Search Documents

By E. Gybbon Spilsbury

(Pittsburg meeting, March, 1910.) THE recovery of gold and silver from their ores by means of the cyanide process has been so successful in the last few years that any radical improvement would seem impossible; yet the appliance to which I wish to call attention in this paper is really a radical departure from the methods now in general use. The most modern and approved of these, known as the all-sliming method, depends for its success on the grinding of the. ore so fine that practically 90 per cent. of it will pass through a 200-mesh screen. The slimes thus produced are then agitated and aerated in tanks of various types. The main object of this treatment is to insure such a thorough admixture of the pulp and solution that every particle of the ore is surrounded by a volume of solution sufficient to insure the dissolving of the whole of the gold- and silver-content. In addition, in order to expedite the action of the cyanide, and to oxidize such elements as would, if left in their active state, become cyanicides, air is blown in under pressure. In the Pachuca tank, this air is the active and sole means of agitation. The chief objections to all the methods off agitation used heretofore are the expense of operating and maintaining the mechanical devices for keeping the pulp in suspension, and the length of time required to obtain a fairly complete extraction. of the values. These objections are inherent to any method of agitation effecting a circulation of the pulp and the solution together, by giving the whole mass a circular movement, as in the low-tank system, or a vertical circulation, as in the Pachuca-tank system. In both methods, the particles of ore are kept traveling in the same direction as the solution, and with very little difference of speed; so that, while the whole mass is in

May 1, 1910

D. M. Riordan has been appointed a member of the Institute Com¬mittee of the Engineers' Reserve Corps movement. Our Committee, therefore, now consists of Henry S. Drinker, Chairman, Messrs. Arthur S. Dwight, Warren A. Wilbur and D. M. Riordan.

Jan 1, 1916

By Ronald J. Roman

Research pertaining to flow of solutions in leach dumps has generally been neglected. This technical note proposes a method for evaluating the flow patterns and incorporating the results into dump-leaching models. Three dump-leaching models1-3 have been proposed to scale up laboratory test data to expected field results. These models are based on the same physical picture in a dump and differ only in the importance of diffusion or surface chemical reaction rate. Selection of this rate-controlling phenomemon is based on type of ore (sulfide or oxide), physical dimensions of the particles being leached, and the leach heap itself. All three models are applicable to specific types of operations. The models are similar in the use of a size distribution analysis for the dump material and the assumption that the leach solution flows around each particle. Transport of the leaching agent to the interior of the particle takes place by diffusion [(Fig. 1)]. However, normal dumps are of a higher bulk density than the material in a laboratory column used to generate the scale up data. How does this difference in bulk density affect the scale up equations? Increasing the bulk density can be expected to give more particle-to-particle contact; therefore, individual particles will be blinded by each other. As blinding increases with bulk density increase, the particles will behave like larger particles with a coarser apparent size distribution. The extreme will occur when the bulk density reaches that of the undisturbed rock, the entire dump behaving as a single particle with the dimensions of the heap itself. Harris4 alluded to this phenomenon in his paper. An alternative method of describing the same phenomemon is to consider the flow paths of the solution. At high bulk densities leach solution no longer surrounds each particle, but flow paths are separated by several particles and channeling is said to take place. Instead of the particle radius being the maximum distance through which the leaching agent must diffuse, the maximum distance is half the separation distance of the solution flow path. Particle size distribution must then be replaced in the models by the concept of channel separation distribution. Like size distribution, channel separation distribution specifies the cumulative percentage of the rock in the dump situated less than a specified distance from a solution channel. Thus, [ ] Distribution of the solution channels is a function of how the dump was built (among other things), and therefore it cannot be determined in the laboratory. Accordingly, it becomes necessary to determine a range for d and a in existing operations or measuring these parameters before leaching starts. Howard5 gives a clue to one possible technique of measuring solution channel distributions. When his paper was published little was known about the phenomemon of leaching; the importance of this type of data was not recognized. [Fig. 2] is a Y-Y log for one hole drilled

