Search Documents

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen' and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen' and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By M. D. Cooper

For the purpose of obtaining some first-hand data in regard to the shooting down of coal in bituminous mines, it was the writer's good fortune to be employed as a shot-firer for almost one year. In all, 6020 shots were fired by him during this period. All of the work was done in what is known as the South Main section of the No. 2 Mine of the Ellsworth Collieries Co., Ellsworth, Pa., a subsidiary of the Lackawanna Steel Go. Position of Shot-firing in the Cycle of Operations The established practice of the Ellsworth Collieries Co. calls first for the undercutting of the coal by electric chain machines across the face of the entry or room. This is followed by replacing any posts removed by the machine-runners, or the setting of new posts or timber, as may be required. After this has been done the machine cuttings are loaded into cars. Then the coal is spragged, and a shot hole drilled to the depth of the undercut. Next in order, the shot-firer loads the hole and fires the charge. The working place is then cleaned up, timbered if necessary, the sides and face squared up, and loose material taken down. The face is again ready to be undercut. Materials Used Permissible explosives were used exclusively in blasting coal. These were Carbonite No. 2, a nitroglyccrine explosive; and three different makes of ammonium nitrate explosives, Tunnelite, Red H, and Mine-ite 5-D. The last-named was used during the greater part of the period. It is interesting to note that even at the beginning of this work, the gases resulting from the explosions of the charges caused no especial distress on. the shot-firer's part and this continued to be the case except on the occasions when a change was made from one class of explosive to another.

Jan 1, 1918

By W. L. Remick

THE hydrotator coal-cleaning process was developed as an economic necessity to meet the ever-increasing demand for an inexpensive method of cleaning coal down to the sizes ordinarily referred to as "dust." As the most urgent demand seemed to be in the anthracite field, all experimental work has been conducted in that territory during the past 2 years, with the exception of a few months during the strike of 1925-26, when some experiments were performed in the Alabama bituminous fields. The first commercial plant was constructed at the Middle Creek Colliery of the Philadelphia & Reading Coal & Iron Co., Pottsville, Pa. This plant is now operating. APPLICATION The field of application of the process is: 1. Cleaning anthracite fines, ordinarily described as "slush" or "silt." Slush contains all sizes from %2 in. down to and including "dust." (Anthracite passing a 32-in. mesh is also referred to as No. 2 Barley and No. 4 Buckwheat.) 2. Cleaning sizes too fine for recovery by other methods. 3. Removal of coal from sand circulated in the Chance sand-flotation process. 4. Cleaning of bituminous sizes. from 3/8 in. down to "dust. 5. As equipment for the performance of the froth flotation process. 6. Other separating, extraction and _washing. processes which may be considered outside the realm of coal cleaning. PRINCIPLE OF OPERATION Fig. 1 shows the method of classification practised under the Hydrotator patent:1 In coal cleaning the machines are operated as "hindered settling" classifiers, the flow of solids and liquids being so controlled that the units may be combined in series.

