Search Documents

By T. A. Rickard

Freeman, the English historian, said that he had learned from Macaulay "never to be afraid of using the same word or name over and over again if by that means anything could be added to clearness or force. Macaulay never goes on, like some writers, talking about `the former' and `the latter', `he', `she', `it', and `they', through !clause after clause, while his reader has to look back to see which of several persons it is that is so darkly referred to". He might have learned also from Macaulay that a preposition makes a' feeble ending for a serious statement. How often do you hear `the former' and `the latter' in conversation? Good conversation is a guide not to be dis¬dained. When you must use `the latter', do not confuse it with `the last'. Cheap labor, cheap fuel, and cheap transport are essential, the latter [last] being particularly important in base-metal mining. The apparatus may be used to determine such gases as hydrogen sulphide, chlorine, oxides of nitrogen and some others, as well as sulphur dioxide. In the case of the latter two, etc. The two last mentioned are "sulphur dioxide" and "some others". He should have stated which two, and he should have avoided that wretched phrase "in the case of ". Pinning may be partly prevented by use of chalk, oil, or turpentine. The latter [last] is best. I "Partly prevented" is a poor phrase. `Prevented! is a word that does not lend itself readily to modification. He means `checked' or `corrected'.

Jan 1, 1931

By Stanley C. Herold

TWENTY-FIVE years ago no distinction was made between water wells and oil wells except in the nature of the fluid produced. Water wells usually showed no decline in their rate of production; when oil wells showed decline something in the manner of handling them was considered wrong. Both water and oil were believed to be subject to the same physical laws in their underground movement toward the wells. Today a sharp distinction is made between them. Whereas water exists alone in the porous formations at depth, oil is usually accompanied by gas. This mixture does not behave as a liquid alone. It is a frothy, seething mass of foam which approaches and enters the wells. Different physical laws come into play. Twenty-five years ago attention was directed entirely to the well itself; today the well is accepted as a mere hole in the ground, a hole to be equipped properly for efficient service, yet without any value whatever unless it is backed up by a sufficiently prolific reservoir. Then, we were concerned with wells alone, 3000 ft. in depth; now commercial wells and their reservoirs are 10.000 ft. deep. Petroleum engineering concepts have necessarily therefore undergone a change in this last quarter century. What are they today?

Jan 1, 1937

Edward A. UehlinG, New York City (communication to the Secretary*):—Mr. Baker's paper is one that brings up a subject of great importance, and if full statistics could be collectecl of the number of furnace-linings ruined by reason of bad distribution by skip-hoists, it would be found an astonishing array. Unfortunately a universal remedy has not yet been found. The fact that Mr. Baker has apparently succeeded in overcoming the trouble at Sydney, is no guarantee that the same remedy applied at another plant, where very different or even slightly different conditions prevail, mould cure the trouble. That it requires but a slight continuous difference of penetrability in the column of the descending stock of one section, over another, to produce channeling, is clearly demonstrated by Mr. Baker's experiments, by which he reversed the channeling from front to rear instead of remedying the trouble. Every change in the physical make-up of the charge necessarily requires a specific adjustment; even supposing this feasible, the regular working of the furnace is by no means assured, because with the high pressures now customary, the tendency of the ascending gases to plow their way through in a direct course, prevails, and having once opened up a passage, they will persist and cause trouble. Homogeneous filling-, hard driving and regularity of working are incompatible. The higher the furnace, the greater the

Jan 1, 1905

By Henry Wurtz

HERACLITUS, a sage of antiquity, called the dark philosopher, who refused a throne, preferring a hermit's cell, propounded, twenty-four centuries since, the maxim : [ ] War (or strife) engenders all things. This, though probably intended by Heraclitus to apply especially to the internal forces of nature, is often said, with equal reason, of the affairs of men. Controversial strife, whether fortunately or unfortunately, is a crucible through which all new discoveries in science, and all technical applications of science must pass-a test which they must all endure before they can become so vitalized as to germinate, so to speak, take root in the human mind, grow tip, and overspread the earth. The greater the number and the power of the elements arrayed against such a growth, and of the influences hostile thereto, the greater should be the inherent vitality of the germ, the more strenuous, skilful, and persistent its cultivators and upholders. During the decade last past we have had, in spite of the severe stringency of the times, an active growth of this kind in progress, whose prospective importance it would now be difficult to overrate. This is the movement which has for its motive the idea that, generally speaking, fuel should be gaseous in form, and which has for its goal the introduction into general public use of gaseous products, made by cheap and rapid processes and on a gigantic scale, distributed throughout our cities and towns in distribution-systems which shall be proportionately gigantic, and sold at prices which will bring such fuel within the means of the poorest householders. Personally, for ten years past, the writer has never failed, on occasions public or private, to urge his belief that the realization of this idea, deemed by him a certainty of the future, will bring about

