Search Documents

Jan 1, 1944

By Robert C. Emmett, Donald A. Dahlstrom

FOR many years gravitational classification has been employed as a basic tool in beneficiation of minerals and coal. While improvements have been made to increase efficiency and fields of application, the basic flow pattern has remained relatively unchanged in most gravitational classifiers. Feed slurry is introduced into a settling pool wherein the coarser solids settle against either an upward or horizontal fluid current, or a combination of both, and are withdrawn in a concentrated underflow stream. The finer solids below the classification point possess too low a settling velocity and thus are primarily swept out through a weir overflow by the bulk of the fluid. Because of its simplicity, efficiency, and low power and maintenance costs, gravitational classification finds a wide acceptance for separations in the range of 20 to 325 mesh. Two factors resulting from the basic flow pattern employed in gravitational classification present difficult problems for certain installations. If classification at 60 to 200 mesh of separation is desired, capacity in terms of gallons of overflow per minute per square foot of settling pool area must be low to allow required solids to settle to the underflow. If a thousand or more gal per min of feed slurry must be handled, either a very large classifier or a number of smaller units must be employed, taking up floor space and head room. Examples of this are the large classifiers, wetting tanks, or settling tanks used in the coal industry for recovery of process water from fine solids. Units as large as 50 or 60 ft in diam and 60 ft high, requiring substantial amounts of steel, are not uncommon. A second factor is the lack of self-regulation in gravitational classification. As overflow rate increases, mesh of separation increases correspond-ingly. This normally heightens difficulties of bene-ficiation. If a fine mesh of separation is required at varying feed rates, the problem is more than doubled in complexity. One of the primary advantages of gravitational classification is low power requirement. Gravity feeds or very low pressure heads are employed. However, fluid energy is still present in the inlet stream and provision must be made to dissipate it properly to obtain uniform upward or horizontal currents. Rather than waste this energy, it would be desirable to utilize it to secure a greater degree of self-regulation and simultaneously increase classification capacity per square foot of area. A free vortex could be realized by a tangential entry of feed, resulting in generation of centrifugal force to complement force of gravity in its action. With greater force it should be possible to gain finer separation at any overflow rate per square foot of settling pool area as compared with conventional gravitational classification. Furthermore, as feed rate increases, centrifugal force will also increase and at least partially offset faster currents sweeping solid particles to the overflow. A more stable classification point should result. The liquid-solid cyclone is the most common application of a free vortex in the beneficiation field.' Many previous papers have emphasized uniformity of flow pattern within the cyclone which is largely responsible for the sharp classification that can be obtained.'-4 If a free vortex can be maintained in a non-pressurized vessel with a free surface it may be possible to realize a third advantage of sharper classification. This open-top cyclone would then achieve a minimum energy loss comparable to that with conventional classifiers, and a mesh of separation coarser than 150 mesh, extending the range of application of the free vortex. This is not presently possible with ordinary cyclones. To test the applicability of the free vortex to gravitational classification, a 30-in. diameter open-top cyclone was constructed at Northwestern University. The cylindrical section was 30 in. high and the conical section included an angle of 60". The feed nozzle was a standard 4-in. pipe entering tan-gentially, with centerline 17 1/2 in. below the top of the cyclone. The conical section was flanged near

Jan 1, 1954

Jan 1, 1952

By H. J. Denning, M. W. Brabbins, A. K. Isaac

The quality of a coalface floor is the essential element that enables powered supports to generate their designed loads in control of coalface strata. The paper introduces a technique for the appraisal of coalface foundation stability. A criterion of support efficiency, viz., the support pressure increase/strata convergence, is included in case study data obtained from investigations in the South Wales Coalfield, U.K.