Jan 1, 1927

By D. A. Elgillani, M. C. Fuerstenau

With either sulfonate or oleate as collector, quartz responds to flotation with moderate additions of calcium only at moderately high pH, where some portion of the activator has hydrolyzed to caOH+ . Calculations of the concentrations of various ionic and precipitated species of calcium and collectors suggest that the products of [(CaOH+) (RSO3)] and [(CaOH+)(01-)] determine whether flotation is obtained under specific conditions. Ion products on the order of 10-12 were calculated for both the sulfonate and oleate systems. The activating effect of calcium ion in nonmetallic flotation systems is of considerable interest because of the normal presence of calcium in natural water. As a result, this phenomenon has received quite some attention in the past. Kraeber and Boppel1 showed that quartz could be activated by calcium above pH 10 with sulfonate as collector. The feasibility of selectively separating quartz from hematite with calcium activation at relatively high pH was demonstrated by Clemmer, Clemmons, Rampacek, Williams, and stacy.2 Cooke and Digre3 showed with a bubble pick-up method that the minimum quantity of calcium ion required as activator for complete pick-up of particles occurs at pH 11.5 for an addition of 20 mg per liter sodium oleate. They also showed that larger additions of calcium (10-fold increase per unit decrease of pH) must be added for complete bubble pick-up as the pH is reduced. Schuhmann and Prakash,4 using a vacuum flotation technique, found that quartz could be floated with moderate additions of calcium chloride and oleic acid at neutral pH, providing the metal ion was present in stoichiometric excess over the quantity needed to form the normal soap with oleic acid. They also reported that calcium will function as an activator only in basic media. More recently, Eigeles and volova5 have shown that essentially complete flotation of quartz is obtained with 6 x 10-4 mole per liter calcium chloride and 1.7 x 10-5 mole per liter sodium oleate at pH 11.6. while no flotation is obtained at about pH 10.9 and below. The importance of adsorption of activator and collector at the air-liquid interface is also demonstrated in these systems. The important role that metal ion hydrolysis assumes in quartz activation systems was also demonstrated recently.6-8 A detailed investigation of metal activation in sulfonate flotation of quartz was undertaken in one system7 and yielded a number of interesting and important observations. Quantification of the data of this system7 to the extent desired was not possible, though, because certain species could neither be ignored nor accounted for accurately. These difficulties can be circumvented when calcium is involved as activator. This detailed analysis was undertaken to obtain a more quantitative explanation of calcium and metal ion activation in quartz flotation. EXPERIMENTAL MATERIALS AND METHODS Sodium alkyl aryl sulfonate9 mol wt 450, and pure potassium oleate were used as collectors. All other reagents used were reagent grade in quality, i.e., n-amyl alcohol as frother, KOH for pH adjustment, and calcium chloride. Conductivity water, made by passing distilled water through an ion exchange column, was used in the investigation. Quartz was prepared by leaching the sized sample (48 x 150 mesh) with HC1 until no iron could be detected in the leach liquor. The experimental equipment and procedure were the same as that described previously.6,10 EXPERIMENTAL RESULTS As the presence of precipitates was noted in all of the systems to which ca++ and collector were added, experiments were undertaken to determine the solubility products of calcium sulfonate and calcium oleate using a nephelometer. With this technique, collector is titrated into a known solution, which in this case was 5 x 10-5 mole per liter CaCl2 at pH 5.5. Upon precipitation of the calcium-col lector salt, e.g., calcium oleate, light is scattered and detected

Jan 1, 1967

By F. N. Rhines, T. E. Leonitis

The oxide scale that forms upon magnesium at elevated temperatures is non-protective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth' and has been verified by Suzuki2 and by ScheiL3 Pilling and Bcdworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki," he product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavaults observed that excrescences form upon liquid magnesium and alloys in thc course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium' and calciums minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.~ Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Schcil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. Experimental Procedure and Results The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the 6c

Jan 1, 1946

By T. E. Leonitis, F. N. Rhines

The oxide scale that forms upon magnesium at elevated temperatures is non-protective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth' and has been verified by Suzuki2 and by ScheiL3 Pilling and Bcdworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki," he product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavaults observed that excrescences form upon liquid magnesium and alloys in thc course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium' and calciums minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.~ Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Schcil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. Experimental Procedure and Results The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the 6c

