Search Documents

By T. H. Alden

BaCKOFEN, Avery, and Turner have shown"2 that the large tensile elongation in superplastic metals is correlated with a high strain-rate sensitivity of the flow stress. At present, the reported superplastic materials are complex eutectic or eutectoid systems with a large solubility range in at least one of the terminal phases. This note describes the behavior of a solid-solution alloy (at 22°C)5,= Sn-1 wt pct Bi, which has been processed in order to produce a fine grain size.2,3,6 The chill-cast, 1/2-in.-diam ingot was homogenized for 1 week at 130°C, extruded at O°C to 0.083 in. diam, quenched within 15 sec, and stored at -196°C. Samples were warmed to room temperature 16 hr prior to mechanical testing or metallography. During tension testing at room temperature, it was found that the flow stress reached a steady-state value which depended on the imposed elongation rate and was independent of strain to an error of about ±5 pct. In Fig. 1 is plotted log a vs log e where a is the measured steady-state flow stress and i the imposed strain rate. These quantities were calculated using "instantaneous" area and length to an accuracy in the sample diameter of ±5 x 10-4 in. The log a-log 1 curve is sigmoidal. The strain-rate sensitivity, which may be given by d log old log 6,' has a maximum value of about 0.48 between i = 5 x 10-4 and 5 x 10-3 per min. The value is well above frequently measured values for metals at creep temperatures (0.1 to 0.3) and comparable to the rate sensitivity for Pb-Sn solder: which has been shown to be superplastic.2,3 Note, however, that below or above the strain rate of 10-3 per min the rate sensitivity of Sn-1 pct Bi decreases and at high rates is more nearly like that of conventional metals. The grain size of this material is relatively uniform, Fig. 2, and may be specified by an average linear intercept i.' Grain growth occurs at room temperature but after 16 hr, L = 5. Tensile elongation was measured on finer-grain-size specimens, which had been at room temperature 15 min prior to testing. After 15 min, the samples are fully recrystallized. Three strain rates, 5 x 10-3, 10-2, and 2.5 x 10-2 per min, were employed for which the measured elongations varied from 425 to 500 pct. These results would seem to justify the term superplastic, applied to this alloy, although the ductility is inferior to that of the Sn-Bi eutectic.3 The Sn-1 pct Bi alloy, which is a single-phase material with equiaxed, fine grains, is an excellent one on which to make an estimate of the Nabarro-Herring9 creep rate. According to the model of Avery and Backofen2 a substantial part of the deformation must be accomplished by N-H creep in the strain rate-temperature regime in which d log a/d log 1 = 0.5. The maximum N-H creep rate is given by9 L2kT where v is the atomic volume and D the self-diffusion coefficient. For this test v = 3.O x 10-23 cu cm, D = 1.4 e-23,300/RT = 2.5 x 10-l7 sq cm per sec,7 L = 5x 10+4 cm, T = 295°K, and a = 2000 lb per sq in. = 1.38 x 10' dyne per sq cm. The calculated creep rate is E= 4 x 10-11 per sec which may be compared with the measured creep rate at this stress, Fig. 1, of 6.7 x 10-5 per sec. The N-H creep rate is seen to be negligible. Earlier consideration2 of this question was in error because incorrect diffusion coefficients were used. The assistance of R. R. Russell in metallography is acknowledged gratefully.

