Search Documents

By A. A. Jr. Smith, J. S. Smart

The controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modern copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range o to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously. Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,'v2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of %-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 8jo°C. from a surface scale. Test wires wcre drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in., and a final cold reduction of 75 per cent to 0.081 in. Oxygen-bearing slugs made by remelting nere hot-rolled to 4ia in.. drawn to 0.162 in., annealed for 30 min. at 6o0°C. and cold-drawn 75 per cent to 0.081 inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 3i6-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700' to 8o0°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals wcre of one hour duration followed by a rapid quench in 10 per cent HZSO*. Effect of Phosphorus The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1946

By A. A. Jr. Smith, J. S. Smart

The controlled amounts of phosphorus, arsenic, sulphur or selenium found in commercial coppers perform a variety of highly useful functions. Indeed, a large segment of modern copper technology is essentially dependent upon the presence of one or more of these elements. Consequently, the literature contains many references to their effects but the scope is broad and has been only partly covered. New data are presented herewith directed toward a better understanding of the basic behavior of these elements in copper, with particular emphasis on the composition range o to 0.05 per cent. These data are a part of a general program of research on the effects of impurities on the properties of oxygen-bearing and oxygen-free copper, other portions of which have been reported previously. Schematically, the behavior of individual elements is determined from measurements of conductivity and softening temperature,'v2 and the binary alloys employed are synthesized from high-purity copper in order to eliminate interference from the effects of extraneous impurities. Alloys of selected composition were first prepared in the oxygen-free form by continuously casting the melts in the form of %-in. diameter rod. Oxygen was added subsequently to portions of the alloys, either by remelting or by diffusion at 8jo°C. from a surface scale. Test wires wcre drawn one B. and S. number per pass, using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in., and a final cold reduction of 75 per cent to 0.081 in. Oxygen-bearing slugs made by remelting nere hot-rolled to 4ia in.. drawn to 0.162 in., annealed for 30 min. at 6o0°C. and cold-drawn 75 per cent to 0.081 inch. The alloys containing phosphorus, having been compounded very early in the program, were prepared in the form of 3i6-in. rod, and processed to wire with only the last three intermediate anneals listed above, all of these having been conducted in commercial nitrogen. In addition, the conductivity anneals on these alloys were also performed in the same atmosphere, and the small amount of oxygen present as an impurity in the gas resulted in some loss of accuracy at temperatures of 700' to 8o0°C., as will be shown later. Subsequently, the anneals for all oxygen-free alloys were conducted in hydrogen to prevent oxidation, and purified nitrogen was employed only for oxygen-bearing samples. All conductivity anneals wcre of one hour duration followed by a rapid quench in 10 per cent HZSO*. Effect of Phosphorus The widespread use of phosphorus as a deoxidant has resulted in universal appreci-

Jan 1, 1946

By Chester Purington

PROBABLY no battleship of any great power save Japan could long remain in. the Pacific Ocean tinder present conditions, were it to depend for fuel supply on the hitherto developed coal or oil resources of any part of the adjoining lands in either hemisphere. This statement does not overlook the important but not inexhaustible oil fields of California, the bunker coals of British Columbia, nor the coals accessible and mined adjacent to Chinese water-ways. For both naval and merchant ships, however, modern practice seems to require high-grade Welsh or Pennsylvania bituminous even at great expense for transportation. Otherwise, we should not see British ships bunkering Welsh coal at Singapore nor the United States establishing a store of Pennsylvania coal at its naval base at Pearl Harbor, Hawaii. Compared with Atlantic coals, the best Miike and Nagasaki (Japanese) bunker coal, the Kailan coal of China, and the Welling-ton and Nanaimo coals of British Columbia, are dis-tinctly inferior, as one can soon learn from the chief engineers on Pacific liners. In addition to the coal used for steaming and bunker purposes, it is of increasing importance that an adequate supply of coking coal for metallurgical purposes should be made available at reasonable prices at industrial centers on the west coast of America, and at Japanese and Chinese coastal cities. The use of Chinese coking coals for smelting the iron of the lower Yang-Tse deposits is by no means so satisfactory as could be desired, while the poor quality. of Japanese coals for coking purposes is well known. If Russia, as seems not improbable, is to become a power on the Pacific in the course of the next few decades, she will doubtless develop an iron and steel industry in the Maritime Province, where an adequate and accessible supply of iron ore will necessitate a supply of coking coal.