Jan 1, 1978

By W. A. Wood, H. M. Bendler

Cylindrical fatigue specimens of OFHC* copper were subjected to alternating torsion while under axial tension. The superimposed tension strongly influenced the fatigue life of the specimens as well as causing characteristic changes in the structure of the fissures that form and develop throughout the life of the specimen. A further effect of the superimposed tension is a continuous extension of the specimen throughout its life in a manner formally similar to creep at elevated temperatures. RECENTLY, studies of the structural changes leading to fracture of metals by fatigue have been made by a technique which reveals, in section, the lattice distortion arising from slip movements inside the metal and the disturbances built up by these slip movements at the metal surface.1'2 According to this approach, fatigue develops as follows: a) fine slip movements concentrate in bands, producing little strain-hardening and thus permitting abnormal totals of plastic strain before fracture and, therefore, abnormal amounts of lattice distortion along each slip band; b) both forward and backward slip movements occur in each band which, according to their distribution across the band, may build up surface disturbances that include sharp notches; c) these notches early in the life of a specimen penetrate the distorted slip zones and transform them into deep, fine fissures; d) the fissures on continued cycling locally saturate the metal and cause local collapse in the form of a microcrack. Thus, the significant consequence of fatigue or cyclic

Jan 1, 1962

THOMAS T. READ, Palmerton, Pa. (communication to the Secretary*). -It is much to he regretted that in presenting a further discussion of these deposits, first described by myself' and later discussed by C. M. Weld,2 Mr. Wang bas not made a more complete presentation of the evidence on which he bases his conclusions as to their origin. Mr. Weld said in his paper that his visit was confined to a few hours, that he saw only one of the several exposures, and that he took away no samples for further study. My own visit was brief, and for another purpose than the study of the geological features of 'the deposits, so the fact that Mr. Weld described as a hornblende-granite the rock which I described as a "dark gray syenitic rock," and which Mr. Wang identifies as a hornblende-syenite, seems of no great importance, since this rock is generally decomposed along the contact, presumably the only place in which Mr. Weld observed it. Later in the same paper (p. 31), Mr. Weld says that his opinion is that the magnetite of the deposits is primary, but Mr. Wang makes no mention of this in stating his own conclusion to the same effect. When Mr. Weld's paper appeared, I did not discuss it, because, although I considered the evidence- that he brought forward to support his belief that the magnetite is primary too slender to support the hypothesis, my own evidence to the contrary was equally tenuous. .The opportunities for observation and study open to Mr. Wang must have provided him with

Jan 6, 1917

CAPTAIN JOHN H. BALLAMY John H. Ballamy, Captain on the Regimental Staff of the 103d Engineers, was killed near Fismes, on August 9, 1918. Captain Ballamy was born at Plymouth, Pa., in 1886 and graduated from the High School of that town in 1903. In the following year he began work as a coal miner, and at the same time began the study of mining engineering in the evening and any other spare time. He continued this diligent and energetic practice for many years. For sixteen years he continued in the employment of the Delaware, Lackawanna & Western Railroad Company's coal mining department, first as a practical miner, next as rodman on the survey corps, of which he soon became chief, then draftsman and mining engineer in the company's office. In January, 1916, he was promoted to the position of district engineer in charge of mining engineering work. He became a member of this Institute in September, 1917. CAPTAIN JOHN H BALLAMY. Captain Ballamy's military experience began at the same time as his engineering practice. He was a charter member of Company A, Engineers, N. G. P., which was organized ten years ago. He saw service on the Mexican border as First Lieutenant of this Company, and remained in that position until November, 1916. In July, 1917, he was again called into service and was sent to Camp Hancock, Ga., with the 103d Regiment of Engineers. Before joining this regiment he attended a school for officers at Fort Sill, Okla., where he received special training in field fortifications. In December, 1917, he was commissioned Topographical Captain on the Regimental Staff, and in April, 1918, preceded his regiment by about six weeks to France, where he again attended an officers' training school. He rejoined his regiment on July 15, near Chateau Thierry and was killed near Fismes on August 9, 1918.

