Search Documents

By H. Conrad

The strain hardening associated with the creep of magnesium single crystals at room temperatu.Je was investigated by shear tests in which the direction of stressing was reversed a number of times after creep in a <100> direction. The strain hardening was strongly anisotropic; the largest amount occurring in the direction of flow and the least 180 deg to this. The time law for creep changed from a parabolic type to logarithmic for the first and subsequent reversals of stress. For a given stress the creep strain decreased significantly for the first and second reversals and then only slightly for subsequent reversals. The logarithmic creep constant a changed in a similar manner. A linear relationship was observed between the creep strain for a given reversal and the stress. The slope for the third reversal yielded a strain hardening coefficient 12 to 16 times greater than that observed for unidirectional flow. Al-though no recovery was observed upon resting at room temperature, the hardening resulting from stress reversals could be completely removed by heating to 450" C. PREVIOUS work1.&apos; indicated that the creep rate of magnesium single crystals tested in the temperature range of 78" to 364°K decreased with time. This was attributed to an increase in internal stress resulting from an accumulation of dislocations at internal obstacles. The object of the present investigation was to further evaluate the nature of this hardening by conducting tests in which the direction of stressing is changed after previous creep in shear in a given slip direction. Previous to 1950 three investigations indicated that a Bauschinger effect3 occurred for single crystals as well as polycrystals brass in tension compression,

Jan 1, 1960

Jan 1, 1963

By W. B. Tucker

UNUSUAL interest has recently centered in the Mojave mining district of California, owing to new discoveries of gold ore at the Silver Queen mine, and subsequently at other neighboring proper- ties. These finds have proved that opportunities exist for the prospector even in old mining districts, where careful search may still be rewarded. The Mojave district is characterized by a group of small hills centering around Soledad Butte, four to six miles southwest of Mojave, in Kern County. This butte is 1250 ft. higher than the surrounding desert and 4000 ft. above sea level. Four miles west of Soledad Mountain are the so-called Middle Buttes, a group of flat-topped hills. Gold was first discovered in the district in 1894, and the following productive mines developed: Queen

Jan 1, 1936

By John T. Crawford

Introduction Loading and hauling systems are evaluated in open pit mining for new properties, expanding existing operations, changing systems or equipment, and equipment replacement analysis. The objective of such evaluations is to determine the equipment needed to handle planned tonnages at the lowest cash flow cost. Cash flow costs are used to combine capital outlays with operating and maintenance costs. Leasing costs could be substituted for capital costs with appropriate modifications to calculation procedures. These modifications will not be covered. This chapter will describe methods of evaluating loading and hauling systems, concentrating on some of the more often raised questions concerning quantitative data. While the methods described are not the only ones in current use, they have a record of proven reliability. The shovel and haulage truck system is used In the examples because of its common use in open pit mines. In medium to large open pit mines, electric shovels and diesel-electric drive haulage trucks are normally used. The basic ideas presented in this chapter apply to all loading and hauling systems, with appropriate modifications. The process of performing a shovel and haulage truck evaluation can be time-consuming and tedious because of the quantity of data involved, but it is not particularly difficult. The examples used to Illustrate shovel and haulage truck evaluation are based on a hypothetical open pit mine operating 350 days per year producing 31 750- 000 t (35,000,000 st, 100,000 stpd) annually, of which 11 110 000 t ( 12,250,000 st, 35,000 stpd) are ore. Selection of the optimum shovel and haulage truck fleets will be shown. The principal sources of data for the examples or any other equipment evaluation are equipment manufacturers and actual operations. Whenever possible, actual operating experience should be used to verify estimates. The quantitative data presented herein are unrelated to a specific existing mining operation.

Jan 1, 1979

By Robert Sisselman

Central Sweden&apos;s Grängesberg underground iron ore mine, which accounts for more than three million tons of pellet product annually, is experiencing a major changeover to continuous block-caving. The newly-adopted method, complete with a total revamping of mining equipment, will be fully operational by 1975. For the past 15 years, Sweden&apos;s Grängesberg mine has been mined using two different methods. Those ore thicknesses of 117 ft or greater (they comprise about 70% of the total area) are worked by block-caving techniques with cross-cutting carried out on each 195-ft working level, and loading at the foot wall on each 58-78-ft level. Sub-level caving is carried out in all ore sections less than 117 ft thick.