Jan 1, 1880

By R. S. Shoemaker, F. W. McQuiston

EMPEROR GOLD MINES Vatukoula, Fiji 1974 Operating Data to July 1 ORE DESCRIPTION: Ore bodies occur in basalt and associated ash beds overlain by andesite tuffs and sediments. The basalt in much of the ore mined is weathered with alteration of olivine to serpentine and iron oxides, and augite to chorite. The most important host minerals for gold are the tellurides sylvanite and hessite. Next in importance the sulphide s, pyrite, marcasite and arseno-pyrite. A small amount of free gold also occurs. Chalcopyrite, sphalerite, tetrahedrite, bornite, galena and native tellurium are present in small quantities. TYPE OF MINE: Underground and open pit ORE HAULAGE TO MILL: 3.5 ton bottom dump skips from underground. 7 ton trucks from open pit. CAPACITY IN TONS/24 HRS: 1345 short tons ASSAY HEADS (1973): 0.232 oz Au per ton, 0.357 oz Te per ton PRODUCTS: Gold Bullion (400 oz bars) Metallic Tellurium (1 2 lb bars ) RECOVERIES: AU 86.2% Te 88.0% ORE GRINDABILITY: 9.25 Kwh/T TOTAL POWER: 25.7 Kwh/T WATER: Pumped 112 mile to a 318, 000 gallon head tank. Consumption: 2 140 gal per ton, no reclaimed water used. TAILINGS: Pumped 2 /3 mile through 8" pipe. Uphill sections are steel. Downhill sections are fibro asbestos.

Jan 1, 1975

By James Aston

A PROPER consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. MANUFACTURE OF WROUGHT IRON The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identified with our modern "Age of Steel" is a relatively brief interval compared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the forerunner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By L. Weaver

THE Tennessee Copper Co.'s mines are in the southeast corner of the state of Tennessee, Polk Co., in the well-known Ducktown copper basin. Their new circular production shaft will eventually be the only ore hoisting shaft, and is located for handling ore from Boyd, Calloway, Mary, and Cherokee mines. A circular, rather than a rectangular, shaft was decided upon because: 1-The circular shaft section is stronger when lined with concrete. Reinforcing steel was not required, thus reducing lining cost by one- quarter. 2-Water sealing was desired; it was thought it could best be done with a concrete lining followed by pressure grouting to eliminate water seeps. 3-The shaft labor saving equipment could best be used in a large opening, so the round section was made for economy, sinking, mucking, concreting and water sealing. Less shaft steel is used than could have been possible with steel sets. There are no posts required; center beams and Tee plate assembly placed at 10 ft hold the 100 lb steel guide rails.

Jan 1, 1950

By Frank E. Woolley, Robert D. Pehlke

Jan 1, 1965

By B. M. Larsen, J. W. Campbell

Several articles have recently been published discussing the conditions necessary for accurate measurements of temperatures in the open-hearth steel furnace. In the course of a study of refractories service conditions in steel furnaces, the present writers have taken temperatures in several open-hearth shops in the Pittsburgh district. The conclusions, as to conditions necessary for accurate measurements of temperature, are somewhat at variance with those of other investigators. The subject is closely connected both with the close control of steel-making and the prevention of overheating of the silica refractories used in roofs and walls. It is becoming more and more important to obtain furnace temperatures of fairly definitely known accuracy. At present, the most useful instrument for such measurements is the disappearing-filament type of optical pyrometer. This method of measurement has formed the basis of most other discussions on the subject and was also used by the writers. Previous Investigations In 1916, Burgess' made perhaps the first systematic series of measurements in steel furnaces. The emissivity figures of 0.40 for liquid steel and of 0.53 to 0.65 for liquid slags had been determined by the Bureau of Standards and were used by Burgess in this work. These correction factors are still being used and are regarded as fairly accurate, so that the tapping and teeming temperatures on metal streams given by Burgess should be very nearly correct. Most of his temperatures of furnace roofs and slag surfaces were taken while flames were present in the furnaces and include a few roof temperatures above 1700' C. (3100' F.).