Jan 11, 1918

By W. Philippoff

ALTHOUGH Gaudin1 and more recently Sutherland2 have calculated the probability of collision of a falling mineral particle with a rising bubble, there is no published information concerning the details of the mechanism of attachment of a collector-coated particle to a bubble. During the past year the writer has developed a theory for the mechanism of attachment, which has been substantiated experimentally.' Funds for the investigation and for some of the equipment used have been supplied by the Mines Experiment Station of the University of Minnesota. Motion picture studies of the phenomena involved in the collision between mineral particles and bubbles, such as those of Spedden and Hannan,3 show that the contact can be completed within 0.3 millisec. Formulas developed for rigid bodies have hitherto been used' for the calculation of the motion of bubble and particle, but it is obvious that a bubble cannot be regarded as a rigid body. On the contrary, Spedden and Hannan's pictures show a great degree of deformation during the collision. The time of attachment was calculated as the time the particle drifted past the bubble. Time of Collision The theory presented in this paper enables calculation of the time of collision; using the concept that the bubble, or more generally, a liquid-air interface, acts as an elastic body. The elasticity, defined as the restoring force on a mechanical deformation, is caused by, the surface tension and is the result of the principle of the minimum of free surface energy. It is well known that an elasticity together with a mass determines a frequency of vibration. The vibrations of jets and drops caused by the elasticity of the interface are known to comply exactly with the classical theory of capillarity.5 However, the vibrations of isolated bubbles, as distinct from foams, have not been investigated previously. The following equation, presented elsewhere,' has been deduced for these frequencies: [3fB = 9.20•'./V•Vn- (n-1) • (n+2) /8[1]] in which fB is the frequency of a harmonic of the bubble in cycles per second, V the volume of the bubble in cc, n a number determining the order of the harmonic, and n = 2 the basic vibration. The first (basic) harmonic describes a change of the spherical bubble to an ellipsoidal bubble. The higher harmonics are more complicated, for the circumference of the bubble is divided approximately into as many parts' as the order of the harmonic. As an example, Spedden and Hannan's published motion picture of, a vibrating bubble corresponds to the sixth harmonic. Eq 1 shows that only the first and third harmonics are simple multiples (1 and 3), all the others being irrational fractions of the basic frequency. This means that the shape of the vibration can change with time and is in general unsymmetric in respect to the time axis. Such conditions prevail when there is a distributed elasticity or mass, as in the case of vibrating membranes or rods. The constant 9.20 is valid for water at room temperature, but a general solution involving the physical constants of the liquid has not been found. The case of the floating particle is much easier to treat I than that of the bubble. It can be assumed that the elasticity is caused exclusively by the interface and that the mass is concentrated in the particle together with some adhering water. The following expression for the frequency of a system, of one degree of freedom can be applied: [1E/m[2] fP = 27] Here f, is the frequency of the particle vibration in cycles per second, E the elasticity in dynes per cm, and m the mass in grams. The classical theory of impact phenomena gives the time of collision during the striking of a spring (in this case the surface of the bubble) by a mass, as: [t~ = 2/f = 7r\/m/E[3]] It is now possible to develop an expression for the elasticity of a floating cylindrical particle. The force equilibrium of a cylinder floating end on at the air-liquid interface is given by the well-known equation (Poisson' 1831) [aP = 4 D2.pL•g•h +7rD•y sin a[4]] which accounts for the buoyancy and the action of the surface tension where P is the force acting on the particle in dynes (weight-buoyancy), D the diameter of the cylinder in cm, pL the density of the liquid in grams per cc, g the acceleration of gravity = 981 cm per sec2, h the depression of the cylinder below the surface of-the liquid in cm, y the surface tension in dynes per cm and a the supporting angle' or the one required to insure equilibrium, a being smaller than the contact angle ?. Although demonstrated by Poisson, it has not

Jan 1, 1952

By F. H. McDowell

For more than two hundred years Mexico has been enriching the world from her inexhaustible wealth of precious metals. From this source alone, over three thousand five hundred millions of dollars have been poured into the coffers of Europe and America. During these centuries the wants of the country in manufactured goods have been supplied from the mills and machine-shop of the Old World. English, French and German merchants in Mexico have vied with each other in their efforts to control the importing of these goods from their respective countries. The overthrow of Maximilian, the departure of the French and the restoration of the Republic, largely influenced by the strong stand taken by the United States Government during our own civil war, established a new order of things. Americans were encouraged to visit the sister republic, examine into the needs of the country, as well as its resources, and interest themselves in the work of development. More recently, under Presidents Diaz and Gonzales, liberal inducements have been extended to American capitalists to build railroads, open mines, erect reduction-works, raise cattle and improve the crude systems of agriculture. The Mexican Central Railway has been pushed south from the Rio Grande to the Capital, and, by its branches and connections, makes the whole mineral belt of the country accessible.

