Search Documents

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By Richard W. Lodge

Mr. H. R. Batcheller, of the class of 1894, Massachusetts Institute of Technology, while experimenting with chlorine gas on a certain lot of roasted concentrates, met with the following difficulties: 1. A poor extraction of the gold. 2. A very large consumption of chlorine gas. 3. Inability to precipitate all of the gold from the solutioil containing the AuC1,. 4. The bullion obtained was very base. These difficulties were the same whether the chlorine was generated from H2SO47 MnO29 and salt, or whether H2SO, and bleaching powder were used. They may be accounted for partly by the presence of some arsenic left in the roasted ore, and partly by the presence of copper in the solution containing the AuCI3. It was therefore suggested to try the effect of bromine on a similar lot of ore. The use of this element is, of course, nothing new, but in the following experiments it seemed to present many advantages over chlorine. The material worked upon consisted of some concentrates containing 2.31 ounces of gold per ton, and 34.26 per cent. of arsenic, which would correspoild to about 74.4 per cent. Of

Jan 1, 1896

By Robert Sisselman

Dramatic changes have been effected since 1955 in the mode of iron ore shipments within the U.S. In 1955, less than one percent of ore consumed in domestic blast furnaces-approximately 125 million long tons-consisted of pellets. Five years later, in 1960, some 94.8 million tons of ore were consumed, 14% in the form of pellets. Projections for 1980 reinforce confidence in this most economic of blast furnace feeds, and set U.S. pellet consumption at 151.2 million tons. In the last decade, pellets caught fire in other countries. By 1969, world production reached 96 million tons. This compares strikingly with present world output of 154 million tons.

Jan 9, 1973

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at subcritical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.1 Westgren, Phragmén and Negresco2 identified the following carbides in chromium steels: [Cementite Fe3C (containing up to about 15 per cent Cr) Trigonal carbide Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide Cr4C (or Cr23C3) (containing up to about 25 per cent Fe) Orthorhombic carbide . Cr3C2 (containing only a few per cent Fe)] The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus.4 By means of dilatometric and microscopic studies, sections of the diagram were established. This diagram showed the presence of the special carbide Cr7Ca in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in r per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7Ca occurs in chromium steels containing more than about 1 per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. EXPERIMENTAL PROCEDURE The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into 1-in. round bars, and all heat-treatments were conducted on specimens of this section .size. Sections of the bar stock 8 in. long were hardened in air, oil or water depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after auenchine. The quenched bars were cut into

Jan 1, 1942

By H. R. Deeth, C. J. Koenig

About ten years ago nepheline syenite was introduced to the ceramic industry and the material has now found application in the various branches of the industry, namely, as a vitrifying agent in white-wares and as a source of alumina and alkalies in glasses, glazes, and porcelain enamels. Spencel described the early mining and processing developments regarding this material. Since the time of his article many research papers have appeared relating to the usage of nepheline syenite but little has been published relative to subsequent mining and processing methods. A complete indexed review of the literature was issued recently by Ohio State University.2 Since "Lakefield" nepheline syenite from Blue Mountain, Ontario (Fig I); is the only commercial ceramic-grade nepheline syenite now being marketed on this continent, discussion is limited to this operation carried on by American Nepheline Limited, Lakefield, Ont., and its subsidiary in the United States, American Nepheline Cory. at Rochester, N. Y. The Deposit Blue Mountain is a long ridge rising to an elevation of about 350 ft at its highest point above the surrounding country and extending for about six miles in a northeasterly direction across Methuen township, Peterborough County. The rock of the Blue Mountain central alkaline intrusive is fine grained, light colored and of even granitic texture. The solidified mass consists predominately of the minerals albite, nepheline and microcline in order of abundance. The average mineralogical composition for the deposit obtained by a study of 112 samples taken regularly over the whole formation is as follows:3 Volumetric Mineral Per Cent Albite.................... 54 Microcline................ 20 Nepheline................ 22 Muscovite................ 2 Mafics.................... 2 (Biotite, hastingsite, magnetite) Total................... loo The mineral nepheline (or nephelite) belongs to the feldspathoid group but is lower in silica content than are the feldspars. It is a silicate of soda, potash, and alumina (NaKAl2O32SiO2). Its presence with albite (Na2oA12O3 6SiO2) and microcline (K2O A12O3 6SiO2) gives the Blue Mountain deposit an alkali content of 15 pct and an alumina content of approximately 24 pct. While this huge alkaline mass is somewhat variable mineralogically, it has a uniform chemical composition. When the iron, mostly in the form of magnetite, is removed during processing, a remarkably uniform finished product is obtained. Geological surveying has disclosed many million tons of nepheline syenite in the Blue Mountain deposit. Diamond drilling in the area where mining is now being carried out indicates a block of about one million tons.