Jan 1, 1974

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

By H. J. Engell, W. Frank, A. Seeger

SWISHER and ~urkdogan&apos; have determined the solubility of oxygen in a iron. They found it to lie between 7 and 10.5 at.-ppm at 881°C. Using earlier work on the permeability of oxygen in bcc iron,&apos; they arrived at the following expression for the diffusion coefficient of oxygen in bcc iron (k = Boltzmann&apos;s constant, T = absolute temperature): where The present authors3 have estimated the activation energy QD for the diffusion of oxygen in bcc iron in two different ways from various experimental data.2&apos;4"6 In the first method QD + QS (QS = heat of solution for oxygen in bcc iron in thermodynamic equilibrium with solid FeO) was determined either from data on the reduction of FeO with hydrogen4 or from measurements of the internal oxidation of silicon in a iron.5 Using an estimate of QS from investigations of the oxygen solubility in 6 iron2 (in thermodynamic equilibrium with molten FeO) Q = 0.97 ev or Q~ = 1.06 ev were obtained. From the magnitude of these values it was concluded that oxygen migrates interstitially in bcc iron and that consequently the activation energy QD for diffusion of oxygen has to be identified with the migration energy E~ of the oxygen atoms. Therefore, for a second estimate of QD from the diffusion coefficient of oxygen in 6 iron at 1450" ~,~ we used the theoretical expression:3 (a = length of elementary cube edge, m = mass of interstitially diffusing atom, sM = migration entropy), applicable to diffusion via the octahedral interstices in bcc lattices. Taking sM = 3.8 k (migration entropy of carbon in a iron), one gets Q = 0.90 ev. Hence, in Ref. 3 Q = (0.98 *0.1) ev was proposed as a plausible value for the diffusion energy of oxygen in bcc iron. sM + 9 (9 = solution entropy for oxygen in bcc iron) can be determined from permeability measurements.4 Using the above-mentioned estimate for QS , the following expression for the solubility c (atomic concentration) of oxygen (in thermodynamic equilibrium with solid FeO) in bcc iron was derived: From [4] the solubility of oxygen at 881°C in a iron is calculated to lie between 0.6 and 12 at.-ppm. We see that the solubility determined by Swisher and

Jan 1, 1969

By Donald C. Myntti

Modern open-pit mining can be described as a capital-, labor-and energy-intensive, large-scale, mechanized, and highly repetitive bulk material preparation and handling operation, with emphasis on the word "mechanized." In hard rock, this generally means shovels loading blasted materials into haulage units for transport to processing plants, stockpiles, or waste dumps. Mine management deals with several primary concerns on a daily basis; e.g.: Will any serious accidents and labor problems occur today, and will the tonnage targets be met considering the physical condition of the equipment? The latter subject will be discussed from a maintenance perspective. A successful, progressive heavy equipment maintenance program that protects company assets involves many elements. They include: •Proper equipment selection and procurement •Well-trained and motivated workforce •Good shop facilities •Preventive maintenance (PM) program •Warehouse support •Operations-maintenance department cooperation •Meaningful paperwork

Jan 3, 1978

By AIME AIME

American Institute of Mining Engineers. (Organized in 1871, and Incorporated in 1905.) OFFICERS. For the year ending February, 1906. Directors JAMES GAYLEY (President), R. W. RAYMOND (Secretary), FRANK LYMAN Treasurer). T. A. RICKARD NEW YORK, N. Y. CHARLES H. SNOW NEW YORK, N. Y. R. W. RAYMOND NEW YORK, N. Y. (Terms expire February, 1906.) JAMES GAYLEY NEW YORK, N. Y. FRANK KLEPETKO NEW YORK, N. Y. FRANK LYMAN NEW YORK, N. Y. (Terms expire February, 1907.) JAMES DOUGLAS NEW YORK, N. Y. JAMES F. KEMP NEW YORK, N. Y. ALBERT R. LEDOUX NEW YORK, N. Y. (Terms expire February, 1908.)

