Search Documents

By M. Cohen, R. T. Howard

The purpose of this paper is to direct attention to the lower part of the austenite transformation diagram, or TTT curves, where considerable uncertainty still exists as to the blending of the bainite and martensite reactions. The dissimilarities between these two low temperature transforrnations have been summarized recently by Troiano and Greninger.' Of particular importance to the present work is the fact that martensite formation, unlike bainite formation, is not suppressed by the fastest quenching rates attainable. However, most of the investigations in this direction have been concerned primarily with the start of the martensite transformation (Mg) during cooling, rather than with the quantitative aspects of the subsequent reaction on either further cooling or isothermal holding. Several years ago, Cohen2 suggested a form of transformation diagram which reconciled, at least schematically, the isothermal characteristics of the bainite transformation with the insuppressible nature of the martensite transformation. In essence, the diagram consisted of a family of horizontal lines (representing the progress of the austenite-martensite reaction during quenching) which were interrupted in point of time by the bainite family of C-curves extending down from higher temperatures. This picture received later support by metal-lographic3 and dilatometric4,5 studies, but the techniques employed were not sufficiently critical to substantiate some of the details. Elmendorf6 and Grange and Stewardi have shown that the Greninger-Troiano metallographic technique8 may be used not only for M, determinations, but for studying the course of further austenite decomposition. In fact, the latter investigators have observed the amount of martensite formed as a function of temperature below M, in fourteen commercial steels. In the present paper, the Greninger-Troiano technique has been combined with the lineal method of Howard and Cohen9 to provide a unique, quantitative treatment of the austenite-martensite reaction. Furthermore, isothermal transformations have been similarly measured on holding at temperatures above and below M., thus permitting a fairly detailed presentation of the lower part of the conventional austenite transformation diagram. Experimental Details Materials The steels, listed in Table I, were selected for study because they exhibit a satisfactory range of M. temperatures and have not received as much attention as the lower carbon grades. They were prepared as 30 lb induction furnace heats in the laboratories of the Vanadium-Alloys

Jan 1, 1949

By M. Cohen, R. T. Howard

The purpose of this paper is to direct attention to the lower part of the austenite transformation diagram, or TTT curves, where considerable uncertainty still exists as to the blending of the bainite and martensite reactions. The dissimilarities between these two low temperature transforrnations have been summarized recently by Troiano and Greninger.' Of particular importance to the present work is the fact that martensite formation, unlike bainite formation, is not suppressed by the fastest quenching rates attainable. However, most of the investigations in this direction have been concerned primarily with the start of the martensite transformation (Mg) during cooling, rather than with the quantitative aspects of the subsequent reaction on either further cooling or isothermal holding. Several years ago, Cohen2 suggested a form of transformation diagram which reconciled, at least schematically, the isothermal characteristics of the bainite transformation with the insuppressible nature of the martensite transformation. In essence, the diagram consisted of a family of horizontal lines (representing the progress of the austenite-martensite reaction during quenching) which were interrupted in point of time by the bainite family of C-curves extending down from higher temperatures. This picture received later support by metal-lographic3 and dilatometric4,5 studies, but the techniques employed were not sufficiently critical to substantiate some of the details. Elmendorf6 and Grange and Stewardi have shown that the Greninger-Troiano metallographic technique8 may be used not only for M, determinations, but for studying the course of further austenite decomposition. In fact, the latter investigators have observed the amount of martensite formed as a function of temperature below M, in fourteen commercial steels. In the present paper, the Greninger-Troiano technique has been combined with the lineal method of Howard and Cohen9 to provide a unique, quantitative treatment of the austenite-martensite reaction. Furthermore, isothermal transformations have been similarly measured on holding at temperatures above and below M., thus permitting a fairly detailed presentation of the lower part of the conventional austenite transformation diagram. Experimental Details Materials The steels, listed in Table I, were selected for study because they exhibit a satisfactory range of M. temperatures and have not received as much attention as the lower carbon grades. They were prepared as 30 lb induction furnace heats in the laboratories of the Vanadium-Alloys

Jan 1, 1949

By M. T. Erickson, C. A. Rowland

Ball mills 5.5 m (18 ft) in diameter and larger tend to use energy delivered to the mill less efficiently than smaller diameter mills, particularly when the large mills carry 40% by volume ball charges. This paper will explore factors used in scaling up ball mills, showing where the advantages of one factor can possibly be negated by another factor. The paper will propose possible operating limits and areas for further study to establish selection and design limits.