Jan 9, 1923

By Gifford White

CONSIDERABLE attention has been directed in recent years to methods of electric prospecting other than the conventional direct-current tech-niques. It has been extensively recognized that electrical data of a more general nature than that possible by direct-current methods might be useful in geophysical studies. To this end, a number of different types of electric currents have been employed, such as single-frequency alter-nating currents, square-topped periodic current waves,4 periodic surges of a less specific nature,8 and suddenly applied direct current.1,2 Yet, to the author's knowledge, little analysis of these different types of driving currents has been made from the standpoint of network theory to determine just what type of currents would give the most useful data, and, most important of all, to determine the relation of the data taken by one method to those of another. Without touching on the actual theoretical problem of how currents flow in the earth under specified boundary conditions, some very useful information can be obtained from the study of the fundamental integral equations of electrical networks, throwing light on the problem not ordinarily appreciated by the field worker. Some manipulation of the standard network equations will be made, with the sole purpose in mind of developing expressions leading to practical results. Suppose that four points in the earth have been located and it is wished to obtain the most useful type of electrical data by inserting current into two of them and measuring the potential developed between the other two. The first problem that arises is that of which pair of the four shall be chosen as current grounds. In the direct-current case, where only steady potentials are measured, the selection is of little consequence, but as soon as currents varying with time are used at the current grounds, a new effect arises. The fact that a varying current is flowing in the current-carrying conductor between the current grounds means that magnetic and electric fields varying with time will be produced

Jan 1, 1940

By Hiroshi Kato, Shin’ichi Nagashima, Hiroshi Takechi

The preferred orientations detleloped during cold rolling, annealing, and hot rolling of low-carbon steel sheets have been investigated by means of an inverse pole figure technique. And X-ray line profile meas-urerrlents were made for the study of the factor which causes the textural changes between cold-rolled and recrystallized sheets. From ND (sheet normal divection) and RD (rolling direction) inverse Pole figures tlze axis detisity change with increasing cold reduction was measured and the Preferred orientations were analyzed. These results can be explained by crystal rotation due to slip during rolling deformation. The ND axis density change during annealing of cold-rollitig sheets is contrary to the change observed in the case of rolling. It was found that the orientation dependency of stored strain energy resulting from cold rolling apparently corresponds to the textural changes during recrystallization. The texture in hot-rolled sheets was found to be influenced by finishing tenlperatltre. In a sheet kol-rolled below the Ar, temperature a significant differernce in texture between the surface and central layers was obtained, the former having {hkl}(111} and {110 )(uvw) orientations and the latter having {pqr}( 110) orientation. A large number of investigations1 6 have been made on the textures of iron and low-carbon steel sheets, and, since it was shown7 13 that preferred orientations are closely related to deep drawability of steel sheets, studies14" 7 on the influence of production processes upon textures have been made from the standpoint of industrial interest. Generally, the textures in low-carbon steel sheets have several components of preferred orientations, but the overlapping of poles makes it difficult to analyze texture quantitatively from pole figures. On the other hand, an inverse pole figure directly expresses quantitative values of components of preferred orientations as the density of a certain sample axis with respect to the crystallite coordinates. Such a texture representation is desirable for a study of deep drawability. The purpose of the present work is to use both inverse and conventional pole figures, with emphasis on the former, to clar~fy the textural changes ~n low-carbon steel sheets by the production processes of hot rolling, cold rolling, and annealing. And the factor causing the textural changes during annealing is studied using an X-ray diffraction line profile technique. EXPERIMENTAL PROCEDURE Sheet specimens for study of cold rolling and annealing textures were taken from a hot-rolled strip of rimmed steel 2.7 mm thick. The chemical composition is shown in Table I. Although the study of cold-rolling textures requires a suitable material with random orientation, it is difficult to produce a perfect random one. But the used specimens, obtained from the hot-rolled strip with a finishing temperature higher than Ar3, were nearly random, such as shown in Fig. 15. These were cold-rolled to various reductions by a 4-high rolling mill with 150-mm-diam work rolls and 300-mm-diam backup rolls. The influence of hot-rolling conditions such as finishing and coiling temperatures on textures of hot-rolled strips was studied. The chemical compositions of these hot coils are given in Table I1 and the hot-rolling conditions are given in Table 111. inverse Pole ~i~ure -~easurement. Two methods for determining inverse pole figures with high precision have been proposed. The first, by Jetter et a1.,18 consists of obtaining mean densities of divided regions in a unit stereographic triangle by solving simultaneous linear equations to approximate the integral relation between conventional and inverse pole figures. The second, proposed by ~oe'~-'~ and Bunge,22'23 consists of determining an expanded series of spherical surface harmonics which express axis densities from several sets of pole distribution data. Both methods require laborious numerical calculations which make them unsuitable for practical use. However, the axis densities of the locations corresponding to low Miller indices in a unit stereographic triangle can be obtained

