Search Documents

By R. Stratton-Crawley

Flotation-related processes utilizing an oil phase for processing fine mineral particles have been described and various applications discussed. The problems associated with the techniques are varied, but may be summarized by the following areas; (1) applicability to fine particle beneficiation, e.g. collector extender and emulsion flotation. (2) major 'mechanical' problems, e.g. emulsion breakage and oil recovery in oil flotation. (3) complex interfacial chemistry, e.g. empirical nature of pigment flushing .

Jan 1, 1979

By V. Runolinna, R. T. Hukki

Preliminary separation of precious metals by flotation can offer a simplification of the conventional method of treatment of anode slimes. Laboratory flotation experiments show that rich gold and silver concentrate can be obtained with excellent recoveries. THE purpose of this paper is to present the results of an investigation into the possibilities of separating precious metals from anode slimes by selective flotation. The work was carried out at the State Research Institute in Helsinki, Finland. The sample of anode slimes tested was submitted by the Outo-kumpu Co. in Finland. In 1947 the average assay of filtered and dried anode slimes in the Outokumpu refinery in Pori was as follows: Au, 0.50 pct; Ag, 9.38 pct; Cu, 11.02 pct; Ni, 45.21 pct; Pb, 2.62 pct; Fe, 0.60 pct; Sn, 1.00 pct; Sb, 0.04 pct; As, 0.70 pct; Se, 4.33 pct; S, 2.32 pct; SO,, 2.17 pct; SiO2, 2.25 pct. The daily assay naturally varies considerably from the figures presented above. The present conventional method of treatment of anode slimes consists of the steps shown in the flowsheet in fig. 1. As seen from this simplified flowsheet, the present method of treatment involves many steps by which the components of the anode slimes are removed one after another until the main products, gold and silver, may be separated. Due to the small scale of operations, the above procedure is carried out in small batches requiring considerable amount of manual labor. If, however, the anode slimes could be treated in

Jan 1, 1951

By V. Runolinna, R. T. Hukki

Preliminary separation of precious metals by flotation can offer a simplification of the conventional method of treatment of anode slimes. Laboratory flotation experiments show that rich gold and silver concentrate can be obtained with excellent recoveries. THE purpose of this paper is to present the results of an investigation into the possibilities of separating precious metals from anode slimes by selective flotation. The work was carried out at the State Research Institute in Helsinki, Finland. The sample of anode slimes tested was submitted by the Outo-kumpu Co. in Finland. In 1947 the average assay of filtered and dried anode slimes in the Outokumpu refinery in Pori was as follows: Au, 0.50 pct; Ag, 9.38 pct; Cu, 11.02 pct; Ni, 45.21 pct; Pb, 2.62 pct; Fe, 0.60 pct; Sn, 1.00 pct; Sb, 0.04 pct; As, 0.70 pct; Se, 4.33 pct; S, 2.32 pct; SO,, 2.17 pct; SiO2, 2.25 pct. The daily assay naturally varies considerably from the figures presented above. The present conventional method of treatment of anode slimes consists of the steps shown in the flowsheet in fig. 1. As seen from this simplified flowsheet, the present method of treatment involves many steps by which the components of the anode slimes are removed one after another until the main products, gold and silver, may be separated. Due to the small scale of operations, the above procedure is carried out in small batches requiring considerable amount of manual labor. If, however, the anode slimes could be treated in

Jan 1, 1951

By W. C. Phalen

SALT-MAKING PROCESSES THE production of salt in the United States divides itself at the outset into two distinct classes: (1) The mining of rock salt and its purification and separation into marketable sizes, and (2) the production of salt by evaporation from brines, bitterns, and other solutions. The processes employed at the present time in the manufacture of salt by evaporation may be outlined as follows: 1. Solar evaporation. 2. Direct-heat evaporation (a) in open kettles; (b) in open pans. 3. Steam evaporation, (a) in jacketed kettles, (b) in grainers. 4. Vacuum-pan evaporation. In this paper only the solar-evaporation processes practised in different parts of the United States will be described. SOLAR EVAPORATION Localities In the Eastern States the solar-evaporation process is not generally employed for climatic reasons. In the Western States, particularly in California and Utah, the great bulk of the salt produced originates in the solar-evaporation process. Of the Eastern States producing salt, this process, so far as the writer is aware, is employed in New York State only.

