Search Documents

K. T. Aust and J. W. Rutter (General Electric Research Laboratory)—We find it difficult to reconcile the activation energies determined by Gifkins with his general conclusion that "migration during both creep and grain growth can thus be treated on the basis of the same model" (that of Lucke and Detert). Gifkins finds the activation energy for grain boundary migration during creep to be 24.5 kcal per rnol and that for grain boundary migration during grain growth to be 7.5 kcal per mol. The calculation carried out by Gifkins of the activation energy for grain boundary migration during grain growth, using the Lucke and Detert model, gives a value of 20 to 24.5 kcal per mol, rather than his experimental value of 7.5 kcal per mol. The theory of Lucke and Detert was developed to account for the rates of migration of grain boundaries in the presence of impurities during grain growth. The theory does not take into account the effect on the boundary migration of another, simultaneous process such as creep deformation and would be expected, therefore, to be applicable only to migration during grain growth. The fact that Gifkins measured a different activation energy for boundary migration during grain growth (7.5 kcal per mol) from that during creep (24.5 kcal per mol), although the specimens were of the same composition, shows clearly that such an effect exists under his experimental conditions; the presence of a simultaneous creep deformation markedly affects the boundary migration process in comparison with what would be observed under the same conditions but without the creep deformation. The failure of McLean's equation (Eq. [4] of Gifkins' paper) to give a satisfactory dislocation density difference for boundary migration during creep is not surprising, since the activation energy which must be used in this equation refers only to the elementary atom transfer process of grain boundary migration. This activation energy value is approximately 6 kcal per mol for zone-refined lead, as determined in both the grain boundary migration experiments of Aust and Rutter31, 32 and the grain growth experiments of Bolling and Winegard.33 Using this activation energy value, McLean's equation gives reasonable agreement with observed migration rates for grain boundaries moving free of the influence of impurities.31, 32 The value of 24.5 kcal per mol is probably associated with the presence of impurity atoms, as Gifkins suggests. It should be noted, however, that this value was obtained using lead of only one composition and measurements at only two temperatures. The work of Aust and Rutter3"' on the effects of tin, silver, and gold on grain boundary migration in zone-refined lead in the temperature range from 320" to 200°C, as well as the work of Bolling and Winegard34 on the effect of silver and gold on grain growth in zone-refined lead, shows that the measured activation energy is markedly dependent upon the kind and amount of solute present. Gifkins' work does not permit evaluation of the effect of the 8 ppm of impurities other than oxygen present in his specimens. One incidental point: the symbols used to designate the experimental points of Fig. 6 appear to be in incorrect order in the figure caption. As the caption is printed, it would indicate that larger grain sizes were obtained after annealing at 47°C than at 100°C, which does not agree with the text (point M, p. 1019). Finally, it seems clear from Gifkins' results that any serious attempt to determine whether grain boundary migration and grain boundary sliding during creep occur with the same activation energy, as Gifkins suggests and McLean rejects, must take into account the effects of impurities on these two processes, Although the work of Weinberg35 indicated that adding small amounts of copper, iron and silicon to aluminum did not affect the grain boundary shear behavior, it should be noted that his starting material contained approximately 60 ppm of impurities. Gifkins' results indicate impurity effects at an impurity level of 8 ppm, suggesting strongly that the most significant impurity range to be investigated lies substantially below that value. R. C. Gifkins (author's reply) — As Drs. Aust and Rutter suggest, the results under discussion may have to be reinterpreted in the light of their own work on grain boundary migration, which was not available to me when the paper was written. Because of their work, Aust and Rutter attach more importance than I did to the activation energy for grain boundary migration during annealing (7.5 kcal per mol) obtained from a "direct" plot of log-rate against the reciprocal of absolute temperature. At the time it was obtained, this value seemed rather low, although it was similar to the value obtained by Bolling and Winegard.36 It was then, and still is, difficult to accept this value because of the low value of the index in the power law for grain growth, which seemed to indicate the influence of impurities. It was also concluded that the low value of the activation energy might have arisen from the manner of selecting rates of grain growth which were truly comparable at the two temperatures. There were many other indications in these experiments and those on recrystallization during creep3? that an impurity, probably oxygen, was of importance. The model for grain-boundary migration which Lucke and Detert had proposed was an obvious possibility and its use yielded an activation energy for boundary migration during annealing of 20 to 25 kcal per mol.

