Search Documents

By A. F. Bridge

IN order to show the need for gas reserves, their control, and conservation, in California, it is necessary to describe briefly the local conditions under which gas is produced and marketed, to point out the lack of coordination between supply and demand, and to relate the history of efforts to prevent wastage. There are now 24 fields in California producing a surplus of gas over field fuel requirements. They are usually grouped geographically into three divisions, as follows: (I) Los Angeles Basin (Los Angeles and 0 r a n g e Counties), thirteen fields, all casing-head gas. Total daily gas available for sale 125,000, 000 ?cu.ft. (2) Coastal (Ventura and Santa Barbara Counties). Seven casine-head and one dry gas field. total-avail- able daily, 165,000,000 cu.ft. (3) San Joaquin Valley (Kern, Kings, Fresno, and San Joaquin Counties). Four casing-head fields, five dry gas fields, and two producing casing- head and dry gas from different zones. Total available daily pro- ducticon, 475,000,000 cu.ft. Total all fields, 765,000,000 cu.ft. daily.

Jan 1, 1936

By G. R. Hodgson, M. P. Lebourg

The introduction in the field of a new type well completion called for the setting of tubing open-ended in the well before perforating the casing. This paper describes a new perforating tool of the shaped charge expendable type, small enough to pass through tubing and powerful enough to perforate the casing. The perforations are produced at an angle and are large enough for optimum production. Performance of this tool in targets and under various well conditions is described. Very often no lifting equipment will be available at the well. In some cases, pressure will exist in the well at the time of the perforating operation (workover wells or multiple trip perforation) ; therefore, new equipment and new technique for the perforating operation were devised. This paper describes this equipment and technique, particularly casing collar recording, sheave support, and cable pull-down device. this last item being necessary for wells under pressure. Results obtained with this tool in the field are given. INTRODUCTION One of the key requirements for the introduction in the field of a new method of permanent well completion was the development of a new perforating method involving the use of a perforating gun small enough to go through tubing and with enough penetrating power to perforate the casing satisfactorily. The equipment described in this paper was basically designed to go through open-ended two-in. tubing and to perforate 5 1/2 in. casing. The equipment is illustrated in accompanying figures. NEW COMPLETION METHOD With the new permanent type well completion, the production string of casing is run and cemented through the potential producing zone. Open-ended tubing is -then run into the well and used to replace the drilling fluid with oil or water. The amount of the oil or water "cushion" can be varied according to the expected bottom hole pressure. Thus, if desired, the hydrostatic head can be greater, equal to, or less than the expected pressure within the zone to be perforated. Mud having been displaced, the tubing is -then positioned so that the end is above the zone to be perforated. The Christmas tree and flow lines are installed and tested. The drilling rig can now be removed from the well since it is not necessary for the perforating operation, thus resulting in a saving in rig tme. The perforating equipment is then moved to the well and the gun lowered through the tubing. After the gun passes out of the open end of the tubing, the depth measurements are correlated with casing collars and the gun placed opposite the zone to be perforated. Upon firing, the gun body is shattered and falls to the bottom of the well. Since the lubricator has been closed before firing, it is possible to withdraw the casing collar locator and head and then open the well immediately to the tanks. DESCRIPTION OF GUN An investigation of two basic types of Perforators, namely a bullet perforator and a shaped charge gun, was undertaken towards the development of a gun to meet the aforementioned requirements. Preliminary tests on various bullet perforator designs within the diameter limitations did not give results encouraging enough to warrant further study. Somewhat better results were obtained by using conventional shaped charges; but, as in the case of the bullet types, the necessarily small overall diameter proved to be a severe limitation and resulted in insufficient penetration. A shaped charge employing a new design was developed which gave excellent penetration. These shaped charges were designed to produce a large hole directed upward at a 45" angle. In order to obtain the maximum space possible for these charges, it was decided to use an expendable carrier made of drillable material, usually aluminum, which would shatter at the time of firing, leaving only harmless fragments at the bottom of the hole. The fixed spacing is five shots per ft. wit11