Jan 1, 1967

By William H. Spice

The fault zone of south central Texas showed renewed activity during I940 along a trend roughly paralleling the old established Balcones fault-line group of producing fields. This was a result of the new discoveries in the Wilcox (Eocene) formation in southeastern Texas and Louisiana. As of the end of the year, one new field producing from the Wilcox formation had been discovered on the Washburn ranch in La Salle County, along the southwestern limits of the district, and several projected tests into that formation were under way. In the western part of the district, par-titularly in the part of the Rio Grande embayment that is in Dimmit, Webb and Zavala Counties, there has been renewed leasing activity with the shallower sands in the Navarro-Taylor formations (Upper Cretaceous) as the objective in several projected tests for the early part of 1941. Three new fields have been discovered along the old fault-line trend, but these have been comparatively small, producing either from Dale lime, Austin chalk or Buda lime. No new fields were discovered during the Year in the Edwards (Lower Cretaceous) lime horizon. Approximately 260 wells were drilled in the district during 1940, which resulted in four new oil fields. Twenty-seven new wells were completed in the Proven Edwards lime fields of Darst Creek, Luling and Salt Flat and seven were added to production in the Pearsall field. Approximately 160 wells in 18 counties were completed as failures during the year. The district produced 7,659,634 bbl. during 1940, which was a 9 per cent decrease under production for 1939. In all, 3559 wells were producing at the end of I940, compared with 3562 wells producing at the end of the previous year; 104 new producing wells were completed and 163 wells were abandoned in the producing fields of the district. During 1940 considerable exploratory work was carried on along the Wilcox trend within the district, particularly by major companies employing various types of geophysical methods, and leasing activity increased considerably. At the end of the year, the total number of acres of nonproducing leases held by major companies in the district increased about 10 per cent. It is anticipated that this activity will continue into the first part of 1941 and will be supplemented by several exploratory test wells. New Fields B,, Creek, Caldwett County.— . R. Ogden NO. 2 Talley, discovery well of the Bee Creek field, in the northeastern part of Caldwell County, was completed on March 16, I940, in Dale lime from 2091 to 2238 ft., pumping 85 bbl. per day, 39° A.P.1. gravity. The discovery of this field can be credited to a combination of subsurface geology and magnetometer work, which indicated the presence of a serpentine intrusion. At the end of the year, ,3 producing oil wells had been completed and the field has produced a total of 47,050 barrels.

Jan 1, 1941

By William H. Spice

The fault zone of south central Texas showed renewed activity during I940 along a trend roughly paralleling the old established Balcones fault-line group of producing fields. This was a result of the new discoveries in the Wilcox (Eocene) formation in southeastern Texas and Louisiana. As of the end of the year, one new field producing from the Wilcox formation had been discovered on the Washburn ranch in La Salle County, along the southwestern limits of the district, and several projected tests into that formation were under way. In the western part of the district, par-titularly in the part of the Rio Grande embayment that is in Dimmit, Webb and Zavala Counties, there has been renewed leasing activity with the shallower sands in the Navarro-Taylor formations (Upper Cretaceous) as the objective in several projected tests for the early part of 1941. Three new fields have been discovered along the old fault-line trend, but these have been comparatively small, producing either from Dale lime, Austin chalk or Buda lime. No new fields were discovered during the Year in the Edwards (Lower Cretaceous) lime horizon. Approximately 260 wells were drilled in the district during 1940, which resulted in four new oil fields. Twenty-seven new wells were completed in the Proven Edwards lime fields of Darst Creek, Luling and Salt Flat and seven were added to production in the Pearsall field. Approximately 160 wells in 18 counties were completed as failures during the year. The district produced 7,659,634 bbl. during 1940, which was a 9 per cent decrease under production for 1939. In all, 3559 wells were producing at the end of I940, compared with 3562 wells producing at the end of the previous year; 104 new producing wells were completed and 163 wells were abandoned in the producing fields of the district. During 1940 considerable exploratory work was carried on along the Wilcox trend within the district, particularly by major companies employing various types of geophysical methods, and leasing activity increased considerably. At the end of the year, the total number of acres of nonproducing leases held by major companies in the district increased about 10 per cent. It is anticipated that this activity will continue into the first part of 1941 and will be supplemented by several exploratory test wells. New Fields B,, Creek, Caldwett County.— . R. Ogden NO. 2 Talley, discovery well of the Bee Creek field, in the northeastern part of Caldwell County, was completed on March 16, I940, in Dale lime from 2091 to 2238 ft., pumping 85 bbl. per day, 39° A.P.1. gravity. The discovery of this field can be credited to a combination of subsurface geology and magnetometer work, which indicated the presence of a serpentine intrusion. At the end of the year, ,3 producing oil wells had been completed and the field has produced a total of 47,050 barrels.