Jan 1, 1961

By Robert B. Hoy

To maintain a competitive position in the world market in spite of higher domestic labor costs, the U.S. has been forced to the forefront in developing labor saving devices. This has resulted in automation in our factories, mechanization in our mines, and development of faster and more economical methods of transportation. Since World War II the domestic mining industry has suffered perhaps more than any other sector of our economy. When we assisted our allies-and our enemies-to get back on their feet following the ravages of war we were perhaps overly generous in providing funds and technical assistance to develop foreign mining industries that have since become thorns in the side of our own industry. It has become imperative that domestic industry exert its vigor to meet the challenge of foreign competition. While the domestic industry can meet this challenge of foreign competition in part by protective tariffs, quotas and governmental aid, the most effective way is to maintain technological superiority that will reduce manpower requirements and costs and increase productivity. There is this opportunity both in mineral processing and in mining.

Jan 9, 1962

By W. M. Wojcik, R. F. Kowal

Oxygen and sulfur distributions in commercial, 5-ton ingots of killed, medium carbon steel are described. Oxygen distribution is found to vary with deoxidation practice. Irregular distribution of oxygen within ingots makes necessary special precautions in sampling of rolled products for analysis of oxygen. Oxygen distribution is discussed in terms of recently published solidification concepts which had been successfully applied to simpler cases of segregation. These concepts have been found inadequate to explain observed oxygen distributions. Convective movements of the liquid metal, as determined by tracer elements, are shown to be capable of accounting for the observed distributions of oxygen. IN an effort to explore the origin of surface and subsurface imperfections in pierced steel products, a study of oxygen and sulfur segregation was made on ingots cast in open-top and hot-top molds. The results of our previous investigations1"3 have indicated the importance of the location and amount of oxide inclusions in an ingot. Inclusions close to the surface of the ingot have been found to contribute greatly to the formation of imperfections in the surface of finished products. This study of the effects of deoxidation and casting practice on segregation and the resulting oxygen distribution in ingots was initiated to determine the parameters controlling the location of inclusions in an ingot. Segregation of solute elements during solidification of low-melting binary alloys has been studied in the past.1, 5 Formation and growth of inclusions in iron melts have been studied under specific conditions."- In spite of these and other recent studies,10-12 segregation during solidification of commercial, killed steel ingots is not well understood. Consideration of solidification rates, of segregation during solidification of the chill, dendritic, and central zones, and of material balances for the segregated elements has indicated that a simplified theoretical solidification model is not adequate. However, the observed high oxygen contents in localized volumes of the dendritic zone can be rationalized if additional effects of convection currents in the ingots, precipitation, and rapid growth of new phases are considered. EXPERIMENTAL PROCEDURE Steelmaking and Processing. A group of nine killed. medium carbon steel heats having compositions listed in Table I have been studied. The deoxidation and mold practices used were varied to give a wide range of steel oxygen contents. The amounts of aluminum added to the ladle and the ingot casting practices (hot top and open top) were the main variables. The steel was made by a duplex practice in 160-ton tilting basic open-hearth furnaces. All nine heats were top-cast into 24 by 24 in. big end down, fluted molds, to a height between 60 and 76 in., using both open tops and exothermic hot tops. The deoxidation practice and the tapping and teeming details for each heat and ingot studied are given in Tables II and III, respectively. Hot-top practice is indicated by the letter H following the heat designation. Furnace and ladle temperatures were measured by standard disposable-tip, Pt/10 pet PtRh thermocouples. Teeming-stream temperatures were obtained as described by Samways et al.,13 by immersing a Pt/10 pet PtRh thermocouple, covered by a silica sheath, into the teeming stream under the nozzle. The output of this thermocouple was recorded with Leeds & Northrup Speedomax potentiometer. Calibration of the latter thermocouples was based on the freezing point of a pure iron/oxygen alloy (2795°F). The accumulated errors of measurements were within ±10°F. The thermocouple measurements were supplemented in this investigation by continuous recording of a ratioing, two-color pyrometer (Shawmeter), protected from smoke by a blast of clean air within the sighting tube, and calibrated to read with better than ±10°F accuracy. Following teeming of three heats, P, R, and T, tracer elements were added to the steel in the molds to obtain a record of the progress of solidification. As soon as the teeming stream was shut off, a 0.010-in.-thick steel can containing a mixture of crushed standard ferro-titanium and ferro-vanadium (0.05 pet of each alloy element) was plunged into the middle of the steel pool to a depth of 6 in. In about 30 sec no indication of the can or its contents remained. The surface of the open-top ingots solidified in 20 to 30 sec. A study of liquid metal movement and the precipitation of oxides was facilitated materially by use of the tracer technique as titanium has a low distribution coefficient between solid and liquid steel while vanadium has a high distribution coefficient.