Jan 1, 1985

By N. A. D. Parlee, I. D. Shah

THIS communication reports the results of some work done on the effect of gold, palladium, and platinum on the liquid-gas-solid equilibrium in the Ag-O system,1,2 see Fig. 1. Recently several investigators3, 4, 5 have reported the effects of gold, palladium, platinum, and copper on the solubility of oxygen in liquid silver. This communication represents only a portion of the work done here on the solubility of oxygen in liquid silver and liquid Ag-Au, Ag-Pd, and Ag-Pt alloyss—the greater part having already been reprted. The apparatus, materials, and procedures used were similar to those of earlier work.' l The main precautions observed in obtaining these freezing points at constant temperature and PO2 = 1 atm were as follows: 1) The points were approached very slowly from higher temperatures. 2) In the very near vicinity of the L-G-S equilibrium point precautions were taken to see that the melt was in equilibrium with oxygen at one atm. Equilibrium was considered to have been attained when no more absorption of oxygen was observed in the last 15 min at a fixed temperature. 3) In the case of these alloys, the freezing point of the melt at 1 atm of oxygen and the equilibrium amount of oxygen absorbed by the liquid "infinitesimally" above this point were determined by lowering the temperature in very, very small steps, equilibrating at

Jan 1, 1969

By M. C. Smith, W. V. Green, D. M. Olsen

The creep-rupture behavior of commercial powder-metallurgy molybdenum rod is reported in the temperature range 1600" to 250O°C, at stresses up to 9000 psi and times up to 1 month. The effects of temperature, stress, and grain growth are discussed. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher-stress results reported by pugh.1 BECAUSE of its high melting point, molybdenum should retain useful strength to relatively high temperatures. Combined with its ready availability in the United States, this makes it attractive for many applications in missiles, rockets, and so forth—wherever its susceptibility to oxidation can be tolerated or overcome. The mechanical properties of molybdenum rod in the temperature range —200" to 1540°C have been reported by pugh,' Bechtold,' Parke,3 and Carriker and Guard.4 Madden and chen5 have measured the tensile properties of molybdenum single crystals in vacuum up to about 2500°C. As one further step in evaluating its mechanical usefulness, the constant-load creep-rupture properties of commercial powder-metallurgy molybdenum rod have been investigated in the range 1600" to 2500°C. MATERIAL TESTED Creep specimens were machined from 1/2-in. round commercial molybdenum rod, manufactured from powder by pressing, sintering, and swaging. Spectrochemical analysis of the rod showed "traces" (less than 0.01 pct) of silicon, aluminum, chromium, iron, and zirconium, and "faint traces" (less than 0.001 pct) of manganese, magnesium, cobalt, and nickel. Carbon content was 130 to 200 ppm, nitrogen was 110 to 180 ppm, and oxygen 30 to 35 ppm. A typical microstructure of the as-received rod is shown in Fig. 1. Room temperature tensile properties for five specimens strained at about 0.015 in. per in. per min are shown in Table I. CREEP SPECIMENS USED The specimens used for creep-rupture testing are illustrated in Fig. 2. The 1/4-in.-diam gage section was 3/4 in. long, and terminated at shoulders 5 mils high. These shoulders served as fiducial marks for optical strain measurements. Surface finish on the gage section was 16pin. r.m.s. One specimen, for a "long-time" test described below, was modified by dividing the 3/4-in. gage length into three 1/4-in. long sections with individual diameters of 0.250, 0.230, and 0.210 in., each terminating in a pair of fiducial shoulders. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.6 In it the specimen is held vertically on the axis of a cylindrical tantalum or tungsten heater tube by threaded molybdenum or tungsten grips. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. The bottom specimen grip is held at its lower end by a clevis pin. The testing load is applied to the specimen through the upper grip by means of hanging weights, a constant force-multiplication lever system, and a pull rod sealed to the chamber lid by a bellows. The incandescent specimen is viewed by an external optical system through slots in the heater-tube and radiation shielding, and an enlarged image of it is projected on a ground-glass screen. Gage-length measurements are made on this image with a pair of cathetometers. Thorium oxide coatings were applied to the threaded ends of most specimens, to prevent diffusion-welding of specimens to grips during testing. Without such a coating welding usually occurred, and grips were often broken by subsequent efforts to remove the tested specimens.