Jan 1, 1941

By AIME AIME

0 N March 5, at Carnegie Hall, Cleveland, the Ohio Section held a joint meeting with the Cleveland Engineering Society, and the local sections of the American Chemical Society, American Society of Mechanical Engineers, and the American Society for Steel Treating. Prior to the meeting there was an informal dinner attended by 50 men. Then followed an address, "The Principles of Corrosion Protection," by Ulick R. Evans, the well-known British specialist in this problem. There were 266 present, presided over by Zay Jeffries, president of the American Society for Steel Treating and a member of the Cleveland Engineering Society. The address was well received and some discussion followed

Jan 1, 1929

By C. W. Allen, L. C. Moore

THE Mather mine, of the Negaunee Mine Co., is within the limits of the City of Ishpeming, on the Marquette iron- range in Michigan's Upper Peninsula. It is named for William G. Mather, who has served as President, and Chairman of the Board, of The Cleveland-Cliffs Iron Co. for well over 50 years. The property comprises nearly the square mile of section 2, T.47 N. R.27 W., which, except for 20 acres in the northeast corner, was leased by The Cleveland-Cliffs Iron Co. to the Negaunee company. The latter is a partnership of Cleveland-Cliffs and the Bethlehem Steel Co., organized to equip the property, retaining Cliffs in charge as operator. Shipments of ore from this area are mainly through Marquette, which is 16 miles to the northeast on Lake Superior, or through Escanaba, a Lake Michigan port, 65 miles to the south. Cleveland-Cliffs, in 1943, operated 12 mines in the Lake Superior district, with shipments of 6,635,576 tons for the year. GEOLOGY The north footwall of the Marquette Range synclinorium outcrops near the north line of sec. 2, the iron formation dipping to the south at an angle of about 40º. The south side of the trough reappears at a distance of 4 ½ miles on sec. 26 and the surface geology between shows iron formation or intrusive diorites. The latter are harder than most phases of the iron formation and, as a result of glacial action, appear as buttes or low-lying hills. The general elevation of sec. 2 is about 1450 ft. above sea level, or 850ft. above Lake Superior, and the higher diorite outcroppings about 1600 ft. above sea level. The geological structure has been complicated by a series of major and minor faults, one of which may be illustrated by the diorite sheet, which tilts south with the iron formation in the north half of the section and then reappears near the center to repeat this sequence. Sectionally the geological series includes a nearly eroded capping of Goodrich quartzite followed by the considerable thickness of Negaunee iron formation, which is cut by intrusive dikes or diorite sheets, and underlain by the Siamo slates grading into quartzites. The ore deposits occur mainly in troughs formed by the intersection of impervious dikes and the footwall slate, but include locally enriched lenses or bands in the iron formation and also interbedded with the Siamo slate. The ore is a soft red hematite with an indicated dried analysis from the surface drilling to date of 61.50 per cent Fe, 0.134 per cent P, 5.40 per cent Si, 2.87 per cent Al and 0.015 per cent S. EXPLORATION A diamond-drilling campaign started in 1937 actually had its inception in 1917, when a number of shallow test holes were put down for the purpose of locating ore that might be quickly developed and mined

Jan 1, 1945

By George Smith

IN discussing present-day business and industrial troubles we easily drop into the habit of clinical diagnosis. Talk of this kind, with its emphasis on suspicious symptoms and abnormal tendencies, makes us all morbid. As an English essayist has put it, we may thus induce a melancholy, temper that simply in-vites the ministrations of social and political quacks. It is far better-because nearer the truth-for us to recognize that our condition is in no sense diseased, that our body politic, social and economic, is suffering merely from growing pains; that America is not de-cadent-indeed, that any lapses from staid normality are traceable to the, excesses of youth. Our chief .trouble, then, is only that our industrial state is still young; it may be that we have been growing too fast. The growth in the industrial development of our country from pioneer days to the present time has been marvelous. Too many of us, however, take all this as a matter of course-we credit this record of American progress to our American genius alone. Too often we overlook the fundamental relationship between resources and progress-that man is aided and even guided by Nature. The fact is, social advance, indus-trial progress, national prosperity all have their ma-terial basis in natural resources. In furnishing the needed mineral raw materials to the great manufac-turing industries of the United States there has been no halt, but rather a general acceleration. No other phase of American activity can show-equal advance. As the decades have passed, the winning of mineral wealth has progressed from the role of a stimulus for western exploration to that of the foundation for nation-wide business. In 1890 the Sherman law was passed; since then the population of the United States has about doubled. Since then, too, thevalue of the annual product of the mines of this country has increased better than eight-fold-from 650 millions to 51/ billions of dollars. Since then the four largest branches of the mineral industry, which supply the iron and copper, the bituminous coal and petroleum-the bone and sinew and the energy of all other American industries-have increased their annual output nearly ten-fold as to value and six-fold as to quantity. Such a growth in the volume of mineral output must be taken as a true measure of the ex-ceptional service rendered by the mines of the United States. Not only is this a much larger country than it was 38 years ago, but its growing mineral industry has met demands that have been out of all proportion to the growth of the population.

