Search Documents

By Perry Olcott

The Texas Gulf Coast had a rather disappointing year in the type of oil fields found. Although 17 fields were found in the area during the year, as against 21 fields in 1938, no field of major proportion was discovered. Of these 17 fields, 11 were oil fields, 4 were gas and distillate fields, and 2 were gas fields. The wildcat activity for the year resulted in about 400 dry holes, although probably 10 per cent of these were edge wells close to proved areas. During the year, 1455 oil and gas wells were completed as compared to 1637 wells in 1938, a decrease of 11 per cent. Production for the Texas Gulf Coast area for the year was 100,253,937 bbl. as against 92,530,467 bbl. produced in 1938, an increase of 8 per cent. The daily average production was 274,668 bbl. for the 365 days in the year, although only 252 producing days were allowed by the Railroad Commission; that is, 69 per cent of the time as compared to 71 days shut in for 80 per cent of the time producing in 1938. The total number of oil and distillate wells producing at the end of 1939 was 9495 as against 8451 at the end of 1938—an increase of 1044 wells, or 12 per cent. Of these wells, 6547 were flowing and 2948 pumping, or 69 per cent flowing. At the end of the previous year, 66 per cent of the wells were flowing. New Fields Angleton, Brazoria County.—The Angleton field was discovered by the completion of Glen McCarthy's No. 1 Carr in October for an initial production of 180 bbl. a day of 50" gravity oil through 11/64-in. choke with 3400 Ib. on tubing. The field is 1½ miles east of the town of Anchor. The discovery undoubtedly can be credited to the reflection seismograph, since several companies worked the area from 1933 onward with this type of exploration. The principal block was taken by the Humble company in 1934. Two deep holes by Humble revealed the presence of structure, although both were dry. The Humble and Sun companies later contributed money and acreage toward the drilling of the discovery well. The production is from a sand in the Frio, about 1700 ft.

Jan 1, 1940

By C. P. Sandberg

C. P. Sandberg, London, Eng. 1 think we should all be grateful to the Pennsylvania Railroad Company, and to their chemist, Dr. Dudley, for spending so much time and money in order to solve an important question; nor are me less indebted to the public spirit which leads them to impart tlie experience thus gained. In Europe nothing similar has hitherto been done, either by a company or by any private individual. In England the great railway companies employ their engineers in other ways, and do not keep a chemist or specialist to study rails; bat even if they did they would probably not publish the results. The chief professional engineers are so occupied with their private practice of railroad construction generally, that they cannot be expected to devote their time and energies to so special a question. The German Railway Union has, in my opinion, missed the real object of its elaborate researches by falling into the error of specifying costly, impracticable tests for rails—tests at the same time which do not infallibly expose the impurities that may be in the rails under examination. There has, therefore, been nothing done on this side of the Atlantic in the way of exhaustive study to determine the best composition for steel rails. America should consequently have full credit for the enlightened example which she has set. I wish, however, to make a few remarks on Dr. Dudley's second paper,—& paper which follows very much upan the same lines of argument as the first red three years ago, upon which I have previously touched in my pabr on the same subject read at the meeting in August last. If Dr. Dudley had discovered a new metal he could hardly, I think, have taken wore pains to prove that he was correct in his first formula for the best chemical colnposition of steel rails. But I hare seen so much done in the way of proof by experiment that I am inclined to think that almost anything can be proved by experiments and by satnples. If Dr. Dudley would only give up his formula, which would not suit any country—not even America—

Jan 1, 1881

THE transformation, in a sample of levitation melted iodide titanium, has been studied with a Leitz hot-stage microscope. The specimen was etched in HF:HNO3: glycerine, (1:1:2) giving a structure shown in Fig. 1, and was then heated at approximately 5OC per min. At 870°C (±5OC) the etching product disappeared, the a-grain boundaries showed in relief, and some new grain boundaries (presumably of ß) appeared (Fig. 2, see arrow). Some evidence of ß-grain growth is indicated by the apparent longitudinal movement of a ß-grain boundary shown in Figs. 2 and 3 (see arrows). The specimen was later heated to 1000°C and then cooled at 2°C per min. At 845°C rumpling of the surface was first noticed, Fig. 4, and continued at constant temperature. The photomicrograph reproduced in Fig. 5 was taken 6 sec after Fig. 4, at 845°C. Fig. 6 shows the structure after cooling to room temperature. The room-temperature structure, showing a rumpled surface has been observed by previous investigators.' These structures presumably indicate a sheer transformation ß - a, athermally nucleated, but capable of isothermal progression.