Jan 1, 1965

Jan 1, 1969

By Jasper Stuckey

THE object of this paper is to record and interpret field and laboratory observations made by the writers during five years of study of the barite deposits of North Carolina. Deposits of barite are known to occur in three localities in North Carolina (Fig. 1) two of which-the Hot Springs and Kings Mountain -contain material of economic value. The Hot Springs area begins near Bluff, some 6 miles south of Hot Springs, and continues northeast by Stackhouse; a total length of 7 miles. The Kings Mountain deposits lie along a belt that extends from the north end of Crowders Mountain in a southwestward direction, along the east side of this and Kings Mountain, to Kings Creek, South Carolina. The third locality is 3 1/2 miles southeast of Hillsboro, Orange County, a short distance west of the highway leading from Hillsboro to Chapel Hill. It is not known when barite was first discovered in North Carolina, but production from the Hot Springs area began some 50 years ago. The state has never produced large quantities of barite-usually there have been less than three producers-and definite figures are not available, but reasonably reliable estimates indicate a total production of 300,000 tons. From 1901 through 1920 barite mining was on a seemingly prosperous basis and a large tonnage. was shipped from the Hot Springs and Kings Mountain areas. With the depression of 1920 the industry began to decline and production practically ceased in 1926.

Jan 1, 1933

By C. F. Jr. Nagel

THIS paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. HEAT TREATING Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this improvement may be illustrated by the typical properties of duralumin (Table 1). It is essential that the material be in the wrought condition in order to obtain maximum heat-treatment effects.

Jan 1, 1927

M. A. SCHEIL (presented in written form).-Messrs. Franks, Binder and Brown are to be congratulated for the splendid paper that they have presented. We have not made stress-corrosion tests with the cantilever type of specimen which they describe, but it is well known that a uniform stress across a certain portion of the gage length can be obtained with such a specimen. This type of specimen would appear quite expensive to make. The writer was interested in the authors' remarks concerning the erratic results obtained from specimens with cold sheared edges. It might be of general interest to record here some results we obtained with annealed sheet N4 in. thick of type 304 stainless steel. After specimen No. 4 had been exposed 65 days without any signs of cracking we applied a strain gage and measured the stress as 25,810 psi. This value is considerably higher than we find for some of the type 347 stainless alloys and suggests that 18-8 might have a different threshold value for stress-corrosion cracking than 18-8 columbium. The test data in Table I show that strain caused by cold work or polishing has a pronounced effect in lowering the time for failure. In my paper I showed values of 8 hr. and 17 hr. to stress crack cold-rolled type 301 stainless steel stressed beyond the yield point. This steel contained 8.31