Jan 8, 1928

T. H Aldrich '96 Walter H. Aldridge '89 R M. Atrater, Jr '97 James B Bailey '00 Samuel Barker, Jr. '00 John F Berry '93 Charles A Bohn '93 H. A Brassert '99 Victor B. Buck '98 Frederick Burbidge '87 Frederick P Burrall '97 John Cabot, Jr '99 William McC. Cameron '97 W Gaston Caperton '94 Norman Carmichael '99 Alvin B. Carpenter '97 Charles A Chase '00

Jan 1, 1952

By P. A. Fisher, J. B. Wilson, D. J. Whitehead, C. J. P. Ball, A. C. Jessup

The properties of a new magnesium alloy ZT1 containing 3.0 pct Th, 2.5 pct Zn, 0.7 pct Zr are described. The alloy possesses good creep and fatigue resistance up to 650°F, is free from microporosity, and is readily sand-cast. ZT1 is shown to be superior to zinc-free Mg-Th-Zr alloys. THE advent of the jet engine created a demand for a light sand-casting alloy capable of being cast into large complex shapes and capable of resisting creep at temperatures up to 500°F. This demand has been largely met by alloys of the magnesium-cerium mischmetal-zirconium types, containing about 3 pct Ce mischmetal and 0.7 pct Zr, typified by Elektron magnesium alloys MCZ and ZREI, the latter alloy also having a zinc addition of 2.5 pct. These alloys utilize the valuable properties at elevated temperatures conferred by the addition of rare earth metals to magnesium, a fact which has been known for many years and discussed by several investigators.1-1 Murphy and Payne8 showed that the addition of the powerful grain-refining element zirconium to Mg-Ce mischmetal alloys produced alloys with attractive room temperature properties combined with good creep properties and castability. With the increasing power of modern jet engines the temperatures to which some of the magnesium parts are subject are likely to exceed the safe working range of the cerium-mischmetal-containing alloys, and at the beginning of the research considerable interest had been shown by aeroplane engine designers in a magnesium sand-casting alloy suitable for service at higher temperatures, e.g., 600°F and above. At an early stage in the development of this type of alloy a check on the fatigue properties at elevated temperatures indicated that, since the fatigue limit even at 108 eversals was appreciably higher than any permissible creep stress, the main emphasis of the research could be concentrated on creep behavior. The primary aim in developing the new alloy has therefore been to attain maximum creep resistance; but due consideration has also been given to other important properties such as castability, tensile strength, and cost. It is by now well established that it is not possible to correlate creep strength with other short time mechanical properties such as are obtained in tensile

Jan 1, 1954

By S. Fugleberg

As a result of research work done during the planning of the Kokkola zinc plant it was found that a very efficient cementation of impurities from the suspension obtained after leaching copper and cadmium cakes was achieved by adding zinc dust to the batch without filtration after the leaching. All elements nobler than cadmium are precipitated with the exception of lead, which must be removed in a separate step. Using pure zinc dust, free from noble metals, the cadmium sponge produced will only contain elements that can be re- moved from cadmium by meltrefining. The process is thus : 1. Leaching and purification 2. Removal of lead (with BaCO3) 3. Precipitation of cadmium sponge with pure zinc dust 4. Meltrefining of briquetted sponge with NaOH for removal of Zn (and others) The paper deals with the removal of the most critical elements, i.e. Co, Ni, As, Sb, Cu, Pb, T1 in the liquid phase and Zn and T1 in the melt. A survey is also given of the behaviour of most of the other elements normally found in Cd raw material, such as Ge, Te, Se, Sn, In, Ga. It is shown that in most cases the benefit of an electrolysis in Cd production is very limited. In Kokkola 99.998% Cd is achieved by this method, but in favourable cases it may be possible to come quite close to five nines.