Jan 1, 1960

By P. S. Bagga, P. T. Luckie

Liberation (the process of destroying the interlock between unwanted materials, such as mineral matter and pyrite, and coal) is one of the most important precursors to the benefication of raw coal in order to produce high grade marketable coals at economical recovery levels. Liberation is achieved usually by comminuting the raw coal. However, because of the significant interaction between the production of fine particles to achieve liberation and the cost of separating fine particles, the coal industry needs a method projecting the change in washability with size reduction. Such a projection can be combined with size reduction and separation simulators in order to examine completely beneficiation circuitry to produce coals of stringent specification. This paper presents the development of an appropriate liberation model for coal and its solution by Monte Carlo simulation to predict the expected washability of the raw coal as a function of comminution. It includes model validation with a known binary mixture as well as with a known teritary mixture.

Jan 1, 1983

By Walter S. Tower

IN making comparisons of steel industries, one country with another, the convenient common denominator is annual capacity to make raw steel in the form of ingots. It is always necessary, however, to remember that there are different methods of figuring such capacity. For most countries no official figures on capacity are available, and the only authentic data on production are now six or eight years old. But in spite of those limitations on the accuracy of statistical comparisons, any flaws in the figures are probably not serious enough to alter materially the larger conclusions which may be drawn from them.

Jan 1, 1944

Jan 1, 1968

By AIME AIME

ON Thursday, Oct. 9, oil men from far and wide gathered at Beaumont, Texas to participate in a three-day celebration of the fortieth anniversary of the completion of the famous Lucas gusher well at Spindletop field just south of Beaumont, and to pay tribute to Anthony F. Lucas, for whom the Lucas Medal of the A.I.M.E. is named. In the afternoon the gathered host drove to the site of the discovery well to dedicate a 58-ft. granite monu¬ment erected on the spot where the original derrick stood. Representatives of the A.I.M.E. took a prominent part in the dedication ceremonies, giving the two principal addresses of the afternoon's program. Everette DeGolyer, past President, paid a personal tribute to Capt. Lucas, as a pioneer producer, an engineer, and a friend and well wisher of all young engineers. He gave a splendid picture of the useful and full life of Capt. Lucas who always took a great interest in the activities of the Petroleum Division of the Institute, from its inception to the time of his death.

Jan 1, 1941

By H. C. Chang, N. J. Grant

Creep of very coarse grained, high purity aluminum was studied at 400° to 1100°F with an initial stress range of 50 to 1200 psi. The process of boundary sliding and migration was studied. The driving force of boundary migration under creep conditions is shown to be a combination of strain energy migrationand surface energy. A theory is presented regarding the strainenergyrole the grain boundaries play under creep conditions. From this thetheory intercrystalline failure of commercial alloys can be explained. Also from this theory an optimum grain size should exist for good high temperature properties of high purity materials. IN the investigation of the creep of very coarse grained, high purity aluminum previously reported,' the cyclic nature of the process of grain boundary sliding and migration has been established by microscopic observation of the actual creep process as well as metallographically. It was also substantiated by measuring localized strains across the grain boundaries. In addition, it was shown how extensive subgrain and fold formation may result from boundary sliding and how the slid grain boundary may become sharply wavy as a result of subgrain formation. Since the publication of those results, additional information on the process of grain boundary sliding and migration has been obtained. It is the purpose of this paper to report on the direction and driving force of boundary sliding and migration, the effect of grain size, and the effect of temperature. Finally the effect of decreasing purity (alloys 2s and 3s) on the process of boundary sliding and migration is noted. From these results, an explanation is presented for the intercrystalline failure of alloys under creep conditions. The effects of grain size on the creep properties of impure and high purity materials are discussed in the same light. The experimental procedures and technique have been presented elsewhere.' It is only necessary to state how the 2s and 3s aluminum specimens are prepared. Machined specimens were first annealed at 600°F for about 12 hr. In order to produce a large grain size the specimens were then stretched 3 to 8 pct. The specimens were marked with reference marks, electropolished, annealed at 900°F for 24 hr and at 1150°F for 12 hr, and repolished. The grain size of 2s aluminum produced by this treatment is comparable to that of high purity aluminum in the direction of its width of the specimen, i.e., there are 2 to 4 grains across the width of the specimen. However, the grains of 2s aluminum are 3 to 10 times longer in the direction of the specimen axis. On the other hand, the grain size of coarse grained 3s aluminum ranges from 10 to 20 grains across the width of the specimen due to the treatment just outlined and therefore is much smaller than that of both high purity and 2s aluminum. As in 2s aluminum, the grains are about 3 to 10 times longer in the direction of the specimen axis than in the direction of the width of the specimen. The arrangements of the grains in 2s and 3s aluminum were generally irregular; therefore it was difficult to follow the course of the grain boundaries. Results Method of Presentation: In order to show the arrangement of the grains, especially the direction and positions of the grain boundaries, traces of the grain boundaries on the four surfaces of the specimens were unfolded and mapped out after macroetching. Figs. 1 and 2 show the structural development drawings of specimens P-3 and P-8 respectively. The two flat surfaces (of which the front one faces the microscope) and the round-edged surfaces will be called the "front surface" and "back surface" and

