Search Documents

By E. H. Phillips, A. F. Keenan

6.2-1. Historical Development. Hammering on hand-held drill steel was the earliest type of percussion drilling. It was not until 1838 that Singer developed a steam-operated drilling machine that lifted a drilling bar and let it drop by gravity. J. J. Couch of Philadelphia patented the first percussion drill in 1849. His machine was a steam drill which literally hurled the drill bar at the rock and retracted it by means of a ratcheted wheel. Later J. W. Fowle added automatic rotation of the steel. In 1871, Simon Ingersoll patented a rock drill mounted on a tripod which permitted drilling holes at any angle, vertical to horizontal. Up to the turn of the century, percussion drills in use were piston-type drills. The drill steel was solid and attached to an extension of the drill piston. Hole cleaning was accomplished by the pumping action of the steel in the hole. Down-holes were drilled wet and cleaned with a blow pipe while up-holes were drilled dry, allowing the cuttings to drop out by gravity. The forerunner of our present hammer drill was the free-piston drill which was first patented in 1884, by Sargent. Because solid drill steel was used, it did not successfully clean down holes. J. G. Leyner solved the problem of applying the hammer drill principle to down-hole and horizontal-hole work in 1897. The key was to pass com- pressed air and water through hollow drill steel to clean the hole. Leyner's work on valves and rotation mechanisms increased the blows per minute of hammer drills from 300 or 400 up to 1800 and more blows per minute and made possible the first lightweight drilling machines. The development of automatic feeds followed. 6.2-2. Percussion Drills. TYPES OF DRILLS. There are two types of percussion drills in use today; the piston drill and the hammer drill. In the

Jan 1, 1968

By Orville R. Lyons

THE removal of moisture from coal has been a coal-preparation problem ever since the first wet-washing preparation plant was placed in operation. Today, when most of the coal produced in the United States is wetted at the working face when mined, or is cleaned by wet methods, the removal of moisture is a necessity for any one or a combination of the following reasons; (1) to avoid freezing difficulties during shipment, (2) to increase the B.t.u. content, (3) to effect savings in freight costs, and (4) to so improve the coal that it may be used for specific purposes-for instance, in the production of briquettes or the production of metallurgical coke-or so that it can be treated by dry cleaning methods. In general, the amount of water retained by coal particles varies with the size-consist of the coal. Fine coal has a larger surface area per unit weight than does coarse coal, so its capacity for retaining moisture is proportionately greater. The removal of moisture from coarse coal is relatively easy, while the removal of water from minus 10-mesh coal or finer is a major problem, usually requiring an individual solution at each preparation plant. As a result, a multitude of methods and a variety of equipment have been designed to solve both general and specific moisture-removal problems. Definitions In order that misunderstanding may be eliminated insofar as possible, it is necessary to define the terms to be used. The moisture content of any given increment of wet, washed coal is made up of two parts, inherent and surface moisture. Inherent moisture has been defined in various ways and as yet no standard definition has been agreed upon. However, in general, it is considered as the moisture that is present in the coal in the bed. The important point to remember is that coal with any amount of inherent moisture, whether 2 or 20 per cent, will appear dry if there is no surface moisture. Also important is the fact that inherent moisture can be removed, in part, by air drying at atmospheric temperatures. Surface moisture is that attached to the surface of the coal particles or that retained in cracks and fissures other than capillary openings in the coal substance. Essentially, insofar as the bituminous coal and anthracite indus-

Jan 1, 1950

By C. W. Volek, G. Mandl

Steam-injection tests in the field have shoum that heat transport into the oil/water region, ahead of the steam zone, may have a significant effect on the production process. Earlier theoretical work on reservoir heating by hot-fluid injection can be used to describe the growth of the steam zone, but only if heat transport from steam zone into oil/water region is neglected. It therefore became necessary to re-examine and extend the earlier theory. It was found that this theory ceases to be consistent with the physical model of the process at a certain critical time, tc, which depends on reservoir thickness, temperature, and quality of the steam. The critical time marks an important change in the heat flow across the condensation frovt: the heat flow, which is purely conductive during 0 < t < tc&apos; becomes predominantly convective at t = tc. Accordingly, at t = tc, the equation which governs expansion of the steam zone changes. On the basis of the new equation, an approximate description for the steam-zone growth during t > tc is developed by making use of upper and lower bounds for the exact solution of the problem. The boundary conditions for heat and mass flow inside the oil/water region are established, and a simple method of detennining the saturation at the downstream side of the condensation front is presented. Experimental results show that the theory gives an accurate description of steam-zone expansion before the critical time. At times near critical time, and also after critical time, experimental data show theoretical steam-zone volumes to be high. Even so, the accuracy of the calculated steam-zone volumes is sufficient for practical purposes. THEORY OF STEAM-ZONE GROWTH INTRODUCTION The engineering evaluation of steam-drive processes is based mainly on a mathematical description of reservoir heating by hot fluid injection presented several years ago by Marx and Langenheim.l This theory can be used to determine the growth of the steam zone,2 provided the flow of heat from the steam zone into the liquid zone ahead of the condensation front (Fig. 1) is neglected. Since we must expect, however, that heat transport into and inside the liquid region (the region between condensation front and production wells) will affect both the water/oil flow and the growth of the steam zone, it is necessary to re-examine and to generalize the Marx and Langenheim theory as applied to steam drive, which will hereafter be termed the "old" theory. Observations made in several field tests emphasize the need to study the heat flow across the condensation front (CF). On several occasions it was discovered that heat was transported in the liquid zone far ahead of the advancing CF, resulting in an early breakthrough of warm water. This seems to occur most often when high injection pressures are applied, when "wet" kONINKLIJKE/SHELL EXPLORATIE EN PRODUKTIE LABORATORIUM RIJSWIJK, THE NETHERLANDS SHELL DEVELOPMENT CO. HOUSTON, TEX.

