Search Documents

NORTH AMERICA ALASKA Anchorage,-Ames, M. B. Culver, H. W. Fiedler, H. L. Fox, E. F. Gallemore, W. A. Kreitlow, E. J. Layfield, R. A. Saarela, L. H. Strandberg. H. Candle,-Bobbins, J. S. College.-Fackler, W. C. Joesting, H. R. Swift. R. E. "Wilcox, H. G.. Crooked Creek-Lyman. R. F. Fairbanks.-Beistline, E. H. CANADA Canadian Army Overseas,¬ Ball, H. D. Brides, C. Butterill. H. J. M. Ladner, F. E. Lane, H. C. Millar, R'. A. Murchison, R. G. Passow, F. M. ALBERTA Calgary-Allen, R. E. de Hart. J. B. Dingman, C. W. Furnical. G. H. Gray, J. G.

Jan 1, 1943

By H. J. Beattie

R. L. Stegman and M. R. Achter (U.S. Naval Research Laboratory)—In a study of the surface structures developed in the fatigue of nickel at low strains as a function of temperature, we have obtained similar results.3 As our apparatus permits fatigue tests to be conducted in vacuo, there was no masking of the surface at high temperatures by oxidation so that the structures there could be observed directly. The relatively few broad slip bands observed at room temperature gave way at 300°C to a large number of uniformly distributed and narrower slip bands. At 550°C deformation began to concentrate around the grain boundaries and progressively increased up to 800°C. In addition fatigue strength was observed initially to increase with increasing temperature up to about 600°C due to the effectively increased ductility caused by the dispersal of fatigue damage. The fatigue strength then decreased at higher temperatures as grain boundary cracking dominates. Maria Ronay, W. H. Reimann, and W. A. Wood (authors' reply)— The authors are pleased to note that R. L. Stegman and M. R. Achter reach similar conclusions from their study of surface slip on nickel. However, they would emphasize that their own conclusions are based on what is shown by study of specimens that have been sectioned and that this study also shows that surface slip is not necessarily representative of what happens below the surface.

Jan 1, 1965

By R. L. Stegman, M. R. Achter

R. L. Stegman and M. R. Achter (U.S. Naval Research Laboratory)—In a study of the surface structures developed in the fatigue of nickel at low strains as a function of temperature, we have obtained similar results.3 As our apparatus permits fatigue tests to be conducted in vacuo, there was no masking of the surface at high temperatures by oxidation so that the structures there could be observed directly. The relatively few broad slip bands observed at room temperature gave way at 300°C to a large number of uniformly distributed and narrower slip bands. At 550°C deformation began to concentrate around the grain boundaries and progressively increased up to 800°C. In addition fatigue strength was observed initially to increase with increasing temperature up to about 600°C due to the effectively increased ductility caused by the dispersal of fatigue damage. The fatigue strength then decreased at higher temperatures as grain boundary cracking dominates. Maria Ronay, W. H. Reimann, and W. A. Wood (authors' reply)— The authors are pleased to note that R. L. Stegman and M. R. Achter reach similar conclusions from their study of surface slip on nickel. However, they would emphasize that their own conclusions are based on what is shown by study of specimens that have been sectioned and that this study also shows that surface slip is not necessarily representative of what happens below the surface.

Jan 1, 1965

By M. C. Manderson

Abstract-The sharp drop in world phosphate demand that took place in 1975, due to temporarily high prices, now seems to be reversing itself. And prices for both phosphate rock and phosphate fertilizers, which declined dramatically from their 1975 highs, now appear to be bottoming out. This recent price weakness has delayed new mining ventures that had previously been planned for completion by around 1980. While there is ample capacity to supply near-term rock needs, the stage seems to be emerging for a better supply-demand and price environment in the late 1970's and early 1980's.

Jan 1, 1978

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft. elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 lb. pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 ½ miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in. Fig. 3.

Jan 9, 1916

By Gerald Edmunds

CASTINGS of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, some-times nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is devel-oped to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and there-fore the position of the grains is more com-plex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicat-ing that thermal contact was better there than in neighboring areas.

