Search Documents

By T. M. Drown, P. W. Shimer

The precipitation of phosphoric with titanic acid, by boiling an iron solution which had been reduced to the ferrous condition by sulpharetted hydrogen or sulphurous acid, was first noticed by E. H. Bogardus in 1874.* Since that time, as far as we are aware, not much has been published on the relation of these two acids to each other, and to silicic acid, in the ordinary course of analysis of iron ores. The following investigation may perhaps aid in clewing up some of the obscure points in the analysis of titaniferous ores. THE DETERMINATION OF PHOSPHORUS. From two to five grams of the finely powdered ore are weighed into a beaker and treated with about 50 c.c. of hydrochloric acid (sp. gr. 1.12), evaporated to dryness, and heated ih an air-bath for

Jan 1, 1882

Discussion of the paper of N. V. Hansell, presented at the Cleveland Meeting, October, 1912, and published in Bulletin No. 72, December, 1912, pp. 1497 to 1,517. C. Q. PAYNE, New York (communication to the Secretary*) :-Mr. Hansell has presented in his paper a very interesting and valuable summary of the various methods of enriching iron-ores which have been developed during recent years. Particularly striking in this connection is the high degree of enrichment of the concentrates from magnetic iron-ores which is now commercially feasible. Magnetic concentrates containing from 6 7 to 139 per cent. of metallic iron, showing an efficiency of 90 and even 95 per cent. in. their separation, are not now uncommon. Such results exceed those obtained by gravity methods of treatment of all copper-, lead-, and zinc-ores, and are only equaled in the cyaniding of gold-ores and in the flotation treatment of certain copper-ores. It is of interest to note that the-type of magnetic field which is employed in securing these results, in the Gröndal (wet) and the Ball & Norton (dry) systems of treatment is the same in each case : viz., a field of alternating north and south poles. The credit for developing this simple and useful field, which has found so wide an application both in this country and abroad, is due to two American inventors and engineers, Clinton M. Ball and Sheldon Norton. At the same time, it should be noted that part of the improvement in the grade of the magnetic concentrates, especially in the case of the wet treatment of finely mineralized ores, is due to a well-devised scheme of mill-treatment, whereby a rough concentrate is usually obtained as an intermediate product, which is then recrushed and reseparated in obtaining final clean products.

Jan 3, 1913

By John Birkinbine

In the belief that a resume of what will be exhibited during this meeting, and a brief record of progress in the seven years which have elapsed since the Institute's first visit to Lake Superior would be interesting, the following statistical data have been prepared or copied from the most reliable sources, and considerations are also presented concerning the development or utilization of some of the resources of the Lake Superior Region. When the Institute, on the return trip from enjoying the charming panoramas of Thunder Cape or Isle Royale, and inspecting the unique development of Silver Islet, passed, in August, 1880, through the St. Mary's Falls ship canal, en route to Escanaba, the boat was lowered from the level of Lake Superior to that of Michigan and Huron lakes (18 feet), through two locks each 70 feet wide and 350 feet long, which had been in use since 1855. But as these locks accommodated vessels which drew 12 feet of water or less, a new lock 80 feet wide, 515 feet long and admitting vessels of 16 feet draught was approaching completion and was opened in September, 1881. The time required to pass the locks was utilized by the members in examining the work upon this new lock and in viewing the Sault Ste. Marie, which in discharging from Lake Superior all average volume of 90,783 cubic feet of water per second, forms a rapid, falling 18 feet in one mile. But the lake traffic through the St. Mary's ship-canal has developed so rapidly that another and larger lock is now required, and work has been commenced by the