Jan 1, 1952

By H. L. Shergold, O. Mellgren

Concentration of fine quartz particles at the iso-octane/water interface has been investigated under different conditions of pH and dodecylamine concentration. The results obtained from the related studies on the effect of amine concentration and pH on the interfacial tension, adsorption density, electrokinetic potential, contact angle, and concentration of the various amine species in the system are presented. A good correlation was obtained between these different variables. It is well-known that very fine mineral particles are difficult to float in conventional flotation machines. Flotation rate studies have revealed that the rate of flotation of fine mineral particles is much smaller than that of coarser size fractions. The theories accounting for this behavior have been discussed by Arbiter and Harris1 and also Meloy.2 Theoretically, a hydrophobic fine particle might never make contact with a bubble because of the presence of an energy barrier in the vicinity of the air/water interface.' This energy barrier will have electrostatic, hydrodynamic, and Van der Waals force components. It was thought that by using an oil phase instead of air the energy barrier would be decreased so that fine particles could be concentrated at the oil/water interface more readily than at the air/water interface. The technique used involves dispersing the fine particles in water, containing the appropriate chemical reagents, and injecting a fine dispersion of iso-octane oil droplets into the pulp. After vigorous conditioning, the pulp is passed into a separating column where the oil droplets coated with a layer of mineral particles rise to the surface to form a separate layer. Air is introduced into the base of the separating column to ensure that heavy agglomerates of oil and particles report with the organic layer. This technique has been described previously4 and adopted by Lai and Fuerstenau5 who studied the alumina-dodecyl sulfonate system. The interfacial phenomena in the system composed of hematite, water, and iso-octane in the presence of sodium dodecyl sulfate have been studied and the results reported" earlier. This paper describes the results obtained from investigations into the interfacial phenomena in the quartz/water/iso-octane system in the presence of dodecylamine. The technique used in measuring the interfacial tension, electrokinetic potential, contact angle, and adsorption density were similar to those described previously? Materials Selected pieces of a high purity natural quartz, from the Isle of Man, were crushed in a laboratory jaw crusher and pulverizer. The — 52+72 mesh size fraction was retained and leached with successive washes of hot concentrated hydrochloric acid to remove iron impurities. When no iron was detected in the solution by ammonium thiocyanate, the quartz was washed thoroughly with distilled water until the conductivity of the wash water assumed that of the distilled water. Samples of 25 g of the —52+72 mesh quartz were ground for 5.25 min in an agate vibratory mill. The ground product was 100% —44 m and 57% —10 am, as determined by the Andreasen pipette. The specific surface area of the sample used for the adsorption and flotation tests was 0.94 sq m g-l. This corresponds to a mean particle diameter of 2.4 am. The —44 am quartz sample was stored under vacuum in the presence of silica gel crystals. For the contact angle determination between the three phases, quartz, iso-octane, and water, a piece of the natural quartz was ground into a block about 15 mm long, 15 mm wide, and 5 mm thick. One surface of the block was then polished by successively finer grades of silicon carbide "paper." The final polishing was conducted with alumina on a "hyprocel" paper. The polished quartz specimen was cleaned using nitric acid and ethyl alcohol followed by a wash with distilled water and then stored under distilled water. This pro-

Jan 1, 1971

By C. A. WARNER

AN OIL and gas mining lease contract, as entered A into by and between 'the lessor and the lessee, contains certain express covenants stipulating, in part at least, the exact performance thereof; it also contains certain implied covenants, among which may be included that of protection of the leased premises against drainage by the drilling of necessary offset wells. In the drilling for, and production of, oil and gas, however, it not infrequently happens that the lessee, acting in good faith, does not deem it prudent to, drill a test thereon even though the location for such test is offset by a producing well on an adjoining lease. Such conclusion, on the part of the lessee, is generally construed by the lessor as constituting a breach of the implied covenant mentioned above, and he may take proper action to secure satisfaction therefor. The action against the lessee is generally for cancellation or relinquishment of the lease, together with, or apart from, claims for damages allegedly sustained through failure to properly protect against drainage of the leased premises.