Jan 1, 1940

By H. C. Babbitt

The Effect of Arsenic.—A question involving the temperature of precipitation of ammonium phospho-molybdate, which was brought to my attention some time ago, led to the following experiment :*

Jan 1, 1893

The regular activities of the Insti¬tute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $560,000. An active effort is being made to in¬crease the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman; Paul D. Merica, vice-chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, John V. M. Dorr, Howard N. Eavenson, D. C. Jackling, Henry Krumb John M. Lovejoy, Harvey D. Mudd and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1943

By J. A. Cahill, A. D. Kirshenbaum

Using an alumina or zirconia crucible with an alumina sinker or a molybdenum sinker coated with zirconium dioxide, the density of liquid iron was determined by the immersed-sinker method over the temperature range of 1800" to 2500°K. The density, with respect to temperature, is ex-Dressed by the equation Dg/cm = 8.523 - 8.358 X 10 T'K The molar Volumes and thermal coefficients of expansion were calculated. Iron, upon me1ting, was found to expand 3.5 pct. A basic knowledge of the physical properties of materials at high temperatures is becoming increasingly important. A check of the literature shows, that in spite of the importance of iron, very few measurements have been made of its physical properties in the liquid state. Density measurements have been made by Benedicks and his collaborators1g using the method of balanced columns, by Desch and smith4 using the immersed sinker method with an alumina sinker, by Lucas using the maximum bubble method5 and by Stott and endall' who used an alumina pyknometer. In the method of balanced columns, the difference in level of molten iron in two arms of a U-tube, together with the corresponding difference of pressure had to be measured. The formation of gas bubbles in one or both arms was a great source of error. These values are very erratic. They vary from 6.83 to 7.45 g per cm3 at the melting point (1805"~) and from 6.45 to 7.15 g per cm3 at 1890°K. Stott and Rendall determined the density at 1837"K, with a reproducibility of *0.2 pct. They used an alumina pyknometer fired to 1973°K. The vessel was filled in a vacuum furnace by immersion in the liquid metal. When thermal equilibrium was attained, the pyknometer was withdrawn, cooled, the ingot removed and then weighed. The chief disadvantage of the method was the difficulty of inserting the pyknometer without cracking it. The authors have been able to determine the density of liquid iron from its melting point up to 2500°K, by using the immersed-sinker method, with A1203 or ZrOz crucibles and A1203 or molybdenum sinkers coated with Zr02, Fig. 1. EXPERIMENTAL Apparatus. In these studies the source of heat was the carbon tube resistance furnace with an argon atmosphere described previously.7 Experimental runs were made using either Ala3 or ZrOz crucibles. The sinkers used were 1) pure A1a3 and 2) molybdenum coated with ZrOz. The crucible, 2 1/8 in. in diam and 3 in. high, was centered in the furnace on an Ala3 of Zr02 pedestal. The sinker, 1/2 in. in diam and 1 1/2 in. long, together with a counter weight, was suspended from an analytical balance into the melt by a molybdenum wire. Procedure. The procedure, as described previously,' consisted in measuring the weight loss of the sinker in the liquid iron while determining simultaneously the liquid iron temperature by means

Jan 1, 1962

By M. von Heimendahl, G. Thomas

The microstructure of TD-Ni has been examined by transmission electron microscopy in the extruded, annealed. and deformed states. The tensile properties hove been correlated with the observed microstructures and the results ore com-pared with those obtained from pure nickel. The important conclusions are that the thorin particles in TD-Ni act as strong burriers to dislocntion motion during both deformation (slip) and annealing (climb). During deformation. the dislocations tangle around the particles and a cell structure is devleloped after 10 pct or more strain. The cell size appears to be determined by the spacing of the largest particles and is about five times smaller than that in pure nickel for the same strain. The higher work-hardening rate in TD-Ni compared to nickel is probably due to the more rapid rate of dislocation multiplication in the alloy as a result of dislocation-particle interactions. The Th0,particles inhibit recrystallization and twin growh so that some strengthening may arise from the high density of small annealing twins. THE strengthening of materials due to the presence of a dispersed second phase has been the subject of considerable experimental and theoretical investigation in recent years. One of the newest dispersion-strengthened alloys to be developed is TD-Ni,1 a system of approximately 2 vol pct thoria (ThO2) dispersed in a matrix of commercially pure nickel. This material is fabricated by powder-metallurgical techniques and offers high-temperature stability and useful mechanical properties virtually to the melting point of the base metal. While the mechanical properties of this system have been investigated,2,3 there have been no reports in the literature concerning the microstruc-ture of TD-Ni and its correlation to mechanical properties. This paper describes a transmission electron microscopy investigation of the micro-structure of TD-Ni together with its mechanical properties. The results are compared with the structure and properties of pure nickel.