Jan 9, 1914

By William P. Dyrenforth

The principle of electrostatic separation is discussed and elaborated on by dividing into the three main mechanisms of electrification as applied to separation of solid substances, i.e., (1) contact electrification, (2) electrification by conductive induction, (3) electrification by ion bombardment. Types of equipment used for electrostatic processing are described and the effects of humidity mentioned. Processing of iron ore, titanium minerals, rare earths and cassiterite is discussed and some existing plants are described.

Jan 1, 1978

By R. W. Brauchli

The author has made a statistical analysis of the relations between recovery and length of cores, diameters of cores and of drill pipe, and cost of coring under different contractual conditions. The data are presented in tabular form. The length of the core appears to play a minor part in the percentage recovered, with a tendency to lower percentages with increased core length; approximately 50 per cent of the length cored is normally recovered if the cores are more than 2 in. in diameter. The diarneter of the core has a more pronounced influence on the recovery; 1 3/8-in. cores average 29.1 per cent, 2 1/8 -in. core 53.4 per cent and 3 1/8-in. cores with 6 5/8-in. drill pipe 68.5 per cent. Where 31/8-in cores were taken with smaller diameter drill pipe, i. e., 4 1/2 - in. drill pipe in 8 1/4-in. hole, the recovery dropped to 49.8 per cent, indicating that the more rigid drill pipe favors good core recovery, a conclusion also borne out by the results obtained in using large drill pipe for smaller diame-ter cores. Surprisingly good recoveries were obtained from both the Johnson and Simpson sands; shale, limestone and dolomite each gave less then average recoveries. No serious fishing jobs resulted from coring operations. Attention is called to the need of a core drill which will make it possible to drill a full-sized hole while coring, and thus reduce the cost of cores. Data pertaining to core drilling should be consistently recorded, such as, diameter of drill pipe and collar, diameter of core, recovery, size of cutter heads, type of core-barrel, coring time, speeds of rotation and of pumps, weight on core-barrel, etc.

Jan 1, 1933

E. K. Landis, Philadelphia, Pa. (communication to the Secretary) : Mr. Firmstone's paper is of great interest; but he has unfortunately otnitted to state the most important point, viz., the percentage of sulphur in the two materials he compares; and this omission vitiates the conclusions which he draws. Comparing by grade, instead of silicon-contents (as in his Table III.), the iron made using limestone with that made using dolomite, we find for gray-forge the average of four analyses under limestone to be, Si, 0.644; S, 0.089 ; while one analysis under dolomite gives Si, 0.508 ; S, 0.070. For No. 2 iron, the limestone flux gives, as an average of 19 analyses, Si, 1.107; S, 0.051; while the average of 4 analyses made with dolomite flux gives Si, 0.630; S, 0.056. It will be observed, that no No. 1 pig is given under limestone, while 14 analyses appear under dolomite, averaging Si, 0.950 ; S, 0.028. As nothing is said about changed conditions, it is Fair to presume that the ore and fuel, as well as the blast-temperature (which is stated to have been uniform at about 750' F.) remained practically the same; and since the sulphur in the two fluxes is not given, it is impossible to know whether the lower sulphur for equal silicon-contents is due to the use of dolomite or to other conditions. The use of dolomite would produce a more fusible cinder, and the furnace would be hotter than when using limestone; therefore, we might expect to see a grayer iron. The amount of So. 1 iron made with dolomite seems to confirm this supposition; and, under these conditions, we might expect more of the sulphur to be volatilized, and to pass off in the gases. The easier fusibility of the cinder would also permit more rapid driving; and this should reduce the amount of silicon and sulphur in the iron, as the amount of reduced metalloids in the pig is directly proportional to the length of time it remains in the reducing-zone.