Jan 1, 1969

By William P. Blake

In view of the present exposition at Atlanta, and the timely meeting of the Institute in that city, and the expressed desire of the Council for contributions to the knowledge of the mineral resources of the Southern States, I may be permitted to offer some desultory notes upon the subject, chiefly in the form

Jan 1, 1896

By AIME AIME

AN entirely new type of classifier is being put on the market by The Dorr Co., following three years of development and the experimental use of thirty machines of the improvement design in various parts of the world. It is known as the Multizone classifier. Compared with the older type the lower or overflow end has been decked over and is surmounted by one or more circular overflow columns. Feed is introduced near the middle of the machine and passes downward and under a vertical baffle, then along the underside of the deck to the base of the overflow columns. Under the baffle there is a restricted turbulent zone of high pulp velocity which holds the fine and critical size particles in suspension, preventing

Jan 1, 1937

The classification here used is one of convenience only; it is not intended to include all known types of ore deposits. The characteristic features of the several well-marked types of primary mineralizations are described without reference to the ultimate source of their metals. The minerals of many deposits of obscure origin were probably introduced through fissures that are now healed, or are due to the migration of metals from such deposits. [ ] It is not within the scope of this book to enter into a general discussion of the genesis of ore deposits but, in view of the progress being made in our comprehension of the conditions under which ore deposits were formed, mention should be made of recent work. J. E. Spurr's two volumes, "The Ore Magmas," are recommended as crystallizing the views of those who are inclined to ascribe the origin of most ore deposits to a differential precipitation from magmatic rock masses and to the migration and precipitation of the viscous, liquid or gaseous exhalations from those masses. He has especially emphasized the role

Jan 1, 1932

By R. I. Jaffee, H. P. Nielsen

In recent years much attention has been given to high melting alloy systems. It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. Past Work Miillerl determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from I771 C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Miiller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and Jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at I000 C. Vines and WiseS report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. Materials The platinum powder used in this work was kindly supplied by the Research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio. It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HC1. The resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1949

By Harry M. Mikami

Chromite is the only ore mineral of metallic chromium and chromium compounds and chemicals. Because of this fact, chromite and chrome ore are used synonymously in trade literature. In commercial market quotations, chrome ore is the term commonly used. Chromite per se, because of properties imparted by its chromium content, is used in refractories and in special purpose moulding sands for metal casting. There are many other minerals containing some, generally minor, amounts of chromium, but none are commercial sources of the element (Thayer, 1956, p. 15). Chromium and chromite have many diverse uses that, directly and indirectly, critically affect vast segments of our modern industrial system. Most important are probably the metallurgical applications wherein chromium is a component of heat, abrasion, corrosion, and oxidation-resistant, and high strength alloys of many types. Stainless steels are the largest volume category of chrome-bearing alloys. Chromium chemicals are used in leather tanning, in pigments, dyes and mordants, printing, :hemica1 process industries, photography, pharmaceuticals, metal plating, pure chromium metal production, and for many other purposes. Chromite is a necessary constituent in basic refractories indispensable for the production of steel, copper, cement, and glass. Under present economic-political conditions, he U.S. and for that matter, North America, has virtually insignificant ore reserves of chromite. There are chromite deposits, as will be described, but they would only be used under highly abnormal conditions if all outside sources were cut off. All chromite used in the U.S. is imported from the eastern hemisphere in which are contained the principal world reserves. As the main suppliers in 1971-72 were the USSR, Turkey, Republic of South Africa, Philippines, and Rhodesia, the strategic nature of chromite is obvious.