Jan 1, 1970

By A. Rosen, P. Wynblatt, J. E. Dorn

The temperature, strain rate, and structure dependence of the flow stress in a poly crystalline Fe-2 pct Mn alloy was investigated between 77" and 370°K. It was possible to identify the low-temperature data from 77° to 160°K with Dorn and Rajnak&apos;s theory of the Peierls mechanism of plastic deformation. Above 160°K one or more thermally activated mechanisms must he operative; however, these were not identified in this investigation. The mechanistic basis for the rapid decrease in the flow stress of bcc metals with an increase in temperature over the low-temperature range is yet being debated. Various dislocation mechanisms have been suggested in the past but the agreement between the various proposed theories and the experimental results have not been definitive. In the present paper, the authors will demonstrate that the plastic behavior of polycrystalline iron containing 2 wt pct Mn plus interstitials agrees excellently with predictions based on the Peierls mechanism from 77" to 160°K whereas from 160" to about 370°K other as yet unidentified thermally activated mechanisms take over. Undoubtedly, the overlap of these mechanisms with the Peierls mechanism contributed to the difficulties of rationalizing the low-temperature behavior of iron and its alloys. I) EXPERIMENTAL TECHNIQUES AND RESULTS Although extensive data are now available on the effect of temperature and strain rate on the flow stress of various bcc metals and alloys, it was, nevertheless, deemed necessary for the objectives of the present study to obtain highly accurate data of the type most pertinent for checking the theories on a series of well-documented work-hardened states. Iron containing 2 wt pct Mn was used in this investigation in order to obtain a lower ductile to brittle transition temperature than that for iron.&apos; The additional elements present were 0.004 pct C, 0.05 pct 0, 0.004 pct S, 0.003 pct P, 0.006 pct N, and 0.001 pct Si. The as-received 3/8 by 3/4 in. bars were cold-rolled to 0.100-in. thickness, recrystallized under argon for 30 min at 1073"~, further cold-rolled to 0.063-in. thickness, and finally recrystallized under argon for 30 min at 1000°K. This treatment gave a stable reproducible equiaxed grain structure having an average grain diameter of about 90 p. Prior to the final recrystallization treatment, the sheet was machined into tensile specimens 1/4 in. wide having a 1.625-in.-long gage section. All specimens were tested in controlled-temperature baths on an Instron Testing Machine. For convenience in the theoretical analyses the data will be given in terms of the shear stress for flow, 7, the shear strain rate, f, and the shear strain, y. A series of three standard strain-hardened states were obtained by prestraining specimens at 300°K and at a shear strain rate of 7.68 x lo-&apos; per sec to three stress levels of 6.89 X l08, 10.3 X lo8, and 14.5 x 10&apos; dynes per sq cm, respectively. Immediately following this prestrain the temperature bath was changed and each specimen was pulled in tension at either f = 7.68 X lo-&apos; or f = 3.06 X 10"3 per sec. In terms of the accuracy that was achieved, the values obtained did not deviate more than *0.1 X 10&apos; dynes per sq cm and * 1°K from the reported values of stress and temperature and not more than *5 pct in the reported values of the strain rate. The tensile stresses were converted to shear stresses using a factor of 1/2. The shear stress for the initiation of flow at the test temperature was determined by taking a y = 6.16 x 10&apos;3 offset. from the modulus line at which point good accuracy could be achieved in determining y and the associated flow stress 7, with only a negligible increase in the pre-