Jan 1, 1984

By V. F. Marsters

SEEPAGES Of oil in Ecuador have been known for many years. The locality first to receive attention, and still worked in a modest way, lies on the north shore of the Santa Elena peninsula, between La Puntilla and Salinas. Operations were first conducted largely by local capital. Later, foreign companies acquired large blocks of land, where they have done considerable drilling. For details concerning present drilling activities in Ecuador, we are indebted to Leon Price, an American resident engineer of Ecuador. The information solicited, came to the author through the office of the American Consulate,' with permission to use it. The coastal plain bordering the Province of Tumbes, Peru, continues to the northeast, but narrows on passing the Zarumilla River. From this, point northward it widens toward Santa Rosa. In fact, the pampas, as shown on the official Wolf map, correspond fairly well to the areal extent of the coastal plain as far as Guayaquil. This is shown in a general way on the accompanying map. The author understands that the Guayaquil embayment is bordered on all sides by the coastal plain, as recognized at Tumbes and farther southwest, and that it can be followed without a break as far north as Palmar. This view is supported by the mapped area regarded by Mr. Price as favorable or possible oil territory. Moreover the islands in the Gulf of Guayaquil are the same geologically as the coastal edge, being composed of Tertiary sediments. The author understands also that Tertiary formations occur north of Palmar. According to a report by Mr. Cardon, of Guayaquil, Tertiary sediments are exposed in the region of San Francisco and extend to and beyond Pta. Calera. There is also reason to believe that at least the lower part of the valley of the Santiago River is occupied by Tertiary sediments, which probably border the coast line and extend into the River Mira basin, and into Colombia.

Jan 7, 1922

First actual production of titanium metal at the newly constructed Henderson, Nev., plant of Titanium Metals Corp. of America occurred in mid-October. Production will be expanded rapidly until the initial goal of 10-tons per day is reached. This will be equivalent to eight times the present world production of titanium metal. W. Eberstady & Co., New York City, has announced plans for construction of a $400 million plant for the manufacture of synthetic liquid fuels from coal in southern Illinois, if the Government will guarantee a minimum price for the gasoline and other products to be produced.

Jan 11, 1951

By A. M. Radigan, W. G. Prast

Various industrial minerals that are traded internationally receive support from governments, enabling these materials to be more competitive. The role of government in encouraging nonmetallics exports ranges from the ownership of an integrated mining company to partial or selective government ownership, to the sponsorship of exporter organizations. In certain cases, regional governments have a direct stake in the industrial minerals industry. This paper assesses the commercial impact of these involvements.

Jan 1, 1984

By M. M. Fine

In a laboratory study of grinding and classification of silica sand, a satisfactory means of producing the medium-fine specification sand desired by producers of flint-glass containers was developed. The best procedure consisted of ball-mill grinding and double classification, which gave a properly sized sand containing less iron than the feed.

Jan 3, 1950

On October 20, 1964, in his Waldorf Towers suite, death came to Herbert Clark Hoover, 31st President of the United States. At his bedside were his two sons, Allan A. and Herbert Hoover, Jr. Many years of humanitarian and public service earned him the gratitude of millions here and abroad. The Nation mourned his death. For the mining fraternity and AIME in particular, the life of Herbert Hoover held particular meaning. During the years from 1895 to 1914 when he was actively engaged in mining, he conducted himself with extraordinary competence, energy and integrity. In the years following, when his qualities of administration and leadership literally forced him into the limelight, he continued his interest and lent his talents for the benefit of the engineering profession.

Jan 11, 1964

By J. P. Hammond, C. J. McHargue, J. R. Holland

IT has been reported that both berylliumL and zirconium&apos; developed the same basic textures during rolling at temperatures up to 1475 °F as at room temperature, differing only by an increase in the spread of basal planes toward the transverse direction as the temperature of deformation was increased. Iodide titanium&apos;&apos; rolled at 1050°F has a texture similar to the cold-rolled texture, {000l}, 25° to 30" from the rolling plane toward the transverse direction, <1010>, Rolling iodide titanium at 1450°F produced a more random condition with the basal planes parallel to the rolling plane and no direction strongly aligned with the rolling direction.

Jan 1, 1957

By Allan M. Hale

The paper discusses past trends in phosphate reclamation, indicating advantages and disadvantages of land and lakes, sand tailings capped with overburden, phosphate slimes capped with overburden, and overburden fill reclamation. In addition, new techniques of reclamation such a clay settling-pond disposal and wetland restoration are discussed.