Jan 1, 1964

By J. E. Dinger, Ross Gunn

Faraday's Law of magnetic induction states that the e.m.f. acting around a closed circuit is equal to the time rate of change of flux through that circuit. If the closed circuit is a conducting medium, there will flow an electric current which is propor¬tional to the conductivity of the material and the time rate of change of the flux. Electrical currents so induced in a con¬ducting material are often referred to as eddy currents. Eddy currents are thus induced into a conducting material by (1) a time rate of change of the magnetic field through the material, by (2) a relative motion of the conducting material and a magnetic field, or by (3) a combination of (1) and (2). Because the magnitude of the induced eddy currents is dependent upon the resistance of the equivalent conducting path, these currents offer a method of detecting electrical discontinuities in a

Jan 1, 1945

By R. I. Jaffee, J. W. Roberts, D. N. Williams

DISPERSION hardening as an alloying process has aroused increasing interest in the past few years. This alloying procedure, in which an insoluble phase is dispersed randomly through a metal or alloy, is believed to be especially suited for the attainment of creep strength at elevated temperatures since the dispersed phase is metallurgically stable. Another advantage is that the physical properties of the matrix phase, such as electrical conductivity, remain relatively unaffected by alloying. These two characteristics resulted in interest in the applicability of dispersion hardening to copper and copper alloys. A study of copper alloys prepared by powder metallurgy methods has shown some strengthening from oxide dispersions.' However, powder metallurgy processing would not be economical for large scale production of dispersion hardened copper-base alloys. Therefore, the research described in this article was initiated to examine methods of forming dispersion alloys which would not require powder metallurgy processing. If powder metallurgy processing is to be avoided, a method must be found by which the dispersion material can be introduced into and dispersed through the melt before casting. When the dispersed phase is an oxide or similar nonmetallic, it is extremely difficult to form a satisfactory liquid: solid dispersion since successful mixing requires that the melt wet the dispersed phase. It is almost impossible to force a nonwetted particle beneath the melt surface. This difficulty can be avoided, however, if the oxide particles are produced in molten copper by reaction within the melt. The problem would then reduce to maintaining randomness until solidification. Four procedures were considered for producing an oxide particle within molten copper by reaction. In all cases, the intent was to react oxygen (0) with a reactive metal (X) to form an oxide (XO) within the copper melt. These reactions were as follows: 1) (Cu-X), + (O)g (Cu)1 + (XO)S [1] 2) (Cu-X)1 + (Cu2O)s (Cu)x + (XO)S [2] 3) (Cu-OK)1 + (Cu-X)1 (Cu)1+(XO)9 [3] 4) (Cu-OK)1 +(X)s (Cu)1 +(XO)s [4] The reactions were carried out in an 8-lb melt of 99.98 pct Cu maintained in the vicinity of 2200oF by induction heating. Where possible the amount of the reactants was controlled to give 1 to 5 vol pct oxide. Mechanical stirring during the reaction period was used to minimize agglomeration of the reaction product. The presence of a reaction product was determined metallographically by study of an ingot cast from the melt at the end of the reaction period. Reaction [I] was studied by dissolving aluminum in the melt followed by forcing oxygen through the melt. The melts became quite sluggish during the reaction period suggesting that A12O3 was formed. However, the reaction product rose out of the melt rapidly, possibly due to the flushing action of the oxygen stream, and little dispersed phase was formed. Reaction [2] was examined by dissolving aluminum, silicon, or nickel i; the melt and then adding Cu20 (melting point 2250F). This procedure was unsuccessful. Although Cu2O was easily stirred into cop-