Jan 1, 1973

By AIME

Annual production of more than 4,000,000 tons of 0.74 percent copper ore and coincident handling of over 5,000,000 tons of waste at the open-pit mine of Castle Dome Copper Co. near Miami, Ariz. takes a lot of power. Manufacturers have ever co-operated with mining companies in providing the required equipment to suit the problem. Power equipment suppliers have done much to make possible the economic and profitable production of copper from low-grade ores. In the future, as mining operations will necessarily handle even lower-grade ores, the ability of the manufacturer to supply the power and mechanical equipment to produce more metal at a fair and reasonable price will be the good right arm of the miner. About 27,000 tons of concentrate is produced from the 4,000,000 tons of ore.

Jan 1, 1948

By S. F. Reiter, You-Chao Liu, W. R. Hibbard

Cyril Stanley Smith in his classic 1948 Institute of Metals Lecture&apos; noted in the case of annealing twins that: "It is well known that approximately the same number of twins per grain and the same general geometry are maintained in large grains as in small ones, a fact that certainly suggests a mechanism such as the above where boundaries and twins grow proportionately together. If this view is correct, a spherical grain should have no mechanism for keeping its twins." Such a constancy of twins per grain would be of particular interest as a tool for the study of the origin of annealing twins. It has been proposed by Mathewson2 and later by Barrett3 that in face-centered cubic metals slip occurs in the {111} Plane by <112> shears which combine in pairs to produce the macroscopically observed <110> movement. This proposal is schematically inviting since <112> slip permits the atoms of one plane to move along the interatomic valleys of its neighbor rather than up the hills across the atom sites. There is strong experimental evidence? that annealing twins result from the growth of nuclei in the form of "twin faults" produced by single <112> shears. It is possible that more twin faults would form at low deformation temperatures than at high ones, because the more rigid lattice may increase the tendency to "freeze" the twin faults and prevent their dissipation in slip. This is suggested by (1) the greater resistance to slip at low temperatures and (2) greater tendency toward mechanical type twinning at low temperatures (a summary of these factors is presented by Seigle and Brick5). These considerations would suggest the following: a. Constant twin/grain ratio for specimens deformed constant amounts at a constant temperature, but annealed at various temperatures above the recrystalliza-tion temperature. b. Larger twin/grain ratios for re-crystallized specimens previously deformed constant amounts at lower temperatures. The purpose of this investigation is to test these considerations. One half in. rods of phosphorous deoxidized electrolytic copper and 70-30 alpha brass (68.36 pct Cu, 0.005 pct Pb, 0.01 pct Fe, 31.62 pct Zn remainder) were rolled to a thickness of 0.350 in., milled to specimens 0.350 X 0.437 X 2 in., and annealed at 700°C to an average grain size of 0.065 and 0.090 mm, respectively. These specimens of each metal were then rolled 50 pct reduction in thickness and annealed one hour under conditions which were all combinations of the following: Rolling Annealing Temperatures. Temperatures. °C °C -70 400 25 500 200 600 Standard metallographic techniques&apos; were used to prepare specimens. By the method of lineal analysis7 using a minimum of ten samples of fifty grains each for each specimen, the ratios of twins* per total grains, twins per twinned grain, twin families* per total grains and twins per twin family were determined. Recrystallized grain size was determined by A.S.T.M. comparison methods.8 All observations were made on the rolling plane. The results are tabulated in Table 1.

Jan 1, 1950

By M. E. Wadsworth

The chief value of a paper like this consists in its statistical tables, putting on record material useful to future inquirers. The data here given have been compiled from time to time as far back as 1874, and subsequently brought up to date. Much of the data could only be procured by personal inspection of the catalogues, as for example those relating to the Lawrence Scientific School, which were taken at that time from the catalogue of Harvard University, on file in the University Library, by the present writer, then an instructor in that institution. These tables of statistics were first prepared for publication by the present writer in 1888-1890 and published in his "Report to the Board of Control of the Michigan College of Mines " (Michigan Mining School) for 1886 to 1890. Later they were revised, enlarged and brought down to date in his reports to the same Board for 1890-92; and since that time they have been, at his request, revised, greatly enlarged and kept up to date by Mrs. Frances H. Scott, the efficient Librarian and Secretary of the Michigan College of Mines. Great credit is due to her for her devotion to this work and her untiring efforts to have the statistics complete as far as possible. The accompanying running commentary is given simply as a string to hold these statistics together, and in order to call attention to a few points. In compiling any tables like those accompanying this paper, one is confronted by serious difficulties, some of which render these results only approximate. In order to insure greater correctness and fullness in the statistics to be published the writer&apos;s reports for 1890-92 were sent to the president of every college, university, and technical school in the country, so far as known. Accompanying this was a personal letter which asked of each one his aid in correcting any errors, and in giving fuller statistics. But relatively few answers were obtained, and subsequently from one to many letters have been sent to each institution not formerly reply-