Jan 1, 1965

By E. V. Potter, E. T. Hayes, H. C. Lukens

LARGE volumes of hydrogen are liberated at the cathode during electrolytic precipitation of manganese. Most of the gas escapes from the electrolyte, but a considerable amount may be entrapped in the manganese plate. Gas has been observed to escape from manganese melts in puffs that ignite at the surface. It has been reported that castings made with electrolytic manganese tend to rise in the molds; for this reason the manganese is often treated to remove hydrogen before the melt is made or it is premelted and used as cast manganese in making the alloys. The effect of hydrogen on the properties of manganese and its alloys is not known, but its effect on iron and iron alloys has been studied extensively.1.2 The close relationship between iron and man¬ganese suggests that hydrogen may have a similar effect on the properties of manganese and its alloys. The purpose of this investigation was to determine the amount of hydrogen or other gases in typical commercial electrolytic manganese sheet and to investigate ways of removing it most conveniently. APPARATUS The apparatus used is shown schematically in Fig. I. It consists of a chamber A in which the metal sample is placed, a vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The specimen chamber was made of two concentric quartz tubes. The outer one, a, connects with the closed gas system and is surrounded by the furnace G. A second tube, b, fits closely inside a and has a small end that projects into the space for the specimen and holds the thermocouple for measuring the temperature of the sample. The inner tube is joined to the outer tube outside the furnace, with rubber tape and sealing wax, to prevent gas leakage into or out of the closed system. This type of specimen container is loaded very easily and can be used several times if molten metal does not come in contact with the quartz. An ordinary mercury manometer B is used to measure the pressure in the system. The volume gauge C is essentially another mercury manometer, but the volume of the column is much larger than normal and the height of the mercury can be varied by raising or lowering the well H. In this apparatus the tube had a volume of I00 c.c. for a 60-cm. length. For larger changes in gas volumes; auxiliary containers F were used to increase the volume of the system by known amounts. Valves were arranged so that these auxiliary containers could be filled from the system and evacuated by the pump as often as necessary to accommodate the increases in the volume of gas in the system. The furnace G, used to heat the samples, was equipped with an automatic temperature controller, which maintained the desired temperatures within ± 5°C.

Jan 1, 1945

By Irving Cadoff, Kurt Komarek, Edward Miller

Barium can be purified by equilibration with titanium. The melting point of barium was found to be 726.2° i 0.5 °C. The room-temperature lattice parameters of BaTe and Bask are 7.004 * 0.002A and 6.600 * 0.002A. Melting points for BaTe and Base were found to be 1510° * 30°C and 1830° ± 50°C, respectively. HIGH-purity barium and its compounds are difficult to prepare because of the reactivity of barium with the atmosphere and the large heats of formation of the compounds. Purification of barium by vacuum distillation,&apos; and the preparation and properties of barium oxide2 and barium sulfide3 have been reported. However, little has been done on the homologous compounds barium selenide and telluride. PURIFICATION OF BARIUM Distilled barium obtained from King Laboratories was used as the starting material. The analysis supplied with the metal showed the presence of: 0.4 wt pct Sr, 0.001 pct Mg, 0.02 pct F, 0.003 pct Cu, 0.005 pct Na and less than 5 x 10-3 wt pct of any other metallic impurity. Analyses for oxygen and nitrogen were not available. Since there is evidence4 that any barium nitride present in the starting material may decompose on distillation producing nitrogen which can contaminate the distillate, further purification was performed. At elevated temperatures, any nitrogen and oxygen present in barium should be removed by reaction with titanium. Assuming that the solubility of oxygen in liquid barium is negligible near the melting point of barium, any oxygen present will be in the form of BaO. Removal of oxygen from molten barium is expressed by the equation: BaO(S)+ TixOy(S) = Ba(l)+ TixO(y+1)(s) where Ti,Oy and TixO(y+1) are solid solutions of oxygen in titanium. At 1000°C, the change in free energy for this reaction is negative for (y+1)/x +y+1) x (100) 17.5 at. pct O.5 Since reaction with commercially pure titanium (containing 0.07 wt pct oxygen) results in a free energy change for the reaction of -19 kcal per g-atom, slight solubility of oxygen in barium would not hinder the oxygen removal. Since comparable thermodynamic data are not available to permit calculation of the partition of nitrogen between liquid barium and titanium, a similar quantitative relationship cannot be obtained. However, on the basis of work by Kubaschewski and Dench,5 complete removal of nitrogen from liquid barium can be expected. Since the melting point of barium is depressed markedly by small additions of nitrogen,&apos; the change in melting point during reaction of barium with titanium was used to follow the purification reaction. MELTING POINT OF BARIUM A 50-g sample of barium was sealed by arc welding under argon into an all titanium crucible provided with a thermocouple well. The melting point of the sample was determined by thermal analysis, using a Pt/Pt-10 pct Rh thermocouple which was calibrated according to National Bureau of Standards specification6. The crucible was then heated for 48 hr at 950°C in vacuum and the melting point redetermined. This procedure was repeated until three successive thermal analyses agreed within ±0.5oC, the limits of error of the analysis. The melting point increased from an initial value of 720.0°C to a final value of 726.2°C. Analysis on samples quenched from 950°C gave a solubility value of 0.004 wt. pct Ti. Assuming that the titanium-barium phase diagram is similar to those of titanium-magnesium7 and titanium-calcium,8 the solubility of titanium in liquid barium decreases with decreasing temperature. Therefore, the solubility of titanium in liquid barium should be less than 0.004 wt. pctat the melting point (726oC), and the effect of dissolved titanium on the melting point would be negligible. Addition of up to 3 wt pct Sr does not significantly change the melting point of barium,7 so that the effect of the 0.4 wt pct Sr in the starting material will also be negligible. The value of 726.2" ± 0.5C obtained for the melting point of barium can be compared .with a determination carried out by Keller and coworkers in low-carbon steel crucibles,&apos; who obtained a value of 725± 1C, using barium purified by fractional distillation. The higher value obtained in the present investigation is indicative of the effectiveness of titanium in removing traces of nitrogen. PREPARATION OF BaTe AND Base The compounds were prepared by direct reaction

