Search Documents

By J. W. Spretnak, D. A. Chatfield, G. W. Powell, J. R. Eifert

In nzost cases, the driving force for a lattice transformation is produced by supercooling below the equilibriunz transformation temperature. The interfnce reaction in isothermally annealed, multiphase diffusion couples may involve a luttice transformation which also requires a driving force. Direct experinzental evidence has been obtained for the existence of the driring force in the form of a supersaturated phase at the aocc)-0@cc) interface in Cu:Cu-12.5 ult pct A1 couples; the super saturation is equivalent to an excess free energy of approximately 3 cal per mol at 905. A tentatiue interpretation of the dynanzic situation a1 the interface based on the free energy-composition diagram is proposed. THE presently accepted theory of diffusion in multiphase couples1 states that there will be a phase layer in the diffusion zone for every region which has three degrees of freedom and which is crossed by the diffusion path in the equilibrium phase diagram. For binary systems, this restriction excludes all but single-phase fields and, for ternary systems, only one- and two-phase fields are included. In addition, Rhines"~ as well as other investigators3 6 have reported that the compositions of the various phases adjacent to the interfaces are, for all practical purposes, the compositions given by the intersections of the diffusion path with the solubility limits of the single-phase fields of the equilibrium phase diagram. Some studies of the rate of thickening of these intermediate diffusion layers indicate that the thickness of the layer changes para-bolically with time, or: where x is the position of the interface relative to an origin xo, t is the diffusion time, and k is a temperature-dependent factor. crank7 shows mathematically that, if the compositions at an interface are independent of time and the motion of the interface is controlled by the diffusion of the elements to and from the interface, then the segments of the concentration penetration curve for a semi-infinite step-function couple will be described by an equation of the form: hence, Eq. [l] follows from Eq. (21 if the interface compositions are fixed and if the motion of the interface is diffusion-controlled. Although the concept of local equilibrium being attained at interfaces has assumed a prominent role in the theory of diffusion in multiphase couples, experimental evidence and theoretical discussions which challenge the general validity of this concept have been reported in the literature. arkeen' has stated that strict obedience to the conditions set by the equilibrium phase diagram cannot be expected in any system in which diffusion is occurring because diffusion takes place only in the presence of an activity gradient. Darken also noted that it is usually assumed that equilibrium is attained locally at the interface although the system as a whole is not at equilibrium, the implication being that the transformation at the interface is rapid in comparison with the rate of supply of the elements by diffusion. ISirkaldy3 indicates agreement with Darken in that he believes the concept of local equilibrium is at best an approximation because the motion of the phase boundary requires that there be a free-energy difference and, hence, a departure from the equilibrium composition at the interface. Seebold and Birks9 have stated that diffusion couples cannot be in true equilibrium, but the results obtained are often in good agreement with the phase diagram. The initial deviation from equilibrium in a diffusion couple will be quite large because alloys of significantly different compositions are usually joined together. Kirkaldy feels that the transition time for the attainment of constant interface compositions (essentially the equilibrium values) will be small, although in some cases finite. Castleman and sieglelo observed such transition times in multiphase A1-Ni couples, but at low annealing temperatures these times were quite long. Similarly, ~asing" found departures, which persisted for more than 20 hr, at phase interfaces in Au-Ni and Fe-Mo diffusion couples. Braun and Powell's12 measurements of the solubility limits of the intermediate phases in the Au-In system as determined by microprobe analysis of diffusion couples do not agree with the limits reported by Hiscocks and Hume-Rothery13 who used equilibrated samples. Finally, Borovskii and ~archukova'~ have stated that the determination of the solubility limits of phase diagrams using high-resolution micro-analyzer measurements at the interfaces of multiphase couples is not an accurate technique because of deviations from the equilibrium compositions at a moving interface; diffusion couples may be used to map out the phase boundaries in the equilibrium diagram, but the final determination of the solubility iimits should be made with equilibrated samples. The purpose of this work was to investigate the conditions prevailing at an interface in a multiphase diffusion couple and to compare the interface compositions with those associated with true thermodynamic equilibrium between the two phases. Microanalyzer techniques were used to measure interface compositions in two-phase Cu-A1 diffusion couples annealed at 80@, 905", and 1000°C for various times.