Jan 1, 1888

By A. G. McGregor

In the Southwest a number of large steel chimneys discharge the gases from the copper smelting furnaces. Some of these chimneys show no deterioration after twenty years, others show serious deterioration after tour years service. A steel stack 20 ft. 7 1/2 in. (6.3 m.) in diameter by 279 ft. (85 m.) high, Fig. 1, used for roaster gases only at the Calumet & Arizona Mining CO.'s plant at Douglas, Ariz., was lined to the top of the bell, 40 ft. (12 m.) from the base, with common brick placed on end, lime and cement mortar being used. Above the bell, the stack was lined with 4 by 4 by 8 in. (10 by 10 by 20 cm.) building tile, placed on end, making a lining 4 in. thick. The tiles were supported on angle-iron rings, riveted to the inside of the chimney shell about 15 ft. apart. The chimney was put into use in the latter part of 1913. Four years later, considerable of the tile lining had fallen out of place and mixed with the flue dust at the bottom of the chimney. About a year later, several flattened and distorted sheets were noticed about 70 ft. below the top. An investigation showed that the thickness of these distorted sheets, which was originally 1/4in., had been reduced one half. One year later, or six years after the chimney went into use, several holes, a square foot and smaller in area, appeared near the flat spots mentioned. Soon afterwards, when the chimney was shut down for repairs, it was found that most of the tile lining for 125 ft, from the top had fallen out and that the steel shell was badly corroded; but where the lining remained in place the shell was undamaged. Many of the tile which had fallen out of place had become soft or flaky and crumbling, others were as hard as when placed. An analysis of the hard and soft tile is shown on p. 2. These tile were of a fireclay mixture, and were used instead of common brick on account of lower cost. The steel forming the upper 125 ft. (38 m.) was replaced, and a 4 1/4-in. (11-cm.) lining of firebrick was laid from the bell to the top of the chimney. The brick were placed on end, wedges and keys being used. After each 8-in. course was set, keyed, and wedged tight, thin mortar —water, sodium silicate, and finely ground silica—was worked into the joints. The brick are supported on angle-iron rings, every 15 ft., in the same way as the tile.

Jan 1, 1921

By E. De Goyler

Volcanic origin was among the first of the theories advanced to account for the occurrence of the salt domes of the Gulf coastal plain, northern Louisiana, and eastern Texas, and it is still being re-stated in various forms by the most recent contributors to our knowledge of the geology of such deposits. Argument has been largely by analogy and attention has repeatedly been called to the Mexican oil fields, particularly those of the Tampico-Tuxpam region, because of the occurrence of oil in close proximity to volcanic plugs in those fields, an occurrence supposed to have some resemblance to the common occurrence of oil in the salt domes of the United States. The author, having spent several months of the past year in a general study of salt domes and in a detailed study of certain domes in the United States, and having been acquainted for some time with the exploration of similar domes in the Isthmus of Tehuantepec region, Mexico, and with the general geology of the Tampico-Tuxpam region, Mexico, has reviewed the various theories of volcanic origin for salt domes which have been advanced to the present time. The purpose of this paper is to present such review and to discuss the supposed Mexican analogy. Review of Volcanic Theory R. Thomassyl who had visited the Five Islands of Louisiana between 1857 and 1859, in 1860 described them with some care, noting their distinct character, alignment, and similarity, and ascribing to them a volcanic origin. He regarded them as being akin to the mud lumps in the delta of the Mississippi and was impressed by their symmetry and by the ponds or lakes which occur on several of the islands and which he regarded

Jan 1, 1920

By Basil B. Zavoico

The World War I1 spread to Russia on June 22, 1941, when the German Armies began their invasion. The Soviet industries, which were already engaged in a tremendous armament program, further accelerated the flow of munitions, and equipment and supplies for all purposes not directly military were either entirely eliminated or reduced to an absolute minimum. With the occupation by German armies of the Dniepr and Kharkov industrial regions, this trend was necessarily further accentuated. The oil industry of Russia, in consequence, was left to rely more and more upon itself, its own very limited manufacturing facilities, extensive repair shops and probably much used equipment out of order stacked in the warehouses. All evidence available to date points to the fact that the new situation not only did not affect the production either quantitatively or qualitatively, but, on the contrary, caused a larger flow of much needed fuels to the country's war machine, primarily by renaissance of both management and labor. The oil industry of the Soviet Union, left to depend entirely upon itself for equip ment and supplies, and even for new workers and technicians to replace those called into the services, did and is still doing a good and effective job. Since it could not hope for new equipment and parts and could not blame any other industry for the delays in delivery, it dragged out old machines from storage and repaired them in its own machine shops. Often such stored and used equipment was but slightly defective, waiting for some small part from factories in Central Russia, plants that now were either in German hands or entirely converted to the manufacture of munitions. More particularly, instead of the pipe that could not be taken to the Caucasus from Central Russia, casing reclaimed from abandoned or submarginal wells was used, or pipe from the abandoned or but slightly used pipe lines; and this practice is being continued even now on a large scale, to create an ample reserve for the duration of the conflict. Indirectly such a development was even an improvement on pre-war days, when many wells about to be completed had to wait for weeks, even months, for the arrival of new pipe, all blame then being placed outside of the industry on the factories in Central Russia. For the purpose of reclaiming equipment and pipe still usable, special crews were organized. The war also caused much quicker adaptation of certain American practices and introduction of many emergency measures, such as: removal of derricks upon completion of wells and the use of drilling equipment mounted on skids for rapid transfer from location to location—both of these practices, while standard in the U.S.A., being new in Russia; installation of simplified surface pumping units; substitution of wooden bearings in the surface pump equipment; completion of wells in the Ural-Volga district, where formations are hard and tight throughout the sedimentary column, without either casing or