Jan 1, 1960

By A. S. Callen

These iron mines of Spain are located on the mountain ridge forming the boundary between the Teruel and Guadalajara provinces, called Sierra Menera. They form a property of 25 mines extending over an area of 1,677 hectares (4,140 acres) situated at a height varying from 1,200 m. (3,940 ft.) to 1,500 m. (4,920 ft.) above sea level. The deposit follows the direction north to south; huge masses of ore are being found both on the slopes and at the summit of the Sierra. The ore occurs among quartzites and magnesite limestone, in some places overlaid by quartzite 15 m. (50 ft.) thick; in some others (and this is more general) the ore is overlaid by earth and boulders of quartzite origin; this layer is about 8 m. (26 ft.) thick. The ore beds occupy the geological horizon of the Superior Trias or Muschelkask, which are here in direct contact with the Silurian quartzites. The lime-stones have been more or less transformed. There is ample evidence to show that these mines were worked in very ancient times—objects and tools employed in mining by the ancient Romans and Arabs are to be found plentifully in old workinigs which extend down into the deposits. It has been estimated that more than 10,000,000 tons of ore were mined in the old days in this district and carried to the primitive forges in the vicinity where iron of much renown in Spain was extracted. Remains of more than 20 of these forges are found in the neighborhood of Sierra Menera and are usually situated near waterfalls and forests. Much investigation has been carried on for the purpose of determining the quantity of ore to be found in these mines, but no exact calculations can be made at present. When the investigation is completed it will surely be found that the deposit contains a much larger quantity than the 100,000,000 tons indicated by the present workings. The mines are now worked as open quarries and this method can and will be followed for a long time, probably until the deposit is worked out. Figs. 1 and 2 give some idea of the quarries in operation and the reserves, the iron-ore stocks, screening installation and general arrangement. From these quarries 1,000,000 tons can be mined annually (987,000

Jan 1, 1916

By AIME AIME

THE luncheon of the Milling Methods Committee in the Engineers' Club, on Feb. 16, was distinctly a social affair, although several matters of a non-milling nature were fruitfully discussed. The session* on Milling Methods, the same afternoon, attracted a gathering which overtaxed the capacity of the Board Room on the fifteenth floor. Galen H. Clevenger presided, with the moral reinforcement of Charles Butters. As all papers were available in printed form, and since synopses have appeared in MINING & METALLURGY, it is unnecessary to cover the contents of each in detail here. The first paper (T. P. 410), by Leaver and Woolf, on the "Flotation of Minor Gold in Large-scale Copper "Concentrators," was excellently summarized by R. S. Dean of the U. S. Bureau of Mines, who stressed the -very definite action of lime as a depressant of gold, and showed how the authors had worked out the best conditions of alkalinity, pH concentration and reagents for -optimum recovery of gold along with base metals, especially where lime had to be used to depress pyrite. No discussion was evoked.