Jan 1, 1969

By W. J. Heck

The need for a better understanding of the effect of fluid pressure on the strength of intact and jointed rock has long been recognized. The behavior of pore fluid pressure was first pointed out by Terzaghi 1 who suggested the application of the effective stress concept to rock and concrete. While the effective stress concept has been used for some time in the design of mass concrete dams, it only recently has been applied to rock. Robinson 2 and Handin et al.3 evaluated the effects of pore pressure on a variety of sedimentary rocks and demonstrated the validity of the concept. Work using pore fluids other than water has been done by Boozer, et al.4 who considered strain rate and temperature as additional variables. According to the effective stress theory, the effective stress, [a], is the difference between the total stress, [a], and the pore pressure, u, and is the controlling factor influencing frictional strength of rock, other parameters remaining constant. Assuming the Mohr-Coulomb failure criteria applies, the shear strength, T, is given by the equation [r=d+ (a-u)tan ¢](1) where [~F], the angle of internal friction, and c, the cohesion intercept of "no load" shear strength, are the effective stress parameters.* Robinson,2 Handin,3 and others have demonstrated that moderately porous sand-

Jan 1, 1972

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth's surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer's airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist's artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth's surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer's airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist's artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

By R. J. Wasilewski

Electrical resistivity variation with temperature was measured on a series of alloys containting up to 33 at. pct of oxygen over the range 77° to1500°K. The resistivity behavior is highly anomalous and itzconsistent with simple metallic conduction. Both composition and temperature-depended resistivity singularities were observed. A few experiments carried out on Ti-N and Zr-O alloys indicate the presence of similar anomalies. These observations, together with the published data on effects of substi-tutional alloying on the resistiuity of titanium, suggest that the anomalies are inhevent in the electron structure of this group oj metals. The existence of two-band conduction, and a significant shift of bands relative to each other with temperature and/or the electron concentration are suggested. CONSIDERABLE advances have been made in recent years in the alloy theory of simple metals. Very little, however, is known about the bonding in transition metals and their alloys.&apos; Titanium, with its relatively few electrons, may be expected to show simpler alloying behavior than the more complex transition elements. Its alloys with the interstitial elements appear particularly attractive in an investigation of bonding characteristics because of a) the simple nature of the solute elements, b) the remarkable similarity between the equiatomic structures Tic, TiN, and TiO, and c) the extensive solid solubility ranges of oxygen and nitrogen in a titanium reported.2,3 The Ti-O system was chosen for the most extensive investigation because of the relative ease of preparation of suitable specimens. Since the main object of the work was to obtain data on the bonding and its changes on alloying, electron-sensitive properties were primarily investigated. The present work describes the investigation on the electrical resistivity-temperature-oxygen content relationships. A few experiments were also carried out at selected compositions in the Ti-N and Zr-O systems. EXPERIMENTAL Materials and Method. Polycrystalline specimens were prepared in the form of hairpin strips some 50 by 5 by 0.15 to 0.50 mm by direct metal-gas reaction. This was carried out by controlled oxidation followed by a homogenizing anneal at a higher temperature. All the test specimens were fully homogenized as judged from the uniform microstructure and microhardness. To avoid preferred orientation, each strip specimen was annealed in the ß range prior to the oxidation, this procedure assuring random orientation in the strip;4 hence any texture resulting from the oxidation reaction itself affected all the specimens to a similar extent. Titanium used was of high purity (66 DPN, 10 Kg load; major impurities 0,-43G ppm, N,-70 ppm, C-25 ppm, Fe-14G ppm). The solute content of the alloys was determined by weighing, after the reaction with a known amount of oxygen. The specimens in which the discrepancy between the volumetric and gravimetric measurements exceeded 2 pct (or 0.2 mg for the low oxygen alloys) were rejected. The mean between the two measurements was then taken as the oxygen content of the alloy. Check analyses showed no measurable nitrogen contamination. All oxygen contents are given in atomic percent. Zr-O alloys were prepared in identical manner from hafnium-free crystal bar metal, cold-rolled to strip 0.25 mm thick. Ti-N alloys required very long reaction times at the maximum temperature available (1250°C). In order, therefore, to detect possible oxygen contamination, duplicate specimens were reacted in every experimental run, and one of these was analyzed both for oxygen (vacuum fusion) and for nitrogen (Kjeldahl). Only the specimens in which the check analysis showed < 1000 ppm O were then used for resistivity investigation. Since only relatively high nitrogen alloys (7.1 at. pct; i.e., 2 wt pct N,) were investigated, this oxygen contamination was considered permissible. Dc resistance was measured by the four-probe method as previously described.= The temperature was determined with a calibrated thermocouple placed in the center of the specimen hairpin. The errors in the specimen resistance values thus obtained were estimated at 1 pct due almost exclusively to the finite thickness of the potential wires and the consequent uncertainty as regards the true resistance length of the specimen. For the calculation of the specific resistance, however, no dimensional measurements could be carried out on most of the