Jan 1, 1954

C. P. Sandberg, London, Eng. 1 think we should all be grateful to the Pennsylvania Railroad Company, and to their chemist, Dr. Dudley, for spending so much time and money in order to solve an important question; nor are me less indebted to the public spirit which leads them to impart tlie experience thus gained. In Europe nothing similar has hitherto been done, either by a company or by any private individual. In England the great railway companies employ their engineers in other ways, and do not keep a chemist or specialist to study rails; bat even if they did they would probably not publish the results. The chief professional engineers are so occupied with their private practice of railroad construction generally, that they cannot be expected to devote their time and energies to so special a question. The German Railway Union has, in my opinion, missed the real object of its elaborate researches by falling into the error of specifying costly, impracticable tests for rails—tests at the same time which do not infallibly expose the impurities that may be in the rails under examination. There has, therefore, been nothing done on this side of the Atlantic in the way of exhaustive study to determine the best composition for steel rails. America should consequently have full credit for the enlightened example which she has set. I wish, however, to make a few remarks on Dr. Dudley's second paper,—& paper which follows very much upan the same lines of argument as the first red three years ago, upon which I have previously touched in my pabr on the same subject read at the meeting in August last. If Dr. Dudley had discovered a new metal he could hardly, I think, have taken wore pains to prove that he was correct in his first formula for the best chemical colnposition of steel rails. But I hare seen so much done in the way of proof by experiment that I am inclined to think that almost anything can be proved by experiments and by satnples. If Dr. Dudley would only give up his formula, which would not suit any country—not even America—

Jan 1, 1881

By Thos. W. Gibson

The object of taxation is the raising of a revenue. Unless a tax accomplishes this, it is a failure. The right to take for public purposes a part of the moneys obtained from the carrying on of private enterprises is an attribute possessed only by a lawful government, and may indeed be called the supreme attribute of government. In free, democratic communities this power must of necessity rest upon the consent of the governed. Power implies obligation, hence it is obviously the duty of a government, in framing a system of taxation, to provide one which, while effective in producing a revenue, is also just and impartial. • It will be conceded that mines and mining property ought to bear a fair share of the public expenditure. The question is, upon what basis taxation should proceed. Two separate taxing principles are usually contended for: Taxation should be proportionate to the benefits received by the person or property taxed; taxation should be based on ability to pay. A third is sometimes added, taxation should have reference to the extent and value of the natural resources enjoyed. As applied to mining taxation, it is pointed out by those who support the fist mentioned basis that, mines being usually situated in rocky and hence sparsely peopled regions, mining companies are frequently obliged to construct roads, railways, telegraph and telephone lines, schools, water and sewerage systems, and many other amenities and conveniencea of civilization the cost of which in regions better suited for agriculture, and consequently more thickly populated, has either been defrayed locally, or can be spread over a sufficiently large taxable group of people to materially lighten the financial burden on the mine. The mining company, it is argued, having made these outlays, should receive credit for them and be relieved of taxation to a corresponding extent. There may be some force in this contention, but the situation is capable of relief without attempting to place taxation upon so unworkable a basis as the value of benefits received. Who is to be the judge of these benefits, and how are they to be valued? The very existence of a mining company and its ability to carry on business in peace and security depeind on the prevalence of law and order, which is a result of good government. The state provides protection against violence, and courts of law for