Jan 1, 1927

By Bruno V. Nordberg

The high cost of coal in Butte and the development of large amounts of cheap electric power from the Missouri river caused the Anaconda Copper Mining Co. in 1908 to make an investigation as to the possibility of adapt- ing this cheap electric power for the operation of their many large hoisting plants. At this time electric power had already been adopted for practically all other power purposes around the mines, such as pumping, compressing air, etc. The map (Fig. 1) shows the location of the mines of the Butte mining district. These mines are located within a circle of approximately a 1-mile

Jan 1, 1914

Jan 1, 1882

ONE DAY IN the mid-1880s, in a suburb 0f Pittsburgh, Pennsylvania, there dismounted from a train the two foremost leaders of the day in the coal and steel industries-Andrew Carnegie and H. C. Frick. Their attention was drawn to a well-loaded car of coke, which their experienced eyes recognized as a superior product. "I'll bet you that coke is from the H. C. Frick Coke Company," Mr. Frick challenged. "I'll bet it was shipped by my company." In a spirit of fun Mr. Carnegie accepted the wager. Mr. Frick lost the bet: the coke had come from M0rewood, one of three sites being operated under the direction of a young entrepreneur, Erskine Ramsay. If Mr. Frick's confidence was somewhat dented by this occurrence, the responsibility was his own. He himself had opened the way for Erskine Ramsay to become the youngest of mine superintendents; and he had dispersed all dissension regarding his choice with the words : "I'm not interested in his years, I'm interested in his record. He makes more coke in an oven than any other superintendent. And I'll take 'em out 0f the cradle if they can make coke... Suppose he is only twenty years old? ... The d --- kid is a genius, I tell you." Erskine Ramsay was to follow in the tradition of Carnegie and Frick. Not only was he ambitious and a worker his background had prepared him for it. Coal mining was in the Ramsay blood. His father, Robert Ramsay, of whom the son once stated that he had no superior as coal mining and mechanical engineer in this country, once accounted in these words for the phenomenal accomplishments which had attached to the name "It does no harm to belong to a family of mining engineers who are just as good as any in America-if it is myself that says it." Anyone acquainted with Robert Ramsay's character realized that he was not given to overstatement. And the above-mentioned Mr. Carnegie encountered young Ramsay again, a few years later in his career, and wrote of him to young Erskine's father, that he was "going to be a credit `tae us a' " (a quotation from Robert Burns.) Nor have Mr. Ramsay's achievements been identified exclusively with the industrial field in which he early asserted himself. He has been an inventor whose techniques in mining engineering have received international recognition. As an investor of foresight, he has benefitted others immeasurably, as well as himself, being an influential factor in the upbuilding of several communities in his chosen and well-loved adopted home state of Alabama since 1887. He is a philanthropist whose benefactions have run into millions, the chief beneficiaries being educational and charitable institutions. Amidst his accomplishments the lighter side of life has not been neglected and he is known for his hospitality, his

Jan 1, 1953

By H. L. TERWILLIGER

THOSE of us who have been following rock drilling work for the last 15 or 20 years can recall some of the problems that were encountered with the old piston type of rock drill and the solid steel which it used. There was frequent trouble in keeping a straight hole in badly broken ground when using the ordinary four- point bit that had a flare on the wings of about 14". The drill steel, when pounding down its hole, would follow the line of least resistance and draw away from the desired line when it encountered a weak side in the ground through which it was drilling. Some would overcome the difficulty by making long winged bits to prevent the steel crowding over; this would relieve the troubles to a great extent. There was trouble with the rifling of drill holes and inability to drill round holes in some ground. The cure for these ills was to use the "X" bit, rather than the crossbit. The "2" bits were brought out in an effort to make it easier to drill a round hole in bad ground. Most of these troubles were before the days when the mechanical drill sharpener was in as common use as it is today. It was not until the introduction of the Leyner type of rock drill, requiring hollow steel that the users of rock drills found themselves confronted with more difficult prob- lems than they had ever encountered before with drill steel because the steel had to stand more severe service.