Jan 1, 1945

By G. C. Rauch, T. H. Courtney, J. Wulff

The superconducting behavior of Nb-Ti alloys containing 40 and higher wt pct of Nb and variable oxygen content was studied as a function of thermomechanical processing. Critical current density (Jc) us applied transverse magnetic field (H) data were obtained for 0.010 in. diam wires at 4.2° Kin steady fields up to 120 kOe. The precipitate responsible for increase in Jc in each of the alloys studied was related to niobium and oxygen content. In alloys containing 40 to 60 wt pct Nb with less than about 1600 ppm of oxygen, w precipitation in the range 350° to 450°C appears to be responsible for the maximum value of Jc observed. In alloys of higher oxygen content (-2500 ppm), the oxygen-enriched a phase which precipitates in the temperature range 450° to 550°C is a more effective fluxoid pinner. Maximum Jc in low oxygen (350 ppm) 80 wt pct Nb alloys was achieved by 600°C aging heat treatments. Measurements of resistive critical field also reflect the changes in composition accompanying precipitation in these alloys. It is well known that the superconducting critical current density, Jc, of solid solution superconducting alloys can be increased by precipitation heat treatments.1-4 The precipitate, to serve as an effective superconzlucting fluxoid pinner and increase Jc, must be of proper size and spacing.' Its electronic properties must also be different from those of the matrix.6 As in age-hardenable systems, optimum temperature and time of aging are dictated by the composition and history of the particular solid-solution alloy under consideration. The alloy diagram of Ti-Nb7-9 shown in Fig. 1 is typical of ß-stabilized Ti alloys. Precipitation to achieve high Jc in Ti-Nb and Ti-Ta alloys is usually carried out in what is believed to be a two-phase a + ß region.1,2,4,10 Previous work on Ti-Nb4,11 and on other ß-stabilized systems such as Ti-V, Ti-Mo,12-14 has shown, however, that the first precipitate to appear is not necessarily (Y. Under specific conditions the meta-stable w phase is precipitated instead. A further complication arises in such alloys from the strong influence of contained oxygen on the phase stability and on the kinetics of precipitation.15,16 The superconducting critical current density of Nb-Ti alloy containing less than 36 wt pct Nb has been studied by Vetrano and Boom1 and Kramer and Rhodes.4 The most effective aging temperature was found to be about 425°C; fluxoid pinning was attributed to the precipita- tion of a by Vetrano and Boom and of w by Kramer and Rhodes. Although the latter workers used recrystal-lized material and the former cold-worked, studies carried out in our laboratory lead us to believe that the type of precipitate responsible for increased Jc is unaffected by prior cold-work.17 That other types of precipitates may also be effective, especially in higher oxygen-containing alloys, has been demonstrated by Reuter, et al.2 in this laboratory with the aid of electron microscopy. Reuter et al. found that at an aging temperature of 600°C, fee-TiO is precipitated, resulting in high values of Jc. Even higher values of Jc were observed after heat treatment at 500°C, but the precipitate could not be indexed as fee-TiO. Whether the precipitate was oxygen-rich w or a could not be clearly distinguished. The work nevertheless indicates that appreciable amounts of oxygen alter the nature of the phases precipitated at different temperatures, at least in alloys containing more than 36 wt pct Nb. Since such compositions are more readily worked into suitable wire than lesser niobium content alloys, it was decided to study the response to aging of the alloy compositions reported in the present paper with the hope of clarifying the effect of composition on the precipitation processes responsible for high values of Jc. I. EXPERIMENTAL Nb-Ti alloys containing 40, 50, 60, and 80 wt pct Nb were prepared by are-melting 35 g ingots of iodide crystal bar titanium and electron-beam melted niobium.

Jan 1, 1969

By David R. Maneval, W. E. Foreman, J. Richard Lucas

INTRODUCTION The objective of this chapter is to inform the industry, as well as the public, of the challenges in dealing with the problems associated with the contamination of air and water from coal preparation plants. The need for an informed industry is most important. It is hoped that some contribution may be given to a more efficient and economical approach to the problems of plant waste contaminants at individual plants. The problem has many facets, and consideration to specific area should begin early before any significant problems develop at a given plant. It is then possible to have a reasoned approach before the pressures of an emergency environment force hasty and incomplete solutions. It will be necessary to anticipate these problems in the design of new preparation plants and advance consideration should be given to all the problems concerned with contaminants. The first part of the chapter will concern itself mainly with the contamination aspects of fine-coal cleaning and "black-water" disposal. Also attention will be given to the nature and formation of water from coal-mine drainage systems and the treatment of these waters for industrial use. Some attention will be devoted to the cost of installing and operating the various beneficiation systems for the removal of suspended solids. The second part of the chapter will analyze the problems of air contaminants from coal preparation plants. The nature and the effects of these contaminants and their potential for air pollution will be examined. One of the most critical is the measurement and analysis of these contaminants. As a result of identifying and determining the extent of the problem, better control can be planned. One of the most serious contaminants in air involves the element sulfur, and its elimination as a source of air pollution is one of the most challenging areas in coal preparation today. The last part of the chapter will emphasize the long-range problem of refuse disposal and control. Minimum operating and maintenance costs are functions of the proper selection and geometry of refuse disposal areas. Disposal procedures are varied but must be rigidly pursued or difficulties will result. Maintenance of refuse areas, including monitoring of burning refuse, is critical. It should be recognized that fine-solid refuse disposal systems must be carefully designed to minimize contamination. WATER CONTAMINANTS FROM PREPARATION PLANTS Pollution Aspects of Fine-Coal Cleaning and "Black-Water" Disposal The effluents from coal washeries and waters draining from plant-site surfaces inevitably contain fine coal and coal refuse materials in suspen-