Jan 1, 1946

By Andrew Mayer

Early in 1942 National Lead Co. was requested by the War Production Board to construct and operate a plant for the Government to produce magnesium by the ferrosilicon process which had been developed by Dr. E. M. Pidgeon in the laboratories of the Canadian National Research Council. A contract with the Defense PlantCorporation was concluded in May 1942 and Magnesium Reduction Co., a wholly owned subsidiary of National Lead Co., was formed to carry out this project. The capacity of the plant was rated at I0,000,000 lb. of magnesium per year, equivalent to an average production of about 14 tons per day. The Process The process, in brief, is as follows: The raw materials are dolomite and ferro-silicon, 75 per cent grade. The dolomite is calcined, the calcine and ferrosilicon are ground and mixed and the mixture is briquetted. The briquets are charged into tubular retorts of chrome-nickel steel set horizontally in a furnace with the open ends projecting outside the front wall. The retorts are then closed and evacuated. Magnesium is liberated according to then reaction 2(MgOl CaO) + Si = 2Mg + zCaO, Si% It is distilled from the charge and con- densed on a removable sleeve in the throat of the retort. Sodium and potassium, if present, are also liberated, distilled and condensed on a "sodium condenser" in the end of the retort. At the expiration of the distillation period the retorts are discharged and the cycle of operations is repeated. For the rated daily capacity of 14 tons of magnesium there are required approximately 170 tons of dolomite, equivalent to about 85 tons of calcine, and 16.5 tons of ferrosilicon. The retort residue, a bulky powder which at present is waste, amounts to about 87 tons. Choosing the Site The investigation to select the location of the plant was conducted by the Research Laboratories of National Lead Co. This work included geologic and economic surveys of a number of districts, examination of dolomite samples by chemical, spectrographic and petrographic methods and large-scale tests of dolomite from several of the more promising localities. in the last-named tests 2-ton samples were put through the ferrosilicon process in the pilot plant of the Canadian National Research Council, under the guidance of Dr. Pidgeon. The conclusions drawn from the investigation, in regard to the quality of dolomite to be used in the ferrosilicon process, were: First, the dolomite should contain not less than 21 per cent MgO and not more than 2 per cent acid-insoluble material. Second, the dolomite should

Jan 1, 1944

By V. Damiano, M. Herman

CELLULAR substructure observed in metal crystals grown from the melt. has been studied extensively'-' and is attributed to the existence of a constitutionally supercooled zone in the liquid ahead of the solidifying interface. The mathematical description of this process has been given in terms of the concentration of solute in the liquid phase, the rate of solidification, and the temperature gradien.t in the liquid as the only variables.5 This technical note presents some evidence of 1) the effect of crystal orientation on some aspects of cellular growth, and 2:) the degeneracy of these cells into dislocation arrays. The zinc single crystals used in these studies were alloyed with cadmium sufficient to produce the constitutional supercooled cellular substructure. Crystals containing 0.05 pct Cd exhibited substructure formation for a growth rate of 10 cm per hr and a temperature gradient of 15°C per cm in accord with the theory. The growing liquid-solid interface was examined after we liquid had been decanted away in a fashion similar to that described by Rutter and Chamers.' The cellular substructure was also observed after polishing and etching the surface directly behind the decanted interface with a solution of HNO, and water. Fig. 1 is a photomicrograph of a typical polished and etched surface revealing substructure, the cleavage plane, and twins. The crystal has been grown with its basal plane parallel to the direction of growth and the plane of the micrograph is per-

Jan 1, 1960

By R. W. Raymond

CLARENCE King born January 6,1842, at Newport, R. I. His ancestors on both sides mere New Englanders, of English blood, and among them not a few distinguished themselves in art, science, politics or commerce. His grandfather, Samuel Vernon King (partner in 1803 in the house of Talbot, O1yphant & King, later known as King $ Co.), was a pioneer in the China trade, and four of his sons succeeded him in the business. Three of the four died in the far East; and one of

Jan 1, 1903

By Edwin R. Phelps

In the year 1900 about 212 million tons of bituminous coal were produced in the United States. Almost none of this was produced by surface mines (Fig. 1), because there was no large equipment suitable for stripping overburden at that time. By 1915 the surface mines had built up their capability largely through use of the steam shovel to the point that they produced 2.8 million tons of the nation's total production of 443 million tons. Over the intervening years between 1915 and 1970 surface mining provided a continually increasing percentage of the nation's bituminous coal, stimulated by the growing availability of giant surface mining machines, some of which are presently capable of removing 220 cu yd of earth with one bite of their mighty buckets. In 1970 the nation's surface mines produced 244 million tons of bituminous coal, over 40% of the total national production. On the other hand, the nation's underground mines hit a peak of 560 million tons in 1920, dropped to a low of 273 million tons in 1961, and are presently on a very slow rise. Environmental pressures generally oppose surface mining, and have forced coal companies to consider more underground mining in future planning. Also, since strippable reserves are decreasing in the eastern states, an increase in underground mining is expected over the coming years. However, in the western states there are enormous reserves to be extracted by surface methods. Why has surface mining increased, while underground mining has decreased? It's largely a matter of economics. The cost per ton is greatly reduced by surface mining because of the relative ease of obtaining the coal. Also, there is a much greater percentage of coal recovery-nearly 85% in surface mines within the minable area, as compared to an average of about 50% in underground mines. Much surface mining recovers coal that could not be extracted by underground methods because of coal bed thinness, or multiple beds close together, split seams, the nature of the roof, and other geologic conditions. What are some of the limitations of surface mining? First of all, with presently available machinery it is difficult to surface mine at depths