Jan 1, 1931

By Oscar A. Glaeser

MINE VENTILATION is an important factor in mine maintenance as well as having direct bearing on labor efficiency. Effective ventilation systems are costly, especially those for the deeper mines, but with intelligent direction the worth of a system is usually greater than its cost. In most mines using mechanical ventilation, and practically all deep mines, it has been found beneficial to equipment, timber, and the ground, to run the fan or fans continuously even though production has been curtailed or entirely suspended. Therefore, economies in ventilation may be overlooked when general cost reductions are necessary. The operating costs of a well-designed ventilation system should be capable of reduction during periods of curtailed or suspended operations. A mine that is ventilated by splits, or that can be sectionized, can reduce its fan-power costs considerably, and provisional divisions can sometimes be made in other mines, in which the air is ordinarily coursed through all the workings, without harmful effects.

Jan 1, 1932

By Donald L. Everhart

SOONER or later intelligent exploration for uranium leads to these questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? These matters, of course, make a big difference in how best to look for orebodies. Before these questions are discussed it might be well to point out other factors bearing on the subject. The whole business of uranium exploration is only a little over ten years old, participation by the public is only about six years old, and real interest and activity by more than a few large mining companies has arisen only in the past two or three years. Throughout this short period, uranium exploration has been affected by the unique influences of necessary security measures and by division of the over- all job into individual projects by a large number of specialists in diverse fields. This has meant that a normal interchange of information on the nature of uranium deposits has really only just begun. Com- pared to the vast amount of published studies on iron, copper, lead, zinc, and gold deposits over the past 50 to 75 years, current knowledge of uranium deposits is in its infancy and much of the pertinent information is still scattered about in a number of unpublished sources. The volume of reports on all phases of uranium exploration is now beginning to mount at a remarkable rate, and geologists with widely varying specialized backgrounds in uranium geology are engaging in spirited debates over the origin of uranium and the relative importance of geologic controls of various deposits.

Jan 9, 1954

By James E. Lawver, James L. Wright

This paper discusses the design and calibration of a Faraday pail for measuring electric charge. The paper also shows that at least for two minerals, quartz and calcite, the phenomenon that Johnson termed "reversibility" can be explained in terms of the contact electrification between the minerals and the metal rotor of an electrostatic machine. Each year the free world produces about 13 million tons of mineral concentrates by electrical separation. However, despite the rather general acceptance of electrical concentration as an industrial process, research in this area has lagged far behind the efforts devoted to competitive processes such as froth flotation. The purpose of this paper is to describe the design and calibration of a Faraday ice pail for measuring charge density on mineral grains and to show some of its applications in the area of electrostatic and electrodynamic research. THE DESIGN AND CALIBRATION OF FARADAY PAILS FOR ABSOLUTE CHARGE MEASUREMENT The electric charge on mineral grains at a given time during an electrical concentration process is de- pendent on many factors and cannot, in general, be accurately calculated a priori. It is thus important to devise a method of measuring absolute charge. One method of measuring electric charge is to note the potential rise of an electrometer when charged particles drop into a Faraday pail. Two types of Faraday pail have been constructed and calibrated. The first type, Faraday Pail I (Fig. 1), is a vertical pail originally designed to measure the charge due to contact electrification between mineral grains and a metal rotor or due to conductive induction when mineral grains are passed over a rotating cylinder in the presence of an electric field. The second type, labeled Faraday Pail II (Fig. 2), is a horizontal pail designed to determine the charge distribution of mineral grains after they pass through the separating zone of the electrical concentrator shown in Fig. 4. The main advantage of the horizontal pail is its low head-room requirement and the long opening which enables the experimenter to sample the entire width of the stream of minerals being separated. The Faraday pails were calibrated in the following manner: A calibration head was constructed in the form of a hollow brass sphere that could be held in an insulated metal cylinder by vacuum (Fig. 1). The capacitance of the sphere was calculated by measuring the capacitance of the sphere and cylinder combined and that of the cylinder alone and subtracting the latter measurement from the former. The sphere was then charged to a known potential (V) and allowed to drop into the Faraday pail which was attached to a Keithley Model 610A electrometer. This instrument has an accuracy of 2% full scale and has