Jan 1, 1961

By P. E. Fitzgerald

ACIDIZING, as the terns is used in the petroleum production industry, involves the use of hydrochloric acid in predominantly limestone formations, resulting in the lowering of resistance offered to the flow of oil and gas through the oil-bearing formation, usually with resultant increased production. A number of articles have been written on the chemical treatment of oil and gas wells; a bibliography of these works will appear in Volume 123 of the Institute's TRANSACTIONS (1937), and a few other references are appended to this paper.

Jan 1, 1937

By Luis Emylnn Salas

If the ordinary wet method be attempted for silver-bullion containing tin, much trouble is experienced, varying with the amount of tin present. Even with a percentage as low as 0.05, the end-point is masked by a persistent turbidity, while with amounts ranging from 0.5 per cent. upward, the determination of the exact end-point is impossible, owing to the finely divided or colloidal metastannic acid resisting all efforts to cause it to settle, or to give a clear supernatant liquid. The object of the following experiments was to seek a remedy for these difficulties, and to find the conditions whereby the Gay Lussac method might be applied directly to these bullions. Material containing tin is met with frequently in bullion from Mexico or Bolivia; and tin is carried (sometimes in large quantities) in jewelers' sweeps. 1. A bullion was prepared containing Ag, 74; Cu, 25; and Sn, 1 per cent. A weighed amount was treated by the humid assay-method as if it were an ordinary bullion free from tin. Ten cc. of HNO, (1.21) was added, and the bottle was heated until all traces of

Jan 1, 1913

By H. E. Nold

THIS paper is an effort to explain in a simple manner the fundamental principles involved in examining a clay deposit for both quantity and quality and in operating a clay mine, either open-pit or underground, so that the best quality of finished material can be made from the raw material available. The writer is aware that what is recommended in this paper is everyday practice in many refractories plants and in some other heavy-clay products plants, but observations made while visiting practically every clay mine in Ohio have convinced him that the practices herein discussed are not as widely used as their importance warrants. It is true that the problem of mining for quality is more acute in refractories plants than in most heavy-clay products plants, yet some of the latter are finding it profitable to pay more than ordinary attention to the selection and blending of their raw materials. It is hoped that this short paper may prove helpful to some who are now finding it difficult to produce a uniform product of as high quality as their clay deposit seems to warrant. The coordination of the work of the clay mine or pit with the manufacturing plant, to the end that the best product possible be made from the raw material available, presupposes a rather intimate knowledge of the clay deposit. The knowledge must include not only information of the amount of clay-available but also rather detailed information about both vertical and horizontal variations in quality of the clay. This information should cover three things: quality, quantity, and location.

Jan 1, 1929

By W. H. Tuttle, H. R. Ahlquist, A. J. Carlson

Variations of the EVOP technique are accepted as the foun- dation in the development of Erie Mining Company's mining, concentrating and pelletizing complex at Hoyt Lakes, Minnesota. The basic one-variable- at-a-time technique served its purpose through the laboratory pilot plant as well as the full-scale production sized pilot plant. However, recognition by Erie Mining Company management of the potential of computer application and statistical experimentation in plant operation and testing led to acquisition of an IBM 1620 computer in 1961. Adaptation of established techniques in statistically designed experimentation and analysis of results is presented in actual case form including the following: 1. Determination and use of variance, standard deviation, standard errors; application of t-test in determining true differences between daily aver ages of product assays; formulation of quality control limits; determining sample size; and application of normality tests will be discussed. 2. Use of mathematical modeling and regression analysis for establishing mill storage conditions based on bin level indicator lights. 3. Polyvariable random balance design of a balling circuit test and resultant identification of primary control variables.