Jan 1, 1973

By C. A. Siebert, G. Sandoz

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By G. Sandoz, C. A. Siebert

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By J. I. Paige, T. T. Campbell, A. W. Henderson, H. M. Harris

The chlorination of ilmenite concentrates and slags to produce Tic14 suitable for pigment or metal production was investigated by the Bureau of Mines along with the dechlorination of byproduct iron chloride to produce chlorine for recycle and iron oxide., Ilmenite concentrates or slag powders were fed into the bottom of a fluidized coke bed at 1,050º C using chlorine flow rates up to 20 l/min in a 10.2-cm-dim reactor. Tests showed that >95 percent of the various ilmenite concentrates reacted at optimum conditions, and recovery of TiC14 ranged from 95 to 100 percent of stoichiometric. Impurity dusts were removed from the vapors by cyclones and a fiberglass cloth filter. Iron chloride was condensed as a powder with less than 0.4 percent insoluble material. The TiC14 was collected in refrigerated condensers. Iron chloride was dechlorinated at 500º to 550º C by reaction with oxygen in a 16.5-cm-dim reactor using a fluidized bed of Fe2O3. Optimum processing was attained with a FeC13 feed containing 25 wt-pct Fe203 granules treated with 2 wt-pct NaCl catalyst; Under the above conditions, off gas chlorine concentrations of 62 to 90 wt-pct were obtained. During 2- and 3-day tests with technical-grade FeC13, conversion of FeC13 was 94 to 97 percent, chlorine concentrations were 76 to 90 wt-pct, and up to 92 pct of the stoichio- metric Fe203 was removed in the primary reactor discharge. Chlorine

Jan 1, 1976

By Maurice Cook

NORMALLY the grain size of cold-rolled and annealed copper sheet is of the order of 0.02 to 0.06 mm., and 0.1 min., for example, would, for many purposes, he regarded as undesirably large. The occurrence of very large grain sizes in a few isolated cases of copper sheet led the authors to inquire into the causes giving rise to such unusual results. During the course of this work a very large number of experiments have been carried out to determine the effect of varying the conditions of the final and penultimate rolling and annealing operations, as well as of earlier rolling and annealing treatments. A correspondingly large number of observations have been made, but within the space of one paper it is possible only to outline relatively briefly what appear to be the more important of these experiments and observations. The presentation of the results does not follow chronologically the order in which the experiments were carried out and they have been rearranged for the sake of simplicity. In recent years a considerable amount of work has been done in connection with the recrystallization and grain growth in metals and alloys that take place on annealing, and a number of generalizations have been reached. It is known that the crystal size in wrought material in the annealed condition depends on a number of factors, including the time and temperature of the annealing operations and the nature and amount of cold-work to which the material has been subjected. Results, however, that are not covered by these generalizations can be obtained, which, in some instances, may even appear to he contradictory to them. According to these generalizations gradual changes in grain size are effected by progressive variation of the factors involved in annealing or cold-working. The work recorded in the present paper, however, relates to the development of grain sizes which are far beyond those normally encountered in ordinary annealing operations and far in excess of grain sizes which, according to ordinary standards, would be classified as coarse or large.