Jan 1, 1969

By H. E. Strauss

The short-time tensile-strength test, while it has not attained the practical importance of the creep test at elevated temperatures, has the advantage of being rapid and is satisfactory for determining relatire strengths. For platinum and its alloys, which frequently are used at high temperatures under ill-defined conditions, the short-time test provides useful data that aid in the selection of the most promising alloy for each use. Measurements have been made upon 13 alloys, using wire 0.0031 in. in diameter, the choice of alloys and of wire size being determined by the requirements of a practical problem. Later the measurements were extended to higher temperatures by the use of heavier wire, 0.010 in. in diameter. Apparatus The use of fine wire made the necessary equipment very simple, since no effort was made to measure the elongation. A small platinum-wound horizontal furnace was used, 1/2 in. in internal diameter by 1 ft. long, with the wire threaded through it. The wire, clamped at one end while the other ran over a ball-bearing pulley, of a total length of 29 in., was loaded directly by running sea sand into an attached basket, making the rate of loading and not of elongation constant. The sand flowed from a funnel, under a head of 3 in., into the basket 3 in. below the orifice, at the rate of 170 grams per minute. Pulley friction and bending resistance of the wire as well as the force of impact of the sand could be neglected, being 3 grams and 0.5 grams, respectively. Furnace temperature was uniform within ±5° C. over a length of 3 in., although a drift with time occurred, the largest amount being 20" C. No provision was necessary for a controlled atmosphere. In making the measurements, the furnace was brought to equilibrium before being used, and the temperature was measured with a platinum platinum-10 per cent rhodium thermocouple and a high-resistance pyrometer before and after all the tests at one temperature. The wire sample, after being threaded through the furnace and attached to the

Jan 1, 1940

By H. E. Strauss

The short-time tensile-strength test, while it has not attained the practical importance of the creep test at elevated temperatures, has the advantage of being rapid and is satisfactory for determining relatire strengths. For platinum and its alloys, which frequently are used at high temperatures under ill-defined conditions, the short-time test provides useful data that aid in the selection of the most promising alloy for each use. Measurements have been made upon 13 alloys, using wire 0.0031 in. in diameter, the choice of alloys and of wire size being determined by the requirements of a practical problem. Later the measurements were extended to higher temperatures by the use of heavier wire, 0.010 in. in diameter. Apparatus The use of fine wire made the necessary equipment very simple, since no effort was made to measure the elongation. A small platinum-wound horizontal furnace was used, 1/2 in. in internal diameter by 1 ft. long, with the wire threaded through it. The wire, clamped at one end while the other ran over a ball-bearing pulley, of a total length of 29 in., was loaded directly by running sea sand into an attached basket, making the rate of loading and not of elongation constant. The sand flowed from a funnel, under a head of 3 in., into the basket 3 in. below the orifice, at the rate of 170 grams per minute. Pulley friction and bending resistance of the wire as well as the force of impact of the sand could be neglected, being 3 grams and 0.5 grams, respectively. Furnace temperature was uniform within ±5° C. over a length of 3 in., although a drift with time occurred, the largest amount being 20" C. No provision was necessary for a controlled atmosphere. In making the measurements, the furnace was brought to equilibrium before being used, and the temperature was measured with a platinum platinum-10 per cent rhodium thermocouple and a high-resistance pyrometer before and after all the tests at one temperature. The wire sample, after being threaded through the furnace and attached to the