Jan 1, 1931

By A. B. Tanner

The effects of radon in drillholes on gamma-ray logs have been described by L. S. Hilpert and C. M. Bunker1 Since these effects may cause drastic error in the evaluation of uranium deposits, it is useful to know the conditions under which significant amounts of radon tend to accumulate in drillholes. In the studies described here, atmospheric conditions were found to dominate in the control of the behavior of radon in drillholes in the vicinity of a uranium orebody. The site of the investigation was in McKinley County, New Mexico, about 12 miles north of Grants. Drillholes of 4 1/4-in. diam, on 25-ft and 100-ft centers, penetrate ore in dry rock at a depth of about 100 ft. A geologic log of the drillhole of primary interest is shown in Fig. 1. Gamma-ray logs revealed three zones of ore-grade mineralization in the Todilto limestone. A 6-ft zone, the lowest of the three, assayed 0.20 pct U3O8 by chemical analysis. The limestone ores in this area contain disseminated uraninite and some yellow and orange secondary minerals. Only radon"", a member of the uranium'" series, was measured in this investigation. Radon is one of the chemically inert noble gases and is radioactive by alpha particle emission with a half life of about four days. In this discussion, amounts of radon are expressed in microcuries (1 microcurie equals 37,-000 disintegrations per sec) and concentrations of radon are expressed in microcuries per liter of drillhole air. Samples of air were obtained by lowering a sampling device (Fig. 2) into a drillhole and actuating the device at the desired depth. It was then raised to the surface and the sample was transferred to a storage tube. Within two days the sample was transferred to an ionization chamber, and the activ- ity of radon and its short-lived daughter products was measured at radioactive equilibrium with a vibrating-reed electrometer. The measurements were corrected back to the time of collection and involve errors estimated generally not to exceed + 5 pct to —15 pct. Radon Behavior in a Covered Hole: Fig. 3, a typical log of radon concentration vs depth in the covered drillhole, was made by using values of radon concentration at discrete depths. Continuous logs of alpha-particle radiation in the drillholes showed that such radon logs depict the continuous variation of radon concentration with depth quite accurately. Three features of radon logs were noted: 1) maximum

Jan 1, 1960

By AIME AIME

ALL sessions of the Mining Geology Committee at the Annual Meeting this year were held jointly with other groups, a plan that seemed to work out to the satisfaction of every one. Certain of these sessions are reported in this issue by others; the ones held on Wednesday are covered here. Ten papers, as published in the February M&M, were on the program for the Wednesday morning session, held jointly with the Society of Economic Geologists. Mr. Eckel made a brief presentation of his paper, on which there was no discussion, and Mr. Peoples presented that of which he was a joint author. D. M. Fraser then discussed a gravimeter survey for chromite in Cuba, which blocked out some 50,000 tons of ore, and F. G. Wells told of work on chromiferous sands in Oregon.

Jan 1, 1943

By A. T. Shurick

WHATEVER the outcome of the Industrial Recovery Act, it has currently injected the first hope and optimism into the coal industry for more than a decade. Compared with the recent drab years the results are impressive: Bituminous production for the first ten weeks, 78,000,000 tons, may be compared with 63,000,000 last year; anthracite, 14,600,000 tons and 9,600,000 tons for the same periods, respectively, bringing the heaviest payrolls in ten years with individual checks reminiscent of former boom times. Hurried calls for long deferred new equipment and replacements have stimulated foundry and machine works and the -invigorating effect on the railroads is indicated by the first actual car shortage in a decade. And even in the welter of confusion over code prices, this heavy tonnage has moved at the most profitable figure the coal man has realized for many years, though with the large volume on old contracts, profits were not as large as many think.\