Jan 1, 1968

By Thomas L. Kesler

The Cartersville mining district, 35 miles northwest of Atlanta, Ga, has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. However, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magnesian limestone. General Geology Geologic relations of the ore deposits of this district are more or less similar to those of many Appalachian districts. The lowermost Cambrian formation, heretofore called Weisnerl in this region, supposedly partly or. wholly equivalent to the Erwin and Hesse quartzites as recognized to the northeast, is overlain conformably by the Shady† formation, also of Lower. Cambrian age. In the Cartersville district, the sedimentary rocks of these formations were folded with increasing intensity eastward, and were recrystallized.

Jan 1, 1941

By Thomas L. Kesler

The Cartersville mining district, 35 miles northwest of Atlanta, Ga, has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. However, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magnesian limestone. General Geology Geologic relations of the ore deposits of this district are more or less similar to those of many Appalachian districts. The lowermost Cambrian formation, heretofore called Weisnerl in this region, supposedly partly or. wholly equivalent to the Erwin and Hesse quartzites as recognized to the northeast, is overlain conformably by the Shady† formation, also of Lower. Cambrian age. In the Cartersville district, the sedimentary rocks of these formations were folded with increasing intensity eastward, and were recrystallized.

Jan 1, 1941

By T. A. Wilson, S. L. Hoyt

THE plastic deformation of slender single crystals of zinc has been described in some detail in the paper by Mark, Polanyi and Schmid,1 which has become a classic, and also by one of the present authors in a somewhat shorter account.' The study of single-crystal zinc is termed classical because zinc single crystals offer, perhaps, the best material yet available for the study of atomic behavior during deformation and the effect known as "strengthening" in metals. A considerable amount of additional work has also been done on single-crystal zinc, but as it is not closely related to the present paper it will not be considered. Throughout all the former work, the mechanism of plastic deformation first described by Mark, Polanyi and Schmid has been assumed to hold. This may be said to offer the strongest confirmation of its correctness. Even so, the picture of the process has never been as completely portrayed as is desirable. The first object of the present paper is to describe work that has been done in this field, and which is even yet being carried on, in the hope that a more complete picture may be obtained. Mathewson and Phillips' have recently described a new mechanism of the deformation of zinc based on their study of large rectangular crystals. One of their conclusions was that deformation produced twinning with a rotation of some of the basal planes into positions 94° removed from their original position; a position almost the same as that of the prismatic planes before twinning. A second conclusion was that fracture occurred along these basal planes in their new position, and, therefore that fractures previously regarded as prismatic were in reality basal. Such findings are of great significance and they raise a question as to the generality of such behavior. Professor Mathewson's opinion is that even the slender cylindrical single crystals behave in the same manner as his large rectangular crystals when strained by simple tension.

Jan 1, 1928

By W. S. Keyes

The State of Nevada, known par excellence as " the Silver State," occupies the major portion of the wide plateau, or so-called Great Basin, lying between the Sierra Nevada range on the west and the Wahsatch range of the Rocky Mountains on the east. It extends from the 114th degree to the 120th degree of longitude, west of Greenwich. It is limited, on the north, by the 42d degree of latitude, and on the extreme south by the 35th degree of latitude. Its general shape is that of an irregular parallelogram, from which the lower or southwestern portion has been cut off by a diagonal southeasterly line; the missing portion forms a part of the State of California on the west. The Great Basin is made up of a succession of low hills, or minor mountain ranges, running very nearly north and south, with long valleys between them. All of these mountains are more or less metalliferous. On the westcrn rim, marking the eastern flank or foothills of the Sierra, we find granites, porphyries, and propylites. Here we note the great Comstock lode, with its free-milling gold and silver ores, and still further south the once prominent and the now reviving gold and silver-bearing districts of Esmeralda County, Nevada, and of Morro County, California. Next, at some distance to the east, we find the mining districts at and near Unionville, in Humboldt County. Still further to the east we find the Battle Mountain copper-silver district, north from the railroad, and southerly therefrom the Austin or Reese Ever, Belmont, and other districts. Still further east and north of the railroad, we find the Tuscarora, a new district of very