Jan 1, 1940

By A. J. Teplitz, J. K. Rodgers, E. M. Pohoriles

This note is presented in order to call attention to a newly developed laboratory apparatus that appears to have interesting possibilities for the study of lost circulation of the pressure-parting type, for a more realistic evaluation of sealing materials for this type of loss, and for investigation of other aspects of hydraulic fracturing. A study of lost circulation, conducted jointly by operating divisions of the Gulf Oil Corp. and the Gulf Research & Development Co., has been in progress for the past few years. Earlier phases of the study dealt with mechanical factors contributing to loss of returns in laminar type sediments.' One aspect of this type of loss which has been widely discussed in the literature and elsewhere concerns the geometry of the fractures into which such losses occur. This subject is not merely a philosophical one, but has an important bearing on procedures for combating lost circulation difficulties and on other well operations. The further course of the collaborative studies previously mentioned has produced some information on this subject which, though limited in amount, is believed to be significant. In several typical cases of lost circulation in laminated shale and sand formations, the wells have been surveyed with instruments2,3 capable of detecting the points of loss with considerable accuracy. These wells were located in the Gulf Coast of Texas and Louisiana, in the Texas Panhandle, and in the Rocky Mountain area. In each of these instances the loss was shown to be occurring at some distance removed from the bottom of the hole and sharply confined to a very narrow interval, less than 1 ft in thickness. It is rather difficult to imagine that fractures of a vertical nature' would be of the limited extent indicated by the surveys in these wells. Furthermore, the high rates of loss at relatively low pressure differentials observed in some of these instances together with the narrow intervals involved would appear to require the radial flow pattern which would be associated with a more or less horizontal fracture plane. In view of the foregoing observations and records of successful squeeze cementing operations, in attempting to construct a laboratory apparatus For simulating pressure induced lost circulation, it was decided that the design should be based on a horizontal type of fracture. It was realized that5,6 Vhe production of horizontal fractures in a formation with non-penetrating fluid requires some mechanism for transmitting vertical components of the hydraulic forces to the plane of parting. This was accomplished, as will be evident in the description of the apparatus that follows, by providing recesses in the wall of the borehole which are believed to be representative of wellbore configuration found in Gulf Coast wells. The possible influence of such borehole irregularities on both pressure fracturing and the treatment of lost circulation appears to have been neglected in many studies of these subjects. It is believed that the present apparatus, incorporating features that take into account some of the factors mentioned, will provide means of gaining a further understanding of pressure induced fracturing and possibly for more realistically evaluating the numerous sealing agents, particularly the non-time-setting materials employed in treating the pressure-parting type of loss. DESCRIPTION OF APPARATUS The test cell used in the laboratory investigations is shown in Fig. 1. A schematic diagram of the entire system is shown in Fig. 2.

Jan 1, 1956

By H. L. Marcus, C. D. Turk

Titanium was physically vapor-deposited by electron beam high rate evaporation. Rates of 50,000 and 85,000Å per min at deposition temperatures of 480°, 535°, and 595°C were used. Deposited thickness ranged front 0.004 to 0.010 in. The evaporated titanium had a high degree of basal Plane texture. The specimens were tested in tension at temperatures ranging from 78° to 520°K. From the data, the yield stress, thermal component of the yield stress, and work hardening characteristics were found as a function of temperature, deposition rate, and deposition temperature. It was found that Taylor's equation, best fit the work hardening data with m = 1/2. MANY investigations have been made on the tensile deformation characteristics of commercial- and high-purity titanium.1"7 The data obtained from these experiments emphasize the fact that the mechanical properties are generally related to the method of production. The correlation of mechanical properties to production history arises from the dependence of impurity concentration on the extraction and melting technique used. Additional effects are derived from crystallographic texturing which can result from fabrication history. Lee and Backofen8 and other investigators9 have shown that crystallographic texturing in titanium sheet has a significant effect on the deformation characteristics. Bunshah and Juntz10 prepared high-purity titanium by high rate physical evaporation techniques. These authors found the deposited material to have a columnar structure with grain sizes ranging from 12 to 104 µ, depending upon the substrate temperature. The room-temperature strengths of the coarse-grained distillate were similar to arc-melted, rolled. and annealed crystal bar titanium. Commercial-purity titanium was also produced experimentally in our laboratory using high rate physical vapor deposition techniques. The commercially pure material has a finer structure than the high-purity distillate,10 and is highly textured. Since the method of preparation and degree of texturing affect the mechanical properties, a research program was initiated to determine the temperature dependence of the yield stress and work hardening characteristics as a function of high rate deposition parameters. This paper relates the results of the investigation. EXPERIMENTAL A) Material Preparation. The titanium was received in the form of commercial-grade 0.096-in.-diam wire which has a composition of 0.016 pct C, 0.0037 pct N, 0.110 pct 0, 0.011 pct H, 0.05 pct Mn, 0.051 pct Fe. balance Ti. The wire was continuously fed into a vacuum evaporation unit as shown schematically in Fig. 1. The deposition chamber was evacuated, purged with argon, and reevacuated to a pressure of 10-5 Torr which was maintained during deposition. A focused electron beam was used to evaporate the titanium from a water-cooled copper crucible. The titanium vapor was condensed onto a preheated titanium substrate. The temperature of the substrate was controlled within ±5°C for the deposition temperatures of 480°, 535°, and 595°C. Control of the input power enabled the use of two deposition rates. 50,000 and 85,000Å per min. The evaporated titanium had a final analysis similar to that of the input titanium, within experimental limits. B) Testing. The evaporated titanium was physically stripped from the titanium substrate and machined into tensile specimens with 1-in. gage lengths. In addition, tensile specimens of as received annealed 35-A titanium sheet with a 20 µ grain size and 45 pct cold-rolled 35-A were also prepared. All specimens were tested in tension in an Instron at a strain rate of 3.3 x 10"4 in. per in. per sec. Proportional limit has been used as a measure of yield strength. Tests were conducted at 78°, 220°, 300°, and 520°K. Metallography, X-ray diffraction, and electron microscopy were used to correlate structure with the deposition parameters and mechanical properties. Room-temperature X-ray measurements were made to determine the phases present. Pole figures and a scans were made to determine deposition texture. Because the vapor deposition was symmetrical about the normal to the substrate, there was no preferred di-