Jan 1, 1961

By O. D. Sherby, J. E. Dorn, C. D. Wiseman

MCLEAN&apos; has shown that the total strain obtained during creep of aluminum polycrystals arises exclusively from the mechanisms of 1) microscopically observable slip, 2) subgrain tilting, and 3) grain boundary shearing. Extensive analyses, however, suggest that the high temperature creep of metal polycrystals is controlled by a single thermal activation process."" These somewhat contradictory observations might be reconciled if it could be shown that the activation energies are identical for each of the mechanisms isolated by McLean. Such identity of the activation energies, of course, would demand that the same unit process controls the functioning of each individual mechanism. Under these conditions the activation energies for creep of single metal crystals and polycrystalline aggregates and for grain boundary shearing should be identical. This paper is primarily concerned with the possible identity between the activation energies for high temperature creep of single crystal and polycrystalline metals. In addition, comparisons will also be made between the activation energies for creep of single crystals and polycrystals with previously reported activation energies for grain boundary shearing.0"8 Materials and Techniques The same high purity aluminum, lead, and tin were used in the creep tests for single crystals and polycrystalline aggregates. Single crystals of aluminum and tin were prepared by the strain-anneal technique, whereas lead single crystals were prepared by growth from the melt. The tensile creep stress was maintained constant by Chalmers-Andrade parabolic-type lever arms. Strains were measured to &0.0002 in. per in. with rack and pinion type extensometers, and temperatures were maintained to within & 0.2"C of the reported values by mercury-thermoregulated resistance-heated silicone oil baths. The previously reported unambiguous technique for determination of the activation energy for creep was employed throughout this investigation.&apos; ." It involves periodic abrupt small changes in temperature during the course of creep, accomplished by rapidly replacing one creep bath at temperature TI by a second bath at T,. The abrupt change in creep rate from i, to & attending the abrupt change in temperature is due exclusively to the change in temperature, since both the stress and the substructure are identical the instant before and the instant after a change of temperature. Therefore, all other factors being identical where AH is the activation energy for creep and R is the gas constant. Results Typical examples of the creep rate vs creep strain data during temperature cycled creep tests of single

Jan 1, 1958

WILLIAM L SAUNDERS, President GEORGE H PEGRAM, 1st Vice-president ALFRED D FLINN, Secretary J V W REYNDERS, 2d Vice-president JACOBS LANGTHORN, Treasurer HENRY A LARDNER Assistant treasurer Finance Committee House Committee GEORGE H PEGRAM, Chairman ; ALFRED D FLINN. Chairman J VIPOND DAVIES FREDERICK F SHARPLESS BANCROFT GHERARDI JOHN H DUNLAP WILLIAM L SAUNDERS CALVIN W RICE W F M GOSS, ex-officio F L HUTCHINSON

Jan 1, 1923

By Heribert Wiedemeier, Ali Khan

The tetnperature-conposition phase diagram of the syste,n MnS-CdS has been investigated over a range fro)n 600° to 1000° C. The small degree of solid solution on the MnS rich slde cornpared to the large CdS rich single-plzase region could be esplained by the difference in strzrctures of the cotnponents and the relative sizes of the metal ions. The change in lattice parameter as a function of cot)zposition is linear atzd jollous Vegavd&apos;s rule within experittzental limits of error. Mns and CdS have gained considerable attention in recent years because of their interesting solid state properties. In order to investigate such properties and thermodynamic quantities of mixed compositions of transition metal chalcogenides, it is necessary to establish their phase diagrams. Two earlier publications are concerned with the MnS-CdS system. Schnaase&apos; found complete miscibility when MnS and CdS were co-precipitated in aqueous solutions at room temperature. However, there is evidence that the mixed crystals were not stable over the entire range of composition. roger&apos;s&apos; investigation of the ternary system ZnS-CdS-MnS at 900" C indicates a solution of 48 mole pct MnS in CdS. During the course of this work which covers a temperature range from 600" to 100O° C, emphasis has been placed on the use of high-purity materials and well-defined modifications of starting products. EXPERIMENTAL Starting Materials. The stable green modification of MnS with NaCl structure was prepared by direct fusion of the elements and by chemical transport reaction. Stoichiometric amounts of manganese of 99.99+ pct purity and of sulfur of 99.999 pct purity from Gallard-Schlesinger Corp. were sealed in an evacuated quartz tube at a pressure of 10"5 mm Hg and annealed for 48 to 60 hr at 800°C. The quartz tubes used throughout this work were outgassed under high vacuum at a temperature of 90OU to 1000° C for 12 to 18 hr. For the synthesis of MnS by chemical transport3 stoichiometric ratios of elemental manganese and sulfur and small amounts of iodine were sealed under vacuum in a quartz tube, which was placed in the temperature gradient, 900/800-C, of a two zone furnace. Single crystals of MnS in form of platelets and octahedra were deposited at the cooler end of the tube. The manganese content was determined by EDTA titratin. A typical result of several analyses was 63.05 pct Mn which agreed well with the computed value, 63.14 pct. Commercially available CdS of 99.9+ pct purity, a mixture of the cubic and hexagonal forms, was converted into the hexagonal high-temperature modification by annealing CdS under vacuum in quartz tubes at 700° C for about 36 hr. As a second method, cadmium sulfide was transported in a temperature gradient, 70O° /650" C, with in vacuo sublimed iodine from the hot to the cooler zone of the tube. Large sized crystals in form of hexagonal columns and some platelets were obtained. An average result of the cadmium analysis by EDTA titration4 was 77.93 pct in good agreement with the computed value, 77.81 pct. Only the NaCl modification of MnS and the wurtzite modification of CdS were used for the solid solutions. Preparation of Solid Solutions. Finely powdered MnS and CdS samples were thoroughly mixed in molar ratios and compressed into pellets of about 6 mm diam and 2 mm in height at a pressure of approximately 13,500 atm.