Jan 1, 1898

For the benefit of those of our members who are considerable holders of securities,but owing to their isolated situations are not in close touch with the metropolitan market and current quotations, we are publishing two very interesting graphs, showing the course of the bond and stock markets in New York over a long period. These graphs are furnished through the courtesy of the financial department of the New York Tribune.

Jan 11, 1919

By F. B. Foley

A description of tests made by a committee of the Division of Engineering of the National Research Council to determine whether velocity of impact affects the formation of Neumann bands. FOREWORD Not infrequently, in the case of the failure of a metal structure, such as a bridge, tank, airplane, gun carriage, etc., a doubt arises whether the failure was due, among other causes, to the effect of an overburden or of an explosive maliciously or accidentally exploded in contact with it. As few means of discriminating between the effects of these causes have been known and these means were of a rough qualitative character, it was surprising to find in the record of an inquiry into the failure of a structure, the statement that, by observations on the Neumann bands in the structure, it was possible to determine the speed of breakage in the metal and to distinguish between a fracture caused by an explosion and one caused by an ordinary mechanical strain. Such a criterion, if well proved, was of value to the explosives experts of the Bureau of Mines, the Ordnance Department of the United States Army and the Bureau of Ordnance of the United States Navy, but search showed no record of it in the literature nor did any of the metallurgists and metallographers consulted know of any data on which such a criterion could be based having been assembled and critically studied. However, it was universally held that there was promise in the idea and that there existed unique facilities at the Bureau of Mines Experiment Station at Pittsburgh for the preparation, under definitely known conditions, of material for study by metal-lographers, and that material of value might also be obtained from the proving grounds of the Army and Navy. Therefore, with the approval of the Director of the Bureau of Mines and the Chiefs of Ordnance of the War and Navy Departments, the Chairman of the Division of Engineering of the National Research Council, on April 12, 1919, appointed a Committee on the Investigation of Neumann Bands, which has since been engaged in this study and which, after some slight change in its personnel, consists now of the following: Dr. William Campbell, Advisory Metallurgist, Bureau of Ordnance, Navy Department. F. B. Foley, Metallurgist, Bureau of Mines. S P. Howell, Explosives Engineer, Bureau of Mines. Comdr. O. M. Hustvedt, U. S. N., Bureau of Ordnance, Navy Department. Dr. Charles E. Munroe, Chief Explosives Chemist, Bureau of Mines.

Jan 9, 1922

THE first session of this meeting was held Tuesday evening, in the chamber of the Common Council, the President, Mr. David Thomas, in the chair. Mayor Carroll, of Troy, gave a cordial welcome to the Institute, which was responded to, on behalf of the Institute, by the first Vice-President, Mr. R. W. Raymond. The Council reported the names proposed for membership with recommendation for election. The following named gentlemen were duly elected: Anthony, J., . .Williamstown, Pa. Babcock, George, . . .Troy, N. Y. Blake, Theo. A., . . . . . . Sa n Francisco, Cal. Blossom, T. M., . . . . . . New Pork. Boalt, James A., . . .San Francisco, Cal. Bowman, Amos, . . . . San Francisco, Cal. Chester, Prof. A. H., . .Clinton, N. Y. Dewey, C., . Pittsfield, Mass. Dock, Gilliard, . Shamokin, Pa. Emerson, O. D., . .New York. Endres, John J., . .Pittsburgh, Pa. Firmstone, Frank, . Easton, Pa. Fowle, W. B., . Philadelphia, Pa. Frazier, Prof. B. W., . . .Bethlehem, Pa. Gardner, George A., . New Pork. Goodyear, Watson A., . .6an Francisco, C al. Griswold, Chester, . Troy, N. P. Griswold, J. A.,* . . .Troy, N. Y. Hague, J. D., . . .San Francisco, Cal. Hahn, 0. H., . .Eureka, Nev. Harkness, T. C., . . . . . . Wilkes-Barre, Pa Harris, Samuel, . . .Hudson, N . Y. Henry, &. T., . Oxford, N. J. Holley, A. L., . .Brooklyn, N. Y. Howe, H. W., . . .Troy, N. Y. Hunt, Dr. T. Sterry, . Boston, Mass. Jannet, J., . Troy, N. Y. Knapp, John A., . .New Pork. Laughlin, Henry A., . . .Pittsburgh, Pa.