Jan 1, 1949

By V. Vahatalo, E. Hakapaa, H. Tanner

Recently modernized, the surface plant of the Outokumpu mine in Finland incorporates a number of ideas meriting close scrutiny from this side of the Atlantic. The mining methods make extensive use of concrete in some unusual ways. Design of the headframe and surface plant represents the latest thinking of European engineers and includes an integral Koepe hoist. The deposit is in eastern Finland, province of North Karelia, 30 miles west northwest of Joensuu and at 60'44' N, latitude. Pyrrhotite, pyrite, chalcopyrite, and sphalerite mineralization occurs in a shear zone in quartzite near a body of serpentinite. Two lenses have a total length over 12.000 ft, with remaining reserves of the 3 to 4 pct Cu ore estimated at about 15 million metric tons.

Jul 1, 1955

By Knut L. Sandvik, Aage Solbakken

it is an established fact that the collecting properties of xanthates and anionic collectors are dependent on the hydrocarbon chain length. This is ascribed to the greater adsorption densities caused by increasing the xanthate chain length. As batch flotation tests showed similar trends for amines, an investigation of the adsorbing properties of amines was undertaken. Because earlier investigations showed adsorption densities for dodecylamine salts on quartz varying as much as 20 times under apparently similar conditions,1-4 it was decided to make a survey of the changes in adsorption density due to the drying conditions of the quartz. EXPERIMENTAL PROCEDURE The quartz, handpicked in the pegmatite quarries of Iveland, Setesdal, had the following composition: SiO2 99.81, A12O3 0.01, Fe2O3 0.05 and loss by ig-

Jan 1, 1969

By M. Gensamer

ONLY recently has it been realized that preferred orientations are common in hot-rolled steels. In a recent paper, N. P. Goss1 stated that hot-rolled mild steel exhibits a texture different from that charac-teristic of cold-rolled steel. No complete study of these hot-rolling textures has been reported using the pole-figure method of Wever. The material used in the work reported in this paper was the same material used by Gensamer and Mehl2 in a recent study of preferred orientations in cold-rolled steel, to which reference may be made for the composition and thermal history of the steel. Automobile-body sheet bar, 4 in. thick was hot-rolled at two temperatures, 780° and 910° C. (1436° and 1669° F.). (These temperatures refer to the tempera-ture of the furnace in which the steel was heated.) After each pass the steel was returned to the furnace and held there long enough to return to temperature. Although no accurate method was used to measure the temperature after each pass, it was estimated by color that only a slight drop in temperature occurred. In order to determine the effect of any preferred orientation that might have persisted through the normalizing treatment, one specimen at each temperature was rolled in the same direction as the original working direction and the other at right angles to it. The total reduction in each case was 85 per cent, the specimens having been reduced from 0.250 to 0.0375 in. in five passes. Final cooling was in air. Pinhole reflection photograms were taken of all four specimens, with the rolling direction vertical and the X-ray beam at an angle of 7° with the transverse direction (the transverse direction is defined as that direction in the rolling plane perpendicular to the rolling direction). These photograms, taken with a Me target at 35 kv., are reproduced in Figs. 1, 2, 3 and 4. They show that a more pronounced texture was developed by the low-temperature rolling (780° C.), and that of the two