Jan 1, 1934

By E. N. Cameron, H. M. Bannerman

During the years 1942-1934, about 125 New England deposits were mined for sheet and punch mica, and many others were briefly prospected. During this period the Geological Survey, United States Department of the Interior, carried on detailcd studies of the deposits and the pegmatite bodies that contain them. The primary purpose of the studies was to provide geological information that would contribute toward efficient mine development and operation. The studies were aimed directly at practical production problems. Detailed maps showing the structure of the deposits were prepared, and geological findings were closely correlated with data on specific yields and costs of mining and processing. The result is information that permits a reasonably accurate appraisal of the mica deposits of New England and the mining industry that they support. At a time when the future of the industry is in doubt, it seems desirable to submit this appraisal for consideration. Domestic mica deposits supply only a small fraction of the country's needs in normal times? for only the richest domestic deposits can compete with the low-cost mines of India and Brazil. However, the possibility that this country may be cut off from its supplies in time of war gives domestic deposits an importance much greater than their peacetime production would imply. New England supplied about 22 per cent of domestic output in 1943 and 1944, the peak years of wartime production. Its actual contribution to the war effort was greater, for the proportion of sheet mica of high quality in the New England product is higher than the average for domestic mica. The data analyzed below were collected for the Geological Survey by D. M. Larra-bee, A. H. McNair, J. J. Page, V. E. Shai-nin, G. W. Stewart, and the co-authors of this paper. The cooperation of officials of Colonial Mica Corporation and of mine operators and owners in furnishing information is gratefully acknowledged. D. M. Larrabee, A. H. McNair, and V. E. Shainin have made various suggestions based on critical reading of the manuscript. Analysis oF Warrtime Operations In considering the data presented in this report, it must be remembered that the scale of mica operations is very small compared with that of many other mining industries. The typical New England mica mine of 1943 and 1944 was worked by a crew of five or six men. Equipment was varied but on the whole extremely simple. The first stage of operation at a deposit was normally opencut mining. Drilling was done mostly with jackhammers powered by portable compressors driven by gasoline engines. Muck was shoveled by hand into buckets with a capacity of 45 to 35 ton and commonly hoisted by derrick to a dump adjacent to the cut. As operations were carried to greater depth, and the tram sition to underground mining was made, these methods were modified to a degree depending largely on the attitude of the deposit mined. At steeply dipping deposits,

Jan 1, 1948

By H. M. Bannerman, E. N. Cameron

During the years 1942-1934, about 125 New England deposits were mined for sheet and punch mica, and many others were briefly prospected. During this period the Geological Survey, United States Department of the Interior, carried on detailcd studies of the deposits and the pegmatite bodies that contain them. The primary purpose of the studies was to provide geological information that would contribute toward efficient mine development and operation. The studies were aimed directly at practical production problems. Detailed maps showing the structure of the deposits were prepared, and geological findings were closely correlated with data on specific yields and costs of mining and processing. The result is information that permits a reasonably accurate appraisal of the mica deposits of New England and the mining industry that they support. At a time when the future of the industry is in doubt, it seems desirable to submit this appraisal for consideration. Domestic mica deposits supply only a small fraction of the country's needs in normal times? for only the richest domestic deposits can compete with the low-cost mines of India and Brazil. However, the possibility that this country may be cut off from its supplies in time of war gives domestic deposits an importance much greater than their peacetime production would imply. New England supplied about 22 per cent of domestic output in 1943 and 1944, the peak years of wartime production. Its actual contribution to the war effort was greater, for the proportion of sheet mica of high quality in the New England product is higher than the average for domestic mica. The data analyzed below were collected for the Geological Survey by D. M. Larra-bee, A. H. McNair, J. J. Page, V. E. Shai-nin, G. W. Stewart, and the co-authors of this paper. The cooperation of officials of Colonial Mica Corporation and of mine operators and owners in furnishing information is gratefully acknowledged. D. M. Larrabee, A. H. McNair, and V. E. Shainin have made various suggestions based on critical reading of the manuscript. Analysis oF Warrtime Operations In considering the data presented in this report, it must be remembered that the scale of mica operations is very small compared with that of many other mining industries. The typical New England mica mine of 1943 and 1944 was worked by a crew of five or six men. Equipment was varied but on the whole extremely simple. The first stage of operation at a deposit was normally opencut mining. Drilling was done mostly with jackhammers powered by portable compressors driven by gasoline engines. Muck was shoveled by hand into buckets with a capacity of 45 to 35 ton and commonly hoisted by derrick to a dump adjacent to the cut. As operations were carried to greater depth, and the tram sition to underground mining was made, these methods were modified to a degree depending largely on the attitude of the deposit mined. At steeply dipping deposits,