Jan 1, 1942

By Basil B. Zavoico

The World War I1 spread to Russia on June 22, 1941, when the German Armies began their invasion. The Soviet industries, which were already engaged in a tremendous armament program, further accelerated the flow of munitions, and equipment and supplies for all purposes not directly military were either entirely eliminated or reduced to an absolute minimum. With the occupation by German armies of the Dniepr and Kharkov industrial regions, this trend was necessarily further accentuated. The oil industry of Russia, in consequence, was left to rely more and more upon itself, its own very limited manufacturing facilities, extensive repair shops and probably much used equipment out of order stacked in the warehouses. All evidence available to date points to the fact that the new situation not only did not affect the production either quantitatively or qualitatively, but, on the contrary, caused a larger flow of much needed fuels to the country's war machine, primarily by renaissance of both management and labor. The oil industry of the Soviet Union, left to depend entirely upon itself for equip ment and supplies, and even for new workers and technicians to replace those called into the services, did and is still doing a good and effective job. Since it could not hope for new equipment and parts and could not blame any other industry for the delays in delivery, it dragged out old machines from storage and repaired them in its own machine shops. Often such stored and used equipment was but slightly defective, waiting for some small part from factories in Central Russia, plants that now were either in German hands or entirely converted to the manufacture of munitions. More particularly, instead of the pipe that could not be taken to the Caucasus from Central Russia, casing reclaimed from abandoned or submarginal wells was used, or pipe from the abandoned or but slightly used pipe lines; and this practice is being continued even now on a large scale, to create an ample reserve for the duration of the conflict. Indirectly such a development was even an improvement on pre-war days, when many wells about to be completed had to wait for weeks, even months, for the arrival of new pipe, all blame then being placed outside of the industry on the factories in Central Russia. For the purpose of reclaiming equipment and pipe still usable, special crews were organized. The war also caused much quicker adaptation of certain American practices and introduction of many emergency measures, such as: removal of derricks upon completion of wells and the use of drilling equipment mounted on skids for rapid transfer from location to location—both of these practices, while standard in the U.S.A., being new in Russia; installation of simplified surface pumping units; substitution of wooden bearings in the surface pump equipment; completion of wells in the Ural-Volga district, where formations are hard and tight throughout the sedimentary column, without either casing or

Jan 1, 1942

DAVID WHITE,* Washington, D. C.-This paper is very timely since the Philippine Islands are presumably open to the enterprise of the American driller, whereas much of the territory in that part of the world is closed to us. The United States has ambitious plans for the operation of a great merchant marine, which is to be oil burning in the main, and it takes but a glance at the world map to see the strategic advantage of oil supplies in the Philippines for such marine operations. It is a little difficult to understand why more attention has not been given to the Philippines, in spite of the difficulties attending development in these islands. A number of American oil companies are, I believe, at the present moment taking an interest in the possibilities of the Philippines. Important factors in the formulation of opinion regarding the importance of the oil deposits of the Philippines, as brought out by Mr. Pratt,1 are the point of view and the breadth of experience of the examining geologist. The average oil geologist, whose experience has been mainly in the Appalachian region, the Mid-continent, or Louisiana, or possibly even in California, on seeing the narrowness of the basins, the closeness of the folding, and the presence of igneous rocks here and there, would be likely to draw unfavorable conclusions as to the possibilities of the Philippine Islands. Geologists visiting that region should be familiar with the geological conditions of oil occurrence in Japan, Formosa, the East Indies, or in the Baku district, and their conclusions should be formulated with the knowledge and understanding of the occurrence of oil in those regions rather than in the United States.

Jan 8, 1920

The presentation of the John Fritz Medal to Professor Henry M. Hone will take place in the auditorium of the Engineering Societies? Building, 29 West 39t,h Street, New York, at 8:30 o'clock on the evening, of May 10. It is hoped that many members of the Institute will be able to attend this ceremony, and the committee desires to make special mention of the fact that ladies are cordially invited to be present.