Jan 1, 1969

By J. L. Taylor, Pol Duwez

THE present knowledge of the Ti-Al system is limited to the portion of the diagram extending from pure aluminum to the intermetallic compound TiAl3' A preliminary investigation of the titanium-rich Ti-A1 alloys revealed that the solubility of aluminum in titanium is quite extensive and that the transformation temperature of titanium is raised by alloying with aluminum. From an X-ray diffraction study of alloys containing up to 75 atomic pct Al (TiAl3), the phase boundaries at 750°C were located as follows: the a titanium solid solution extends from 0 to about 36 atomic pct Al, a two-phase region exists from 36 to 46 atomic pct Al, and an intermediate phase of varying concentration extends from 46 to 62 atomic pct Al. The purpose of the present paper is to describe the crystal structure of this new phase. The alloys were prepared by melting in a helium arc furnace on a water-cooled copper plate, using a furnace essentially the same as that described in ref. 2. The titanium metal was of the iodide type furnished by the New Jersey Zinc Co., and a piece of pure aluminum (99.99 pct) was obtained through the courtesy of the Aluminum Co. of America. After melting, the samples, weighing approximately 5 g, were sealed in evacuated fused silica tubes and homogenized for 4 hr at 1000°C. The specimens were then held for 10 days at 750°C and rapidly cooled to room temperature. Filings were then taken from each sample, sealed in evacuated vials, annealed at 750°C for 4 hr, and rapidly cooled to room temperature by quenching the vials in water. Powder diffraction patterns were obtained with a 14.32 cm diam camera, using K copper radiation filtered through a nickel foil. Structure Determination The X-ray diffraction patterns of the alloys containing 46, 50, 55. 60, and 62 atomic pct Al were identical, except for a slight shift in the positions of the reflections. The alloy containing 55 atomic pct Al was chosen far structure determination. The powder pattern contained 37 reflections and the a, doublets were well resolved in the back-reflection range. The relatively small number of reflections and the sharpness of the pattern were considered as an indication of a simple atomic arrangement in a relatively small unit cell of high symmetry, and an attempt was therefore made to solve the structure without single crystal work. A satisfactory fit was found on a large scale Hull-Davey tetragonal chart for an axial ratio of approximately 1.45. All the reflections were readily indexed and the tentative unit cell dimensions were computed to be a - 2.81 kX, c - 4.07 kX, and c/a = 1.448. The indices (hkl) and the values of d and sin2 A are given in Table I. The agreement between observed and computed sin2 is quite satisfactory. Once the unit cell was known, the details of the structure were readily found. First, it is obvious that the number of atoms per unit cell cannot exceed two, since more than two atoms would lead to a density greater than that of pure titanium. The next logical step is to assume that the two atoms occupy the corner and center of the cell. If this assumption is correct, the structure may be described as follows: space group D1, - P 4/mmm; one titanium atom in a: 000; one aluminum atom in d: 1/2 1/2 1/2: and no extinctions. Assuming this structure to be the correct one. intensities were computed by means of the usual equation: sin2 0 cos 0 where F is the structure factor; 8, the Bragg angle. and p, the multiplicity factor. The calculated values of intensities are compared in Table I with the visually estimated intensities. The agreement is quite satisfactory and the structure is therefore confirmed. The crystal structure of TiAl just described is the same as that of AuCu ordered. The AuCu ordered

Jan 1, 1953

By William R. Chedsey

ALTHOUGH few changes can be reported in educational methods at the mineral technology schools during 1940, other events have taken place of direct interest to, and that will have a profound effect upon, mineral industry education on the United States. In the erection of new buildings, some notable changes have been made on the campus, The U.S. Bureau of Mines Experiment Station at the University of Utah, Salt Lake City, was dedicated on May 20. The construction and equipment of this building cost between $300,000 and $400,000. It will be the general headquarters for the metallurgical division of the Bureau and will have a pronounced effect upon the mineral industries research program at the University.