Jan 1, 1895

By Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodity in this volume has as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as fluxes, glass raw material, refractories, fillers, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Recent. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited availability in certain areas. Limestone and dolomite are so useful and so abundant that in 1981 about 644 million tons were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses, with emphasis on developments since 1960. In doing so we borrowed extensively from our report on the applied geology of limestone and dolomite (Rooney and Carr, 1971). The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired down in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information. Geology Mineralogy The principal carbonate rocks used by industry are limestone and dolomite. Limestones are sedimentary rocks composed mostly of the mineral calcite (CaCO3) and dolomites are sedimentary rocks composed mostly of the mineral dolomite (CaCO3 • MgCO3). Aragonite (CaCO3), which has the same chemical composition as calcite but a different crystal structure, is economically important only in modern deposits, such as oyster shells and oolites. Aragonite is metastable and alters to calcite in time. Some other carbonate minerals, notably siderite (FeCO3), ankerite (Ca2MgFe (CO3)4), and magnesite (MgCO3), are commonly found associated with limestones and dolomites but generally in minor amounts. Because of their similar physical properties, the carbonate minerals are not easily distinguished one from the other. Specific gravity,

Jan 1, 1983

By Alexandre Mitinsky

The theory of elasticity, the science of the strength of materials, and all our calculations regarding engineering structures are based on Hooke's law, that in loaded bodies the deformations are proportional to the load producing them. Without this law it would be impossible to design intelligently engineering structures such as bridges, frames, axles, etc. This being the case, the proportional limit,l that is, the point at which deformation ceases to be proportional to load, is the most important factor in engineering design. Further, the working fiber stress should be fixed in reference to the proportional limit instead of, as is usual, in reference to the ultimate strength. The incorrect use of the ultimate strength instead of the proportional limit in setting the working fiber stress is probably due to two reasons: (1) it is a more delicate operation to measure the proportional limit; (2) it is usually assumed, though incorrectly, that the proportional limit is determined by the ultimate strength. In Germany the poin't at which permanent set first appears is often taken instead of the proportional limit. The two points will coincide if Gerstner's law, that elastic deformations are proportional to the loads producing them both before and after permanent set, is true; and the limit of proportionality and the elastic limit or point of permanent set will both be represented on a stress-strain diagram, by the point at which the line ceases to be a straight line and becomes curved or changes its inclination. It is to be further noted that the difference in definition between proportional limit and elastic limit introduces a difference in methods of determination in the testing laboratory. The German method of determining the elastic limit by alternately loading and unloading the test specimen is a lengthy process and time has in itself a very considerable influence on the results of physical tests.

Jan 1, 1916

By R. H. Hadfield

Professor ArnolD, of the Sheffield Technical School, who has done so much excellent work in metallurgical research, recently produced, with the aid of aluminum, a sound ingot and bar from the purest known Swedish brand containing 99.8 per cent. of pure iron. Table 1. shows the physical quantities of this metal. TABLE I.— Tests of a Sample of Almost Pure Iron Prepared by Professor Arnold from D. v Ewedish Bar, Containing Before Fusion 0.04 Per Cent. of Carbon. I. II.+ III. Series mark,.. 136 1.371F ...... C, 0.07 0.07 Si, 0.04 0.04 8, 0.02 0.03 ...... Analysis, per cent,. .. P, 0.02 0.015 ...... Mn, 0.06 0.07 Al, 003 ............ Fe, 99.76 99.81 ...... Specific gravity,........... 7.863 ...... Original diameter, inches,. .. 0.564 0.798 0.798 Original area, square inches,. . 0.25 0.50 0.50 Limit of elasticity, tons per square inch,...... 18. 3.8 Breaking-load, tons per square inch,. 21. 23. 14.75 Total elongation, per cent., measured on 2 in.,...... 50. 49.25 61. Total reduction of area, per cent.,. 80. 69.60 61.20 Extension at permanent set, per cent.,...... 0.007 ...... silky and Appearance of fracture,. .. . silky i granular in parts.

Jan 1, 1894

By V. N. Krivobor

The study and use of low-carbon manganese steels have been curiously neglected in the general history of developments in alloy steels. Hadfield1 made an extensive study of manganese-iron-carbon alloys about 1886, which culminated in the wide application and use of Hadfield austenitic manganese steel. His alloys were nearly all high in carbon, as compared with the steels discussed in this paper, and he found a marked tendency toward brittleness in the alloys of medium and low manganese content, that is, below 7 per cent. manganese. As a result, there has been a widespread prejudice against the use of manganese steels containing between 1.0 to 3.5 per cent. manganese with comparatively low carbon. Steels of this composition have never been studied adequately in comparison with other alloy steels, and have had litttle use in practice. In a very recent paper by Sir Robert Hadfield2 the following statement appears: 6L... manganese-iron alloys with little or no carbon do not seem to offer any practical employment; they only become valuable in the presence of quite high percentages of carbon, 0.90 to 1.50 percent." The results of the present investigation are so contrary to the findings of Hadfield that the writers feel fully justified in presenting the preliminary report incorporated in this paper. Previous Investigations As early as 1886 the Terre Noire CO.3 in France produced alloys containing up to 2.5 per cent. of manganese, using ordinary low-grade