Jan 1, 1962

By R. R. Vandervoort, W. L. Barmore

Tensile creep experiments were conducted on high-purity, poly cvystalline rhenium from 1500" to 2300°C at stresses from 1500 to I0,OOO psi in a vacuum of 10-a torr. The apparent activation energy for creep was 60 kcal per mole, and the steady-state creep rate varied directly with stress to the 3.4 power. Dislocation substructure that developed during creep was studied by transmission electron microscopy. Possible rate-controlling deformation mechanisms are discussed. The creep behavior of most metals at elevated temperature can be represented by the following equation:&apos;&apos;&apos; t = Cf(s)(^)(s/E)nD [1] where i = steady-state creep rate, C = constant, f(s) = a function involving microstructure, s = applied stress, E = the average elastic modulus at test temperature, n = constant, D = diffusion coefficient According to this well-established relationship, metals with higher elastic moduli and lower diffusion coefficients should have greater creep resistance at the same stress and temperature and equivalent mi-crostructures. While no diffusion data are available, the diffusivity of rhenium should be less than that for most other refractory metals because of its high melting point and hcp crystal structure. The Sherby-Simnad relation for calculating atomic mobility in metallic systems3 predicts that the diffusion coefficient for rhenium is less than that experimentally determined for tungsten4 in the temperature region 1500. to 2200°C. At these temperatures the elastic modulus for tungsten5 is only slightly larger than the extrapolated modulus for rhenium.6 Thus, rhenium is a good possibility for a a high-temperature structural material, but few data on the creep of rhenium have been reported. This investigation was undertaken to study the high-tempera-ture deformation behavior of rhenium in detail. EXPERIMENTAL TECHNIQUES The material used in this study was consolidated from high-purity powder. After cold pressing the powder to a plate a in. thick, the billet was sintered in hydrogen at 2250°C for 24 hr. The plate was reduced to 0.100 in. by cold cross rolling with intermediate anneals at 1650°C for 20 min between passes. The plate was further reduced to 0.060 in. by unidirectional cold rolling with similar heat treatments between passes, and then finally stress-relieved in hydrogen at 1650°C for 30 min. Specimens tested at 1900°C and below were pretest-annealed at 1900°C for 2 50 hr. Specimens tested above 1900°C were pretest-annealed at 2400°C for 5 hr. The impurity content in the "as-received" plate was quite low, table I. Essentially no change in impurity levels was detected in specimens after creep testing. All creep tests and annealing treatments were conducted in a vacuum of 10-8 torr in a test furnace heated by a tungsten mesh element. The load was applied to the specimens through a bellows, and stresses were maintained to ±1 pct of the selected value by periodic corrections for changes in specimen cross-sectional area during creep and for changes in the bellows spring force due to load column extension. One-inch-diameter tungsten force rods were used in the hot zone of the furnace. Deformation at temperature was measured by optically tracking gage marks on the specimen. Temperature was measured by a calibrated optical pyrometer and was determined to ±5"C. Grain sizes were determined by the linear intercept method and specimens were examined in the "as-polished" condition, using polarized light. Specimens annealed at 1900°C had a grain size of 52 ± 5µ , and those annealed at 2400°C had a grain size of 148 * 11 µ. Pieces were cut from the gage section of creep-tested specimens and planed to a thickness of about 0.010 in. by spark discharge machining. Thin foils for viewing by transmission electron microscopy were obtained by electropolishing in a solution of 6:3:1 ethyl alcohol, perchloric acid, and butoxy ethanol, respectively, using the window technique. Bath temperature was —4OoC, and the cell potential was 35 v. The foils were examined in Siemens Elmiskop I, operating at 100 kv. RESULTS AND DISCUSSION In order to analyze the results from creep experiments, Eq. [I] is rewritten in the following form: <=Kf(s)ne-/RT [2] where K = constant, ?// = apparent activation energy for creep,