Jan 1, 1936

By K. R. Price, M. Gauna

A high seam geologic condition exists at Jim Walter Resources No. 4 mine that requires immediate rib support after a continuous miner cuts a place. High seam mining heights are typically 2.4 to 2.6 m (8 to 9 ft) and a thick rock layer is present in the upper portion of the coal rib side. The 610-m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 305 mm (12 in.) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas that endanger men and equipment. To control this, rib support must be installed in the roof bolting operation as the bolting crew works toward the face. A rib control system has been developed for this high seam mining condition using a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDM-15 bolting machine. More than 120 km (75 miles) of entry have been supported with angle rib bolts. These angle bolts constitute 43% to 60% of the total roof and rib bolt footage in the high seam portions of No. 4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method using bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people. Total drilling supply costs are about 60% the previous cost, when compared to the previous support method using horizontal rib bolts:

Jan 1, 1985

By Charles Fulton

EXPERIMENTAL work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such, a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc lead ores, since the residue from the distillation is held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet

Jan 9, 1919

By A. S. Richardson

THe conditions that make necessary the mechanical ventilation of the Butte mines of the Anaconda Copper Mining Go. are due to a number of causes, all of which are incidental to the depth at which mining operations are now carried on, The main object to be accomplished, of course, is the reduction of the temperature and humidity of the air in the working places. Ventilation fans, both surface and underground, have been used for many years, but increasing depth has made the problem much more difficult. Further improvement in both ventilation equipment and methods, therefore, became necessary; and it is the purpose of this paper to describe the work planned and done under the improvement program. The mines of the district have been frequently described in various technical publications, so a description is unnecessary here. From a mine-ventilation viewpoint, compared with coal-mine ventilation systems, the problem is complicated by the fact that the workings to be ventilated are situated on a large number of steeply dipping veins which frequently intersect and are faulted, and also by the fact that the extent, or existence, of orebodies is not definitely known in advance of actual development work. For these reasons ventilation work cannot be planned in advance of actual operations, nor can such regular systems of ventilation as are used in working the more uniform and continuous bodies of coal be developed. When operations are conducted at a normal rate, about 10,000 miners are employed on two shifts, so that about 5000 men will be underground at one time. But as ventilation is necessary to reduce high temperature and humidity due, mainly, to natural causes, the quantity of air per man per minute is not a governing consideration in determining ventilation requirements. Most important among the numerous sources of heat and humidity in the mines are: heat generated during decay of mine timber; heat and humidity given off by mine rock and water; heat generated by oxidation of sulfide minerals; heat given off by electrical equipment; heat generated by mine fires (in certain localities).

Jan 1, 1923

By A. S. Richardson

THe conditions that make necessary the mechanical ventilation of the Butte mines of the Anaconda Copper Mining Go. are due to a number of causes, all of which are incidental to the depth at which mining operations are now carried on, The main object to be accomplished, of course, is the reduction of the temperature and humidity of the air in the working places. Ventilation fans, both surface and underground, have been used for many years, but increasing depth has made the problem much more difficult. Further improvement in both ventilation equipment and methods, therefore, became necessary; and it is the purpose of this paper to describe the work planned and done under the improvement program. The mines of the district have been frequently described in various technical publications, so a description is unnecessary here. From a mine-ventilation viewpoint, compared with coal-mine ventilation systems, the problem is complicated by the fact that the workings to be ventilated are situated on a large number of steeply dipping veins which frequently intersect and are faulted, and also by the fact that the extent, or existence, of orebodies is not definitely known in advance of actual development work. For these reasons ventilation work cannot be planned in advance of actual operations, nor can such regular systems of ventilation as are used in working the more uniform and continuous bodies of coal be developed. When operations are conducted at a normal rate, about 10,000 miners are employed on two shifts, so that about 5000 men will be underground at one time. But as ventilation is necessary to reduce high temperature and humidity due, mainly, to natural causes, the quantity of air per man per minute is not a governing consideration in determining ventilation requirements. Most important among the numerous sources of heat and humidity in the mines are: heat generated during decay of mine timber; heat and humidity given off by mine rock and water; heat generated by oxidation of sulfide minerals; heat given off by electrical equipment; heat generated by mine fires (in certain localities).