Jan 1, 1975

By G. Kimmel, A. Bar-Or

The rate of nucleation and the rates of both lateral and longitudinal growth of martensite plates (needles) in b—a transformation were determined as a function of temperature, in various U-Cr alloys. The activation energies for nucleation and both modes of growth were calculated from the experimental results. The identical values for lateral and longitudinal growth clearly indicate that both are controlled by the WHITE,' Mott and Hines and Holdeen3 showed that characteristic martensite plates (needles) appear in U-Cr alloys during the transformation 8 —0 in the lower temperature range (up to -300°C). Holden pointed out that the rate of growth of the individual martensite plates under isothermal conditions is same mechanism. Lomer's suggestion that single-atom movement over subatomic distances controls the specially slow growth of martensite receives further support from the present kinetic study, which shows that the growth rate can be described quantitatively by known formulas for the growth rate in processes involving single-atom movement. very slow, and suggested that this is due to the slowness of the relief of the stresses engendered during the growth of the individual plates. lomer4 attributed the slow growth to the complexity of the atomic adjustment at the growing interface b/(u. In the present work the rates of nucleation and growth of martensite plates in U-Cr alloys were studied by direct observation, in order to elucidate the mechanism which controls their characteristic slow growth.

Jan 1, 1968

By D. C. Hilty, W. Crafts

L. S. Darken—Laboratory investigation of deoxidizing and other steelmaking reactions is usually centered, at least first, on the determination of the equilibrium or equilibria involved. This seems a reasonable procedure since equilibrium, if attained, depends only on composition, temperature, and pressure; hence conclusions derived from data on small experimental quantities are applicable to a heat of steel providing eauilibrium is attained in both cases. A knowledge of equilibrium serves as a useful framework even though we may know that practical conditions do not correspond to complete equilibrium. On the other hand, nonequilibrium or rate phenomena depend on a wider variety of conditions and are more difficult to interpret; conclusions applicable to laboratory conditions may or may not apply to larger scale phenomena. Hence the attainment or nonattainment of true equilibrium in the experiments here reported is of critical importance in evaluating their significance. Since some of the statements in this paper and in the closely related preceding one (on aluminum deoxidation) imply some doubt on this matter, I should first like to ask the authors whether their conditions are intended and believed to represent equilibrium. I should like to point out three considerations which seem to cast considerable doubt on the achievement of equilibrium, at least of the particular equilibrium under consideration. 1. In the experiments on manganese deoxidation the authors point out that they could not maintain the manganese-oxide slag on top of the metal in their rotating crucible, and hence they substantially dispensed with this slag. This leads to serious trouble in the interpretation of the results, for any equilibrium is, of course, a particular specific equilibrium—in this case Mn + O = MnO The experimental deletion of the upper layer of manganese oxide means that if equilibrium is attained at all it is attained between the metal and the MnO which has soaked into or adhered to the crucible (under the metal) and has dissolved substantial amounts of the crucible material including impurities. These impurities may constitute a significant portion of the slag by virtue of the small total amount of slag, even though the crucible is relatively pure. Hence there would seem to be a strong presumption that the equilibrium (if attained) involves not a pure MnO (or MnO — FeO) slag but one saturated with alumina and containing perhaps considerable impurities which substantially lower the concentration and activity of MnO, causing the above reaction to proceed to the right further than it would in the absence of alumina and impurities. Hence it is not surprising that manganese here appears as a better deoxidizer than found by other investigators. The present results may represent equilibrium with a slag of unknown composition which seems unlikely to be particularly related to plant experience. 