Jan 1, 1941

By Howard A. Meyerhoff

Nonmetallic rock and mineral products are so diversified that any generalizations regarding the industries based upon them are of doubtful value and can be misleading. They are geared to every phase of the national economy and respond sensitively and immediately to any economic change, but the responses vary with the individual products. They are also affected by political and competitive factors to a degree that is disconcerting and, at times, ruinous to operators, owners, and stockholders of mineral properties. It is not unusual to find these special factors functioning in reverse of general trends insofar as individual products are concerned. As this summary is being written in the final weeks of 1949 production statistics for the year are not complete, but it is obvious that few, if any, new production records will be set, and that 1949 level, will, in general, be lower than those of 1948. The decline in output is not alarming and reflects in large part the tendency of users, who have been finding sources of supply more dependable to rely on prompt deliveries rather than on inventories to meet immediate needs. Except for the government's program of stock piling which, insofar as it has worked at all, is of more direct interest and benefit to foreign than to domestic producers, industrial inventories have been further reduced, and the neater balance between production and consumption has freed capital for the manufacturer and has cut down the serious hazard of substantial inventory losses. There are no quantity products and only a few special products that cannot be supplied in quick response to current demands. Normal development of a few nonmetallic industries has been retarded by the government's unpredictable application and irrational interpretation of antitrust laws, and by extension of preferential tariffs to new countries and new products. Synthesis is likewise a potent threat. in certain fields, but otherwise it is difficult to make a review of 1949 read much differently from a review of 1948. Changes have been qualitative rather than quantitative, except for a few operations that have been pinched out by the relentless competition that characterizes many of the industrial mineral industries.

Jan 1, 1950

J. C. WRIGHT.-The problem of organizing and maintaining a vocational class for those employees who are engaged in the mining industry depends on several most important factors. The first is the sympathetic cooperation of employer and employee; the second is to find the subject matter that must be presented to these men; and the third is to find the instructor who can present that subject matter. This is perhaps the most difficult, for we usually find a man who knows the material that is to be presented but is not a teacher or does not know how to organize his material. The man must know the subject matter from the standpoint of absolute contact with industry in order to be a successful teacher. I have come into contact with two kinds of schools organized in connection with mining occupations. In one type the instruction leans very largely toward elementary subjects, arithmetic, reading and writing and spelling; it is not of such a character as to help or improve the working man in his occupation in the sense that we are attempting when we speak of vocational education. In the other type of school, an engineer is usually employed as a teacher. He immediately begins to give the things with which he is most familiar and the instruction becomes such as only those who possess a high-school or college education, perhaps, are able to receive. In between these two schools is the school we are trying to, promote, a school that will meet the needs of those employed. MARGUERITE W. JORDAN,* Altoona, Pa. -Vocational education has become the business man's problem; for he is the keeper of that white elephant, labor turnover, and anything that will decrease the size of the monster is worthy of serious consideration. This vocational education can do; for it can supply many of those deficiencies in upbringing and. environment that make for the discontent and restlessness of our varied classes of unskilled labor: the Anglo-Saxon mountaineer; the Southern negroes who have crossed Mason & Dixon's line by the thousands, "searching satisfaction for our minds;" and the still greater number who have sought across the sea America, "the promised land.

