Search Documents

By A. A. Dor

Out of nine new major iron ore concentrators put in operation during the last three years, or expected to be commissioned in 1968, seven incorporate primary grinding mills and have a total design capacity of 13,150,000 ltpy of pellets, while only two include conventional rod and ball mill grinding circuits for a total design capacity of about 6,100,000 ltpy (Table I). This evolution in the application of primary grinding to hard, fine grained magnetite ores represents an important development in the technology of mineral processing. It has been the outcome of comprehensive testwork in the laboratory and in pilot plants.

Jan 11, 1968

By John D. Kalasky

The success in providing adequate ventilation to the active faces of a coal mine for all methods of mining depends upon good face control and the air distribution and control system. A good system provides overcasts, air locks, regulators and bleeders so that an adequate flow of air will be confined to the working places with least opportunity for interruption, and that a flow of air is maintained, however small, across the worked out area to the bleeder and away from men and equipment at all times. In gaseous mines, it is just as important to satisfy effective bleeding as it is to satisfy the air volume requirements in the operating splits. The two requirements go hand in hand. Although not complicated, ventilation and methane drainage in longwall mining in a gaseous mine require careful forethought and adequate facilities to make them safe.

Jan 8, 1966

By Stephen Krickovic

As it is commonly understood in the bituminous coal mining industry, pillaring means removal, as completely as is practical, of all pillars formed in the development of headings and rooms on first mining. The degree to which this can be accomplished, termed percent of recovery, is of course dependent generally upon the physical conditions of the bottom and the overburden, the system of min-

Jan 2, 1955

By Michael D. Loy

While the coal industry in general has been slow in accepting automation, the last few years have seen a myriad of products developed by the private sector. These packages run the full gamut from sophisticated geological information systems to line entry discounted cash flow analyses. This paper is an attempt to unravel the confusion that may exist about mining software. Discussions will highlight major differences between software products (such as block vs. grid models, prefeasibility programs vs. Monte Carlo analyses), briefly discuss known vendors, list known package features and touch on hardware requirements. The paper also focuses on the costs of automation (both software and hardware), possible trade-offs, advantages to in-house systems (vs. timesharing), a recommended review/selection process (including suggested RFP format), a test case procedure, when to bring in a consultant, and staffing considerations.

Jan 1, 1983

Jan 1, 1924

The volumes of Transactions, which are published annually, contain the list of officers, rules, etc., the Proceedings, and the papers revised for final publication. (In this revision, after the preliminary publication, authors are permitted to use the largest liberty; and the changes and additions made in papers are sometimes important. It should be borne in mind by those who study or quote a paper in the preliminary edition, that they may not have in that form the ultimate and deliberate expression of the author's views. It should be added, however, that in the majority of cases there are no important changes.) These volumes are for sale as follows, in paper covers:

Jan 1, 1917

By G. C. Wallick, W. R. Foster, J. G. Savins

Inasmuch as the differentiation and integration methods represent different modes of rheological analyses, a dual scheme of analysis using both methods should lead to a generalized method of data analysis. A dual differentiation-integmtion method of analysis is applied here to the Poiseuille flow of a variety of ideal Generalized Newtonian and viscoplastic models. Using machine-processing techniques, the result is a spectrum of response patterns which are expressed in terms of certain derivative functions. It is shown that these characteristic functions form the basis of a highly-sensitive analytic technique for optimizing the selection of the most appropriate functional relationship between shear rate and shearing stress. INTRODUCTION In the first paper of this series, Savins, Wallick and Foster1 presented an historical review of the salient features of the differentiation method of rheological analysis in Poiseuille flow, and also indicated how the method could be applied to problems involving plane Poiseuille flow. It was shown that the differentiation and integration methods, although basically not incompatible, do represent different modes of rheological analysis. This suggests that valuable background information regarding the probable response characteristics of real data obtained with the differentiation method can be obtained from an integration method-differentiation method analysis of the response of a variety of ideal rheological models. The present paper describes how this dual method of analysis has been applied to suites of idealized models representing a wide variety of Generalized Newtonian and viscoplastic behavior which have received attention at various places in the literature.