Jan 1, 1969

By Hans W. Schreiber, David W. Neuhaus

INTRODUCTION The Sunshine Mining Company's 16-to-1 silver deposit and mine project are located 384 kilometers (240 miles) southeast of Reno and 360 kilometers (225 miles northwest of Las Vegas, near Silver Peak in Esmeralda County, Nevada, at an elevation of about 2,300 meters (7,000 feet). The deposit was being developed, in 1980, with an anticipated mining and milling rate of 150,000 tons per year (500 tons per day). Mining is by underground, blast-hole open stoping with rubber-tire haul-age out of the mine to a straight cyanide plant about 5.5 kilometers (3.5 miles) from the mine. The product is a gold-silver dore which may be further refined at Sunshine's new refinery in Kellogg, Idaho. The cash required for investment was obtained through the sale of $25 million worth of 6 l/2h silver-indexed bonds. Some $15.0 million were directed toward development of the 16-to-1 Mine. These bonds, which were underwritten by Drexel Burnham Lambert of Chicago in April of 1980, are redeemable on or after April 15, 1985 or payable at maturity on April 15, 1995 at the greater of either $1,000 or the market price of 50 ounces of silver. Behre Dolbear acknowledges the kindness of the Sunshine Mining Company (Sunshine) for allowing the presentation of the subject material for this Case Study. APPLICABILITY AS CASE STUDY Reasons for Choosing 16-to-1 The reasons for choosing the 16-to-1 Mine as a case study follow: 1. The project is simple and compact. 2. The mine is small -- thus relevant to other contemplated precious metal operaions in the western states. 3. The areas of risk are readily identifiable. 4. A change to project financing was under consideration. 5. A substantial decline in the price of silver was experienced during development. 6. Behre Dolbear undertook one of the first feasibility studies of The 16-to-1 and thus has some familiarity with the project. Historical Summary The following history serves as a setting: 1. Late 1920s -- minor "production"(?) via shallow pitting. 2. Mid-1930s -- neighboring Nivlok Mine successfully put into production. 3. Late 1950s (?) -- Callahan Mining Company acquired rights and drilled -- results inconclusive; Callahan turned property back to Arthur Baker, who had originally interested Callahan in 16-to-1 on the basis of its similarity with Nivlok Mine.

Jan 1, 1985

By Nicholas J. Grant, A. W. Mullendore

Measurements of grain boundary sliding were made on polycrystal and bicrystal tensile creep specimens of Al-2 pct Mg at 500oand 700oF. Grain and pain boundary orientation factors were studied with respect to their effect on the magnitude and direction of grain boundary sliding. It was concluded that a large part of the observed sliding may be caused by the operation of slip crossing the grain boundaries. Supporting evidence for this model from other investigations is also given. GRAIN boundary sliding in metals during elevated temperature deformation has frequently been thought of as an independent mechanism with its own characteristic stress, temperature, and structure dependence. Further, it is common to regard the grain boundary as the weak link during creep deformation since: 1) the strength of apolycrystallinemetal, as meas-sured by creep rate or rupture life, decreases at\a more rapid rate when sliding comes into action, and 2) grain boundary sliding, as revealed by "boundary darkening" and fold formation is often the first visible deformation. On the other hand, more quantitative observations, in both polycrystals and bicrystals, have shown boundary deformation to be closely related to the over-all deformation of the specimen. The curve of grain boundary contribution to elongation vs time takes a shape similar to that of the total creep curve,',' and the apparent activation energy for sliding appears in most cases to have the same value as that for total creep.3 In order to reconcile these observations, one is left with these possibilities: 1) The grain boundary and grain deformation rates are both controlled by the same rate limiting processes. 2) The rate of sliding is limited by accommodation deformation in the grains. 3) Sliding is the consequence of grain deformation. 4) Grain deformation is dependent on prior grain boundary deformation. Alternatives 2) and 3) would view grain boundary sliding as occurring in series with another deformation process which could be rate controlling. McLean prefers item 3) as the sliding basis,4 where subgrain rotation results from dislocation accumulation in the substructure at the grain boundary. Crussard and Friedel's5 treatment of grain boundary migration considers that dislocations are forced into the grain boundary and are dissociated into dislocations with Burgers' vectors nearly parallel to the grain boundary. The movement of these partial grain boundary dislocations then produces the sliding. The results of this investigation have indicated alternative 3) to be the most appropriate and it is this aspect of grain boundary sliding which will be analyzed. EXPERIMENTAL PROCEDURE Three types of tensile creep tests were employed in this study: (I) A constant load test of one very coarsegrained polycrystalline specimen at 500° F, 3600 psi, 1 pct per/hr strain rate to examine the grain and grain boundary orientation factors in grain boundary sliding. (II) Constant strain rate tests of polycrystalline specimens at 510o and 715o F, 2 pct per/hr strain rate to determine the grain boundary contribution to elongation at very low total strains. (m) Constant strain rate tests of bicrystals of various grain and grain boundary orientations at 500°F, 2 pct per/hr strain rate to obtain further information on the orientation effects in grain boundary sliding. The material used in the tests was a high-purity Al-1'.92 mg alloy, kindly furnished by Alcoa. Its composition is given in Table I. The alloy is a solid solution at the test temperatures. The coarse grained polycrystalline specimen for test (I) was prepared by recrystallizingthe machined specimen, straining it about 1pct intension at room temperature and annealing at 900°F for 8hr. The constant strain rate specimens (11), with an 178 in. sq. by 1/2 in. long gage section, were cut from 1/8 in. thick sheet of cold rolled and annealed (8 hr at 1000oF) material. The latter specimens were supported in a special jig during the milling operations to avoid any bending, and the gage section was subsequently heavily electropolished to remove the cold-worked surface layer. The bicrystals (ID) were machined in the same