Jan 1, 1920

By Carle R. Hayward

This work was first undertaken in the metallurgical laboratory of the Massachusetts Institute of Technology in 1907 by L. A. Dickinson, E. Phelps, and V. S. Rood, under the author's direction. They attempted to determine the diagram for the system Cu2S-MiS, but several inexplicable results were obtained. The following year, P. H. Mayer with Mr. Dickinson carried on some experiments with nickel sulphide and found that the molten material slowly lost sulphur until it reached a composition corresponding to the compound Ni3S2, established by Bornemann.l At this point the composition remained stable. The freezing points of the mixtures gradually fell off with the loss of sulphur. Since the above facts seemed to explain the erratic results obtained in the first experiments, Mr. Mayer with F. Jaeger attempted in 1910 to establish a correct equilibrium diagram for the Cu2S-Ni3S2 series. They prepared pure Cu2S and Ni3S2 and determined the cooling curves for various mixtures. The fusions were made in a platinum resistance furnace and the temperatures were measured with a platinum-iridium thermocouple connected with a Sullivan galvanometer. The curve was established for mixtures containing more than 40 per cent. Cu2S, but they were unable to determine certainly the direction of the curve beyond that point. Nothing further was attempted with this series until the present year, when the work was carried to a successful conclusion with the assistance of A. Butts, Jr., and E. H. Weil. The results of this work are given in the following pages. Preparation of Cu2S.—A piece of cathode' copper from the Buffalo plant of the Calumet & Hecla Co. was cut into shavings by a shaper and converted into sulphide by heating in boiling sulphur. A porcelain casserole was used for the purpose, the heat being furnished by a Bunsen burner. It was found that after boiling in the sulphur for an hour the copper shavings were completely converted into sulphide. The liquid sulphur was then poured off, leaving the solid sulphide in the casserole in

Jan 1, 1915

By Enid C. Plante

To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), rnarcasite (FeS2), orpiment (As&.), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also exarnined to determine if its behavior could be correlated with that of pyrite or rnarcasite (FeS2. Experimental Method Mineral for Flolation and Contact Tests Mineral was prepared in the manner a1ready described1 and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and CO2-free air bubbled through each suspension at a constant rate (about I bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation , oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the 'supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.l No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 Flotation of "Unoxidized" Minerals with Ethyl Xanthate as Collector Fig I to 3, 4. 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox8 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1949

By Charles A. Ashburner

The petroleum industry of western Pennsylvania and southwestern New York lias been one of phenomenal development. Greater and more sudden flucuations hare occurred in the price* of crude oil, and in all the collateral interests dependent upon its production, than in the case of any other mineral product which has been extensively exploited in the United States. This was more particularly so from the commencement of drilling for oil in 1859 down to the end of 1877. The experience gained during these early years has enabled the oil men to operate more intelligently since; the business is not now attended with the hazardous risks with which it is generally credited. The most important questions connected with the oil industry are those of (a) the oil-supply, and (6) the possible ultimate exhaustion of the field. Since 1876 my attention has been directed to the study of the statistics of the product of the oil regions. In January, 1880, in order to slow some interesting points connected with these questions, I prepared a graphic chart which was used to illustrate a lecture on petroleum delivered before the Franklin Institute. This chart was afterwards reconstructed in two distinct forms for publication in the census report. on Petroleum and its Products. These latter I have redrawn in a condensed form, and have extended them to include the statistics up to 1885, for publication in the Transac tions of the Institute, in conjuction with a map of the oil-re&'~IOIIS prepared by Mr. John F. CarII and myself. It is hoped that these illustrations will be found interesting to the members of the Institute, and of practical utility to oil-men, without any extended discussion, since it is my desire to make only such brief references to them and give such additional detailed facts as may serve to make the prominent features understood.