Jan 1, 1924

By L. A. Walker

DURING the past twelve years the underground shaft of the United States mine at Bingham has been sunk an additional 2000 ft. with stations and pockets cut every 200 ft. without interrupting the mining of 600 tons of ore per day and the advancing of 1500 ft. of development per month. Following is a brief description of the way the joint work is conducted. The vertical underground shaft is a three-compartment shaft with outside dimensions of 6 ft. 4 in. by 15 ft. 6 in., and inside dimensions for each compartment of 4 ft. 2 in. by 4 ft. 8 in. The manway compartment of the main shaft is used as the hoisting compartment in sinking operations; it is partially lined with 2 by 12-in, lagging and a bucket is used without guides or crosshead. Preparatory work includes the placing of a bulkhead in the manway compartment, 60 ft. above the lowest station or level, the installation of a hoist, a head sheave, a fleet sheave, a-signal system, air and water lines, and a trap door for handling waste.

Jan 1, 1937

By E. J. Dulis, A. Kasak, R. C. Westgren

The potential of uirought tungsten- and tantaluw-rich alloys of the W-Ta-Mo-Cb system was investigated for high-strength structural applications above 2500° F. Appreciable strengthening of tung-sten and tantalum—essentially attributable to solid-solzction effects—was obtained with binary, ternary, and quaternary alloys. Tensile strengths as high as 67,000 psi were achieved at 3000 OF. ThE quest for wrought structural materials which possess good strength properties at temperatures above 2000°F has led to a considerable research effort during the past decade. In addition to exploring the potential of various high-melting-point refractory metals (such as molybdenum, columbium, tantalum, and tungsten) for very high-temperature structural applications, alloy-development programs have been undertaken to achieve greater strengths than could be achieved with unalloyed refractory metals. The methods of strengthening refractory metal alloys have included both solid-solution and dispersion strengthening. General relationships among the relevant properties (melting point, recrystallization temperature, and high-temperature strength) of refractory metals indicate that the highest strengths at temperatures of 2500°F or higher would be obtained with tungsten-or tantalum-base alloys. Therefore, the present investigation was undertaken to determine the high-temperature strength potential of solid-solution strengthened alloys based on the binary system W-Ta; to effect further strengthening, minor additions of molybdenum and columbium (at the 6 and 12 pct levels) were made. The portion of the W-Ta-Mo-Cb quaternary alloy system of interest is shown schematically in Fig. 1. The component metals—W, Ta, Mo, and Cb—have a bcc structure at all temperatures, and their binary systems are mutually completely soluble.' Complete solid solubility in the W-Ta-Mo and W-Ta-Cb alloy systems has been demonstrated,' and, therefore, it was expected that the quarternary alloys of the system would also exhibit complete solid solubility at all temperatures. In the virtual absence of contamination by interstitial elements, all the alloys would be truly solid-solution strengthened. Twenty specific compositions of this investigation included binary, ternary, and quaternary alloys of the W-Ta-Mo-Cb system as well as unalloyed tungsten and tantalum. The compositions are shown in Table I. EXPERIMENTAL PROCEDURE Consumable-electrode vacuum-arc melting with ac power was used to produce small laboratory-sized, cylindrically shaped ingots (1-1/4 in. in diameter and 2 to 3-1/2 in. long) of the twenty compositions. A furnace was specially constructed to melt as many as four electrode rods simultaneously into molds lined with tungsten or tantalum sheet. High-purity rods of tungsten, tantalum, molybdenum, and columbium were used for consumable electrodes; the diameter of each rod was determined by the desired weight percentage of the component metal in a given alloy. The details of the construction and operation of the melting furnace will be discussed in another p~blication.