Jan 1, 1906

By Ellsworth Daggett

THE system of pitwork used with the Cornish pumping engine, and which, for want of a better name, we may call the Cornish system of pitwork, consists essentially of a series of plunger-pumps, situated one below the other, in a shaft or incline, the plungers being operated by a rod called the pitman or pump-rod, which must, therefore, extend from the motor at the surface to the lowest pump. The subject will be best understood by reference to Fig. 1, in which k may be taken as typical of the ordinary plunger-pump, in which S is the suction pipe, u, the lower valve situated in the H piece T; v, the upper valve situated in the valve-box O; I, the mounting-pipe or column through which the water is carried to the surface; L, the plunger-barrel, and P, the plunger working through the stuffing-box, and actuated by the branch rod r, which is attached to the main pump-rod, R. The action of the pump is as follows : On the ascent of the plunger, acting now by suction, the water flows from the reservoir through the valve u, into the barrel, L. On the descent of the plunger, the water is forced up through the valve, v, which acts merely as a check valve, into the pipe, I, through which it is, at each successive down-stroke of the plunger, forced upward until it reaches the next reservoir, from which it is taken by another similar pump, and so on until it reaches the surface or drain-tunnel. The pump is obviously only single-acting, i. e., it acts only during one-half of its entire stroke. The weight of water raised during the up-stroke of the plunger is equal to the weight of a column of water whose base is the area of the plunger and whose height is the mean distance between the plunger-face and the surface of water in the lower reservoir, a distance not usually exceeding 12 or 15 feet, and which obviously cannot under the most favorable circumstances, exceed 25 or 30 feet. The water forced up during the down-stroke is equal to the weight of a column of water whose base equals the area of the plunger and whose height equals the length of the mounting column above the mean position of the plunger-face, say from 150 to 300 feet. Almost all of the useful work, therefore, is done on the de-

Jan 1, 1879

By Joseph Jensen

MANY fields have been zoned by nature with shales and intermediate waters between oil zones. Limitations thus imposed have been the basis on which the field was developed. In contrast thereto, in the Ventura Avenue Field, nature proved more generous. Always expecting to find such similar limitations, operators drilled deeper and deeper into the oil zone without finding any distinctive shale bodies other that the Gosnell shale and only one intermediate water, which became the point below which the final water shut-off of each well was made. Thus, on top of the structure, about 3300 ft. of oil-bearing zone has been penetrated below this intermediate w9ter-a distance of 4000 ft. below the Gosnell shale. At first it seemed that the greater the penetration in the zone, the better the well. The error of this assumption became evident

Jan 1, 1930

By R. W. Smith

Many industries such as the cement industry handle large quantities of limestone and clay slurries. However, at present very little is known about the flow properties, such as friction loss due to flow of slurries in pipelines. This lack of knowledge has made it often very difficult to calculate the total dynamic head of a proposed slurry handling system, and therefore has often made the selection of correct size slurry handling equipment difficult. Because of lack of knowledge about slurry flow a study of slurry flow theory has been made at the Portland Cement Association&apos;s Research and Development Laboratory with the idea of developing a method whereby friction losses due to slurry flow may be predicted for any size pipeline. The flow equations developed have been checked by pilot plant size equipment. DERIVATION OF FLOW EQUATIONS It has been known for some time that limestone and clay slurries handled in cement plants do not flow in the same manner as a Newtonian fluid such as water. When a Newtonian fluid flows the shear stress at any flow velocity is proportional to the rate of shear. This phenomenon can be illustrated by a line (Figure 1). The viscosity of the fluid is the slope of the curve. Thus, the flow properties of the material may be characterized by a single materials constant: viscosity. When a non-Newtonian fluid with the type of characteristics exhibited by limestone and clay slurr-ries flow, a similar curve can be constructed (Figure 2). This graph is a shear diagram of a Bingham plastic non-Newtonian fluid. It should be noted that with the Bingham(1) plastic type of flow viscosity, the slope of the curve, is still an important materials constant. In addition, however, there is another materials constant, namely the yield stress of the material. One way to visualize this constant is to consider it as the amount of energy that must be put into a Bingham plastic material to start it flowing.