Jan 1, 1983

By M. Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molybdenum, lead, zinc, and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high, the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper prices; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1984

By G. A. Perry, C. D. Iles

The philosophy used in designing and writing Duval&apos;s Sierrita mine design programs is discussed. The Sierrita Incremental Design system (SID) is reviewed with emphasis on Pushback Extraction Design (PED). PED is a method by which predesigned pushbacks are sequenced into an optimized period-by- period design. The design that PED Produces is the design used in the field without further modifications. The advantage of SID is that it provides a practical, mineable open pit design. PED is not a theoretical design system. It is in operational use.

Jan 1, 1984

By J. A. Benell

DIOXIDE of silicon, commonly called silica, is one of the greatest single constituents of modern in-dustry. It is brought most clearly to the mind when we consider the various kinds of sand and their rela-tion to industry. The major portion of.all sand is silica, and should be its principal component part in building materials. As an abrasive for cutting, polish-ing and sand-blasting, sand serves a vital purpose in many industries. Even lumber is now being sand-blasted, to cut away the softer grains of wood, leaving the harder grains in relief. The result not only in-creases the beauty of the wood, but adds to it an ap-pearance of antiquity. The common uses of silica in industry may be classified about as follows: Chemical industries-filtering medium; manufacture of carborundum; manufacture of water-glass. Paint-inert extender. Mineral fillers-wood filler; filler in rubber, hard rubber, pressed and molded goods, phonograph records.

Jan 5, 1928

By S. O. Reichert

The nuclear industry has made a considerable effort to reduce environmental pollution with the result that knowledge in the field of radioactive waste management is well advanced. An example of the methods used for radioactive waste disposal is provided by the Savannah River Plant (SRP) operated by E. I. du Pont de Nemours & Co. for the AEC. It occupies an area of 320 sq mi along the Savannah River downstream from Augusta Ga., and has production facilities that include a fuel preparation area, three reactor areas, two chemical separation areas (F and H), and a heavy water plant. Gaseous, Liquid and Solid Radioactive Wastes Are Handled During Disposal The primary sources of radioactive waste are the reactor and chemical separation facilities. The reactors are cooled and moderated by heavy water which, in turn, is cooled by river water in heat exchangers. This arrangement prevents irradiation of the river water so that radioactivity is not discharged into the river water except when small quantities of moderator are lost by heat exchanger leaks. Because of the high cost of heavy water, these losses must be kept to a minimum.

Jan 9, 1968

By W. A. Lang, K. C. Gilbart, E. Stansfield

It has long been known that coal is unstable and oxidizes in air, even at ordinary atmospheric temperatures; also, that such oxidation affects the analysis of coal. Nevertheless little or no precaution is taken to prevent oxidation in the ordinary methods of analysis, and the possibility of error due to oxidation is sometimes ignored even in researches on coal. Although the general nature of coal oxidation is well known, and many workers have made careful studies of the rate of oxidation of different types of coal exposed to oxygen at different temperatures, yet the amount of oxidation coals undergo in the ordinary process of analysis, and its influence on the determined analysis, is not well known, and the published data are widely scattered through the literature. This paper is a collection, from this laboratory, of data that bear on the subject, together with a brief summary of three methods employed here to evaluate the oxidizabil-ity of coal. The post-Carboniferous coals of Alberta range all the way from anthracite down to lignite. As some of them are notably susceptible to oxidation, the necessity for care was early forced upon our attention, and oxidation has been reduced either by the removal of air with a vacuum pump or by the displacement of air with natural gas (methane). The two routine analytical operations most liable to involve oxidation are the preliminary, partial drying of the crushed coal (called air-drying) and the determination of moisture. The first is a prolonged operation on coarse coal at ordinary temperatures, and the second a short treatment on powdered coal at higher temperatures. Oxidation also occurs in coal samples stored in ordinary sample bottles. In order to gain information for this study, determinations were recently carried out on the same samples in air, in natural gas, and in vacuo. Sixteen coals were tested; three would be classed in the United States as coking bituminous coals, two as noncoking, nonslacking, bituminous coals, and the rest as subbituminous. Table 1 gives typical analyses of these coals as mined.