Jan 1, 1964

By D. T. Camp, J. A. Clum

WITH experience, the indexing of back-reflection Laue patterns for cubic crystals is usually a straightforward matter. However, for noncubic systems where in general tables of interplanar angles are not available or when inexperienced personnel are involved, properly indexing a crystal is normally a tedious, time-consuming affair. The authors have written a digital-computer program which calculates and prints out a table of interplanar angles for an arbitrary crystal structure and then systematically searches through this table attempting to obtain a consistent fit to back-reflection Laue data supplied by the user. Of course it is possible simply to calculate a desired set of interplanar angles should this be the only requirement. The program was originally written in ALGOL for use on a Control Data G-21 computer and a preliminary version is described elsewhere.' A version in FORTRAN TV which has been run on an IBM 7040 and one in FORTRAN II run on an IBM 1620 are also available. While it is not the purpose of this communication to describe the program in detail, an indication of how the program operates may help one to decide whether the program would be useful under particular circumstances. The hypothetical example chosen involves the indexing of the zinc crystal which has a hexagonal structure and a c/a ratio of 1.856. Input data for this example consists of only nine cards: The first card controls the list of families of planes to be considered. If the Miller indices of a prospective family are (h k 1), the first digit places a limit, in this case 3, on the absolute values of any individual index. The second digit limits the sum (h +k + l + 1), in this case to 5. Therefore the families (013) and (112) are considered but the family (122) is not. All systems, including the hexagonal, are treated using three-digit Miller indices. The second card contains the crystallographic parameters required to define the system. The first digit is 0 if the system is rectangular, that is all angles are 90 deg. If the system is nonrectangular, as in this example, the digit 1 so indicates. The next three values are the lengths of the sides of the reference cell, a, b, c. The final three entries on the card are the angles, a, 8, y between the sides. The digit 0 on the third card indicates that more data follows, the digit 6 shows that a set of six planes is to be indexed, and the value 2.0 indicates that agreement between a tabulated angle and an input angle is considered adequate if their absolute difference is less than 2 deg. The fourth card lists the measured input angles. a12 = 38 deg, a13 = 24 deg, and so forth. More input angles are listed on cards five to eight with the latter giving the input angle 058 = 40 deg. The final card in this series indicates by the digit 1 that no more data is to be processed. The program operates in the following manner: 1) The input data from cards 1 and 2 is read, thereby indicating the crystal system to be examined and the crystallographic parameters of the particular crystal to be indexed. 2) A table of interplanar angles is generated. 3) The input angles contained on cards 4 to 8 are read. 4) The measured input data is systematically compared with the generated table of standard angles. All combinations of poles whose interplanar angles compare with the requisite, specified accuracy are printed out. If no adequate fit is found an indication of this is printed. A typical line from the generated table of interplanar angles is: (001) - (111) 74.92 64.99 It can be shown that in the Miller-Bravais system the first value corresponds to the angles between (0001)-(1121) and the second to that between (0001)-(1011). This particular set of data gave the following result for the planes 1 to 6: (011) (110) (121) (111) (112) (010) The ALGOL version also has the option of simply providing the Greninger-chart coordinates ? and 6

Jan 1, 1967

By Noel S. Christensen

COBALT is a silvery white metal with a slight bluish cast, strongly resembling nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ quite decidedly in their properties from those of nickel. The name cobalt was derived from the German "Kobold" meaning goblin and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was only isolated about the middle of the eighteenth century by Brandt although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470. The metal is fairly hard, with a density when pure of 8.81 in the cast state and 8.92 after working. The commercial grade of cobalt has a density of about 8.75 in the cast state. The atomic weight is 58.97. The Brinell hardness of the pure metal is 124; that of the commercial grade varies from as low as 100 to as high as 138, depend¬ing upon the impurities present. Pure cobalt has a sharp melting point at 1478°C. The tensile strength of the pure metal in the cast condition is said to be higher than that of any other pure metal. Kalmus gives it as 34,400 lb. per sq. in. for cast unannealed metal; the effect of annealing at 850 to 900°C. is to raise the strength slightly. The yield point is close to the ultimate strength and the reduction in area and elongation are both low. Mechanical working raises the tensile strength of pure cobalt rapidly and in the form of wire it will be over 100,000 lb. per sq. in. The presence of small quantities of carbon in the commercial metal raises the tensile strength to as high as 61,000 lb. per sq. in., the reduction in area and elongation being raised at the same time to approximately 20 per cent.