2. The curves representing the observed silicon deoxidation (figs. 3, 4, and 5) are all drawn with a discontinuity in slope at about 0.02 pct oxygen. This point is interpreted as corresponding to the three-phase equilibrium, metal, slag, solid silica. The type of construction shown in these figures (though apparently fitting the data) is contrary to a fundamental principle of heterogeneous equilibrium as pertains to the construction of phase diagrams. According to this principle, the two solubility curves (each of the two portions of the curves in figs. 3, 4, and 5) must intersect in such manner that their (metastable) extensions must lie outside the homogeneous field rather than inside as in these figures. In other words, the "point" in these curves should be aimed in the opposite direction, if it is to be interpreted as corresponding to the three-phase equilibrium. The construction adopted is in violation of the second law of thermodynamics. This matter is discussed in detail in several texts and also by Lipson and Wilson.&apos;" The same criticism applies to the later figures representing conditions for manganese additions. The occurrence of this discontinuity or break at 0.02 pct oxygen casts further doubt on its interpretation. The earlier investigation of this system by Korber and Oelsen is in substantial agreement with the several recent findings of Chipman and coworkers that the oxygen content of iron in equilibrium with silica and silica-saturated iron oxide slag is about one third to one half that (0.24 pct at 1600") of iron saturated with pure iron oxide; thus there seems reliable evidence that iron saturated with silica and iron silicate slag at 1600" contains about 0.1 pct oxygen, or certainly much more than the 0.02 pct proposed in this paper. 3. In the quarternary system iron-silicon-manganese-oxygen one of the equilibria involved may be written 2 Mn + SiO2 (solid) = 2 MnO <slag> + Si The activity of SiO, is constant (if equilibrium is attained) by virtue of its presence as a substantially pure solid. At not too low metallic manganese content, the activity of MnO in the slag is constant by virtue of the fact that the slag is substantially pure manganese silicate saturated with silica and hence of constant composition. Thus the equilibrium constant for the above reaction is asi/a2Mn. Barring unanticipated large changes in the activity coefficients, the equilibrium constant may be adequately approximated for the composition range covered as [% Si]/[% Mn]2. Thus a plot of log [% Mn] against log [% Si] would be expected to be linear with a slope of one half as found by Kijrber and Oelsen. In the present investigation the slope (shown in fig. 15) is found to be one. It is difficult to believe that this finding represents a correct equilibrium determination, since it is at odds both with prior experimental investigation and with. theory. In view of the above points it seems that, although this paper reports many interesting findings, there is room for considerable skepticism as to the attainment of equilibrium and as to the conclusions drawn. N. A. Gokcen—The authors consider that Si% x O2% product is constant. This product is a function of the asi X a0 activity of Si02. The true constant is -------------. If the asio2 slags of this investigation were always saturated with SiO2 then Si% X O2% product would be constant,

Jan 1, 1951

Prof. H. S. Munroe, New York City : In his reference to cop per-dressing at Lake Superior, p. 325, Mr. Douglas says that " the .. concentration .. . has been carried out with greatest financial economy,... I do not say with the greatest economy of min eral." And again, on p. 344, referring to the same, " it would not pay to reduce the quantity treated, and increase hand-labor, in order to save a few hundredths of one per cent. of copper." Mr. Douglas probably has in mind the fact that the copper lost is all included copper, locked op in grains of sand. To save this, the rock must be crushed finer. If the mesh of the stamp-screens be reduced, the stamps will crush less; and thus we shall have to reduce the quantity treated in the mill per day, while the labor re mains the same per day, or is increased per ton, as he says. Submitting to the loss of copper, however, is not the only solution of the difficulty. A large quantity of rich sand is now collected by the jigs, and it would be easy to save so much of this material that the escaping sands would be quite poor. What is wanted at Lake Superior, and at many dressing-works in this country, is an efficient crushing-machine to treat the sands thus collected. Abroad, we have the Heberle machine and the Schranz mill for this purpose, the latter being the more successful. The Heberle grinder was tried at the Calumet and Hecla mill for crush ing these rich sands, with what success I do not know. I should like to ask Mr. Douglas if we have no American crushing-machine that will reduce jig-sands to a fine state of division