Jan 1, 1934

By A. L. Senkayi, L. R. Hossner, J. B. Dixon, J. S. Ahlrichs

Chemical and physical properties of soils and overburden materials must be evaluated prior to strip mining activities. This information can be used to assess whether subsurface overburden can be equal in quality to the native soils, especially when these soils are classed as prime farm lands. In northeast Texas, lignite primarily occurs in the Calvert Bluff formation which is underlain by the Simboro and Hooper formations. These formations are in the Wilcox group (early Eocene). The Carrizo formation, that unconformably overlies the Calvert Bluff formation, consists of thick layers of sand with poor water and nutrient retention capabilities. These materials are least suited for placement on the surface of reclaimed land. The oxidized, medium textured overburden of the Culvert Bluff and Simboro formations possess adequate water and nutrient retention properties and are better suited for sustained plant growth when compared to the existing native soils. Non-oxidized Calvert Bluff and Hooper sediments generally have acceptable properties for reclamation although acid forming sulfides occasionally occur. Materials high in sulfides must be buried during mining or appropriately treated prior to reclamation.

Jan 1, 1984

By Thomas Fraser

"AIR-SAND" is the term which has been given to a process of separating refuse material from coal by means of a body of dry sand artificially fluidized and maintained in that condition by a continuous stream of air bubbles flowing through the sand body. By proper regulation of the rate of air flow, this fluid air-sand body may be maintained at such a density that coal will float near the surface and the refuse, which is heavier, will sink through the sand to the bottom of the container. This separation is a float-and-sink operation similar to the separation of wood chips and stones in water; the one floats and the other sinks, irrespective of size of pieces. This was the objective sought in the development of this method of cleaning coal-a dry process which requires no preliminary sizing of the coal. METHOD OF PRODUCING THE AIR-SAND MEDIUM Figure 1 shows the cast-iron cell used for testing at the Central District Experiment Station of the Bureau of Mines, Urbana, Ill. This consisted of two castings: a. rectangular box 12 in. square in cross section and 18 in. tall, open at both ends and flanged on the bottom; and a cubical box also 12 in. square inside, with a closed bottom and flanged top. A porous diaphragm is bolted between the flanged ends of the two castings. The upper part of the cell above the diaphragm is filled with river sand screened through 20 mesh without removing the dust. Air under suitable pressure is admitted to the lower part of the cell below the diaphragm. The air passes through the diaphragm and bubbles up through the sand, distending the mass and throwing the sand particles into motion.

Jan 2, 1926

By Francis S. Kendorski

INTRODUCTION Nuclear waste has been generated since the time of the Curie&apos;s and continues to be generated worldwide at an ever-increasing rate as the world will (and should) rely more and more upon fission (and hopefully fusion) for power. Also, the needs for strategic weapons will also generate so-called defense wastes. The largest class of high level nuclear waste (HLW) is spent fuel, the tail end of the nuclear reactor fuel cycle. At present, spent fuel is stored at the reactors producing it or at a few accepting places for away-from-reactor storage. All such storage facilities, as presently constructed, will begin to run out of usable storage space during the next decade or so. Congress enacted and President Reagan signed into law in early 1983 the National Nuclear Waste Policy Act of 1982. This law provides for the permanent isolation of nuclear waste in deep geologic repositories. The Act sets 1998 as the date at which the first repository should be operational. This date is extremely ambitious, and the Department of Energy (DOE), which is charged with the responsibility of constructing and operating repositories, admits that this date will slip by at least a few years. The Act also provides for licensing of repositories by the Nuclear Regulatory Commission (NRC) in a fashion very similar to nuclear power generating reactors. This requirement imposes a very special rigor on the analyses, investigations, designs, construction, and operation of repositories so as to assure the protection of the public and the environment from radioactive contamination. In addition the states and affected Indian Tribes must be consulted, especially concerning siting, and, needless to say, no one wants a HLW repository in their back yard.

Jan 1, 1984

Jan 1, 1939