Jan 1, 1879

By Hjalmar Sjögren

Introduction.............767 Group I. The Ores of the Archean Crystalline Schists.... 770 Distribution............. 770 The Rocks.............770 Structures............772 The Rocks of Norrbotten..774 The Ores.............775 Type A. Apatite.Ores..........776 Type B. Mixed Hematite and Magnetite..777 Type C. Quartz-Banded Ores....777 Type D. The "Skarn" .Ores l..778 Type E. Limestone-Ores,..779 The Origin. of the Ore-Deposits......... 779 Arguments against the Sedimentation Theory,... 780 Concentration and Transformation within the Deep-Seated (Ana-morphic) Zone........783 The Chemical Changes.......784 Transformations in the Surface.Zone....789 The Graingesberg and Norrbotten Deposits,.....791 Analogous Deposits........794 Group II. The Ores of the Porphyries (Keratophyres) ... 796 Kiirunavaara. Luossavaara and TuoIlavaara....797 The Syenite.........799 The Porphyry of the, Foot. Wal1 .....799 The Porphyry of the Hanging-Wal1 ....799 The Ores.........800 The Forms and Dimensions of the Ore-Bodies ..802 Contact-Zones........803 The Genesis of the Deposits .......804 Mertainen and Painirova.......806 Ekatrömsberg..........808 Analogous Deposits,........808 Group 111. Magmatic Seregations in Basic Eruptives,... 809 Taberg in Smaland,.........811 Segregations in Diabase Younger than the Dala Sandstone, . 814 Iron-Ore in Nepheline. Syenite.......815 Ekersund and Soggendal in Norway......816

Jan 1, 1908

By C. G. Rhodes, D. Kramer

The kinetics of precipitation of transient a phase during the transformation in U-16 wt pct Mo between 400° and 550°C were studied using quantitative metallography and electrica1 resistiuity measurements. The volume percent of a phase goes through a maximum in time, corresponding to a critical degree of progress of y' formation. prior to its re-solution after prolonged annealing. The fastest rate of a precipitation oc-cuvs at 500°C with a concomittant lowest peak of 9.5 vol pct a. At 450°C, 14 vol pct a, greatest fov any temperature, was observed after 24 hr witlz an associated slowest rate of formation. a precipitation at 400°C ceases after approximately 160 hr and the amount of a present remains unchanged after long times at temperature; no y' was observed metallographically at this temperature. IN the U-Mo system at 16 wt pct Mo, an ordering reaction takes place below 600°C, see Fig. 1, whereupon the random bcc solid solution, y, transforms to the ordered bct phase, y'."2 The new unit cell is constructed of three old unit cells somewhat distorted. While attempting to study the kinetics of this transformation it was observed that an unexpected phase was precipitating out early during the transformation anneal reaching appreciable amounts before disappearing after long times. The y' appeared in the presence of this new phase and after long times constituted the whole sample. Owing to the high optical activity of this unexpected phase under polarized light, it was suspected to be the a phase. Subsequent X-ray powder pictures confirmed this belief. The kinetics of a phase formation and disappearance is the subject of this paper. EXPERIMENTAL PROCEDURE A) Alloy Preparation. Alloys for this study were prepared by vacuum induction melting normal reactor grade uranium and 99.5 wt pct Mo pellets in thoria crucibles. Two ingots were prepared, and sections of the top and bottom of each ingot were chemically analyzed for uranium and molybdenum content. The results of the analyses appear in Table I. B) Metallography. Samples of 16M were wrapped in tantalum foil, sealed in evacuated (5 X 10"6 mm of Hg) quartz capisules, and annealed at 1110"C prior to being transferred directly to the transformation temperature. They were examined metallographically after increasing times to determine the progress of the transformation at 400°, 450°, 500°, and 550°C. The samples were prepared for metallographic examination by mechanical polishing with diamond paste and electrolytic polishing with a solution of glacial acetic acid and chromic acid. Since the y' phase is tetragonal, its presence can be detected by viewing the sample in polarized light. To increase the contrast between y' plates, the samples were electro-etched in a 10 pct oxalic acid solution. To reveal a phase in bright field (it can be seen in polarized light in the "as-polished" state), the samples were electro-etched in a solution of citric acid and nitric acid. To determine the vol pct a phase, a variation of the one dimensional systematic point count method as described by Hilliard and cahn3 was used. The