Jan 1, 1969

By C. Hays, R. E. Swift, E. G. Kendall

Investigations of the Zr-Pt system, by metallography, incipient melting, and X-ray diffraction, determined the phase relationshifis from 0 to 50 at. pct Pt. Phase fields in the Pt-~ich region were outlined, and three intermetallics (ZrPt, Zr2Pt, and ZrPtd were located. A eutectic between Zr and Zr2Pt, and a eutectoid veaction between Zr and a Zr + Zr2Pt, were established. The maximum solubility of Pt in P Zr was approximately 13.5 wt pct, as opposed to less than 1 wt pct solubility in a Zr. EARLIER work on the Zr-Pt system was limited to an X-ray study on the intermetallic compound, ZrPt3, by H. J. Wallbaum,1 It was reported that ZrPt3 existed at 86.52 wt pct Pt, and had a hexagonal structure, isomorphous with TiNi3. Wallbaum&apos;s data revealed the following structural particulars: a = 5.633A, c = 9.21A, and c/a = 1.635A. Other studies allied to Zr-Pt alloys concerned only 1) Pt-rich alloys (0.05 to 5.0 pct Zr) for corrosion resistance,2 2) a Zr-base alloy with 5 pct Pt and 0.124 pct C for oxidation resistance,3 and 3) electroclad-ding of Zr with Pt for in-pile corrosion resistance of Zr to uranyl sulphate. 4 Metallographic, incipient melting, and X-ray diffraction techniques were applied to accurately resolve the phase relationships in the 0 to 50 at. pct (68.2 wt pct) Pt region, and to outline the phase fields in the Pt-rich area. Three intermediate phases: Zr2Pt, ZrPt, and ZrPt3, were also established by the same methods. PROCEDURE Melting stock for this program was of the highest purity obtainable. The Zr was iodide crystal bar with a low hafnium content of about 0.05 wt pct (Westinghouse "Grade 3"). The as-received Zr was treated to remove the surface film of corrosion product that resulted from a standard autoclave grade designation test. Next, the bars were processed to yield material suitable for arc melting and free of contaminants. Sheet platinum metal (Baker and Co. "Grade 2") was used for alloying additions. This material con-

Jan 1, 1962

By Heihachi Kamura

The reduction of iron oxide, such as Fe203, to iron in the blast furnace is performed principally by carbon monoxide, but partly by solid carbon by the two following reactions: Fe2O3 + 3CO = 2Fe 4- 3CO2 2Fe2O3 + 3C = 4Fe + 3CO2 It is known that reduction by carbon monoxide takes place at a much lower temperature than reduction by carbon and that the reducing action of earbon monoxide progresses to the inside of the ore in lump form by gaseous diffusion. In the reduction by carbon, however, the reducing action takes place only at the contact surface of the ore and carbon, so that the more complete the reduction by carbon monoxide, the more efficient is the operation. However, the reduction does not progress as shown in the foregoing equation, because carbon dioxide acts oxidizingly on the metallic iron to such a degree that when the gaseous composition reaches a certain proportion of carbon dioxide to carbon monoxide, the reduction practically stops, even though the gases are moving slowly through the heated ore. The proportions of carbon monoxide and carbon dioxide in the gas depend on the kind of iron oxide and the temperature of reduction, also on the duration of time in the reaction. The longer the time of the reaction, the higher the proportion of carbon dioxide obtained in the gas, but finally it will attain to a condition of equilibrium. Chemical Equilibrium of Iron, Oxygen, and Carbon Investigations concerning the equilibrium between iron, oxygen, and carbon have been carried out by E. Baur and A. Glaessner,1 who deter-