Jan 1, 1970

By W. A. Clark, E. H. Dresser

ORE from the Minnesota iron ranges is transported from the mines to the loading docks on Lake Superior over four different railways: the Great Northern, Northern Pacific, Soo Line, and Duluth, Missabe and Iron Range, with hauls varying from 60 to 110 miles. For this service a large amount of specialized equipment is used. The steel ore cars are of the hopper type, 24 ft. long, to dump into alternate pockets of the docks, these pockets being 12 ft. long to correspond with the 12 or 24-ft. spacing of the boat hatches. The more recently con-

Jan 1, 1941

By C. W. Allen, B. D. Cullity, H. S. Choi

The torsional deformation of aluminum and magnesium crystals is investigated, with particular reference to the dependence of proportional limit on crystal orientation. The proportional limit is found to be governed by the average value of the resolved shear stress on the most highly stressed slip systems, but the proportional limit does not strictly obey a critical-resolved-shear-stress law. The behavior of a cylindrical single crystal stressed in tension is well known: plastic flow begins when the resolved shear stress on the most highly stressed slip system reaches a critical value. There is much less understanding of the effect of torsion on such a crystal and on the way in which the critical-resolved-shear-stress law should be applied to torsional deformation. In the present paper particular attention is paid to the dependence of plastic yielding on crystal orientation and lesser attention to the mechanism of flow after yielding has occurred. New work on aluminum and magnesium crystals is presented, and previous results obtained in this laboratory on magnesium1 are re-examined. STRESS DISTRIBUTION The problems involved in torsional deformation of single crystals are due entirely to the complexity of the stress distribution. In tension, if loading conditions are perfect, the shear stress on any particular slip plane is completely uniform over the entire area of that plane. In torsion, on the other hand, the stress on any selected plane in a particular direction varies not only from center to edge of the specimen but also around its perimeter. It is convenient to express the stress at any point in terms of t0, which is the shear stress acting at the surface of a cylindrical specimen on a plane normal to the axis and in a direction tangential to the cylinder. At point P of Fig. 1 this stress acts in the direction of axis 2 and is given by To = 2T/pr3 [1] where T is the applied torque and r the specimen radius. This stress can be resolved on any chosen slip system, and details are given in the Appendix. Let P be the point on the specimen surface where the stress is to be evaluated; P is defined by its angular distance A from an arbitrary reference line through 0 normal to the axis. his line is usually taken as the direction of incidence of the X-ray beam used to determine the crystal orientation.) Then the shear stress t, acting at P in direction Dona plane whose normal is N is given by Ts/TO = sin ? 0, cos ?d sin (?0, - ?) + cos ?, sin ?d sin (?d - ?) [2] where 0, and Od are the angles between N and D, respectively, and the axis, ?0 and ?d are the angles between the projections of N and D, respectively, on the transverse plane and the reference line through 0. By means of Eq. [2], the stress 7, acting in any given slip direction can be computed. In the previous work on magnesium1 only gross slip tangential to the specimen surface was considered, and this

Jan 1, 1963

GENERAL GEOLOGICAL DESCRIPTION The uranium mineral appraisal herein described was made for an ore deposit in New Mexico. The uranium mineralization occurs as roughly tabular to lens-shaped deposits of varying thickness within the sandstone of the Jackpile formation of Jurassic age. The mineralization occurs at several horizons within the Jackpile formation, but is not always confined to specific beds. It often transgresses across stratigraphic layers, as demonstrated when attempting correlation of uranium gamma anomalies between adjacent drill holes. Preferred mineral trends have been established in some parts of the deposit, but are not always predictable when attempting to extrapolate beyond the zones defined by drill hole sampling. MANAGEMENT OF DRILL HOLE SAMPLE DATA All of the drill hole sample data used in the appraisal were obtained from interpretation of gamma-ray logs. A brief description of gamma-ray log sampling is given in Chapter 2. Two preliminary steps are involved in preparing gamma-ray logs into sample data normally acceptable for computer manipulation. 1) The gamma analog trace produced by the downhole probe must be digitized, i.e., counts-per-second (CPS) are recorded for each 0.15 m (1/2-ft) interval across the gamma-ray anomaly. The work is usually done on a "digitizer" while following the analog trace with an electronic stylus on a special tablet or table. The other alternative is to do the work manually. Some of the newest downhole logging equipment produces a magnetic tape output which can be read by a computer. 2) The gamma-ray CPS values must then be converted to equivalent U308 assay values, taking into consideration all appropriate correction factors. The US Atomic Energy Commission, now part of the Department of Energy, developed the theory and algorithm for this conversion in the 1960&apos;s, and though the work can be done manually, it is best done with the GAMRED (gamma-reduction) computer program. Fig. 14-1 illustrates a typical analog trace produced by the probe instrumentation, including gamma-ray trace (left), self-potential electric log (center), and resistivity log (right). Fig. 14-2 shows a form of the computer output after the analog data has been digitized to 0.15-m (1h-ft) intervals and converted to percentage U308 values for the same hole. The U308 grade bar graph on the right permits rapid visual inspection of anomalous values by depth and elevation. The converted U308 sample data were next processed by the SURVEY program that assigned to each assay interval [0. 15-m (1h-ft)] an X Y Z coordinate, taking into account all deviations indicated from downhole survey information. The output file of the SURVEY program was listed on the line printer for examination by project geologists, and also became the main input file for the URAN/ COMP compositing program, which is designed to group individual 0.15-m (/-ft) U308 sample values into larger intervals representing discrete anomalous zones according to a series of specified parameters entered into the program by the user. Composite U308 intervals were computed by the URAN/COMP computer program, the logic of which may be briefly described as follows: Step 1 The program searches for the highest U308 value in the hole and builds a composite by adding the highest grade interval on either side so long as the added value is greater than a minimum acceptable grade, and the total composite, after addition, meets minimum GT (grade times thickness) constraints. Step 2 The program loops back to find the next highest assay value in the hole not already included into a composite, until all anomalies above minimum cutoff grade are composited. Step 3 Individual composites are combined if they are closer than a specified minimum waste thickness, and the resultant composite grade still meets GT minimums.