Jan 1, 1923

By R. W. Heckel, H. P. Cheskis, A. Lawley, M. R. Pinnel

THERE are discrepancies reported in the literature regarding the micro and macro stress-strain behavior of metals and alloys. In particular, Young's modulus and micro yield measurements often show significant variations depending upon the techniques employed.'-" The purpose of this note is to correlate measurements made with four techniques and to indicate where some of these discrepancies might arise. Allied use of these techniques can provide a complete and consistent characterization of micro and macro stress-strain behavior (over the strain range of 10-9 to 10--2 in. in.-') from a minimum number of samples. Techniques. The techniques employed for measuring stress-strain behavior involved the use of a) linear differential transformers, b) SR-4 strain gages, c) longitudinal resonance waves, and d) X-ray diffraction. Specimen geometries and preparations are summarized in Table I for each technique. Differential Transformer and Strain Measurements. An Instron universal testing machine, modified with an alignment device, was used to apply the load via parallel-jaw grips. The signal from the load cell was applied to the Y scale of a Moseley X-Y recorder (sensitivity of 10 lb load per in. chart). The elongation was monitored simultaneously with strain gages mounted on three sides of the rectangular specimen, and with two linear variable differential transformers (LVDT) mounted at 90 deg to one another on faces that also contained the strain gages, Fig. 1. The signal from one of the LVDT's was applied to the X scale of the recorder (sensitivity 40 µ in. elongation per in. chart) in order to trace a continuous load-elonga-tion curve. Concurrently, the strain on the same face (i.e., the face monitored by the LVDT) was recorded by the corresponding strain gage. A stress-strain curve was plotted from the load cell-strain gage data and was compared to the stress-strain curve (converted from load-elongation) plotted from the continuous load cell-LVDT trace. Identical Table I. Description of Specimens Used in the Present Study Material Dimerisions Preparation Condition 99.99 pct A1 tensile 318 by 3/16 by 3 in. as cast ingot; cut annealed specimen on diamond wheel 2024 A1 tensile 318 by 3/20 by 31/2 in. vacuum hot annealed specimen pressed sheets; cut on diamond wheel 99.99 pct Al 3116 by 3/16 by 2 in. cut from tensile prestrained dynamic modulus specimen after 10"* in. specimen test per in. 2024 A1 dynamic 3/20 by 3/20 by 2 in. vacuum hot annealed modulus specimen pressed sheets; cut on diamond wheel 2024 A1 X-ray gage section 112 by vacuum hot annealed specimens 1/4by1/20in. pressed sheets; cut on diamond wheel

Jan 1, 1970

By W. H. Echols

An oil-emulsion mud, consisting of a mixture of oil-base mud and bentonitic water-base mud, has been used experimentally in drilling 8 of the 35 wells in the Sivells Bend field, Cooke County, Texas. Experience indicates the oil-emulsion mud can be controlled in much the same manner as a water-base mud, and the "drilling" functions of the two types of mud are comparable. The average water-loss for the oil-emulsion mud was 3.8 cu cm per well. When using oil-emulsion mud to drill the last 2000 ft of 7000 ft wells, the mud costs were approximately 2½ times that of water-base mud. There is nothing to indicate well productivities have been affected through the use of oil-emulsion mud. However, drilling time and bit footages were increased and the holes were maintained more closely to bit guage. The apparent advantages gained through the use of oil-emulsion mud in the Sivells Bend field do not appear to justify the increase in mud costs. Introduction until a comparatively few years ago most of the development of drilling mud was directed toward improving the functions of the mud as related to actual drilling operations. The industry has long recognized that one disadvantage of rotary drilling over cable-tool drilling is the possibility of injury to producing zones through the blocking effect resulting from the infiltration of water or mud into the sands. Recognizing this disadvantage, considerable attention has been diverted toward the development of muds that will improve the quality of well com-pletions through the reduction or elimination of water into the sands, but without sacrificing too many of their "drilling" functions and at a cost commensurate with the benefits derived from their use. This phase of mud research has already found practical application, for example, in the development of the Rangely field, Colorado, it appears the use of oil-base mud during drilling-in operations will contribute appreciably toward making this exploitation more profitable. Much of the discussion to follow will be better understood if a brief sketch of the Sivells Bend field is given. The Sivells Bend field, discovered by The Texas Co. in 1944 and still in the process of development, is in a large bend on the Texas side of the Red River about 85 miles north of Dallas. Geologically, the structure is an unsymmetrical anticline, with faulting having contributed to its development. The productive sands are of the Strawn series of Pennsylvanian age, the sands being lenticular in character and varying considerably in development from well to well. At Present there are 35 producing wells in the field, producing from seven different sand lenses. The productive sand lenses vary from 15 to 50 ft in thickness and the individual sands have average permeabilities of from 75 to 375 md. The presently productive sands are encountered at depths of from 6300 to 7300 ft, but testing has indicated that commercial production might be obtained from other sands as high as 5200 ft. Histories of older Strawn