Jan 1, 1962

By C. G. Dunn, J. L. Walter

Either (100) (001] or (110) (0011 oriented secondaries, or both, depending on annealing atmosphere and material composition, grew in a matrix of 2-dimensional grains. The growth dependence of secondaries of(hkl) orientation in the iron and 0.6 pct Si-Fe is explained in terms of surface energy driving forces and the dependence of these driving forces on both (hkl) orientation and amount of oxygen at the surace. (100) [001] grains grow when suflicient oxygen is present at the gas-metal interface to make y100 the lowest (hkl) surface energy. When little or no oxygen is present at the gas -metal interface, making Y110 the lowest surface energy, (110) (001 1 grains grow. When Y100 and y110 are approximately equal but lowest among (hkl) surface energies, both (100) (0011 and (110) (0011 grains grow simultaneously. An excess of surface oxygen produces complete grain growth inhibition in high-purity iron; i.e., a 3-dimensional grain structure is retained over long annealing periods. However, a small amount of silicon in the iron reduces the growth inhibiting tendency of oxygen without altering the (hkl) surface energy relationships. Some information on annealing twins is presented. SECONDARY recrystallization in high-purity a iron, cold rolled to strip a few mils thick, was reported recently.' The present paper provides additional information on this subject, also furnishes similar information on both zone-refined iron and a high-purity 0.6 pct Si-Fe alloy, and treats the more important surface phenomena that determine to a large extent whether one or more secondary recrystallization textures will appear during annealing. Previous studies on high-purity 3 pct Si-Fe2,3 have shown the importance of (hkl) and impurity-atom dependent gas-metal surface energies on the formation of secondary recrystallization textures in high-purity material. For example, either (100) or (110) oriented grains may have the lowest surface energy depending on the amount of oxygen at the gas-metal interface, and hence the highest driving force for growth if other growth factors are the same. Another important phenomenon in high-purity material is stabilization of the matrix structure; neither impurities nor a strong matrix texture seem to be necessary when recrystallization and normal grain growth occur, developing a stable two-dimensional type grain structure. The average grain size in such a structure is usually between one and two times the specimen thickness. Consequently, most of the grains have grain boundaries terminating at exposed surfaces, and this results in gas-metal interfaces (or hkl surfaces) as well as

Jan 1, 1962

By G. S. Hume

IN THE autumn of 1922, British Petroleums Ltd. found oil of 14° Baume in a sand 17 ft. thick in its No. 2 well at Wainwright, 120 miles southeast of Edmonton. This greatly encouraged drilling in the Wainwright-Irma area and this past summer several wells were started, three of which are now completed' and the others still being drilled. Of the three completed, No. 4 British Petroleums contains oil; No. 3 British Petroleums gave a show of oil but so far has not given much hope of becoming a commercial producer; and No. 1 Maple Leaf Co., as now finished, is a gas well with a daily flow of gas of about 2,500,000 cu. ft. at a closed pressure of 700 lb. An oil sand is reported . to have been encountered below the producing gas horizon, in the Maple Leaf well but has not been tested. Operations on this well have been suspended for the winter. The Geological Survey of Canada this past summer undertook a geological investigation of this area with the object of defining the structures with which the oil and gas are associated. The 'structure underlying this portion of the plains was supposed to-be a terrace with the western edge dipping into the Alberta syncline and with a monoclinal structure to the east. By accurate leveling on known geological horizons on this terrace, a number of gentle folds were located and it is in these folds that the oil land gas are found. At the British Petroleums Nos. 2-and- 4 oil wells, the western flank of the fold has a gentle dip of only a few feet to the mile to the southwest whereas the strata on the eastern flank dip to the northeast about 40 ft. in 1/2 mile, the strike of the fold being northwest and southeast. How far oil will be found down the gentle southwest dip is unknown but probably the productive part of the fold will not exceed 1 mile in width, and possibly less. No. 3 British Petroleums well is on the strike of the fold 1 mile southeast of the two oil wells. The sand that was productive in Nos. 2-and 4 wells was not present in this well or, if present, was very thin and unproductive. Two other sand horizons, however, were encountered. The upper of these