Jan 1, 1933

By Merrill, Charles White

MOST extraordinary of the technical developments in placer gold mining during the last five years has been the rise of the dragline dredge, by which is meant a floating washing plant for auriferous gravel, fed by a dragline excavator. The idea originated in the fall of 1933, when Horace Onyett constructed a floating washing plant to which gravel was delivered by a dragline excavator standing on dry land. Onyett's operation near Oroville, Calif., and another started by H. F. England later on Wyandotte Creek, Butte County, Calif., yielded '75 oz. of fine gold before the end of 1933. Although the first operation was abandoned shortly as un- profitable, the dragline-dredge method of gold recovery soon began to expand at a boom rate. As a matter of interest, the Onyett operation was taken over later by Lord and Bishop, who are re- ported to have succeeded in making it the first financially successful drag- line dredge. In California alone drag- line dredges produced $3,294,970 worth of gold in 1937, and the pros-

Jan 1, 1938

By Harrison Everett Ashley

(Pittsburg Meeting, March, 1910.) Slimes are usually defined as all material passing a certain-sized sieve, which is invariably the finest sieve employed by each metallurgist in his tests; 100-mesh and 200-mesh have been taken as the limits by different writers in recent volumes of the Transactions ; 150-mesh is common practice. The reader of the first two volumes of Richards 1 is impressed by the inflexibility with which all grinding-arrangements are praised or condemned according as they make little or much slime. Until recently, one of the principal aims of the mill-man was to keep down the slimes. He was obliged to have separate apparatus for sand- and slime-treatment. The latter was sometimes puzzling and erratic. Often it was found most .economical to omit treatment of the slimes entirely, or to store them in immense basins or heaps, waiting for possible future improvements in methods of treatment. Recently, improved processes of agitation and filtration have made possible the successful extraction of values from many slimes. The tendency, when the metal is exceedingly finely disseminated, is to cut out all sand-treatment and to slime everything. These processes have been almost entirely mechanical in their conception, and it is the object of the present paper to show that certain chemical considerations may greatly hinder or assist their successful operation. It has long been a source of dissatisfaction to chemists that their analyses fail to be of much help to the clay-worker; that it is a matter of common occurrence for clays of closely identical ultimate chemical constitution to show the widest possible divergence in physical properties. * Published by permission of the Director of the U. S. Geological Survey. Ore Dressing (1903).

Aug 1, 1910

By AIME AIME

T HE 133rd meeting of the A. I. M. E., opening in New York on Feb. 15, promises to be as successful technically and socially as any in the past. The papers submitted for the various technical sessions are unusually excellent and insure something of interest to every group. Tentative programs have already been issued, and a concise resume of the various sessions, arranged chronologically, appears on page 48. Among the many interesting technical sessions arranged, attention is directed to those of the Petroleum Division, embracing the Symposium on Production that has come to be an annual feature, and new ones on refining practice, transportation and economics. The Institute of Metals program is similarly comprehensive. It includes 15 papers, 8 on copper, 4 on aluminum and its alloys, and one each on magnesium, lead, and fatigue of metals. The Coal Committee offers as a leading contribution its report, prepared under the direction of H. N. Eavenson, giving a new analysis of the capacity of the mines and a comparison of coal with other industries. This will be supplemented by a number of other papers of especial interest to operating men, among which are "Data on Use of Loading Machines in Bituminous Mines," by Graham Bright; "Evaluation of Coal," by R. H. Sweetser; "Selection of Coals for the Manufacture of Coke," by H. J. Rose; and "Relation of Origin and State of Carbonization of Coal to Problems of Low Temperature Carbonization," by S. W. Parr. The Iron and Steel Committee has scheduled seven papers, and there will be a special session on open-hearth practice, in which will be presented the first results of the two conferences, held by the sub- committee at Pittsburgh and Cleveland. A symposium on molding sands will be a special feature of the session on non-metallics.

Jan 1, 1926