Jan 1, 1961

By P. G. Hallof

Only recently has the term Induced Polarization found its way into geophysical literature. Schlumberger first mentioned the possible use of the induced polarization effect in one of his early papers. Later, induced polarization was the subject of several university theses, such as Seigel&apos;s at the University of Toronto and Bliel&apos;s at the Michigan School of Technology. In addition, a group at the New Mexico School of Mining and Technobgy has done work on induced polarization. There is very little to be found in print on the subject of induced polarization. Several papers have been presented at meetings, the 1958 AIME and SEG* conventions, for instance, on laboratory measurements of the effect and theoretical considerations useful in the interpretation of field results. This paper is the first attempt to present actual field results which show the usefulness of induced polarization as a prospecting technique. There are several phenomena that can cause polarization when electrical current is passed through the ground. In a paper presented at the 1958 SEG* meetings Professor T. R. Madden of M. I. T. demonstrated that only two of these gave rise to appreciable effects. The first is a result of the membrane and diffusion effects in a sandstone that contains appre- ciable amounts of clay minerals. The unbonded charges associated with the clay mineral forma material that passes positive and negative ions with different mobilities. When current is passed through such a system for some period of time, polarization results. The second phenomenon, which gives rise to very much larger polarization effects, is the one used in the new prospecting technique. These effects are a result of the blocking action or polarization of metallic or electronic conductors in a medium of ionic solution conduction. This electrochemical polarization, called "the over-voltage effect" by electro-chemists, occurs whenever electrical current is passed through a volume of rock which contains metallic minerals such as base metal sulphides. This polarization at metallic interfaces in ionic solutions depends upon the chemical energies necessary to allow the ions to continue the flow of current by giving up or receiving an electron from the metallic surfaces. The energy stored in this reaction isanalogous to that stored when a condenser is charged. If a d. c. current flowing through such a system is interrupted, the polarization can be detected as a small, decaying current that flows after the applied current is discontinued. The decaying potential measured is a result of the current flow caused by charges returning to their equilibrium positions from the positions they assumed under the applied potential field. Because of the polarization, there is an excess of change at each metallic interface. There is an alternate method of measurement of the induced polarization effect. The electrical

Jan 1, 1961

By W. A. Selvig

BY plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Com-mittee on Coal Classification. This scheme was sponsored by Sub-committee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic.. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as follows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group, 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. , The lignitic class of coal was divided into two groups both below 8,000.B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By V. F. Swanson

At the AIME meeting in Tampa in Oct. 1966, an empirically developed equation was presented which allowed the calculation of free settling velocity for any sized particle: 1 [ ] This equation requires the use of two parameters a and p which are coefficients derived from boundary layer theory.2 It was possible to develop values of a and p for several minerals by back calculation of published data. The original equation had one major flaw. When the fluid density exceeds the density of the solids, the solution to the equation becomes imaginary. A flaw was indicated also by the fact that galena and sylvite both having cubic cleavage, did not have similar values for a and b. Galena gave calculated values of a = 1.082 and g = 3.11, while sylvite gave values of a = 1.870 and p = 2.56. These flaws prompted further study of the equation, resulting in the following empirical modification: [ ] It is obvious a real solution of the equation is possible for all values of ps and p. When PL > PS, V is negative, indicating that the particles will rise against the attraction of gravity. The validity of the modification is borne out by the fact that when values of a and p were back calculated for galena and sylvite using the modified equation, both minerals gave values of a = 1.038 and p = 3.01. With the modification shown in Eq. 2, Newton&apos;s friction factor becomes [ ]

Jan 1, 1976

By Bruno Nordberg

THE high cost of coal in Butte and the development of large amounts of cheap electric power from the Missouri river caused the Anaconda Copper Mining Co. in 1908 to make an investigation as to the possibility of adapting this cheap electric power for the operation of their many large hoisting plants. At this time electric power had already been adopted for practically all other power purposes around the mines, such as pumping, compressing air, etc. The map (Fig. 1) shows the location of the mines of the Butte mining district. These mines are located within a circle of approximately a 1-mile