Jan 1, 1963

By J. F. Tavernelli, L. F. Coffin

The deformation and fracture characteristics of eight metals subjected to fully reversed cyclic strain ranging from 0.2 to 50 pct were investigated at room temperature. Strain-hardening characteristics unique to the interna1 structure of a particular metal were found. Complete removal of the strain-hardening effects resulting from prior deformation was brought about by subsequent cyclic strain. Further support for the validity of the inverse relationship between the plastic strain range and the square root of the number of cycles for failure is given. THE resistance of materials to cyclic plastic strain is of interest both from a fundamental and practical point of view. It is now a well-accepted fact that fatigue failure in metals is a consequence of the localized slip deformation which occurs within the individual crystals of metal.'-' Hence the failure process should be strongly dependent upon the magnitude of the gross cyclic plastic deformation of the metal under conditions where this is a measurable quantity. Therefore, an experimental investigation of metals in which the cyclic plastic strain is the independent variable should shed new light on some of the basic aspects of the problem. From the practical point of view, there are many uses for information relating to the cyclic strain resistance of metals. One is the case of thermal stress fatigue where fatigue failure can occur as a consequence of a com- paratively few cycles of thermally induced mechanical deformation. Another is the mechanical working of metals where large cyclic strains are employed. In recent years several publications have appeared relating to the cyclic-strain resistance of metals,8-11 dealing mostly with the fracture aspects where the temperature is cycled simultaneously with the mechanical strain. Some work has been reported on the cyclic-strain resistance of metals at constant temperature, again oriented more toward the fracture aspects of the problem than the deformation aspects. 12-16 The present research investigation was undertaken to obtain information regarding the deformation characteristics of several metals whose structure-property relationships were simple and straightforward under conditions of both cyclic and monotonic strain. It has been shown for example that under cyclic-strain conditions some materials will strain harden, while other materials, particularly cold-worked structures, strain soften and these effects required further clarification.8,17-19 It was also de-

Jan 1, 1960

By LESTER W. STRAUSS

FOR fifteen months after the other dominions of the British Empire and the entire so-called sterling 11loc loosed the shackles that bound the111 to the gold standard, South Africa, giant among gold-producing nations, remained stubbornly attached to gold at the traditional ratio of 85 shillings in currency to one ounce of gold. But eventually even South Africa had to heed the dictates of trade and the obvious interests of its great gold-mining industry. In December, 1932, South Africa's currency severed its golden bonds. Today the South African pound is 011 a par wit11 the British pound.

Jan 1, 1935