Jan 1, 1894

By G. R. Love, C. C. Koch

The changes in superconducting properties with aging time have been studied ,for the pecipitation reaction in a Tc-30 at. pct V alloy. Superconducting critical temperature, upper critical field, and relative critical current density were determined by ac susceptibility techniques. Aging produces changes in critical temperature of both matrix and precipitate which can be rationalized by compositional effects. maximum flux pinning (critical current density) occurs at a time during aging when subgrain boundaries are completely decorated with precipitates and the subgrain centers remain precipitate -free. The particular effectiveness as barriers to flux motion of planar defects which enclose regions of low deject density is discussed. THE precipitation of a second phase can dramatically modify the superconducting properties of type I1 super-conductors. According to Livingston and Schadler1 one might expect changes in the primary, secondary, and tertiary superconducting properties of the material. Changes in matrix chemistry caused by precipitation can alter the fundamental superconducting parameters; critical temperature, Tc, and thermody-namic critical field, Hc. The concimitant changes in electron mean free path (reflected in normal state resistivity) can affect the critical fields Hc 1, IIc2, Hc3. Finally, the presence of precipitate particles may hinder the motion of flux lines and may considerably improve the current-carrying capacity in high-field superconductors. The influence of precipitation on superconducting properties has been studied in a number of systems.2 Magnetization measurements have been used to study the influence of precipitates on flux pinning in lead-base alloys by Livingston3 and Evetts et al4 In these alloys precipitates induced magnetic hysteresis and flux trapping. The amount of hysteresis increased with the volume fraction of precipitate and decreased with coarsening of the precipitate. Jn an Al-Zn alloy5 and an A1-Ag alloy6 the initial precipitate size was presumably smaller than a coherence length and coarsening increased magnetic hysteresis5 and critical current density.6 The influence of precipitation on superconducting properties has also been studied in several of the commercially interesting Ti-Nb7-10 and zr-Nb11 alloys. The maximum in critical current density for these alloys was confined to a narrow range of either isothermal aging time" or isochronal aging temperature7 during the precipitation reaction. Thus, experimental evidence and theoretical considerations suggest there is an optimum precipitate size, spacing, and density, and a critical composition with respect to the matrix for flux pinning. What these "optimum" values might be and the relative importance of each is still not clear, although a few generalizations can be made. It is generally accepted1&apos; that particle sizes smaller than the coherence length or larger than the inter-flux line spacing are poor pinning centers. In high Hc2 materials, precipitate sizes for maximum values of critical current density lie in the range of 50 to 2000Å,9,7 and there are indications that increasing dissimilarity between precipitate and matrix produces increasing pinning force.13 Because of several interesting features of the aging reaction in a Tc-30 pct V alloy, we have chosen to study the influence of precipitation on the superconducting properties of this alloy. The physical metallurgy14 and a survey of the superconducting properties" of the Tc-V alloy system have been reported. The Tc-V phase diagram is presented in Fig. 1. At 1500°C the Tc-30 pct V alloy is in the single phase 6 field. Samples quenched from the 6-phase field have a CsCl structure X-ray diffraction pattern at room temperature and it has been proposed that the 6 structure is closely related to the bcc lattice.14 When held isothermally below the eutectoid temperature, 115O°C, the 6 phase decomposes into the CsCl and hcp phases.