Jan 9, 1913

By E. F. Adkins, R. W. Douglas

The variation of the spectral emissivity of osmium and ruthenium with temperature can be expressed by the following relations: DURING a study of the sintering characteristics of osmium and ruthenium, discrepancies in the previously accepted melting points of the metals were noted. The melting temperatures had not been measured at the time of the work, but were estimated in the literature as 2700°C for osmium and 2450°C for ruthenium.&apos; A recent investigation by Baird2 has shown the melting temperatures of osmium and ruthenium are 3000" and 2250° C, respectively. In the present work, osmium bars sintered at temperatures as high as 2900° C showed no evidence of melting, whereas ruthenium showed definite evidence of melting at temperatures as low as 2250°C. In view of the apparent discrepancies, the melting temperatures of both metals were determined. The spectral emissivities of both metals were determined as an aid to studies of the sintering characteristics of these metals. MATERIALS AND PROCEDURES The materials used in these studies were metal powders supplied by Englehard Industries, Inc., through the courtesy of The International Nickel Co. Analytical data from three laboratories, although not in complete agreement as to the purity of the material or the major impurity elements, indicated that the maximum impurity levels were 0.5 and 1.0 wt pct in osmium and ruthenium, respectively. The metal powders were pressed to 1/4 by 1/4 by 6-in. bars at 20Tsi using carbon tetrachloride as a lubricant. The pressed bars were presintered 1 hr at 1200°C after heating 1 hr at 400°C. The presintered densities of the several bars of the metals ranged from 65 to 80 pct of ideal density. Specimens were self-resistance heated in a vacuum sintering bell. Temperatures were measured with an L&N, disappearing filament optical pyrometer. True temperatures were read at the base of an 0.30-in.-diam, 0.150-in. deep hole drilled into the center of a presintered bar. Apparent temperatures were read from the surface of the bar adjacent to the hole. MELTING POINT DETERMINATION The melting temperature of the metals was determined as the temperature at which a slight additional increase in current through the specimen resulted in a reduced temperature at the base of the hole. The apparent reduction in temperature is a result of the liquid metal filling the hole, thus altering the black-body conditions. The melting points of osmium and ruthenium, based on three deter-

Jan 1, 1962

By F. W. Lake, H. A. Brett

With each year bringing the exploration of deeper and deeper producing horizons in the effort to maintain production, the problem of lifting the oil to the surface is continually becoming more difficult. Flowing and gas-lift wells eventually decline to such a point that pumping is necessary. The increasing loads on sucker rods resulting from deeper pumping operations are approaching the ultimate strength of the rods with consequent reduction in the factor of safety. With this diminishing factor of safety, the vibratory stresses causing fatigue, crystallization, and ultimate fracture become more important. These vibratory stresses are the result of varied pumping conditions which, if properly understood and investigated, may be eliminated to a great extent. To accomplish this purpose, a recording dynameter has been developed which gives an indicator card showing the actual load on the polished rod at each point of the pumping cycle. Recording Dynamometer The instrument consists of a dynamometer head of the piston and cylinder type filled with castor oil, and a recording device, the movable card holder being connected with the dynamometer through a system of levers and the hollow spring gage connected with the fluid chamber of the dynamometer by a high-pressure flexible tube. The dynamometer head is hung from the beam with an ordinary hanger and lugs on the cylinder, while the piston is attached to the polished rod. The movable card holder actuated through levers moves in a vertical direction pro-portionate to the movement of the polished rod. The recording arm of the hollow spring gage inscribes on the card the pressure at all times. Thus by proper scales, the indicator card gives the load on the polished rod at all points in the pumping cycle. Fig. 1 shows the hookup of the recording dynamometer at a pumping well.

Jan 1, 1928

[Chairman ZAY JEFFRIES, Vice-chairman S. SKOWRONSKI, Chairman WILLIAM M, CORSE, Secretary Executive Committee J. R. FREEMAN, JR., Local Section G. E. JOHNSON R. S. ARCHER, Non-ferrous Data Sheets P. D. MERICA EDGAR C. BAIN, Journal Committee L. W. SPRING SAM TOUR, Papers Committee F. L. WOLF H. C. JENNISON, Membership Committee Local Section Committee J. R. FREEMAN, JR., Chairman R. J. ANDERSON, Cincinnati R L. DOWDELL, Minneapolis R. S. WILLIAMS, Boston G. H. CLAMER, Philadelphia W. A. SCHEUCH, Chicago R. F, Woon, New York Papers Committee S. SKOWRONSKI, Chairman F. H. DIx, JR.-Aluminum E. R. DARBY-Bronze C. S. WITH ERELL-Copper H. A. BEDWORTH-Brass W. K. FRANK-BRONZE F. W. HARRIS-Copper R. L. SUHL-Nickel H. M. ST. JOHN--Foundry Metallurgy R. S. DEAN-Theoretical Metallurgy]

Jan 1, 1928