Jan 1, 1980

By Staff

Concentrates at the rate of 1000 tons a day are being smelted by International Nickel Co.&apos;s new commercial flash smelting furnace. Developed by Inco, the process is a radical departure from the former practice which involved conventional smelting in coal-fired reverberatory furnaces. In the new process copper flotation concentrate and flux are injected horizontally with oxygen into a specially designed reverberatory furnace, and smelting temperature is maintained solely by the flash combustion of iron and sulphur while the particles are in suspension. The major benefits of this new process stem from two sources: 1)-Substitution of energy from local resources for imported coal; and 2)-Production of liquid sulphur dioxide, replacing equivalent imported sulphur. A measure of these benefits is afforded by considering the saving, in 1954, of 60,000 tons of coal and the production of 70,000 tons of liquid sulphur dioxide, equivalent to 35,000 tons of sulphur.

Jun 1, 1955

Jan 1, 1967

US 4,141,854-Method of resolving water-in-oil emulsions from the organic solvent extraction of uranium from an aqueous ore leach solution The emulsion is treated at optimum temperature with a water-soluble acrylamide copolymer which contains 5-50% by weight of a lower alkyl substituted tertiary aminoethyl methacrylate or quaternary ammonium salts thereof The emulsion is broken, enabling recovery and reuse of the organic portion of the emulsion A M Pavilcius and M A Latko, assigned to Nalco Chemical Co Feb. 27, 1979 3 pp (252-301 1W) Filed: 12-14-77 (860,542). US 4,142,952-In the recovery of copper from an ore leach solution, the solution is contacted with a water-immiscible organic solvent containing 5 to 20 g/L of o-hydroxyaryloxime and 2 to 20 times the weight of the o-hydroxyaryloxime of nonylphenol The loaded solvent phase is separated from the aqueous phase and stripped with sulfuric acid Copper is recovered rapidly and in high yield from aqueous solutions containing high copper concentrations R F Dalton, as¬signed to Imperial Chemical Industries Ltd Mar 6, 1979 6 pp (204-106) Filed 1-3-77 (756,067). Priority: United King¬dom, 1-30-76 (3788/76), 6-15-76 (24722/76), and 10-21-76 (43711/76). Same- British 1,549,615, dated Aug. 1, 1979 US 4,148,631-In the recovery of nickel and cobalt from a mixed sulfate ore leach solution, both metals are extracted by means of a cationic extractant, the loaded extractant treated with an aqueous chloride or thiocyanate solution to back extract the cobalt, and the cobalt then recovered by solvent extraction or ion exchange with an anionic extractant Recovery is effected in a relatively few extraction steps. F Babjak, V A Ettel, and K. R Dymock, assigned to Interna¬tional Nickel Co , Inc, Apr. 10, 1979 6 pp (75-101 BE) Filed¬7-27-78 (928,401). Priority- Canada, 12-28-77 (293,967) US 4,148,813-An improved extractant for use in the recov¬ery of nickel and cobalt from an ore leach solution comprises a water immiscible organic solvent system containing solubilized mercaptide ions, e g , dodecanethiol. Cobalt and nickel mercaptides solvated in the organic phase are easily stripped in the presence of carbon monoxide and an aqueous alkaline solution A. S. Rappas and J. P. Pemsler, assigned to Ken¬necott Copp