Jan 1, 1925

PRESIDENTS DAVID THOMAS 1871 Born November 3, 1794, Cadoxtan, Glamorganshire, South Wales. Died in 1882. Attended schools in Wales. Came to America in 1839. A.I.M.E.: Member, 1871; Honorary Member. Iron manufacturer; inventor. Built first anthracite fired hot-blast furnace in America. Known as the "Father of the Lehigh Valley." President, Catasauqua and Fogelsville Railroad; Director, Lehigh Valley Railroad; Founder, Thomas Iron Co. and St. Luke&apos;s Hospital at Bethlehem, Pa.; Trustee, Lafayette College.4 ROSSITER WORTHINGTON RAYMOND 1872-1874 Born April 27, 1840, Cincinnati, Ohio. Died in 1918. Brooklyn Polytechnic Institute, 1857; Lafayette College, Ph.D., 1868; Lehigh University, LL.D., 1906; University of Pittsburgh, Hon. LL.D., 1915., Gold Medal, Institution of Mining and Metallurgy (London). A.I.M.E.: Founder, Member of 1871; Vice President, 1871, 1876-1877; Secretary, 1884-1911; Secretary Emeritus, 1911-1918; Honorary Member. Consul¬ing mining engineer; practicing lawyer, sailor, soldier, writer, orator, editor, theologian, teacher, novelist, chess player. Recognized as the "Grand Old Man of the Institute." ALEXANDER LYMAN HOLI,EY 1875 Born July 20, 1832, Lakeville, Conn. Died in 1882. Brown University, 1853; Hon. LL.D., 1878. A.I.M.E.: Member, 1871; Vice President, 1874; Manager, 1877-1879. Bessemer Medal (Iron and Steel Institute, London), posthumously. Brought bessemer process to United States. A statue was erected in Washington Square in his memory and presented to the City of New York in 1889. The inscription notes: "foremost among those whose genius and energy established in America and improved throughout the world the manufacture of bessemer steel." ABRAM STEVENS HEWITT 1876 Born July 31, 1822, Haverstraw, N. Y. Died in 1903. Columbia University, 1842; Hon. LL.D., 1887. A.I.M.E.: Member, 1871; Manager, 1872-1875. Bessemer Medalist and Honorary Member, Iron and Steel Institute (London). Gold Medal, Chamber of Commerce of New York City. Philanthropist, lawyer, statesman, publicist, pioneer in the iron and steel industry. Mayor of New York City in 1887. Business partner of Peter Cooper, Executive Manager of Board of Trustees, Cooper Union, New York City.

Jan 1, 1947

By T. T. Field, M. Gell

MUCH has been learned about plastic deformation behavior in crystals through the use of dislocation and slip band etchants. Slip in nickel and nickel-base alloys has previously been revealed by various etching techniques.l-5 The techniques for nickel-base super-alloys4,5 were successful only in the Udimet 700 composition in specific heat-treated conditions. The objective of this work was to develop a more generally applicable slip-band etching procedure. The nominal compositions of the alloys used in this study are listed in Table I. The low carbon Mar-M2OO alloy referred to in the text is the same as listed in Table I with the exception that the carbon content is less than 100 ppm. Mar-M200 and Udimet 700 were solutionized at 2250" and 2150°F, respectively. The aging treatment for both cast alloys was 32 hr at 1600°F and for wrought Udimet 700 was 4 hr at 1975"F, 24 hr at 1550°F, and 16 hr at 1400°F. The new slip-band etching technique consists of a chemical etch followed by a short electropolish, Table 11. Fig. l(a) shows the best result obtained on an internal section of a plastically deformed single crystal of Mar-M2OO when using a conventional slip-band etching procedure which consists of electropolishing followed by etching. Ghostlike traces corresponding to planar slip bands are observed, but the contrast between the bands and the background is weak. Fig. l(b) shows the same field using the new slip-band etching technique. After the etching step of this technique, the same ghostlike traces of Fig. l(a) are observed, but the subsequent electropolishing accentuates the slip bands and the subgrain boundaries while the rest of the matrix is being polished. Longer electropolishing obliterates the slip bands. The new slip-band etching technique makes use of the etchants and electrolytes that are normally used for a given material. Because of this, it should be possible to slip-band etch other nickel-base superal-loys by using existing etchants and electrolytes for a material and following the procedures outlined in the "Comments" section of Table 11. All the illustrative examples given below show internal plastic deformation in single crystals of regular and low carbon Mar-M200 in the solutionized and