Jan 5, 1917

By Zay Jeffries

Tungsten has the highest melting point of all the known metals, namely 3350 C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely brittle and fragile at room temperature, and when possessing a fibrous structure it may be ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given. Manufacture of Wrought and Ductile Tungsten Up to about 10 years ago, it had not been possible to work tungsten mechanically. About the year 1908, Dr. William D. Coolidge, of the General Electrie Go., produced ductile tungsten from what was then supposed to be an inherently brittle metal and which, in fact, was inherently brittle in its normal state, that is, when composed of equiaxed grains. Since that time many products, chief among which are the filaments for electric incandescent lamps, have been made from wrought and ductile tungsten. Tungsten is produced chiefly from the minerals wolframite and scheelite.1-8 The ores may be reduced in many ways. For example, the ore may be fused with alkali carbonates and the fusion dissolved in water; sodium tungstate is formed, which is soluble in water. This

Jan 1, 1919

By Leonard Waldo

The recent and rapid development of the physics of engineering materials at temperatures as low as that of liquid air and as high as that of the electric are, has drawn renewed attention to the absence of tables, properly printed and spaced, for the convenient and accurate translation of temperature from centigrade to Fahrenheit scales and vice versa. It is to be noted that the Fahrenheit scale is the almost universal usage in foundries and shops in the United States, though the laboratories of the same works employ the centigrade notation. The growing use of the electric furnace in Germany and France calls for much American citation all in centigrade high temperatures, and while the arithmetical calculation is simple, it becomes burdensome when often repeated. I have been surprised at the numerous reprints of Table I. from centigrade to Fahrenheit degrees, first privately printed for personal use, which have been made by works, blue-prints, text-books, and technical journals, and I hope that Table II., from Fahrenheit to centigrade degrees, will be equally useful. For mental calculation the easiest rule to convert centigrade into Fahrenheit is to add 32° to twice the centigrade reading less one-tenth of this product: Thus 1000' C. = 2000" — 200" + 32" = 1832" F., and to convert Fahrenheit to centigrade, subtract 32" from the Fahrenheit reading, multiply by 10 and divide by 2 and 9 successively : Thus 1000° F. = 1000° — 32° = 968° X 10 = 9680° - 2 = 4840° - 9 = 537.77° C. Another and often very convenient method is by 'use of a graphic construction as follows :

Jan 1, 1913

By Rudolf Kudlich

THE problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary, to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude, ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Later, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines-by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care.

Jan 2, 1922

By Thomas M. Drown

At the meeting of the Istitote in New York, in February, 1880," I described a process of determining sulphur iu metallic allphides, with especial reference to the determination of pyrites in coal. The procem, as then described, is as follows: A solution of sodium hydrate, of 1.25 specific gravity, is saturated with bromine. If an excess of bromiue is used it must be neutralized by the addition of a little more sodium hydrate. The pulverized mineral or coal is moistened with 25 c.e. of this solution autl heated, then hydrochloric acid is added cautiously to just acid reaction. This operation is repeated with another 25 c.c. of the alkaline solution, and again rendered acid. The mixture should be kept hot. The contents of the beaker or dish are then

Jan 1, 1881

By R. M. Raymond

RECENTLY one of the Welsh coal companies, which has an excellent plant of up-to-date ma-chinery both on the surface and underground, operated under modern methods, sent one of its engi-neers to the United States to study actual operations in the mines. He visited several of the most important and best conducted collieries, went back, and reported that the greatest difference between operations in England and in the United States was. the closer con-tact between management and workmen. By manage-ment he meant management all the way through; close cooperation between office management, superintend-ents, foremen, shift-bosses, etc., and the workmen. A visit to some of the coal mines in that country by the writer made this fact rather impressive. The feel-ing on this side of the water that the methods in use in the coal mines in England are not up-to-date was found in many cases to be quite erroneous. Many mines, particularly those with very thin beds, in which profitable operations are doubtful under the best con-ditions, have necessarily had to adhere to old methods instead of making mechanical improvements. The Powell-Duffryn mines, in the center of the South Wales district, are certainly operating successfully, and have planned their business excellently. Sufficient areas of contiguous land have been leased for extended opera-tions. Mine plants are laid out in the valley, for work-ings on both sides, on a reasonable tonnage of 1500 to 3000 tons to each operation. The beds are from 30 to 48 in. thickness, and a 3-ft. seam is considered an ex-cellent thickness of coal; in fact, the miners prefer to work on the thinner beds rather than the thick ones, where they consider it more difficult to control the backs. This company is making use of its fine coal for produc-ing electric power, which is distributed to its own operations, and for use in the communities adjoining. For this purpose methods of cleaning the fine coal are being put into use. Compressed air is generated at the central power plant and is transmitted over long dis-tances to various mines in each valley. A byproduct coke plant uses more of the fine coal and gives further returns from non-commercial coal. The long-wall system applied in sections of limited size is popular in working the small seams, and me-chanical cutting is used, also handling either by shaking chutes or belt conveyors, or a combination of both. In some mines mechanical cutting is not necessary. The backs are so handled that in the softer or somewhat crushed seams hand cutting can be carried on effec-tively.