Jan 1, 1970

By J. C. Norman

Jan 1, 1985

By Jr. Ensign C. O., J. W. Trammell

The two principal methods of room-and-pillar mining practiced at White Pine make it important to predict variations in the thickness and rock types of a stratum called the upper sandstone. In full column mining, the nearly barren upper sandstone occurs between two ore horizons (called upper shale and parting shale, respectively), and is mined as a part of the ore column. In general, full column mining is not practiced where excessive upper sandstone thickness causes full column ore grade to be substantially lower than parting shale ore. In parting shale mining, the upper sandstone forms the mine roof. Difficulty in predicting upper sandstone character arose because the extent and directions of its variations were not apparent in the property&apos;s diamond drilling, in which holes are spaced on 1000-ft centers. A study of sedimentary features, undertaken to improve the predictability of trends in the upper sandstone, led to an interpretation of the sedimentary environment in which the sandstone was deposited. Ripple marks, mud cracks, and cross-bedding, as well as other, less well known features, such as channel casts, flute casts, and current crescent casts, were mapped or recorded. These data, coupled with the knowledge of regional facies changes gained from studying drill core, show that the upper sandstone was deposited by a series of streams flowing northeastward over the underlying parting shale. Deposition of the lowermost bed of the upper sandstone, near the ancient shoreline, was locally preceded by erosion of the parting shale, and the greatest thicknesses of sandstone are found in channels scoured out of the parting shale. Awareness of the rather strong linear trends in the upper sandstone makes it possible to project continuous areas of thick upper sandstone through apparently isolated "highs" in the upper sandstone thickness contour map, which is based on drill-hole information. Since local exceptions to general stratigraphic trends exist, a method was also needed for esti- mating, in detail, the thickness and degree of shali-ness of upper sandstone forming the roof in active parting shale mining areas. Because locally the parting shale was thinned by erosion during the deposition of upper sandstone, parting shale thickness is inversely proportional to upper sandstone thickness. Utilizing information taken from short drill holes into the roof, curves were constructed for the correlation of parting shale thickness (measurable in the mine) with the upper sandstone total thickness, as well as the thickness of its basal member. The White Pine mine is situated in Ontonagon County, approximately 6 miles south of Lake Superior, in the Upper Peninsula of Michigan (Fig. 1). The orebody mined by White Pine Copper Co. occurs in the lowermost 20 to 25 ft of the Nonesuch formation, a series of middle- to upper-Keweenawan shales, siltstones, and sandstones. This paper discusses the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the orebody. THE OREBODY AND MINING TYPES A brief description of the orebody and mining methods is necessary to show how the upper sandstone affects mine planning and grade control. In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions, as shown in Fig. 2. Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 2. Other authors1&apos;3 have dealt in detail with the stratigraphy and mineralogy of the orebody. However, in this article, we are concerned with the major subdivisions only, and it will suffice to note the low copper content of the upper sandstone, shown in Fig. 2. At present, two types of room-and-pillar openings are created in the orebody. In one type, called parting

Jan 1, 1964

By William E. Ford, Edward Salisbury Dana

WheweUite. Calcium oxalste CaCz04.Hz0. In small colorless monoclinic crystals. Optically +. j3 = 1.555. From haxony, with coal; also from Bohemia, and Akace. Oxammite. Ammonium oxelate, (N&)rC20r.2HzO. From the guano of the Gudape Isbnds, Peru.

Jan 1, 1922

By Herbert Clark Hoover, Lou Henry Hoover

QUALITIES which the perfect miner should possess and the arguments which are urged for and against the arts of mining and metallurgy, as well as the people occupied in the industry, I have sufficiently discussed in the first Book. Now I have determined to give more ample information concerning the miners. In the first place, it is indispensable that they should worship God with reverence, and that they understand the matters of which I am going to speak, and that they take good care that each individual performs his duties efficiently and diligently. It is decreed by Divine Providence that those who know what they ought to do and then take care to do it properly, for the most part meet with good fortune in all they undertake; on the other hand, misfortune overtakes the indolent and those who are careless in their work. No person indeed can, without peat and sustained effort and labour, store in his mind the knowledge of every portion of the metallic arts which are involved in operating mines. If. a man has the means of paying the necessary expense, he hires as many men as he needs, and sends them to the various works. Thus formerly Sosias, the Thracian, sent into the silver mines a thousand slaves whom he had hired from the Athenian Nicias, the son of Niceratus1. But if a man cannot afford the expenditure he chooses of the various kinds of mining that work which he himself can most easily and efficiently do. Of these kinds, the two most important are the making prospect trenches and the washing of the sands of rivers, for out of these sands are often collected gold dust, or certain black stones from which tin is smelted, or even gems are sometimes found in them ; the trenching occasionally lays bare at the grass-roots veins which are found rich in metals. If therefore by skill or by luck, such sands or veins shall fall into his hands, he will be able to establish his fortune without expenditure, and from poverty rise to wealth. If on the contrary, his hopes are not realised, then he can desist from washing or digging. When anyone, in an endeavour to increase his fortune, meets the expenditure of a mine alone, it is of great importance that he should attend to his works and personally superintend everything that he has ordered to be done. For this reason, he should either have his dwelling at the mine,