Jan 1, 1970

By R. F. Shurtz

R. Duval (Mining Engineer, Ancien eleve de PEcole Polytechnique, Paris, France) I do not agree with the Eq. 3, reading: m =1/100- [(0.214x30.4) + (0.7B6 x0.00)] =6.5pct CaO If 0.214 and0.786 were proportions by weight, the equation would represent the well known mixtures law of the conventional arithmetics and 6. 5 pct CaO would be the correct average content. But it is not the case as the author states: "In samples consisting of single grains of mineral, those grains must, as already mentioned, be either of dolomite or magnesite. Since 78.6 pct of the deposit consists of magnesite and 21.4 pct of dolomite (excluding for present purpose the presence of other minerals), for any single grains picked at random the probability will be 0.214 that is it dolomite and0.786 that is it magnesite. In 1000 such samples the expected numbers of dolomite and mapesite grains will be 214 and 786 respectively." 0.214 and 0.786 would be proportions by weigbt under the necessary condition that all grains of dole mite and magnesite should have an identical weight. Obviously it is not the case, as the specific gravities are not the same for mapesite and dolomite and the volumes of the grains are different. Furthermore, because of these differences the conditions for a random sampling are not fulfilled and we are not authorized to state that the probabilities are, respectively, 0.214 and 0.786. The author however makes a simple application of Eq. 1: M = 1/n— ? fi x i . n Should we deduce that this relation is wrohg? Not at all, but when applying Eq. 1 you must not overlook what it actually. means. Eq. 1 gives a definition of the arithmetic mean of a total of n observed values Xi and nothing else. But the average conteht of a deposit has not the same significance. It is the ratio between the weight of concerned mineral in the deposit and the total weight of the deposit. As from 1000 particles the 214 of dolomite and the 786 of magnesite have not the same weight, the two definitions do not concur, and when applying Eq. 1 the result is an arithmetic mean of figures which has no connection with what is named average contentof a deposit. The situation is similar to the calculation of an average velocity. If a car travels a first mile over at 30 miles per hr and a second mile over at 60 miles per hr, when applying formula 1 you find as average velocity for the 2 miles: 30+60 ------- - 45 miles per hour. Many people calculate in this way and they do not realize that a mistake is involved. In fact the definition of he average velocity for the 2 miles is the quotient of the distance of 2 miles by the time (in hours) necessary for 2 miles travel, i.e.: 2 ---------- = 40 miles per hr. 1 + 1 30 60 In other words, the average volocity wanted is not the arithmetic but the harmonic average of the two velocities. The above mentioned bias in the calculation of the average contents of deposits is frequent, even in the assessments made by experienced engineers and is independant of what is named the sampling error. In order to supress the bias and to be able to use Eq. 1, you must apply a correction. An example on the subject can be found in an article by Duval et al. in the January 1955 issue of the &apos;&apos;Annales des Mines" (French), page 19. R. F. Schurtz (Author&apos;s Reply) Mr. Duval&apos;s position is quite correct. The proportions shown for dolomite and magnesite., respectively, of 0.214 and 0.786 are, in fact, proportions by weight uncorrected for specific gravity. In our day to day operation of producing magnesite from these mines at a very substantial rate, we do not normally make corrections for the difference between the specific gravity of dolomite and that of magnesite. If these corrections are made in Eq. 3 as shown in my article, then the numbers of grains turn out to be in proportions of 0.226 dolomite and 0.774 mapesite instead of the values actually shown in the equation. For the purposes of our work, and in view of the inherently low accuracy of the data, this correction was not deemed worthwhile making.

Jan 1, 1961

By J. H. Kittel

THE properties of the metal molybdenum have been the subject of recent investigations1,2 = which have included studies of the changes that occur in the metal when it is annealed after having been cold worked. Most of the data which have been reported have pertained to only one aspect of annealing, that is, the conditions under which recrys-tallization has been observecl. The process of recovery which may precede recrystallization docs not appear to have been investigated, and it is the purpose of this note to report observations on the recovery process in cold-worked molybdenum as determined by changes ill the thermoelectric power which occur as the metal is annealed. The measurements were made on commercially pure molybdenum wires which, after annealing at 1035°C in dried hydrogen for 1 hr, were swaged to give a series of reductions up to a maximum of 84.5 pct. The variously cold-worked wires were then annea1c.d in dried hydrogen for periods of 16 hr at progrc:ssively highel. temperatures from 200" to 1000 c with a final annealing treatment of 70 hr at. 1100°C. After each annealing treatment the ther.ma1 emf&apos;s were determined against a length of original unwo~,ked material that had received the initial hydrogen anrit,aling treatment. The difference in temperature between the hot and cold junctions was maintained at about 75&apos;C. and. the thermal emf&apos;s were measured with a potentiometer that could be read. to 0.01 microvolt. Fig. 1 shows the thermoelectric power. (dE/dT) in microvolts per C between annclalcd and cold-worked molybdenum as a function of the degree of cold work. The effect of annealing is shown in Fig. 2. The general shape of the curves in both figures is similar to results which have been obtained for copper." It was observed that after annealing at temperatures as low as 200°C recovery was well under way. The rapid changes irt thermoelectric power observed near 900 C are probably associated with recrystallization, since such a relation has been observed with copper. Beyond 900°C the thermal emf&apos;s changed in polarity. indicating that from this point or1 the specimens were more highly annealed than the standard. Annealing treatments could not be given at temperatures higher than 1100°C due to limitations of the furnace, and it is evident that, since equilibrium values of thermoelectric powers were far from having been attained, temperatures considerably higher are required to fully anneal molybdenum. References Robert M. Parke: Molybdenum, A New High-Temperature Material. Metal Progress (1951) 60, pp. 81-96. * R. A. Long, K. C. Dike, and H. R. Bear: Some Properties of High-Purity Sintered Wrought Molybdenum Metal at Temperatures up to 2400 °F. NACA TN 2319 (March 1951): G. W. Brindley: A Thern-io-Electric Study of the Cold-Rolling and Heat-Treatment of Copper, Report of a Conference on the Strength of Solids. Physical Society, London (1948) pp. 95-106.

