction of beds of the mixes were determined experimentally. Pressure drop measurements over a range of flow rates were made in a laboratory permeameter with pressure tappings at several depths in the bed. The Ergun equation was applied to the results to determine the shape factor of the granulated mixes. Pressure readings down the bed were used to estimate the local void fraction in the bed using the Ergun equation and the calculated granule shape factors. It was found that there was a decrease in void fraction with depth in the bed. The significance of this and the variation of shape factor values with the amount of water used for granulation is examined in relation to the strength of granules of the sinter mixes. The experimental and mathematical techniques presented may be useful in interpreting the behavior of the permeability of sinter beds after ignition.

Jan 1, 1986

By B. J. Kochanowsky

To improve blasting methods it is necessary to know how the explosive force acts and how rock resists this force. Because of the tremendous power developed within milliseconds and the great number of other factors directly affecting the technical and economic results, an analysis of the fundamentals of blasting theory is difficult. But since the rules used for layout design and for calculations of size of explosive charges are based on theoretical assumptions, complete knowledge of blasting theory has great practical importance in mining. Analysis of Blasting Theory: It is interesting to note the opinion of blasting experts with respect to contemporary blasting theories. F. Stussi,&apos; Professor of the University of Zurich, stated: "We do not have enough experience yet to change our army engineering regulations in blasting and base it on new fundamentals. It is our duty to collect more practical data and to do more research in blasting to close this gap." K. H. Fraenkel,&apos; editor of the Manual on Rock Blasting published in 1953 in Sweden and written by well-known Swedish, German, Swiss, and French blasting and explosive experts, said: "To the best of our knowledge no suitable formulas for civil blasting work are to be found in the American, French or German literature."

Sep 1, 1955