Jan 1, 1948

By W. H. Echols

An oil-emulsion mud, consisting of a mixture of oil-base mud and bentonitic water-base mud, has been used experimentally in drilling 8 of the 35 wells in the Sivells Bend field, Cooke County, Texas. Experience indicates the oil-emulsion mud can be controlled in much the same manner as a water-base mud, and the "drilling" functions of the two types of mud are comparable. The average water-loss for the oil-emulsion mud was 3.8 cu cm per well. When using oil-emulsion mud to drill the last 2000 ft of 7000 ft wells, the mud costs were approximately 2½ times that of water-base mud. There is nothing to indicate well productivities have been affected through the use of oil-emulsion mud. However, drilling time and bit footages were increased and the holes were maintained more closely to bit guage. The apparent advantages gained through the use of oil-emulsion mud in the Sivells Bend field do not appear to justify the increase in mud costs. Introduction until a comparatively few years ago most of the development of drilling mud was directed toward improving the functions of the mud as related to actual drilling operations. The industry has long recognized that one disadvantage of rotary drilling over cable-tool drilling is the possibility of injury to producing zones through the blocking effect resulting from the infiltration of water or mud into the sands. Recognizing this disadvantage, considerable attention has been diverted toward the development of muds that will improve the quality of well com-pletions through the reduction or elimination of water into the sands, but without sacrificing too many of their "drilling" functions and at a cost commensurate with the benefits derived from their use. This phase of mud research has already found practical application, for example, in the development of the Rangely field, Colorado, it appears the use of oil-base mud during drilling-in operations will contribute appreciably toward making this exploitation more profitable. Much of the discussion to follow will be better understood if a brief sketch of the Sivells Bend field is given. The Sivells Bend field, discovered by The Texas Co. in 1944 and still in the process of development, is in a large bend on the Texas side of the Red River about 85 miles north of Dallas. Geologically, the structure is an unsymmetrical anticline, with faulting having contributed to its development. The productive sands are of the Strawn series of Pennsylvanian age, the sands being lenticular in character and varying considerably in development from well to well. At Present there are 35 producing wells in the field, producing from seven different sand lenses. The productive sand lenses vary from 15 to 50 ft in thickness and the individual sands have average permeabilities of from 75 to 375 md. The presently productive sands are encountered at depths of from 6300 to 7300 ft, but testing has indicated that commercial production might be obtained from other sands as high as 5200 ft. Histories of older Strawn

Jan 1, 1948

By B. B. A. Luzzat

ALUMINUM is today the most widely used of the nonferrous metals. The technical literature on the aluminum smelting process is, nevertheless, very meager, so that anyone interested in the subject cannot rely on more than a couple of dozen publications.' The patent literature is equally scarce; most patents refer to the production of alumina from aluminum-bearing ores, while not more than a few score significant patents deal with the electrolytic reduction of alumina, which is the real core of the aluminum smelting industry. The "reduction phase" is, from a technical and a scientific point of view, much more interesting than the "alumina phase", which, in effect, is only a combination of such well-known chemical operations as dissolving, precipitating, filtering, drying, and calcining. The electrolytic reduction of alumina, on the other hand, has features which do not appear in any other metal smelting operation. Some of them are of great technical and scientific interest even for those not directly engaged in the production of aluminum. The purpose of this paper is to describe in some detail the basic facts and developments of the reduction phase of aluminum smelting. Two Aspects of the Electrolytic Process The raw material for the reduction process is alumina (Al2O3) . Its purity in general runs as high as 99.50 pct or more. Small differences in the chemical composition generally do not affect the reduction process.* Of more importance are the physical prop- erties of the alumina, since they affect not only its rate of solution in the molten bath but also its heat insulating power.† In the following pages, un- less otherwise stated, it is assumed that a standard "Bayer" alumina is used. The reduction process, by which alumina is broken down into its components, may be roughly defined as its electrolysis in molten cryolite. The oxygen separates at the anode, and the aluminum at the cathode, which forms the bottom of the electrolytic cell. The electrolytic cell (or pot) where the process is carried out is a strongly reinforced steel box. The