Jan 1, 1948

By W. G. Oldham

By monitoring the capacitance of abrupt p-n junctions it is possible to follow the motion of substitu-tional impurities. A p-n junction is formed by growth of silicon from an Al-Si alloy on an n-type silicon sutstrate at a temperature in the range 650" to 750°C. The diodes are etched and sorted for consistent V-I and capacitance behavior and separated into groups. After irradiation, each set with an unirradiated control set is annealed to various temperatltres for 10 mm and the capacitance remeasnred. For very heavily doped diodes (-1019 per cm3) observable capacitance changes occur at neutron fluences of >1015 per cm 3. The results may be interpreted in seceral ways, the simplest of which is to assume simple vacancy diffiision with small impurity -racancy interaction (at the diffiision, i.e. annealing temperature of 700°C). In this interpretation it is found that a typical vacancy makes about 1024 jumps and travels about 10-5 cm before disappearing. The required effective annihilation center density is about 1016per cm3 . Estimates of the vacancy-impurity interaction can be made and the above numbers correctecl, but for arty reasonable assumptions the number of vacancy sinks connot be much reduced. ThE complete annealing of radiation induced defects requires that the vacancies and interstitials either recombine, travel to the surface of the crystal, or travel to an annihilation center, e.g., a dislocation or a precipitate. If the interstitial is ignored except as a possible vacancy annihilation center at low temperatures,* the motion of vacancies may be followed by monitoring the corresponding motion of substitutional impurities. pfister2 has measured the enhanced diffusion of impurities in an asymmetric shallow diffused silicon structure by optically monitoring the junction movement. In these experiments we monitor instead the capacitance of a heavily-doped deep symmetric p-n junction. The sensitivity for this method is several orders of magnitude higher than in Pfister's technique, mainly for two reasons: 1) the junction capacitance of a heavily-doped junction is sensitive to impurity movements in the Angstrom range* com- and 2) the junction may be far from the surface which is a major annihilation center for vacancies. THE EXPERIMENT A p-n junction is formed by the epitaxial growth of silicon from an A1-Si alloy on a silicon substrate at a temperature in the range 650° to 750°C. The technique used is the transport of an aluminum melt through a temperature gradient.4 A 10-mil thick aluminum disc is sandwiched between two silicon wafers and the assembly raised to about 650° C with a temperature gradient normal to the sandwich. After about 8 hr the upper (hotter) wafer has been entirely transported and deposited epitaxially on the substrate wafer. The substrate and overgrowth resistivity are measured with a 4-point probe. The as-grown structure is lapped until the wafer is about 1/2 mm thick with the junction in the center. Contacts consisting of electroless nickel covered by electroplated rhodium are applied to both the p and n sides. The wafer is diced into square dice 1/2 to 1 mm on a side and the dice are etched sufficiently to remove approximately 1 mil of silicon. The following results are all for aluminum (p-side) and antimony (n-side) doped specimens with NA =3x 1018 per cm3, ND = 2-8 x 101A per cm3. The diodes are sorted for consistent V-I and capacitance behavior and separated into groups. After irradiation, each set with an unirradiated control set is annealed and the capacitance remeasured. A special capacitance measurement method is used to insure a low sensitivity to shunt resistance. The diode is voltage driven and the current monitored by a phase lock amplifier. It is possible to adjust the detector phase to a point where shunt resistances as low as 100 O have no effect on the reading. The diodes in this study have a capacitance in the range 1000 to 5000 picofarads and a shunt resistance in the range 100 to l06 O depending on the stage of the anneal. THEORY The theoretical problem is twofold: 1) The computation of the amount of impurity diffusion and hence the impurity profile resulting from a given amount of vacancy motion, and 2) the computation of the capacitance from the impurity profile. A comparison of the theoretical and experimental capacitance (in particular the changes) yields the amount of vacancy motion. Vacancy Motion. A convenient parameter to measure the total amount of vacancy motion is Jv the total number of vacancy jumps per unit volume. Although this parameter varies with position in the crystal, owing to vacancy annihilation at the surfaces, it is approximately independent of position far from the surfaces, i.e. in the junction region. In terms of the number of vacancies per unit volume Nv and the vacancy diffusivity given by