Jan 1, 1950

By F. E. Bash

A GREAT many industrial operations require the application of heat to carry on or complete processes, in which cases the temperatures must often be controlled within very narrow limits. For the lower temperatures, this control is not, as a rule, difficult as a number of types of reliable pyrometers are available for the work; for example, the mercury and resistance thermometers and the thermocouple. For temperatures above a red heat, thermocouples, platinum resistance thermometers, and total radiation and optical pyrometers may be used, depending on conditions. It is often undesirable, and sometimes impossible, to take temperatures of material by immersing the pyrometer in it or by placing the temperature-measuring device in a position in which it will attain the temperature of the material. The pyrometer may contaminate the product; the temperature may be so high that the pyrometer will not hold its calibration, clue to ineffectual protection and consequent contamination; the object may be inaccessible, as a lamp filament, etc. In such cases, a total radiation or optical pyrometer must be used. The disappearing-filament, or Morse, type of optical pyrometer works on the following principle: An objective lens, Fig. 1, focuses the image of the object whose temperature is desired in the plane of the lamp filament at F, which is at the principal focus of the ocular lens shown in the eye-piece. By this arrangement the eye will not have to accommodate itself first to the lamp filament and then to the object at a distance, and the lamp filament will appear superposed on the object. To balance the instrument, the current is adjusted by means of a rheostat until the tip of the lamp filament just disappears against the object as a background. Figs. 2, 3, and 4 show the appearance of the filament when too cold, too bright, and just balanced.

Jan 8, 1919

By J. E. Hilliard

It is proposed that shape anisotropy in the internal structure of materials be defined by distribution functions which specify what fraction of the total line length or boundary area lies in a given direction. Methods are descriibed for determinirg these distribution functions from measurements on sections through an opaque material. New derivations, that have certain advanifages over those given previously, are Provided for well-known expressions used in estinzating the total density of lineal or areal features. INCREASING attention is being given to the quantitative description of imicrostructures in metals and other materials. This interest stems from the recognition that the structure often provides a convenient half-way point between the properties on the one hand and the processing variables on the other. Such cross correlations become increasingly desirable as materials become more complex and the demands on them more stringent. One of the principal aims in structure analysis is therefore to find parameters that are readily measurable and specific enough to be correlated with other properties of the material. Certain properties, such as magnetic and mechani cal behavior, are strongly influenced by structural anisotropies; in order to relate such properties to the structure it is obviously necessary to have means of specifying and measuring the type and degree of anisotropy. For the determination of preferred orientations in crystal structure, X-ray diffraction methods are available and are widely used, but scant attention has been given to the estimation of anisotropy in the shape of grains and particles. It is the latter problem that will be considered in this paper. It is evident that shape anisotropy can be describe in terms of preferred orientations of lineal and area elements of the structure. It will be shown that these preferred orientations can, in turn, be specified by distribution functions that define what fraction of the total line length or boundary area lies in a given direction. Methods will be given for determining the distribution functions from measurements on sections through the structure. Even when the orientation distributions are of no interest per se, they still have an important bearing on the measurement of the total line length or boundary area by means of an intercept analysis. The treatment in terms of orientation distribution functions leads to new derivations, that have certain advantages of those given previously, for the well-known expressions used in estimating the total density of lineal or areal features. The treatment is divided into two main sections. The first deals with the orientation distribution of a two-dimensional array of lineal features such as occurs in the projected image of dislocations in electron transmission microscopy. The other section treats the estimation of the distribution of lineal and areal features dispersed in three dimensions.

Jan 1, 1962