Jan 1, 1885

By L. D. Ricketts

Discussion of the paper of L. D. RICKETTS, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 100, April, 1915, pp. 711 to 737. FREDERICK LAIST, Anaconda, Mont.-I am going to tell you of some of the results we have been getting in Anaconda during the past two or three months in a large plant which was finished in May. We commenced work in Anaconda a year and a half ago on the construction of a leaching plant which was to have a capacity of 2,000 tons per day. The plant was to treat tailings from the concentrator, containing about 12 1b. of copper to the ton. During the past year we changed our plans and decided to use the flotation process on the tailings from the concentrator, which contained no oxidized copper, and apply the leaching process only to tailings which had accumulated in a large dump below the works. This dump contains about 15,000,000 tons of tailings, and since some of the copper in it is oxidized, we felt that the application of the flotation process would result in the loss of too much of the oxidized copper, particularly as time went on. In starting up we had a number of difficulties to overcome, as is usually the case. They were not of a serious character. The results obtained, so far, have been decidedly encouraging. During July the plant treated a total of 50,000 tons of tailings, or an average of 1,610 tons per clay. The extraction was about 83 per cent., which, on material of the grade treated, meant a. tailing assaying under 0.1 per cent. copper. The acid consumption was about 65 lb. per ton, and the fuel percentage in. roasting was about 4 ¼ . We expect to cut the fuel percentage in the next month or two to about 3 per cent., the high percentage during July being clue to starting up and shutting clown furnaces. We find that iron builds up in the solution to a marked degree. This is not a serious platter with us, because we have cheap sulphuric acid and can reject solution whenever it gets too foul. The extraction of silver has been remarkably good in the large plant. It has averaged better than 75 per cent. It seems that so long as we maintain salt in the solution to a percentage of 10 per cent., the extraction is good. We allowed the salt to fall off in order to find how low a percentage we could use. At about 7 per cent. the silver extraction fell to 65 per cent. This was to be expected, because silver chloride is soluble in strong brine, but not in weak brine.

Jan 12, 1915

By THOMAS LEONBRD WATSON

INTRODUCTION. IN a paper read by title at the Washington meeting of the Institute, May, 1905,1 discussed at considerable length the geological relations, node of occurrence, and the genesis of the lead- and zinc-ores of the Virginia-Tennessee region. The present paper treats of the purely economic phases of the zinc-ores of the district; such as methods of mining the ores, their preparation and treatment. The Albemarle county mines and plant were discussed in the paper referred to above, and will not be considered here. METHODS OF MINING. Until very recently the mining of lead- and zinc-ores in Virginia was limited wholly to the surface belt of weathering. The mode of occurrence and the character of the ores to be mined were such as to demand the employment of methods used in mining secondary concentrated ores. Accordingly, a system similar to that practiced in mining brown iron-ores was employed, being modified to meet the changed conditions. Oxidized or Soft Ores.-Up to the present time practically all the ore mined in the Virginia district has been of the oxidized or soft type;-the silicate, calamine, and the carbonate, smith-sonite; largely the former, which has been localized and concentrated at only slight depths below the surface. Because of the extreme irregularity with which the limestone weathers when stripped of the overlying residual clay, it presents a roughened surface of large and small irregular "chimneys"

Mar 1, 1906

By AIME AIME

ABOUT one hundred were in attendance when Donald M. Liddell opened the session* on non-ferrous metallurgy at 2 p. m. on Tuesday. F. F. Col- cord was vice-chairman. For the first part of the session the chair was turned over to Frank G. Breyer, who introduced G. L. Spencer, Jr., to read his contribution (T.P. 378), "High Silica Retorts at the Rose Lake Smelter," which was an account of the method of manufacture of high-silica zinc retorts at the Rose Lake smelter, and of the service given by these retorts. The materials used are, by volume, 50 per cent clay, 25 per cent silica flour and 25 per cent grog. Written discussion of the paper by E. M. Johnson, W. R. In- galls and M. M. Neale was read by Mr. Breyer. Mr. Johnson explained that their practice in manufacture differed very little from Rose Lake practice, but that their retorts did not last as long, possibly because Eagle-Picher does not use a hydraulic retort press or sintered ore. He ascribes the longer life of silica re- torts to the fact that they do not bend under heat. Mr. Ingalls pointed out that silica retorts are no better as heat conductors than clay retorts, but that they do have a superior rigidity in the furnace. The character of the retorts does not affect the density of the charge. Mr. Neale gave the procedure in the manufacture and use of high-silica retorts at the Donora zinc works, not