Jan 1, 1951

Executive JOHN M LOVEJOY, Chairman ERLE V DAVELER G B WATERHOUBE WILBER JUDSON WILLIAM WRAITH J V W REYNDERS, Consultant Finance HENRY KRUMB, Chairman PAUL D MERICA R M ROOSEVELT H G MOULTON, Consultant Admissions RALPH M ROOSEVELT, Chairman GEORGE D BARRON, Vice-chairman JOHN L CHRISTIE PHILIP KRAFT W A SINSHEIMER

Jan 1, 1937

By AIME AIME

DATA in this report enable comparisons to be made within the bituminous coal industry and comparison as well with copper and steel in respect to capacity and overdevelopment. The conclusions reached from the data will tend to correct numerous current misconceptions. The data have been prepared by various members of the Coal and Coke Committee of the A.I.M.E., from the most authentic sources avail¬able, and cover the period 1913-1924 wherever possible. CAPACITY AND OVERDEVELOPMENT Table 1 shows statistics for the industry, mainly from the U. S. Geological Survey sources, but partly from the U. S. Coal Commission reports. The mine capacity with equipment and labor as of given date is calculated for each state by obtaining the total man days worked as reported by the operators, and dividing this figure into the total production, getting the production per man day; this figure times the number of men employed times 308 (a theoretical full working year) equals estimated full-time capacity. Two major objections are made to this method-one that the total number of men employed is used instead of the number actually working, and the other that the number of days used only deducts Sundays and five holidays. Covering the first, the same number of men is used in estimating capacity as is used in actual production, and this condition exists at all times. Regarding the second, the opinion is general among coal men that 280 days is as great a figure as should be used, as it is practically impossible to keep any mine working full time at the same daily rate as when it is working part time. The capacity, as estimated on this basis, is much more nearly the true capacity, although even with present railroad efficiency this amount of coal could not be moved.

Jan 1, 1926

By S. G. Dixit, A. K. Biswas

The flotation and adsorption behavior of ilmenite, monazite and zircon have been studied with sodium oleate as the collector and pH as the principal variable. The maxima in the flotation and adsorption properties of any of the above minerals fall within similar pH ranges. The bell shaped pH versus adsorption magnitude (r) curve is explained on the basis of collector concentration (Co and the concentration of hydroxyl ion (COH-) acting as the depressant. An equation of the type: 1 =KiCor~K2 Coh-/Coi-is proposed to account for the experimental data. The beach sand deposits along the sea coast in Southern India contain ilmenite, monazite, zircon, rutile and sillimanite as valuable minerals while quartz, garnet, shells and traces of hornblende form the gangue. A typical composition of the deposits is reported to be as follows:' Ilmenite 75%, Zircon 4-6%, Rutile 3-4%, Monazite 2 - 4%, Garnet 2 - 5% and the rest 8 -10%. Selective flotation of beach sand constituents has been reported by many workers.2-4 The fatty acid soaps have been invariably used as collectors. It is seen that all the valuable constituents of the beach sand are efficiently floated by soap collectors such as sodium oleate. In order to selectively float the beach sand constituents, it is necessary to use some depressants such as sodium silicate.3 The physicochemical parameters that govern the flotation of these minerals are yet to be studied in detail. In the present article, the findings on the parallel studies on the flotation and adsorption of the systems — ilmenite-sodium oleate, monazite-sodium oleate and zircon-sodium oleate — are being reported. In these correlative studies on adsorption and flotation of beach sand minerals, ilmenite (FeTiO3), monazite (Ce, Dy, Nd) PO4 and zircon (ZrSiO,) have been selected because they represent three important

Jan 1, 1970