W. VAN DER GRACHT, Tulsa, Okla. (written discussion.*).-I fully agree with Mr. Daly's observation that there is such a coincidence between petroleum deposits and geosynclines as to suggest them to be "closely allied phenomena." However, I accept no "identity of cause." To me the explanation is a simple one. Geosynclinal deposition is the first phase in the formation of a mountain, chain, and petroliferous deposits are indeed closely allied to zones of, mountain folding. In fact, petroleum is a typical occurrence in those beds, which represent the flysch facies, to use the Swiss expression. The uplifting of a great mountain chain is a very slow process; it gradually sets ill as a slow geo-anticlinal upheaval within a zone off former geo-

Jan 1, 1918

By S. H. Ash

Safety records in the mineral industry for 1954 will do well to hold their own as compared with 1953, because of the poorer rate in the coalmining branches, even without the recent mine explosion at the No. 9 mine of the Jamison Coal & Coke Co., Farmington, W. Va., that killed 16 persons. .The cause of that disaster has not yet been ascertained. The metal-mining branch appears to have improved its record over the last year, however. Health Diesel equipment continues to be favored in non-coal mines. Equipment includes locomotives, trucks, tractors, and muckers. Of major concern and interest is the establishment of a new threshold limit for oxides of nitrogen-5 ppm as compared with 25 ppm. This gas is the most harmful component of diesel-engine exhaust gas

Jan 3, 1955

By Howard R. Hughes

In drilling for water and oil to reasonable depths through the generally soft yielding clay and sand formation of the Coastal Plain of Texas, Louisiana, and Mississippi, the rotating method of drilling was adopted, principally on account of the easy and quick penetration, and the low cost of the drilling plant. In favorable ground, free of heavy gravel and rock strata, as much as 1,600 ft. has been drilled in less than 36 hr., although such performances were of course rare. Hydraulic rotary drilling, or, as it is now called, rotary drilling, was used in the above States as early as 1880. The plant consisted of an ordinary derrick, a 25-h.p. boiler, a small hoist, a steam pump, and a water swivel with hose attachment, and an ordinary flat diamond-pointed bit. The successful drilling in of a phenomenal oil well by this process on Spindletop, near Beaumont, Texas, on Jan. 10, 1901, and the ascertained impracticability of drilling subsequent wells in the same locality by other methods (owing principally to heavy quicksand under pressure from below), brought rotary drilling into great prominence, practically to the exclusion of any other process throughout the Coastal Plain, and later on elsewhere. The method, as its name implies, involves the rotation of a pipe by means of machinery placed on the derrick floor. A drill bit attached to the lower end cuts a clearance for the drill pipe, with much the same motion and effect as an auger. Water forced through the drill pipe by means of a pump, and escaping through the bit, removes the cuttings and returns to the surface outside the drill pipe. In this manner the hole is kept open, permitting the drill stem to rotate freely. The pressure of the column of muddy water holds up the walls of the hole until it has been cased. Practically all the wells of the Gulf coast region, numbering nearly 10,000, have been drilled with this system. During the last five years its use has been extended to many other States and countries.

Jan 1, 1915

By Walter B. Devereux

Metallic copper is a product of native metallurgy in various parts of Mexico, and by somewhat varied processes. While recently examining copper mines in the State of Jalisko, I had an opportunity of witnessing Mexican copper smelting by a process which I have not seen described, and which is interesting from the fact, that a fine quality of copper is produced from sulphurous ores in three metallurgical operations, and apparently without excessive loss. The process was carried on in buildings which were part of a plant erected by an American more than twenty-five years ago for the purpose of smelting and working copper. After a few years this man met with accidental death, and the works have been but little used since. Located in the centre of a high range of mountains, far from any town or seaport, and inaccessible except over difficult mule trails, these substantial buildings, filled with furnaces and heavy machinery,

Jan 1, 1883

The suggestions of the members of the Institute are very much desired by-the Committee on Nominations prior to deciding upon its nominations to fill the places of those officers who retire early in 1917. The Committee must make its final report to the Board of Directors early ill October. The members are, therefore, -asked to send in promptly their suggestions for Directors as well as for Vice-Presidents and President. The Committee hopes to hear from a large number of the members. The officers to be elected at the annual meeting in February, 1917, are: One officer, known as Director and president. Two officers, known as Director and Vice-President. Five officers, known as Director. The attention of members is called to Articles V and VII of the Constitution, and to By-Law XIII, which reads as follows: "The geographical districts to be considered by the Committee on Nominations shall be as follows, until otherwise ordered by the Board. District No. 1. New England, New York, and New Jersey, excepting New York