Jan 1, 1931

By H. I. Young

Inasmuch as there has been a great deal of activity in this district recently, a paper of this kind should treat of all the various phases of mining, namely, prospecting, developing, and operating. Prospecting .. Where ore is found at a depth of 100 ft. (30 m.) or more, the prospect work is done by churn drilling. Several makes of churn drills are used in this work, both steam- and gasoline-driven machines being used. The drilling is usually started with a 6-in. bit, and the size of the bit is reduced, if necessary, as the hole is advanced. It is general practice to drill from 100- to 400-ft. holes, but this is governed entirely by the location and formation of the ground. In drilling sheet ground, close spacing of drill holes is unnecessary, but in narrow orebodies, the holes are spaced from 15 to 50 ft. (4.6 to 15 m.) apart. Ten years ago, very few assays were kept of the drilling, but during recent years records have been kept very accurately, showing the location, elevation, assays, and also the vertical section of the hole. After the orebody is reached, cuttings are taken every 2 or 3 ft. (0.6 to 0.9 m.) samples being sometimes taken by pouring the water off the cuttings and taking a portion of the coarse material for assay. It has been found, however, that very often the sludge material poured off with the water contains high mineral values. To overcome this, cuttings from each 2 or 3 ft. are put in a container, and, after the water is evaporated, sample for assay is taken by means of Jones samplers. Permanent records of cuttings showing various formations are kept in glass jars or glued on large cards. Drilling at present is costing from $1.25 to $1.50 per foot. In pre-war times, the drilling costs ran from 75c. to $1 per foot. Development After proving property by drilling, shafts are put down to the ore-body. These are usually vertical shafts, either single or double compart-

Jan 1, 1918

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By Mark Sheppard

DURING the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the over- burden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semi- circle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and 800 ft. of 4-in. spiral steel flanged pipe. The connection from the pump

Jan 1, 1938

By Oliver Bololes

UNDER the able leadership of Samuel H. Dolbear, the Committee on Nonmetallic Minerals furnished a program of sixteen papers comprising three sessions. An outstanding accomplishment in technology presented at the first session by Benjamin L. Miller and C. H. Breerwood is the application of flotation to the purification of limestone used in cement manufacture. In place of selective quarrying to provide high-grade raw material, the quarry-run stone is pulverized and treated in froth flotation cells for removal of free silica and mica. Some advantages are cheaper quarrying, more complete utilization of quarry rock, avoidance of purchasing high calcium stone, lower fuel cost and improvement in the finished cement. Paul M. Tyler presented the general subject of milling methods as applied to nonmetal lies. He pointed out the importance of some of the more recent refinements in ore dressing, and urged the need of a wider appreciation of their possibilities. The gypsum industry of Canada was described by L. H. Cole. Crystal growth during the setting process was illustrated by moving pictures. The Coastal Plain and interior salt