Jan 1, 1927

By R. F. Mehl, J. T. Ransom

For many years the Metals Research Laboratory of Carnegie Institute of Technology has been concerned with the statistical nature of the engineering properties of steel from an experimental viewpoint, particularly those properties representing ductility.' In the past three years new work has been directed toward evaluating the statistical nature of the endurance properties. It has been shown that both the fracture curve and the endurance limit in fatigue are markedly statistical in nature. The S-N curve (and the endurance limit) of ferrous materials is often determined with specimens which number as few as ten. The common procedure is to test the first specimen at a stress well above the expected endurance hmit. Each succeeding specimen is then tested at a progressively lower stress, until, after five or six tests, a specimen runs ten million or so cycles without failing. Two or three more specimens are then used to find the highest stress at which failure will not occur; the limiting stress determined in this way is called the endurance limit. It has now been found, however, that the variability in the fracture curve and in the endurance limit in heat-treated alloy forging steels is so great that S-N curves must be drawn on the basis of distribution curves which can be appraised only by statistical methods. Two methods have been adopted in this study: (1) straightforward statistical studies of cycles to fracture of a number of specimens at each of a series of stress levels, and (2) a new abbreviated statistical method, known as "staircase testing."2 The latter corisists in testing a series of specimens, one by one, with the test stress for any given specimen automatically

Jan 1, 1950

By Henry S. Washington

I. INTRODUCTION. DURING the last twenty years or so the chemical investigation of rocks has made great advances, and it is now generally recognized that a knowledge of the chemical composition is as essential as that of the texture or mineral composition-if not more so-for the proper classification of rocks and study of their origin and relationships. Rock-analyses have vastly increased in numbers and, what is of greater importance, in quality. New and improved methods permit of greater accuracy than was possible in the early days, and the list of chemical constituents frequently determined has risen from the seven or eight of the greater part of the nineteenth century to twenty or more. Indeed, rock-analyses with determinations of so many constituents are now commonly made by the chemists of the United States and Australia, while in Germany, Great Britain, France, and Italy the rarer constituents are determined more frequently than formerly. As a consequence of this modern, accurate work, it has been discovered that some elements which were formerly supposed to be rare are of wide-spread occurrence and are often present in considerable amount. The fact is further being developed that the elements tend to show certain relations of occurrence or abundance in connection with each other. This is a fact which is applicable to the rarer elements, and which also finds a broad geological and petrological expression in the recognition of petrographic provinces. We are beginning to obtain some definite, though as yet rudimentary, knowledge of the distribution of the elements among igneous rocks. Some of the results along these lines obtained by study of the vast accumulation of analytical data now available are well known to petrologists, while others do not seem to be so gener-

Sep 1, 1908

By Milton T. Pana

Computer techniques now have been applied to the solution of a wide variety of scientific and engineering problems in the mining industry, but generally not in great depth in any one area. In mining, the area covered in greatest depth and with the greatest success has probably been mine planning and to a lesser degree production scheduling. A rather comprehensive review of the literature related to mine planning and production scheduling indicates that contributions in these areas have been geographically, as well as organizationally, widespread. Of twenty-six papers reviewed, eleven were from industry, eight from educational institutions, four from computer vendors, two from the Bureau of Mines, and one from a private consultant. The conclusions that can be derived from the literature are: First, the-state-of-the art has advanced to the point that computing ore reserves and developing mining plans with the aid of the computer is now a routine practice; second, the application of the computer to mine planning problems has markedly improved our ability to estimate ore reserves, more accurately define pit limits, and determine an optimum mining sequence. MINE PLANNING The papers in this section deal essentially with the problem of determining the final pit limits of an orebody and the ore reserves associated with a given pit limit. The problem is probably best described by Soderberg25 and more recently by Reibell. 23. There are two techniques currently being applied to this problem by several mining companies: 1) the multiple-cone technique and 2) the Lerch-Grossman algorithm. The multiple-cone technique is the older of the two techniques and has the advantage of being more flexible, allowing an engineer to easily vary pit slopes in different sectors of the design. The technique can also be used to define intermediate pit contours. The Lerch-Grossman algorithm is appealing in that the final solution is given in the form of a true mathematical optimum. The technique is limited, however, in that the size of the blocks in the orebody model are a function of the desired