Jan 3, 1925

By W. W. Wirth

RESEARCH looking toward the reduction of the cost of roof support by substitution of longer-life materials for wooden timber is fully justified by the fact that roof support is an important element of all production costs. Permanent or semipermanent roof support will reduce the expense of timber-maintenance crews during steady operations, but even more markedly during idle periods. The management, therefore, is faced with the important problem of timber renewals, which in times of regular operation are frequently obscured by more urgent problems of production. Increased use of timber in the Anthracite Region of Pennsylvania is caused mainly by increased percentage of coal obtained from robbing areas, which requires more timber for safety than develop-ment work, and maintenance of long haulageways through crushed ground despite the fact that less coal is transported over them. The timber reserve in the immediate vicinity of the mines has been depleted to such an extent that it is necessary to secure 70 per cent of the timber requirements from distant sources. Originally, mine timbering in this region was done by largely utilizing round props or legs with round collars. The whole cross section of the tree from which timber was cut was utilized by forming the joints between the legs and the collars with saw and adze, using plank or round saplings for lagging behind the legs and over the collars to prevent material falling between them. The Mine Inspectors' report of 1898 records an important digression from the use of round timber, when two tunnels at the Babylon colliery, near Pittston, Pa., were timbered with 12 by 12-in. square timber sets with mud sills, through quicksand for distances of 425 and 160 ft., respectively. The timbers were lagged with 3-in. plank to control sand.

Jan 1, 1940

By R. G. Bowman

Discussions of processes for the manufacture of white lead generally open with the statement that white lead is the oldest chemical pigment known to man. This fact is of more than historical interest; in the light of the present extensive use of white lead, it indicates that the compound possesses characteristics that make it unique among white pigments, and superior to all in its particular field. A greater variety of processes have been proposed for manufacturing white lend than for any other one chemical compound. Only a few of these processes have come into commercial use, however, and a large part of the present production here and abroad is made by the process used in ancient times. The outstanding disadvantages of the old process are that it is slow and laborious, affords no control of the product, and yields at best an impure material lacking in uniformity. Improved processes, sometimes classed all together as "quick processes," have had as their main object the shortening of the time required. Most of them accomplish this and some have yielded a superior product as well, but only two or three are now in use commercially. For centuries the manufacture and mixing of paints have been treated as an art, and the practice has been much influenced by tradition and precedent. There is a reluctance to abandon old materials for this purpose, and as few new uses for white lead have been developed, the adoption of the quick processes has been slow. The electrolytic production of white lead is not new, a large number of processes and forms of apparatus have been proposed and patented within the past 25 years, all directed toward the production of white lead, wholly or in part, by electrolysis. One or two of these processes were tried commercially but proved unsuccessful. Process The Sperry process, used by the Anaconda Lead Products Co., is the invention of Elmer A. Sperry, and was worked out to a commercial basis at the East Chicago plant. It resembles, in a general way, earlier methods, but embodies the features that make it possible to operate

Jan 1, 1926

By George B. Langford

ON THE QUESTION of postwar controls there are today three schools of though ; some advocate state control of everything the socialists ; second are those who advocate the removal of all governmental control over industry - the freedom of enterprise ideal ; and third are those who advocate a middle course - sufficient control to stabilize economic and industrial life, and to prevent violent fluctuations such as we saw in the interwar years. I advocate this third course. I firmly believe un free enterprise, but not in freedom of enterprise, or laissez faire, and there is a great and significant difference between these two.

Jan 1, 1944