Jan 1, 1886

C. W. GOODALE, * Butte, Mont.-In regard to the employment manager, the North Butte Mining Co. has undertaken that line of work and the rest of the companies are watching the experiment. If it is proved to be the proper thing, the system will be introduced into other mines. We have to combat the opposition to the use of the "rustling card. It is nothing more nor less than asking the nationality, where the plan formerly worked, and whether he is married or single. ROBERT RHEA GOODRICH, Anaconda, Mont. (written discussion?).¬Since the efficiency of the different phases of personnel work employed by industrial concerns, which are bringing about greater efficiency and lessening the labor turnover, the latter being intimately connected with "contentment of mind," depends on the individual workman, it is highly desirable, as far as industry is concerned, to keep the workman's mind and body in trim in order to lessen accidents and produce a higher grade of work. Prevention being better than cure, health supervision of the workmen during employment should be maintained by the employers in order that mental alertness and physical well-being may be obtained. I have long believed, from observation in many plants, that when any problem is dependent on the individual workman, what he believes and what he does is vitally dependent on his health. I will follow with much interest what is to be clone in the future in relation to the subject of health supervision during employment (as well as medical examinations at the time of employment), and I hope this idea will be generally instituted in personnel work. A workman with good health and a contented mind should be an ideal component of a progressive industrial concern. The contentment of the workman is fostered by a number of admirable phases of welfare work which are being still further developed. The mental and physical well-being of labor should be the issue in Labor vs. Capital in the new period of the industrial promotion of the United States into which we are now entering.

Jan 4, 1919

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the 'economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40' above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

By Henry N. McCarl

Mineral aggregates are those natural and manufactured industrial mineral and rock materials that provide bulk and strength in port- land cement concrete, bituminous concrete mixes, and plaster or stucco surfaces. They may also provide special characteristics such as thermal and acoustical insulation, weight, surface textures, abrasion resistance, and impermeability to various concrete products and mixes. Most aggregates are relatively inexpensive materials, but despite their low unit value, the tonnages consumed each year in the United States and throughout the world make mineral aggregates by far the leading industrial mineral and rock materials both in terms of volume (tonnage) produced and value consumed. The major use of mineral aggregates is in concrete. The low cost, high bulk aggregates tend to keep concrete construction costs at levels competitive with other building materials. Other major uses of aggregates include highway and railroad base or ballast materials, graded fill, and various industrial uses such as metallurgical and chemical fluxes and raw materials-these latter uses are often considered nonaggregate uses of mineral aggre- gate materials. The value of mineral aggregate materials at the production plant varies from less than a dollar per ton to several dollars per ton for most crushed stone and sand and gravel, $2 to $15 per ton for slag and expanded clay or shale aggregate, to as much as $60 to $100 per ton for expanded perlite or vermicu- lite. The more specialized the use, the higher the price-although there are naturally some exceptions to this rule of thumb. The first four parts of "Construction Materials" deal with the utilization of four major mineral aggregate types: Crushed Stone, Light- weight Aggregates, Sand and Gravel, and Slag. While the focus will be on the use of these industrial minerals and rocks there will also be some coverage of sources, mining and production, especially in those cases where they are

Jan 1, 1975

Separates of all the Technical Publications published in 1931 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the Transactions. Copies of these papers have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division; G-Petroleum Division; H-Nonmetallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Additional copies are sold at the rate of I cent per page; minimum charge, 25 cents. Metal Mining Tech-nical Publi- Title Author Meeting TRanb. cation Volume No. and Page* 411-A.43 Ventilation at the Portovelo Mines, J. P. Harmon New York. T31, 83 Ecuador (18) Feb., 1931 425-A.44 Use of Models for the Study of Mining P. B. Bucky New York, Problems (28) Feb., 1931 Milling and Concentration 375-B.32 Ball Mill Studies, I (53) A. W. Fahrenwald New York, H. E. Lee Feb.. 1931 401-B.33 Experimental Flotation of Oxidized H. S. Gieser New York. Silver Ores (9) Feb., 1931 410-B.34 Flotation of Minor Gold in Large-scale E. S. Leaver New York, Copper Concentrators (32) J. A. Woolf Feb., 1931 414-B.35 Effect of Particle Size on Flotation A. M. Gaudin New York, (23) J. 0. Groh Feb., 1931 H. B. Henderson 416-B.36 Ball Mill Studies, 11.—Thermal A. W. Fahrenwald New York. Determinations of Ball Mill Effi- G. W. Hammar Feb., 1931 ciency (13) H. E. Lee W. W. Staley Iron and Steel Division 38QC.59 Open-hearth Steel Process as a Prob- E. R. Jette New York, C31, 80, 111 Iem in Chemical Kinetics (34) Feb., 1931 381-C.60 Thermodynamic Study of the Phasial Yap, Chu-Phay New York. Equi1ibriain the System Iron-car- Feb., 1931 bon (26) 382-(3.61 Influence of Dissolved Carbide on the Yap, Chu-Phay New York, Equilibria of the System Iron-car- Feb., 1931 ban (19) 383-C.62 Research on Blast-furnace Slags. R. S. McCaffery New York, Three papers (88) Co-workers Feb., 1931 384-C.63 Statistical Analysis of Blast-furnace K. S. McCaffery New York, C31, 60, 70 Data (13) R. G. Stephenson Feb., 1931