Jan 9, 1916

By R. V. Horrigan

High purity ZrC14 (25 to 200 ppm of metallic impurities) can be readily prepared in simple apparatus by thermal decomposition of alkali chlorozirconate fused salts at 500° to 600°C and at atmospheric pressure. Suggested phase diagrams for the systems NaCI-ZrC14 and KCI-ZrCI, are presented. ALKALI chlorozirconate compositions — anhydrous fused mixtures of ZrCl4, NaC1, and KC1— are manufactured commercially and are used by the magnesium industry to introduce zirconium into magnesium alloys. Zirconium refines the grain size and improves the physical properties of many important magnesium alloys. In the course of working with chlorozirconate compositions of high ZrCl4 content, it was noticed that these salts decomposed progressively itwaswith increasing temperature to yield considerable amounts of a ZrCl4 sublimate of high purity together with a solid chlorozirconate residue. Further research led to: 1—improvements in the

Jan 1, 1956

By U. Runolinna, R. T. Hukki

Preliminary separation of precious metals by flotation can offer a simplification of the conventional method of treatment of anode slimes. Laboratory flotation experiments show that rich gold and silver concentrate can be obtained with excellent recoveries.

Jan 11, 1950

Jan 1, 1934

FIRE tubes are commonly made in order to frighten horses or to harm enemy soldiers, but although fire issues from them, they do not cause much damage because they cannot be used at a distance. If you wish to use them, you are not able to approach close to the enemy, for if there is anyone who is afraid, he does not let you approach nor does he come near you until he sees that they have finished burning. Thus, in short, the assault with this is one that is seen beforehand, and for which there is always time to decide on some action in defense. It is indeed true that they are beautiful things to see and when the name tubes of fire is heard it terrifies those who do not have a defense ready. When four, six, or indeed ten or twelve of these are put in the hands of as many courageous and united men, they are surely good in forcing passage on a guarded bridge, or in entering or holding a gate, road, or other narrow place. They serve also for setting fire to dwellings or the enemy's supplies,

Jan 1, 1942

By Harmon E. Keyes

Harmon E. Keyes (Chemical & Metallurgical Engineer, Eagar, Ariz.)-Chemical dissolution of chalcocite by acidic ferric sulfate is well known. Resulting elemental sulfur may be oxidized to sulfuric acid by heated ferric sulfate. Laboratory tests at Southwest Experiment Station, USBM, Tucson, generally confirmed stoichiometric relations of 1 part Cu dissolved to 1.750 parts ferric iron reduced, using CP chemicals, dried ore samples, and apparatus cleaned with potable water. Recirculation with open-drainage percolation to increase copper in leaching solvent was followed successfully when appropriate, both in laboratory and Pinto Valley pilot tests. Before 1924 attempts to produce ferric sulfate by aerating ferrous sulfate solution were known. Initial oxidation was satisfactory, but rate slowed below practicality as oxidation progressed and acidity increased. Also, due to hydrolysis of ferric sulfate, a ferric precipitate of hydroxide and basic sulfate resulted. Both laboratory and pilot plant tests gave similar results, regardless of whether CP ferrous sulfate or scrap iron cementation discard solution was used. Rapid oxidation of ferrous hydroxide by air alone is well known to analytical chemists. I demonstrated a process to produce acidic ferric sulfate solutions by precipitating ferrous hydroxide with milk of lime, aerat-