Jan 1, 1938

By T. M. Berry

FOR the past several years it has been growing practice to install circular shafts at deep mining operations. Several factors have brought this about. Throughout eastern and midwestern coal fields circular shafts have been conventional for many years. Where large bodies of coal are mined, a production shaft may have a life of 20 to 30 years. Quantity production is essential; therefore the shaft must have a large cross-sectional area for larger skips and cages. Mechanical mining has become a necessity if a company is to stay in business today. Continuous mining machines and cutting, loading, and hauling equipment must be taken in and out of the mines. If the access shaft is not large enough there will be expensive dismantling and assembling. This has become a problem at many operations, particularly in the western sections where ore was originally mucked by hand into small cars and hoisted by a skip through a narrow rectangular shaft having small compartments. Mechanical loaders must be dismantled to wheelbarrow size to go into these mines.

Jan 7, 1957

By E. R. Parker, R. H. Thielemann

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By R. H. Thielemann, E. R. Parker

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By George R. Ensminger, E. Heaton Hemingway

During the past year, the Watertown Arsenal has been interested in the occluded gas and oxide content of certain ordnance steels in order to determine, if possible, whether some of the peculiar failures in their physical properties might not be traced to these causes. For the purpose of best accomplishing a study of this nature, it was decided to heat the various samples of steel in a vacuum for definite periods of time at high temperatures and carefully examine the quantity and composition of the gases evolved. By the use of a fused quartz tube fitted with a water-cooled, ground-glass stopper, it was possible to maintain a vacuum at a temperature of 1000" C. for 10 hr. without perceptible leakage being evidenced as measured by a McLeod gage. The silica tube was connected with an evacuating system so constructed that the volatilized gases could be removed from time to time and a low vacuum of 0.0002 to 0.0010 mm. of mercury continuously maintained. At no time during the period of heating or in the removal of the gases did the evacuated system come in contact with rubber stoppers or any rubber connections, making contamination from such a source, impossible. In other words, the only volatile products that could be: obtained must necessarily have come from the steel itself or from the glass and fused quartz system or from the mercury used as a sealing agent. In the carlier experiments, the steel treated was in the form of turnings, but this practice was discarded because the weight's of the turnings before and after being heated were widely inconsistent,, even when taken from the same piece of steel. This discrepancy developed largely through variation in the amount of metal volatilized with the gases; this metal could always be seen in the form of a ring where it condensed in the cooler portion of the tube in either the amorphous or crystalline condition. Because of the frequency in occurrence and the variation in the manner of deposition, this material was roughly analyzed and found to consist for the most part of iron. At the same time two samples of steel that had been

Jan 1, 1922

By E. Heaton Hemingway, George R. Ensminger

During the past year, the Watertown Arsenal has been interested in the occluded gas and oxide content of certain ordnance steels in order to determine, if possible, whether some of the peculiar failures in their physical properties might not be traced to these causes. For the purpose of best accomplishing a study of this nature, it was decided to heat the various samples of steel in a vacuum for definite periods of time at high temperatures and carefully examine the quantity and composition of the gases evolved. By the use of a fused quartz tube fitted with a water-cooled, ground-glass stopper, it was possible to maintain a vacuum at a temperature of 1000" C. for 10 hr. without perceptible leakage being evidenced as measured by a McLeod gage. The silica tube was connected with an evacuating system so constructed that the volatilized gases could be removed from time to time and a low vacuum of 0.0002 to 0.0010 mm. of mercury continuously maintained. At no time during the period of heating or in the removal of the gases did the evacuated system come in contact with rubber stoppers or any rubber connections, making contamination from such a source, impossible. In other words, the only volatile products that could be: obtained must necessarily have come from the steel itself or from the glass and fused quartz system or from the mercury used as a sealing agent. In the carlier experiments, the steel treated was in the form of turnings, but this practice was discarded because the weight's of the turnings before and after being heated were widely inconsistent,, even when taken from the same piece of steel. This discrepancy developed largely through variation in the amount of metal volatilized with the gases; this metal could always be seen in the form of a ring where it condensed in the cooler portion of the tube in either the amorphous or crystalline condition. Because of the frequency in occurrence and the variation in the manner of deposition, this material was roughly analyzed and found to consist for the most part of iron. At the same time two samples of steel that had been

Jan 1, 1922