Jan 1, 1931

By Martin T. Broome

INTRODUCTION The Luanshya Mine is situated in the southern part of the Zambian Copperbelt. The copper ore deposit is stratiform, and is preserved in a synclinorium known as the Roan/ Muliashi basin. Roan shaft (formally called No.14 shaft) is located at the eastern end of the syncline and is theoldest of the presently operating hoisting shafts, being sunk during the 1930's. It presently hoists some 45 per- cent of the total Luanshya Mine production. A cross-section through the shaft is shown in figure 1. The ore formation on the south limb is unmined on this section because until recently it was believed that such mining might cause damage to the shaft. This paper examines the influences of adjacent mining on this so-called 'shaft pillar', and describes the mechanics of subsidence of the pillar itself. GEOLOGY AND STRUCTURE Figure 1 shows the general form of folding in the vicinity of Roan shaft. The north and south limbs of the main syncline approach parallelism, with the bottom of the trough fairly smoothly rounded. The axis of the - trough plunges to the west-north-west at 6° - l0°. A brief summary of the major lithologies present in the Roan basin is given in table 1, however, the performance of the overall structure during progressive mining of the ore horizon is controlled by the following features in addition to the mining method. Intraformational Contacts These are characteristically weak in most geological environments. The BC/RL7 contact is an unconformity between moderately weak quartz-biotite schists below (unconfined compressive strength 40 - 80 MN/M 2), and strong quartzites above (U .C .S. 170-200 MN/M2) Subsequent formations are conformable, and planes of weakness are generally the result of contrasting lithology (see below). Weak Interbeds The Rt7, RL6, RL5, RL3 and RU2 horizons consist predominantly of quartzitic rocks, i.e. conglomerates, quartzites and argillites, and as such are generally strong and considered suitable for the positioning of development. Between these however, lie two much weaker dolomitic horizons, the RL4 and RU1. The Rt4 is the main hangingwall aquifer, and must be drained prior to mining. Drainage results in an extremely weak, blocky cavernous horizon which usually requires support if exposed by development. Similarly, the RU1 formation is comprised mainly of dolomites and dolomitic arqillites which are weak and cavernous. In the eastern part of the Roan/

Jan 1, 1981

By Blake M. Caldwell, Thomas C. Poulter

A new approach to an old problem has made it possible to do in a a tively short period what has not been accomplished in the past three quarters of a century using strictly experimental methods. A theoretical study was made of the underlying principles whereby a jet is formed by a shaped charge and of the mechanism of the penetration of the target by that jet. It was found that there are more than 10, and perhaps as many as 15 variables affectin!? the performance of the shaped charge. Only a few calculations are necessary to show that it is physically impossible to investigate all of these variables experimentally. The shaped charge theory has been extended to include a previously little-understood mechanism in high explosive phenomena; namely, low order detonation. By superimposing a high order detonation on a zone already undergoing low order detonation, all appreciable improvement in performance is accomplished. The development of a design wherehy these phenomena are coordinated in such a way as to develop a jet which is tailored to meet the specific target requirement will be described in detail. The shortcomings or even impossibility of strictly experimental techniques will be illustrated by a discussion of the development of a special-purpose explosive charge. INTRODUCTION In an article appearing in the May, 1888 issue of Scribner's Magazine, Charles E. Monroe described his early experiments with gun cotton (Fig. 1) which led to his name being most fre-quently connected with our present-day shaped charge. Although the sunken letters or "cavities" in Mon- roe's gun cotton were not lined, they produced some penetration of an iron plate. The credit for the lined shaped charge, however, should rightfully go to Dr. R. W. Wood of the Physics Dept. of Johns Hopkins University, who was responsible for first discovering the fact that a metal liner in a cavity of explosive gave high velocity fragments and/or jets of metal. This discovery was made by Dr. Wood inadvertently while investigating an accidental death resulting from an electric blasting cap. He discovered that a jet of high velocity copper particles was ejected from the dimple

Jan 1, 1958