THE great event in American affairs was the sudden death of President Harding, on Aug. 2, in San Francisco. A few hours later Vice-Presi¬ dent Coolidge took the oath of office while in his father&apos;s farmhouse in Vermont and forthwith proceeded to Washington as the 30th president of the United States. The French and Belgian governments&apos; replied to the British refusing the proposed discussion of the German offer and declaring that they would pursue their policy in the Ruhr until the German government abandoned its resistance and surrendered unconditionally. The economic collapse of Germany .appears to be nigh. Chancellor Cuno and his cabinet resigned the govern-ment of Germany on August 12, and Gustav Strese-mann, head of the People&apos;s party, accepted the task of forming a four-party coalition government. Coinci-dentally, there were food riots throughout Germany, and many persons were killed and wounded. The , National Assembly of the Turks at Angora ratified the Lausanne treaty, in the latter part of August, whereupon the retirement of the military forces of the Allies from Constantinople and the Straits began. Thus, Turkey was fully reinstated as a European power. The Greek government also ratified the Lausanne treaty and commenced to put its army on a peace basis. The number of unemployed persons in Great Britain is again increasing, which is causing much concern. The flood of crude oil and gasoline, which is severely taxing storage capacity, had its natural economic effect. Some small refiners were constrained to liqui-date in distress. The Governor of North Dakota, having acquired a supply of such cheap gasoline, insti-tuted a drastic cut in price, deliberately egging on the big refiners to do likewise. The Standard Oil Co. of Indiana accepted the challenge with enthusiasm, say-ing that it had always been its policy to sell as cheaply as any competitor. There was a humor in this situation which paved the way for the Standard to extinguish its small competitors and do by invitation of the State exactly what the muck-rakers had always charged as its greatest crime. The gasoline war spread to other states and reductions in price were made even on the seaboards. All of this was purely economic.

Jan 8, 1923

Discussion o f Papers. Meetings of the Institute offer opportunity for social acquaintance and exchange of ideas, for the--presentation of papers, and-for discussions. thereon ; also incidentally for viewing under especially favorable conditions mining operations and industrial establishments, and for hospitalities which demonstrate the brotherhood clue to kindred interests. Placing sociability prominent is not to be assumed as relegating other features of meetings to subordinate positions; but during about 40 years of membership in the Institute, the value of acquaintances formed (often ripening into close friendship), and the interchange of data, have frequently demonstrated that the social feature of meetings is of great and lasting value to the membership. Of a roll embracing 4,011 members, resident in all parts of our country, and scattered in various portions of the world, only a small fraction are able to attend meetings, even if the localities selected are alternately widely separated. Hence, the return which most members receive for their annual assessment of dues is limited to the publications issued, and the credit of being recognized as a. member of a great and worthy organization. The greater the value of the contents of our publication, the fuller the return which goes to members. While the Institute disavows responsibility for views or statements made ill papers which appear in its Transactions, the fact that these contributions, after passing proper censorship, are accepted by the Institute and spread before the world may properly be received by the writers as endorsements of their (the writers&apos;) ability to present a specific technical or industrial proposition worthy of being carefully read. But the mere presentation and publication of contributed papers falls short of fulfilling one important feature of our meetings. If the purpose is confined to having the writers&apos; views, discoveries, theories, or methods published, this can be obtained through the technical or trade journals and magazines. The true value of a paper presented at a meeting of the Institute may often be gauged by the discussion which it encourages, although there are contributions of decided value which do not especially invite discussion. However, most Of the papers offered contain statements apt to encourage criticism or elaboration by others whose experience or knowledge, or both, assist in combating or endorsing statements made.