Jan 1, 1980

By W. R. Phibbs

The blast furnace of the Columbia Steel Corpn., at Ironton, Utah, was put in blast April 30, 1024, and its operation has presented some interesting problems. The coke for the furnace is furnished by 33 Koppers Becker type ovens of 15 tons capacity each. The coal is shipped from the company&apos;s mine at Columbia, Utah, which is approximately 123 miles from Ironton, and is probably the highest volatile coal that is being coked for blast furnace use in this country. The analysis of the coal is: PeR Cent. Moisture................................................. 3.90 Volatile.................................................. 39.00 Fixed carbon............................................ 51.10 Ash............................................... 6.00 Sulfur................................................. 1.07 The analysis of the coke is: PeR Cent. Volatile.................................................. 0.55 Fixed carbon............................................. 89.70 Ash...................................................... 9.75 Sulfur................................................... 1.05 The coke is light and of a fingery construction, but is very fast burning. A screen test of the coke as loaded into the skip tubs at the furnace shows the following: Per Cent. On 2 in.................................................. 17.90 On 11/2 in................................................ 41.78 On 1 in.................................................. 27.80 Through 1 in............................................. 12.52 The by-product yields are as follows: Gas................................. 11,000 cu. ft. per ton of coal Sulfate............................... 30 Ib. per ton of coal Tar.................................. 12.65 gal. per ton of coal Motor fuel........................... 3.00 gal. per ton of coal Average B. t. u. in gas................. 567

By L. O. Storey

The McDermitt mine was found as a separate mercury ore-bearing occurrence approximately 305 m (1000 ft) northeasterly and in a different geologic setting from the old Cordero mine, which had been the district&apos;s major producer. The following briefly describes the discovery of the new deposit and the Placer Amex lnc. involvement. The Cordero mining property was under lease by Sierra Mineral Management from the owner Fred H. Lenway in February 1971, when the property was brought to the attention of Placer Amex Inc. (known at that time as American Exploration and Mining Co.) by Richard F. Hewlett of Sierra Mineral Management. The property was first examined by Amex geologists in the spring of 1971, who reported favorably on the project. During that year, Sierra Minerals Management had retained Dr. Larry Walters as a consultant. He proceeded to drill test mercury soils anomalies which he had found northeast of the old Cordero mine in an area overlain by recent alluvium and gravel. An area known as the D area was subsequently blocked out and ascribed a tonnage of about 18 1 kt (200,000 st) which occurs in the vicinity of the eastern edge of the currently defined McDermitt ore body. This mineralization was found in flat lying mercury-bearing lakebeds, unlike the steep structurally controlled ore which was mined in the old Cordero mine. It became apparent to Placer Amex that since the chances of much more extensive ore were good in such a geologic environment, additional exploration was warranted. A joint venture was formed in October 1972 by American Exploration and Mining Co. and Sierra Mineral Management to further explore the Cordero property. The project exploration was fully funded and managed by Amex. Sampling began by Placer Amex in the D area where an open trench had exposed the lakebed ore. Visible cinnabar could not account for the high-grade mercury assays taken from the trench, and an unknown mercury mineral was suspected. Subsequent work established the presence of a chlorine-bearing mercury sulfide which may have enriched the lakebeds as a secondary supergene mineral. Early identification of the mercury-bearing mineral corderoite (Hg3Cl2S,) aided in the geologic concepts for the ore occurrence and was helpful in exploring for the expansion of the D area. Corderoite was found occurring with cinnabar in the lakebeds, and in places it is a major contributor. Specimens of the unique ore were given to Dr. Eugene E. Foord and Dr. Pieter Berendsen at Stanford University, who subsequently identified the chemical and crystallographic makeup of the new mineral and described it for the first time as a naturally occurring substance. Metallurgical work on mercury recovery from the newly described mineral was carried out by the Placer Development Ltd. laboratories in Vancouver, and an acceptable recovery system was worked out together with a planned mill design. Step out drilling from the D area by Placer Amex Inc. encountered extensive flat lying lakebed ore. The McDermitt ore body, as subsequently defined by drilling, was found to contain 2.7 Mt (3 million st) of open pittable ore, containing approximately 5 kg/t (10 lb per st) Hg. The ore body gently dips to the north and is found lying mainly in claybeds just above an opalite breccia blanket which overlies the earlier volcanics. Some ore is also found in the opalite breccia. The mine and mill were constructed under an operating joint venture with Placer Amex Inc. and Sterling Mineral Ventures, and production began in June 1975 at the rate of 20,000 flasks per year. The mine is currently in progress.