Jan 10, 1927

By M. H. Mueller, P. A. Beck, W. P. Chernock

HARRIS introduced the term inverse pole figure for the diagrams previously used by Barrett' to represent the volume fraction p(a,ß) of material in various orientations with respect to the fiber axis in a specimen with fiber texture. The direction of the fiber axis with respect to the crystal lattice is specified by the two independent angle variables a and ß. In such a diagram p gives the fiber axis density distribution over the various crystallographic directions. The p(a,ß) may be given in a two-dimensional diagram by means of contour lines (p=con-stant) in a stereographic projection. The inverse pole figure incorporates in a single contour line diagram all the information given conventionally in pole charts for various (hkl) reflections and, therefore, it represents a considerable degree of condensation. Also, it gives this information directly in terms of the volume fraction of the specimen in various orientations, and it obviates the necessity of referring back and forth between the various pole charts in an attempt to interpret them in terms of orientations. Inverse pole figures undoubtedly represent the most adequate method for describing a texture in a quantitative manner and, at least in the case of fiber textures, this method is certainly a practicable one. Harris described1 a simple procedure for determining at least the rough outlines of a quantitative inverse pole figure. This method depends on the measurement of the intensity of X-ray reflections from various (hkl) planes lying parallel to the same specimen surface. In the case of a rod, reflections from a plane specimen surface perpendicular to the rod axis (fiber texture axis) are to be used. Harris has shown that the measured intensities I,,, reflected by crystal planes (hkl), aligned perpendicularly to the fiber axis of a specimen with unknown fiber texture, and the corresponding intensity Iu nkl from a random specimen are related to the p(a,ß) value for the unknown texture by the following equation IAkl/I°Aklw=c/c°.p(a, ß) [1] where C and C° re parameters depending on the crystal imperfections (extinction), surface preparation (e.g., thickness of oxide layer), the absorption coefficient in the specimen, effective line breadth, and instrumental factors. The values of the variables a and ß1 defining the crystal orientation, depend only on the indices hkl of the reflecting plane perpendicular to the fiber axis. Since p, as described by Harris1, is normalized in such a way that upon integration over the total orientation range its mean value is 1, the parameter C/C may be calculated approximately by the summation of Eq. l over all available X-ray reflections hkl, corresponding to a set of discrete orientations (rather than by integration over the complete range of orientations represented by the continuous variables a and ß). From the summation of Eq. 1 1/n SI AKL/I° Akl = C/C. SP(a,ß)/n is obtained where, as stated above 2p(a,ß) =1. n Therefore

Jan 1, 1959

By Fred A. Hale

Owing to the large area included in the Yellow Pine mining district, and the varied nature of its mineral deposits, a detailed geological description of the district could be covered only in an extensive monograph. This paper is intended as a description of the most prominent geologic features only with special reference to those of economic importance. The first mention of the district was in 1903 by J. E. Spurr, who briefly describes the structural geology of the Spring Mountain range. In 1906, H. F. Bain2 briefly described the Potosi mine. James J. Hillla of the United States Geological Survey, visited the district for a brief period in 1912, the result of which is an excellent reconnaissance report, covering the district in some detail but necessarily with brevity. Since that time, articles covering special features of the district have appeared in the technical press, including some by the writer, and a notable description of the Boss mine, by Adolph Knopf,4 appeared in 1915. Development of the district during the past few years has progressed so rapidly and with so many notable discoveries, particularly with reference to the rare metals, that a further description at this time may prove of interest. The writer's acquaintance with the district is based on 7 years' continuous residence in the vicinity, beginning with the spring of 1910. A. Location and Topography The Yellow Pine mining district is situated in the southwestern portion of Clark County, Nevada, about 300 miles northeast of Los Angeles, along the line of the Los Angeles & Salt Lake Railroad. The district extends from Mt. Olcott on the north to the California line on the south,