Jan 1, 1953

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 28 Montreal, Canada Sept, ?79 8 29 New York, N.Y. Feb, ?80 9

Jan 1, 1923

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION TO OCTOBER, 1904 Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8

Jan 1, 1923

By AIME AIME

OUT of the fabulous iron ranges of Michigan?s Upper Peninsula since Pearl Harbor have come go to the steel mills to become tanks, guns, ships, and other weapons for a United Nations&apos; victory. But the contributions to the war effort, as far as Michigan&apos;s iron country is concerned, do not stop there. The same men who mine iron ore deep inside the earth also are "mining" on top of the ground, gleaning a harvest of scrap iron and steel that is writing a big chapter in the War Production Board&apos;s salvage program. At virtually every mine over an area of a hundred square miles, everyone from the top mine official and straw boss to the man in the dippings is scrap conscious. They know the importance of the ore they mine but they are equally familiar with the importance of iron and steel scrap in war production. The successful job they are doing in salvage is a tribute to the entire Upper Michigan mining industry and to the man who marshaled them into action-John M. Bush, chief of the land department for the Cleveland- Cliffs Iron Co. at Negaunee, and for ten years an A.I.M.E. member. Also, this job should be an inspiration to 611 mining. metallurgical, and petroleum communities as to the latent possibilities of organized scrap recovery.

Jan 1, 1943

By David K. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are w-asted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Shipments of pyrite from coal mines during 1941 were reported as follows: Illinois -The Midland Electric Coal Corp., Henry County, shipped 12,026 long tons containing 46 pct sulphur, at its Atkinson preparation plant. Indiana—The Snow Hill Coal Corp. produced pyrite from its Talleydalc preparation plant in Vigo County. Kansas—The Mineral Products Co. produced 3902 long tons of pyrite containing 44 pct of sulphur from picking table and washery refuse. Specifications for coal pyrite for acid manufacture rangc from 5 to 8 pct maximum carhon limit, and 42 to 45 pct minimum sulphur limit. Where flash roasting is practiced, the pyrite must be minus 100-mesh. Most companies give no size specifications. One company specifies 20- mesh or finer. Impurities in pyrite other than carbon may limit its use—for instance, arsenic, probably as arseno pyrite-—even though a concentrate can be made complying with specifications otherwise. Pyrite-recovery Plants Bradford breakers and picking tables may be used to make a marketable product where the pyrite occurs largely in sizes coarser than about I in. To make a grade of concentrate acceptable to sulphuric-acid plants the pyrite must break freely from the accompanying coal and slate, which is a rare condition to find. Most pyrite occurring in coal beds requires crushing and an abrasive type of grinding to free it of entwined coal and slate, followed by mechanical concentration by jigs, tables or other concentrating devices suitable for heavy ores, to make a satisfactory concentrate. At the Snow Hill Coal Corporation&apos;s plant in Indiana and at the Midland Electric Corporation&apos;s plant at Xtkinson, Ill., the final concentrate is made by a mechanical jig. The most recent and complete mill for concentrating pyritc from coal-mine refuse is that of the Mineral Products Co. at West Mineral, Kans., in which jigs and tables are used. Many regrinds and recirculations of products are necessary to get a concentrate of uniform grade. Trends On the whole, the economics of recovering pyritc from coal is not favorable. Cer-

Jan 1, 1948

By David K. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are w-asted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Shipments of pyrite from coal mines during 1941 were reported as follows: Illinois -The Midland Electric Coal Corp., Henry County, shipped 12,026 long tons containing 46 pct sulphur, at its Atkinson preparation plant. Indiana—The Snow Hill Coal Corp. produced pyrite from its Talleydalc preparation plant in Vigo County. Kansas—The Mineral Products Co. produced 3902 long tons of pyrite containing 44 pct of sulphur from picking table and washery refuse. Specifications for coal pyrite for acid manufacture rangc from 5 to 8 pct maximum carhon limit, and 42 to 45 pct minimum sulphur limit. Where flash roasting is practiced, the pyrite must be minus 100-mesh. Most companies give no size specifications. One company specifies 20- mesh or finer. Impurities in pyrite other than carbon may limit its use—for instance, arsenic, probably as arseno pyrite-—even though a concentrate can be made complying with specifications otherwise. Pyrite-recovery Plants Bradford breakers and picking tables may be used to make a marketable product where the pyrite occurs largely in sizes coarser than about I in. To make a grade of concentrate acceptable to sulphuric-acid plants the pyrite must break freely from the accompanying coal and slate, which is a rare condition to find. Most pyrite occurring in coal beds requires crushing and an abrasive type of grinding to free it of entwined coal and slate, followed by mechanical concentration by jigs, tables or other concentrating devices suitable for heavy ores, to make a satisfactory concentrate. At the Snow Hill Coal Corporation&apos;s plant in Indiana and at the Midland Electric Corporation&apos;s plant at Xtkinson, Ill., the final concentrate is made by a mechanical jig. The most recent and complete mill for concentrating pyritc from coal-mine refuse is that of the Mineral Products Co. at West Mineral, Kans., in which jigs and tables are used. Many regrinds and recirculations of products are necessary to get a concentrate of uniform grade. Trends On the whole, the economics of recovering pyritc from coal is not favorable. Cer-

Jan 1, 1948