Jan 1, 1985

By E. H. Crabtree, V. W. Winters, T. G. Chapman

IN 1939 one of the authors* described advances in carbon-cyanidation for the period 1932 to 1939 • T. G. Chapman: A Cyanide Process Based on the Simultaneous Dissolution and Adsorption of Gold. Trans. AIME (1939) 134, 207. and included: (1) the dissolution of gold in an ore pulp by cyanide and its simultaneous adsorption by carbon, (2) the stage addition of adsorptive carbon and its movement countercurrent to the flow of the ore pulp, and (3) the recycling of adsorptive carbon. Considerable additional experimental and pilot plant work have been done by the authors since 1939 and the results of such work E. H. CRABTREE, JR., Member AIME, is Director of Milling, Eagle-Picher Mining and Smelting Co., Miami, Okla., V. W. WINTERS is Superintendent, Sahuarita Concentrator, Eagle-Picher Mining and Smelting Co., Tucson, Ariz., and T. G. CHAPMAN, Member AIME, is Dean, College of Mines, University of Arizona, Tucson. AIME Sun Francisco Meeting, February 1949. TP 2744 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received March 3, 1949. have been sufficiently encouraging to justify a second paper. Developments from 1939 to 1948: In 1941, Verne W. Winters did the first experimental work in eliminating agitation during dissolution and adsorption and thereby demonstrated that the dissolution of gold by cyanide and its simultaneous adsorption by carbon take place essentially to completion in a stagnant pulp. Shortly thereafter, and as a result of the stagnant pulp experimental work, Winters and Chapman demonstrated that soluble gold, in a cyanide ore pulp, would migrate from the ore pulp through a perforated container and be adsorbed by carbon within the container. During the same year, the Eagle-Picher Mining and Smelting Co. erected a 25-ton capacity pilot plant at the Harquahala mine about 9 miles from Salome, Ariz. Experimental work at this plant comprised chiefly the stagnant pulp modification of carbon-cyanidation although considerable work was done in the grinding and activation of carbon, and testing various methods of extracting adsorbed gold from carbon. Soon after the completion of the Harquahala

Jan 1, 1951

By E. H. Crabtree, T. G. Chapman, V. W. Winters

IN 1939 one of the authors* described advances in carbon-cyanidation for the period 1932 to 1939 • T. G. Chapman: A Cyanide Process Based on the Simultaneous Dissolution and Adsorption of Gold. Trans. AIME (1939) 134, 207. and included: (1) the dissolution of gold in an ore pulp by cyanide and its simultaneous adsorption by carbon, (2) the stage addition of adsorptive carbon and its movement countercurrent to the flow of the ore pulp, and (3) the recycling of adsorptive carbon. Considerable additional experimental and pilot plant work have been done by the authors since 1939 and the results of such work E. H. CRABTREE, JR., Member AIME, is Director of Milling, Eagle-Picher Mining and Smelting Co., Miami, Okla., V. W. WINTERS is Superintendent, Sahuarita Concentrator, Eagle-Picher Mining and Smelting Co., Tucson, Ariz., and T. G. CHAPMAN, Member AIME, is Dean, College of Mines, University of Arizona, Tucson. AIME Sun Francisco Meeting, February 1949. TP 2744 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received March 3, 1949. have been sufficiently encouraging to justify a second paper. Developments from 1939 to 1948: In 1941, Verne W. Winters did the first experimental work in eliminating agitation during dissolution and adsorption and thereby demonstrated that the dissolution of gold by cyanide and its simultaneous adsorption by carbon take place essentially to completion in a stagnant pulp. Shortly thereafter, and as a result of the stagnant pulp experimental work, Winters and Chapman demonstrated that soluble gold, in a cyanide ore pulp, would migrate from the ore pulp through a perforated container and be adsorbed by carbon within the container. During the same year, the Eagle-Picher Mining and Smelting Co. erected a 25-ton capacity pilot plant at the Harquahala mine about 9 miles from Salome, Ariz. Experimental work at this plant comprised chiefly the stagnant pulp modification of carbon-cyanidation although considerable work was done in the grinding and activation of carbon, and testing various methods of extracting adsorbed gold from carbon. Soon after the completion of the Harquahala