Jan 1, 1970

By Kenneth L. Temple

ACID coal mine drainage presents a peculiarly difficult problem for two principal reasons. First is the fact that the amount of acid water discharged from active and abandoned mines constantly in- creases as coal fields are developed and thereby creates a steadily worsening nuisance of rapidly growing importance to the general public as well as to the coal industry. Second is the even more significant fact that there is no method yet known that will appreciably alleviate the acid water problem except at totally prohibitive cost to the coal operators. The problem is thus seen to be an urgent one. With a growing need for good quality water and a growing public demand for abatement of stream pollution, a large portion of the soft coal industry finds itself in the position of year by year dumping more and more acid into the streams and waterways and having no way in sight of improving the situation or even of keeping it from getting worse.

Jan 12, 1951

By C. H. Mathewson

ABOUT fifty pages of Henry M. Howe's profound treatise, "The Metallography of Steel and Cast Iron," are devoted to twinning with special reference to the origin, nature and general significance of the Neu-mann bands in ferrite. Howe believed with Osmond and Cartaud1 that the Neumanns are mechanical twins and his careful observations leave no doubt that these straight-sided narrow bands habitually occur parallel to trapezohedral planes of form {211}. Attempts to develop the structure of the bands by various methods so that their identity could be established beyond question have not been conspicuously successful. Howe thought that they deflected slip bands. Some of the etching figures which have been developed within and adjacent to Neumann bands support the contention that they are twins. A good example of this effect in ferrite containing 0.6 per cent. of nickel and 1.3 per cent. of phosphorus, originally due to Harnecker and Rassow,2. was reproduced in the 1928 lecture before the Institute of Metals Division on twinning in metals.3 In this case, the sides of the figures might represent the traces of cubic planes laid bare by etching a properly oriented grain of ferrite, twinned along a plane of form 12111. Our own observations in this direction may be represented by Fig. 1 which shows in a deeply etched cavity in the boundary region between a Neumann band and the original crystal two small crystal surfaces which resemble the faces meeting at a reentrant angle in the simple cube twinned along a bisecting plane of form {211} as sketched in Fig. 2. Rosenhain and McMinn4 in 1925, after a careful study of slip bands in ferrite containing Neumanns previously produced by shock, concluded

Jan 1, 1928

By G. H. Edmunds, C. H. Mathewson

About fifty pages of Henry M. Howe's profound treatise, "The Metallography of Steel and Cast Iron," are devoted to twinning with special reference to the origin, nature and general significance of the Neumann bands in ferrite. Howe believed with Osmond and Cartaud1 that the Neumanns are mechanical twins and his careful observations leave no doubt that these straight-sided narrow bands habitually occur parallel to trapezohedral planes of form {211). Attempts to develop the structure of the bands by various methods SO that their identity could be established beyond question have not been conspicuously successful. Howe thought that they deflected slip bands. Some of the etching figures which have been developed within and adjacent to Neumann bands support the contention that they are twins. A good example of this effect in ferrite containing 0.6 per cent, of niekel and 1.3 per cent. of phosphorus, originally due to Harnecker and Rassow,2 was reproduced in the 1928 lecture before the Institute of Metals Division on twinning in metals.3 In this case, the sides of the figures might represent the traces of cubic planes laid bare by etching a properly oriented grain of ferrite, twinned along a plane of form (211). Our own observations in this direction may be represented by Fig. 1 which shows in a deeply etched cavity in the boundary region between a Neumann band and the original crystal two small crystal surfaces which resemble the faces meeting at a reentrant angle in the simple cube twinned along a bisecting plane of form (211) as sketched in Fig. 2. Rosenhain and McMinn4 in 1925, after a careful study of slip bands in ferrite containing Neumanns previously produced by shock, concluded