Jan 1, 1969

By Samuel S. Wyer

THE installation of the gas-producer power-plant in America has been so unusual that all engineers have viewed it with in¬terest; a large majority, however, regard it with a lack of con-fidence and many with positive distrust. Despite the fact that European engineers have usually been less inclined to take the initiative along experimental lines than are Americans, they have, nevertheless, developed the gas-producer plant to a very high state of efficiency to which they were forced by the neces¬sity of economy in fuel-consumption. The gas-producer power-plant is so common in Europe that engineers as well as the general public regard it with the same degree of confidence that is now universally placed in steam¬plants. Gas-engines, both small and large, are in general use there, and central stations, aggregating several thousand horse¬power, are quite numerous. The fact that gas-producer power-plants have received so little attention in America may be attributed to five conditions:-1', ignorance and prejudice; 2, newness of work; 3, in-

Mar 1, 1905

By George Sachs, J. Spretnak

The process of recrystallization has not as yet been explained satisfactorily. Some definite conclusions could be drawn from recent investigations, such as, for example, that recrystallization is a process of nucleus formation and crystal growth1 and that the orientations of the nuclei correspond to some fragments of the original crystals, which have been considerably distorted during deformation.2 There are, however, a number of metals and alloys crystallizing in the face-centered cubic system, which form a particularly simple orientation if recrystallized as a sheet.3 Such a shect is almost a single crystal with the cubic axes parallel to the rolling, transverse, and normal directions of the sheet. This preferred cubic or (100) orientation of the recrystallized sheet has been considered to be very different from the rolling structure of the same metals,4 but there are two reasons why this last supposition remains open to controversial discussion. The first reason is academic: In practically all cases except the one mentioned above, close correlations and similarities between rolling and annealing orientations have been observed; for instance, in iron and steel sheet.6 Secondly, no deformed metal actually forms a simple orientation. In any thoroughly investigated case a number of different orientations and considerable scattering or deviations from the ideal orientations have been found.6 It is generally true that investigations on single crystals have shown that a definite orientation is approached in stretching or in compression of an originally undisturbed crystal.7 In the special cases, however, where the initial orientation was close to an important crystallographic direction that differed from the final "ideal" orientation, the resulting orientation changed very little by deformation, staying somewhere in the vicinity of the initial orientation.8 Such deviations

Jan 1, 1940

By George Sachs, J. Spretnak

The process of recrystallization has not as yet been explained satisfactorily. Some definite conclusions could be drawn from recent investigations, such as, for example, that recrystallization is a process of nucleus formation and crystal growth1 and that the orientations of the nuclei correspond to some fragments of the original crystals, which have been considerably distorted during deformation.2 There are, however, a number of metals and alloys crystallizing in the face-centered cubic system, which form a particularly simple orientation if recrystallized as a sheet.3 Such a shect is almost a single crystal with the cubic axes parallel to the rolling, transverse, and normal directions of the sheet. This preferred cubic or (100) orientation of the recrystallized sheet has been considered to be very different from the rolling structure of the same metals,4 but there are two reasons why this last supposition remains open to controversial discussion. The first reason is academic: In practically all cases except the one mentioned above, close correlations and similarities between rolling and annealing orientations have been observed; for instance, in iron and steel sheet.6 Secondly, no deformed metal actually forms a simple orientation. In any thoroughly investigated case a number of different orientations and considerable scattering or deviations from the ideal orientations have been found.6 It is generally true that investigations on single crystals have shown that a definite orientation is approached in stretching or in compression of an originally undisturbed crystal.7 In the special cases, however, where the initial orientation was close to an important crystallographic direction that differed from the final "ideal" orientation, the resulting orientation changed very little by deformation, staying somewhere in the vicinity of the initial orientation.8 Such deviations