Jan 1, 1951

By P More

US 4,132,621-In the electrowinning of aluminum, the cells are aligned in a lengthwise direction so as to lessen the harmful influence of the induced magnetic fields Each cell is supplied with current from the preceding cell both via the head arid at least one side riser The output of the cathode bars is divided into two separate groups, the upstream group supplying the head of the subsequent cell arid the downstream group supplying the side risers of the subsequent cell This produces a substantial improvement in cell efficiency arid a greater regularity P Morel, J P Dugois, arid B Langon, assigned to Aluminium Pechiney. Jan 2, 1979 12 pp. (204¬243M) Filed 1-12-78 (868,861) Priority: France, 1-19-77 (77/2,213) US 4,134,806-Cells, anodes, arid methods for use in the electrowinning of nickel, cobalt, copper, zinc, or other metals from an acid ore leach solution or the like The cell is provided with vertically immersed stationary cathodes and stationary rod anodes which are noncorrodible by the electrolyte arid are electrocatalytic to the anode reaction. The spaced parallel anode rods are connected to electric current supply bars The anode rods have an electroconductive core made of a metal alloy arid a surface coating of an oxide of platinum or a platinum group metal The ratio of active cathode surface area to active anode surface area is preferably at least 3 0. De Nora arid C Traini, assigned to Diamond Shamrock Tech¬nologies, SA Jan 16, 1979 13 pp. (204-105R) Filed 9-15-77 (833,661) Priority Italy, 1-29-73 (19738 A/73). Same British 1,434,334-5, dated May 5, 1976 US 4,135,994-In the electrowinning of aluminum at a high current efficiency, the electrolytic bath is a mixed molten salt consisting of 2-15% by weight of aluminum trichloride, 15-83% of sodium chloride, 15-70% of combined calcium chloride arid magnesium chloride but riot more than 40% of calcium chloride, arid optionally up to 10% of barium chloride Preferably, plate-shaped graphite electrodes used for both cathodes and anodes are arranged in parallel inclined relation so that the axis in the lengthwise direction makes an angle of from 10° to 45° to the horizontal. T Ishikawa arid H Ichikawa, assigned to Nippon Light Metal Co Ltd Jan 23, 1979 4 pp (204-67) Filed 11-15-77(851,632) Same British 1,550,502, dated Aug 15, 1979

Jan 1, 1980

By James Elton

THIS paper covers, besides laboratory work, a study of actual operation at the Washoe Smelter over a considerable period of time, together with the results of a visit to the Midvale plant of the United States Smelting- & Refining Co., near Salt Lake. For the latter privilege, as well as permission to publish the resulting data herein given, I am indebted to George W. Heintz, General Manager of the Midvale plant, and here take pleasure in. expressing my appreciation for the many courtesies extended to me by Mr. Heintz and members of the technical staff at the smelter. Almost all of the world&apos;s supply of arsenic is recovered as a by-product in the smelting of other metals. It is seen on the market in various forms, the most common being arsenic trioxide, the ? white arsenic " of commerce, which is sold as a heavy white powder, or in white, glassy, translucent masses. The trioxide is used in the manufacture of pigment, glass, and insecticides. About 50 per cent. of the domestic consumption is supplied by imports.

Jan 8, 1913

THE following employment items are made available to AWE a non-profit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address. all mail to the proper key numbers in care of the New York Office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of, positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Executive Engineer, Mining Engineer Graduate, 25 years&apos; management experience from plant operation to vice president in charge of manufacturing for national concern. Management and operational experience in gypsum, asbestos, cement, paper, felt, asphalt products. West Coast or South location preferred. Prefer permanent position but would consider connection on consulting basis. M-663. Geologist and Engineer, E.M. (Geol.), Ph.D., 46, married, excellent health. Nineteen years&apos; broad experience including appraisal, acquisition, large-scale exploration, special problems, planning, organization, and supervision in U.S., Africa, and South America. Sound approach and execution, writes clearly. Currently employed but available short notice. M-660. Mining Plant Designer. Over thirty years&apos; broad mining experience. Graduate mining engineer, registered mechanical engineer, experienced structural engineer. Member AIME, NSPE. Fully experienced all phases design, from initial plant layout to final details. Excellent references. Presently employed but available reasonable notice. M-661-238-Chicago.

Jan 1, 1952