Jan 1, 1973

By David C. Yang

INTRODUCTION Over the world, and especially in the United States, there is increasing dependence upon progressively lower grade ore deposits. These lower grade ores are frequently difficult or impossible to process due to complex mineral assemblages being very finely disseminated. Thus, many of the conventional mineral concentration methods are not applicable to these ores. For the last few decades, research in the more exotic mineral processing techniques has been conducted, both in universities and in governmental and industrial laboratories. Since its inception, the Institute of Mineral Research of Michigan Technological University (MTU) has devoted much of its attention to the problems of processing refractory, low grade ores. Recently a new flotation system was developed which shows promise of being applicable to a broad range of ore types. This process has been the subject of two allowed patent applications. This paper describes the details of such a flotation system which is potentially useful for treating ultrafine minerals. Some highlights of the testing program on a variety of iron ores and a group of lithium-bearing ores will be presented. EXPERIMENTAL PROCEDURES Both iron and lithium ore flotation treatments followed the same general procedures, with minor differences in pH and in reagent dosages. The method is rather simple, efficient and economical from the standpoint of recovery and the cost of reagents consumed.

Jan 1, 1979

By Yoshihiko Shimazaki, Hokuichiro Ohmachi

Mineral resources of Japan are remarkably characterized by the diverse variety of ores. Seventeen kinds of metallic ores are produced in Japan from approximately 175 mines, but the country is becoming increasingly dependent on imported ores, and 23 ores such as bauxite, nickel and platinum are not produced domestically. Self-sufficiency of non-metallic minerals is higher than metallic ores. Twenty three non-metallic minerals such as fire clay, pyrophyllite dolomite, and limestone are produced from about 1264 mines. About 22 minerals such as graphite, asbestos, fluorite, and phosphorites are not produced in the country. One of the major concerns of Japan is raise the self-sufficiency of raw materials. The result of the analysis of the mineral potential of Japan in relation to possible future domestic supply and is reported.

Jan 1, 1976

By Irving Fatt, Robert J. S. Brown

INTRODUCTION The wettability of reservoir rocks is recognized as one of the major factors that determines their multiphase flow properties. Multiphase flow properties in turn govern reservoir performance. For this reason, the reservoir engineer is vitally interested in the wettability of reservoir rock. The production research scientist is interested in wettability because the solution of the problem of improving waterflood recovery by use of surface-active additives may hinge on a detailed understanding of the wettability of reservoir rock. Early workers believed that all reservoir rocks were preferentially water wet. Continued study soon uncovered certain rocks which had flow properties that indicated that they were preferentially oil wet. Recent studies show that there is a spectrum of wettability. Some reservoir rocks have multiphase flow properties which indicate that they have an intermediate wettability. The differences in recovery observed among different reservoirs may, in part be the result of small differences in wettability. Differences in wettability amcng reservoir rocks may be the result of differences in the fraction of the total surface area that is preferentially oil wet and preferentially water wet. Nuclear magnetic relaxation measurements may provide a method for determining the fraction of preferentially oil wet and preferentially water wet area in porous media. Measurements to be reported here were made on water-saturated unconsolidated sand packs which were mixtures of preferentially oil wet and preferentially water wet sands. The resulting data show definitely that the fraction of each wettability in these sand packs can be determined by this nondestructive method of measurement. THEORY OF NUCLEAR MAGNETIC RELAXATION The details of the theory of nuclear magnetic relaxation have been presented previously1. In this paper, only a very brief review of the theory will be given to show its application to the measurement of fractional wettability. Nuclear magnetic relaxation is a process of adjustment undergone by certain atomic nuclei when their magnetic environment is changed. They adjust, or relax, to be in equilibrium with a new magnetic field. The reason that some atomic nuclei are affected by a magnetic field is that they themselves behave in some respects like tiny magnets. In particular the proton, the nucleus of the hydrogen atom, behaves as a magnet. The proton spins, somewhat as the earth spins on its axis. The spinning charge produces a magnetic field just as current traveling in a loop of wire produces a magnetic field. No net charge is required, however; for instance, the neutron has spin and magnetic moment. When the spinning proton is subjected to an externally applied magnetic field, its axis tends to line up with the magnetic field, somewhat as a compass needle tends to line up, but the spinning proton cannot do this as easily as the needle can. The proton also has mass, and its spinning mass makes the proton behave somewhat like a gyroscope. As is well known, a force which tends to change the axial direction of a gyroscope merely causes the gyroscope to precess: lhat is, the axis begins to trace out a conical surface. The gyroscope cannot actually assume the position suggested

Jan 1, 1957