Jan 1, 1940

By A. Perry Thompson

I- GeneRal Distribution, AppeaRance, and Relations ........ 563 11. Data fRom MicRoscopic Examination............... 568 1. Criteria for Distinguishing Primary from Secondary Minerals...... 568 2. The Leonard Vein Filling..................... 574 Quartz............................ 575 Pyrite............................ 575 Enargite............................ 576 Covellite............................ 578 Bornite............................ 581 Chalcocite........................... 583 Chalcopyrite.......................... 586 3. The Fault-Vein Covellite..................... 587 The Speculator Ore........................ 587 The East Gray Rock Ore.....,.............. 589 4. Other Occurrences of Covellite.................. 591 111. Conclusions........................... 592 1. The Replacement of Minerals..................592 2. The Character of Mineralizing Solutions .............. 594 I. General Distribution, Appearance, and Relations Mining in Butte has seldom encountered covellite in commercial quantities. The notable occurrences, extending vertically and laterally perhaps several hundred feet, presented scattered, bladed lenses of this mineral in a matrix of quartz, pyrite, enargite, bornite, and chalcocite. But under the microscope covellite is seen to be widespread in the Butte ores, though in such small quantity that megascopic examination will not discover it. In early mining operations covellite was found in the Gray Rock vein, a member of the Blue vein system. As described by Sales,' it persisted as an occasional ore mineral, associated with quartz, pyrite, tetrahedrite, bornite, chalcocite, and minor amounts of sphalerite, from the 700-ft. to the 1,200-ft. level of the East Gray Rock and Diamond mines. Crushed quartz-monzonite and later quartz completed the vein filling between

Jan 1, 1916

By John T. Cumberlidge, Frederic M. Chace

Nickel-bearing saprolite developed during the early Tertiary over a northeast trending ultramafic body of Jurassic age near Riddle in southwestern Oregon. The principal nickel mineral is garnierite, but other complex nickel minerals may be present. There are two main ore bodies, an upper (older) one associated with the Klamath peneplain, and a lower (younger) one on the Sherwood peneplain. Saprolite constitutes the bulk of the ore and was probably derived from peridotite and dunite through chemical decomposition by downward percolating meteoric groundwater. Decomposition took place by net loss of MgO, SiO2, and Fe without a change in volume. Faults and joints provided permeable zones which localized saprolite development, and faulting may have helped preserve some ore from loss by erosion. Garnierite-chalcedony boxwork ore was deposited by meteoric groundwater along faults, joints, and at the level of former water tables. Boxwork ore is entirely supergene, the chemical constituents having been derived from higher in the soil profile. The saprolites show evidence of both supergene and residual enrichment in nickel. Red and yellow soil occurs as a capping over saprolite and boxwork, and was derived from them by chemical and mechanical decomposition. The present deposits are probably truncated remnants of a formerly thicker and much more extensive deposit which probably included laterite at the surface. The deposits started to form in the early Tertiary due to deep chemical weathering under sub-tropical to warmtemperature conditions. Early Tertiary ero~ion surfaces of low relief probably contributed to the predominance of chemical weathering over mechanical erosion. Alteration under present climatic conditions favors the formation of soil from saprolite rather than the formation of new saprolite from peridotite.

Jan 1, 1968

By G. K. Manning, P. C. Rosenthal

USE of copper as an intentionally added alloy in steel and cast iron has rapidly expanded with-in the last fifteen years. It is estimated that in 1931 not more than 2000 tons of copper were so used; by 1941, however, this figure had grown to 13,000 tons. Tonnage figures during the war years have been restricted just as copper itself has been restricted, but copper-bearing cast irons and steels have played a part in the production of ordnance equipment. They are used in gun carriages, airplane landing-gear assemblies, scout cars, bulldozing equipment, army trucks, armor plate and many other instruments of war. These wartime applications have their counterpart in many peacetime applications; derricks, dredges, mine equipment, railway equipment, trucks, farm implements, automobiles, and tractors, all usually contain some parts made of copper-bearing steel or iron. An example of this is the Ford tractor which in 1940 contained over 300 lb. of copper-bearing steel castings. To this list should be added corrugated building sheet for exterior use most of which, at the present time, contains upward of 0.15 per cent copper. With the return to peacetime economy and the removal of wartime restrictions, it appears certain that copper cast irons and steels will find increasing application in civilian goods.

Jan 1, 1945