Jan 1, 1935

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paver.' The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal. Slurries from eight bituminous coal preparation plants in central and western Pennsylvania have been sampled and examined to determine the amount of recoverable coal in each. Examinations of the samples were made to determine the tons per hour of solids and the gallons per minute of water in the slurry; the size, ash, and sulfur analyses of the solids; and the sink-float characteristics of the larger solids. The extreme fines (—325 mesh material) from one of the samples has been examined further to determine the micron size fractions as well as the ash and sulfur content of the micron sizes. Collection of the Samples: Field trips were made to each of the plants where samples were obtained and discussions held with the preparation engineer prior to sampling. The flowsheet of the plant operation was studied and a time-period selected to obtain a representative sample. At least 20 1-gal samples of total plant bleed-off suspensions were collected at each plant in increments over designated periods belived to be typical of the plant flow Three of the samples were obtained from plants in the Pittsburgh area. Each plant supplied information on the capacity, operating time, type of cleaning equipment used, water and material balances, and auxiliary equipment. From the time required to collect given amounts of slurry and from the amount of solids in the slurry, total solids discharges from the plant were calculated and compared with the plant flow. Ash and sulfur analyses of the total solids were also checked, at some plants, with company figures. In all cases where checks could be made there was reasonable agreement between company figures and those reported here. Analysis of the Slurries: Representative fractions of properly agitated samples were examined in the laboratory to determine the specific gravities of the slurries. The solids and water were separated by filtration to check the weight of each so that the percent of solids in the pulp could be determined. From the resulting data, presented in Table I, it may be seen that the percent solids in the slurries ranges from 2.8 to 39.0 and the amount of solids from 2.61 to 45.61 tph. Size Analysis of Solids: Representative fractions of the slurries were permitted to settle and the clear water was removed by siphoning. The solids were then wet-screened at 28, 35, 48, 65, 100, 150, 200 and 325 mesh. Results of the size analyses are presented in Table 11. These results indicate the extreme variation of sizes and in most cases the degree of fineness of the solids. The amount of —325 mesh ranges from 22.5 to 84.5 pct and the amount of+200 mesh from 8.3 to 69.1 pct.

Jan 1, 1961

By E. J. Duggan

It is a coincidence that the two plants in this country for treating copper ores by ammonia leaching came into existence at almost the same time, that of the Kennecott Copper Corporation at Kennecott, Alaska, in March, 1916, and that of the Calumet & Hecla Mining Co. in July of the same year. The success of both from their very beginning attests the merits of the process under widely different sets of conditions. As would be expected, in the time they have been operating these two pioneers in this field have greatly perfected their methods and improved their technic. The early difficulties inevitably encountered in undertakings of this nature have been largely surmounted and the process may now be considered to be well seasoned and matured. There have been no other commercial plants built in this country and but one elsewhere, the Bwana M'Kubwa in Northern Rhodesia, for the reason that this method of treatment may be employed on comparatively few ores. However, it has certain advantages, some of which are inherent to sand leaching processes generally and some to ammonia leaching in particular. Among these may be enumerated: (1) the avoidance of fine grinding; (2) the small amount of water required; (4) a high-grade product; (5) little likelihood of deleterious gangue constituents and fouling of solutions. It is true that great progress has been made in recent years in the flotation of the ores that come within the province of ammonia leaching. Nevertheless ammonia leaching has its possibilities and these may be overlooked in the present tendency toward the use of flotation for all ores. Probably the chief requisite to its further extension to suitable ores will be a cheap source of steam. Ammonia, the only reagent required, is unlimited in supply, readily transported and the price that is likely to obtain in the future should not make its cost at all onerous. Choice of Method for Kennecott Ores The Kennecott ores are typical limestone replacement deposits. The milling ores have a copper content of approximately 8 per cent in a limestone dolomite gangue. About half the copper occurs as sulfide, mostly chalcocite with some covellite, and the remainder in the form of the two carbonates, malachite and azurite. A comparatively coarse grind followed

Jan 1, 1934

By C. W. Spencer, J. T. Smith

GRAIN-BOUNDARY surfaces are penetrated by a liquid phase when the liquid-solid interfacial tension is less than one-half the tension of the grain-boundary surfaces. Grain growth may occur in the presence of this liquid phase. burke1 reports that grain growth of this nature has been observed in two-phase ceramic systems. He suggests that the presence of a grain-boundary liquid may accelerate or decelerate the

Jan 1, 1963

CYRIL STANLEY SMITH, Chairman CARL E. SWARTZ, Past-Chairman ARTHUR PHILLIPS, Vice-Chairman E. E. SCHUMACHER, Vice-Chairman H. A. MALONEY, Treasurer FRANK. T. SISCO, Secretary 9 West 39th Street, New York, N. 1. Executive Committee 1944 1945 WILLIAM C. ELLIS C. S. BARRETT ALAN MORRIS T. A. WRIGHT KENT R. VAN HORN L. L. WYMAN

Jan 1, 1943