Jan 7, 1913

By J. W. Martin, L. K. Singhal

Grain boundary M23CB precipitates have been shown to form by a process involving the migration of an austenite grain boundary, and each plate of precipitate is in parallel orientation with one of the austenite grains constituting the boundary. The carbide distribution and morphology appear to be sensitive to grain boundary mis orientation. Some areas of austenite grain bowzdary permit the development of an array of M,C, particles, some of which are in parallel orientation with one grain and some with the other grain constituting the boundary. Massive carbide at grain boundary triple points is also shown to be in parallel orientation with one constituent grain. PREFERENTIAL precipitation during aging of carbides of the type (Fe,Cr)23C6, usually written MZ3C6, in grain boundaries of quenched austenitic stainless steels has been widely recognized. M23C6 has a complex cubic crystal structure&apos; which contains ninety-two metal atoms and twenty-four carbon atoms per unit cell. Less energy is involved in forming grain boundary precipitates than in the formation of intragranular precipitates, and the process is further enhanced by the accelerated diffusion rates in the boundaries and by the probability of segregation of chromium atoms and carbon atoms to the region of the grain boundaries during prior solution heat treatment in order to reduce lattice strain. Early electron micrographic studies2, 3 involving either extraction replica or normal replica techniques established the geometric or dendritic form of the carbide particles, although this approach led to dis- pute as to whether the particles grew within the plane of the boundary or grew into the matrix.4-6 More recent thin-foil studies&apos; have claimed to identify a discontinuous precipitation process involving M23C6 at grain boundaries, and the object of the present work was to attempt to clarify the situation using modern electron micrographic and diffraction techniques. 1) EXPERIMENTAL 1.1) Material. The steel selected for this work had a base composition of 24 pct Ni-25 pct Cr-3 pct Ti and contained about 0.04 pct C. The full analysis if given in Table I. This alloy was in the form of strip which had been hot- and cold-rolled to a thickness of 0.6 mm. 1.2) Heat Treatment. Specimens 4 cm long by 1 cm wide were solution-heat-treated for 3 hr in argon at 1150°C, followed by water-quenching. Specimens were subsequently aged in vacuo at 750°C for periods up to 500 hr. 1.3) Preparation of Electron Microscope Specimens. The heat-treated strips were cut bv spark machining into discs of 3 mm diam and 0.6 mm thickness. he-discs were dished on both sides using an electrolytic jet of 15 pct HCl electrolyte at 80 v. Final electro-polishing of the discs was carried out using 10 pct perchloric acid, 20 pct glycerol, and 70 pct ethanol at 10 v. The current density was kept below 300 ma. cm"2 by cooling the electrolyte to 0" to 5°C. As soon as a small hole appeared, the electropolishing was stopped and the specimen was quickly washed with ethanol.

Jan 1, 1969

By John V. Beall

Spots Goblenski fluffed up his pork chop sideburns, checked the angle of his wide brim Stetson and ambled off the airplane. The pert Braniff hostess stood smartly at the door. "Goodbye now, take care," she said in the special airline stewardess voice superimposed on a Texas drawl. Spots smirked, "You betcha, Peaches, you too." It was a crystal clear, sunny day which New York can have at any season of the year (but rarely gets credit for) and being in high spirits Spots did not mind being captured by a cab driver. That is the cab driver brushed aside all other conversation to give a continuous colorful commentary on New York politics, revealing in the process that only the very wealthy and cab drivers share the same political views in that city. After installing himself in the fading opulence of the Hotel Roosevelt, he finished the day with a steak dinner with baked potato under sour cream and hearts of lettuce salad with Roquefort dressing at the Black Angus restaurant. The next morning he had an appointment with Hemphill, Frye and Louderdock. The offices of this prestigious firm of management consultants are high in the Pan Am Building. He was courteously received by a lacquered receptionist and was soon escorted into the presence of Mr. John Smith. "Ah, Mr. Goblenski; Spots, isn&apos;t it? Hope you had a good flight. Lovely weather we are having. Just make yourself comfortable over there, Spots." Smith seemed cordial and Spots slipped comfortably into the interview. He had always thought that management consultants were evolved from the "efficiency experts" made famous by the radio team, Amos and Andy. He associated the modern version with computers, PERT and other systems approaches. He was surprised that one of these firms was apparently acting as an employment agency. "Of course" continued Smith, "in evaluation of basic criteria of performance moduli, the human element enters, Spots, and that brings us to you." Spots sat up and focused his attention.

Jan 1, 1970

Jan 1, 1970