Jan 1, 1918

By J. E. Burke

Recent investigations have elucidated many of the phenomena of the grain growth process, but have also revealed some conflicting and unexplained results. Beck and his co-workers 1,2,3 have shown that grain growth continues with continued heating at one temperature until the average grain size approaches the thickness of the specimen. Plotting the logarithm of the average grain diameter, D, against the logarithm of the annealing time, t, they find the straight line relationship given by the equation: D = Ktm [,] with possible small deviations at short annealing times. K and n are constants at constant temperature. On the other hand, Wa1ker4 finds that, in alpha brass) the rate of growth falls off more rapidly than indicated by Eq i after long annealing, so that an equilibrium grain size is approached. Burke5 showed, using Walker's data, that time and temperature for grain growth are apparently related through an activation energy, H, according to the relationship: ] where h and tz are the annealing times necessary for the average grain size to increase from Do to D at temperatures T1 and T2 and R is the gas laws constant. In the case quoted, H had the value 60,000 cal per mol. The apparent validity of this relationship, at least up to 700°C, and the approximate value of H were later confirmed by Beck3 The results obtained by Beck Kremer, Demer and Holzworth2 for aluminum and aluminum-magnesium alloys could not be satisfied by such a relationship, since the slope of the isothermal curves increased with increasing temperature. These data indicate and Beck, Holzworth and HuV ater demonstrated expcrimentally that the only apparent factor controlling the rate of grain growth at constant temperature is the grain size. While many of the phenomena have been elucidated, a reasonably quantitative explanation of the process is lacking. There exists uncertainty even as to the primary driving force for grain growth, although there is a considerable body of indirect evidence that the interfacial energy of the grain boundary is responsible.7,8,io Making implicit use of this assumption, several authors14,16 have pointed out that grain boundaries should migrate toward their center of curvature. Harker and Parkerg have advanced this concept furthest, and show that one can expect grain boundary migration to occur only when the grain faces are curved, or when they meet at non-equilibrium angles. When the face is curved toward a grain A, for example, the atoms in the surface of grain B, on the other side of the boundary7 are on the average more surromded by the atoms of their lattice than the atoms on the surface of grain A. Because of thermal motion, the atoms at the interface will sometimes be attached to grain A and

Jan 1, 1949

By A. C. JR. Boyle

I. INTRODUCTION THE geological field work of the Bully Hill district, upon which this paper is based, was begun July 1, 1908, and covered a period of three months. The time was found too short for a complete report and the district was again visited in the early part of July, 1912,. from which time detailed study of the locality continued until September of the same year. This paper is the result of observations made in the mines in the immediate vicinity of Winthrop, Shasta county, Cal., during these two periods of study. The preparation of this report has been greatly facilitated by various courtesies rendered the writer by D. M. Riordan, President of the Bully Hill Copper Mining & Smelting Co., and by John B. Keating and Herbert R. Hanley, managing officers actively in charge at the mines. The elaboration and further study of the notes and collections were carried on in the laboratories of the Departments of Geology and Mining at Columbia University, and the writer takes pleasure also at this point in expressing his acknowledgments to Profs. James F. Kemp, A. W. Grabau, Charles P. Berkey, and William Campbell, for advice and assistance. In order that one may appreciate at first reading the significance of some of the details which follow, and for the sake of clearness, a brief outline of the geological relationships is here given, together with certain conclusions which have been reached regarding the genesis. of the ores and the gypsum masses. In the Bully Hill mining district an associated series of Triassic lavas and tuffs, chiefly andesites, is preceded as well as followed by sediments. The entire system is tilted so that the original bedding planes dip in general to the southeast. The surrounding region has been greatly disturbed, and in the immediate vicinity of the mines close folding of the later sediments and extreme shearing of the igneous rocks locally is a striking feature. Into the nearly vertical shear zones have been intruded post-Triassic dikes of various rock types in the following order: alaskite-porphyry and andesite-porphyry. Outside the area under consideration diorite dikes are known, but they will not receive attention further than to note that' they, probably, represent a differentiation product of the same magma from which the other two dikes came. In this connection all the dikes have an important bearing on the origin of the ores and of the gypsum found in the mines.

Jan 1, 1914

By Ulick Evans

I SHOULD like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches 'carried out in your own country-researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on, this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable .to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, .and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By John Wulff

IN a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot profilometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200° and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 415° and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on ½ sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples whose surface temperatures exceed only about 250°C. EXPERIMENTAL PROCEDURE The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, 1 by 1 cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale. On a lapping machine of the Graton2 type, both sides of each sample were polished to a flatness of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any deformations induced by surface preparation. Samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrument shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. Suc-

Jan 1, 1941