By Blake M. Loring

RECENTLY the S-curves for 30 to 40 alloy steels have been published.1,2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.20 percent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr. at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1 1/4 by 1/2 by 1/8 in. Wires attached to the samples were used for handling, instead of tongs, to avoid chilling. The specimens were heated at 845°C. for 1/2 hr. and quenched into constant-temperature salt baths held at various temperatures from 205° to 650°C. The time required to transfer the specimens was found to be about x 1 1/2 sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 21°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1941

By Joseph T. Roy

MINING revival during the last few years has brought about a considerable increase in the number of gold and silver determinations made, noticeable in all branches of the industry but especially so in the business of a custom smelter. At East Helena, solely a custom smelter the assay department found that the four assay furnaces available were inadequate to handle the increased amount of work. These furnaces were of a standard design, having duplex muffles, one superimposed on the other; each muffle was 12 1/2 in. wide, 18 1/4 in. long and 6 in. high, and could handle 72 cupels or 20 fusions. Since the heat varied considerably between the upper and lower muffles, cupellations were not ruin in both at the same time. To speed up assaying, E. A. Meale, chief chemist, had the happy idea of enlarging a muffle furnace, originally designed by the Montana Power Co., so that one muffle would acconmmodate at least as many determinations as the duplex muffles. An order was given to the Denver Fire Clay Co. for a Carbofrax muffle of the size required and the local engineering department enlarged the furnace to accommodate the muffle. Details of the

Jan 1, 1938

By A. U. Seybolt

The pressure-temperature relations required to maintain the existence of Si3N4 in silicon-iron of 0.44-11.7 pet Si have been partially explored. The critical data obtained have allowed the calculation of some thermodynamic quantities, and have shown evidence of an order-disorder two-phase field extending at 800°C from about l pet to 5.5 pet Si. THE presence of silicon nitride in electrical sheet, nominally about 3 1/4 pet silicon, balance iron, has been described by several authors'" but there has been some discrepancy among them regarding the identity of the nitride. Also, little has been reported on the quantitative thermodynamic prop- erties. In the work to be reported here, the nitride has been found to be more stable than described by Corney and Turkdogan." Several silicon nitrides have been described in the past, including SiN, Si3N4 and Si2N4 (see, for example, Abegg6 and Pascal7). However, the literature on nitrides other than Si,N, is all very old. No recent investigators using the more powerful tools available today have reported the presence of any nitride other than S3,N4. W. B. Hicke and L. R. Brantley8 in 1930 determined the dissociation pressure of Si3N4 which they made by reacting nitrogen

Jan 1, 1959

By Oscar A. Glaeser

INDUSTRIAL relations in the United States Smelting Refining and Mining Company's Western operations covers the field of personnel and labor relations, and the principal aims are to render service to the employes of the Company and to its operating departments. Accident prevention Safety is a primary function. A safety engineer is employed at each operation. The wholehearted support of Company officials, staff, and the working force has been most successful in preventing accidents. Constant vigilance has been combined with a policy of building safety into all operating activities whether these are in the construction of a new facility, the developmnt of a mining system, or the direction of the working force. That this policy has produced results is attested to by the fact that the accident frequency rate at the Company's major mining operations in Utah has been reduced approximately 75 per cent in the ten-year period ending Dec. 31. 1946.

Jan 1, 1948