Jan 4, 1919

By John J. Porter

Unusual problems have arisen at certain iron blast-furnaces in Virginia through the fact that the ore-supplies, derived from the Oriskany formation, contain from a trace up to 1 per cent, of zinc oxide. Since the technical literature bearing on this subject is very scant, the following notes, based on personal experience, will probably be of value to those of our members who are interested in iron blast-furnace practice. The course of zinc through the blast-furnace is readily traced. Entering the throat as zinc oxide, finely dissemiuated through the ore, it descends unchanged to the fusion-zone, since a temperature of 1,000" C. or more is required for its reduction. At the fusion-zone, the zinc oxide is reduced by solid carbon to metallic zinc, which is set free as vapor and rises with the ascending gases to the cooler zones of the furnace. In cooling through the range of temperature from 1,000" to 500° C. the zinc is re-oxidized according to the reaction Zn + CO2 = ZnO + CO, and the resulting zinc oxide, being in a very fine state of division, is readily carried along by the ascending gases. Portions, however, deposit on the descending stock and are carried down, again to pass through the same cycle of changes. Still other portions deposit on the lining of the stack, and gradually form hard masses of "cadmia." Of the remainder of the zinc oxide, the greater part passes out of the furnace, and is either deposited in the down-comer, dust-trap, stoves, boilers and flues, or passes through the chimney into the atmosphere. A small portion escapes reduction and enters the slag as zinc oxide, while still another portion is absorbed into the lining of the furnace.

Jan 1, 1908

OIL FLOTATION DISCUSSED BY SOUTHERN CALIFORNIA SECTION . A meeting of the Section was held in the home of R. H. Norton, 335 W. 27th Street, on Mar. 10, thirty-two members and five guests being present. Vice-chairman Staunton opened the meeting with a description of an experiment he made with oil flotation, and then introduced the guest and speaker of the evening, L. C. Penhoel, of the South-western Engineering Co., who gave a very interesting and informal talk on the subject of Flotation. During the talk, as points were raised, there was a general discussion, in which valuable information was brought out. A number of examples of successful competitive, results by cyanidation and flotation in large milling plants in this country and Mexico were cited and discussed. The latter part of the meeting was devoted to a discussion of the bill introduced in the California State Senate, to license and register engineers. Mr. Ernest Strout gave a most favorable opinion of the principal of licensing mining engineers from his extensive experience in the working out of such a law on the Rand. All members who spoke were opposed to this bill as drafted but felt that the subject was of too great importance to the profession to attempt to amend the present bill in the week or two that remains, and that the passage of a bill that was so crude and inefficient for the achievement of the results desired, would harm the engineering profession. After the meeting adjourned a short time was spent in social intercourse, during which light refreshments were served. The appreciation and thanks of the Section is extended to Mr. and Mrs. R. H. Norton for their hospitality. ALVIN B. CARPENTER, Secretary-Treasurer.

Jan 5, 1919

I;. D. Godshall, Everett, Wash. (communication to the Secretary) : In Mr. Morse's interesting paper several statements occur which seem to require correction and comment. This is the more appropriate, since Mr. Morse has mentioned me by name, and has cited my "Review of the Russell Process,"* so that silence on my part might be taken as indicating an assent which I cannot give. On the first page of his paper Mr. Morse says that the " goingback " of chlorination was " the only difficulty encountered at Aspen," and adds that he has " never seen any explanation " of the cause. The plain inference is that he now fills this complete

Jan 1, 1896

By Francis Foley

IN examining steel under the microscope, one is constantly confronted with structures that are difficult to interpret. Recently, in a collection of samples for exhibition purposes, the writer found apiece of open-hearth runner metal, 2 in. (50 mm.) in diameter, that had been fractured for use as a sample of cast-steel structure. On polishing and etching a section for the purpose of photographing a field to typify the microstructure of steel in the "as cast" condition, a variety of structures was found (Fig. 1) so arranged as to arouse interest at once. For a distance of about 0.065 in. (1.6 mm.) from the skin of the runner, normal ingot structure was found (Fig. 2); this was followed by a zone, about 0.215 in. (5.5 mm.) wide, of considerably lower carbon content in which occurred a most pronounced Widmannstättian structure (Fig. 3); from this point on to the center of the runner, the metal was again of normal ingot structure (Fig. 4). Representative samples taken from the metal in the three zones showed the following analysis: C Ni Cr Metal from skin 0.34 1.26 0.63 Widmannstättian zone 0.21 1.18 0.63 Metal from center 0.34 1.32 0.67

Jan 7, 1919

By Sam F. Harrison

Most hydraulic system malfunctions make their presence known by sending out warnings that are loud and clear to the initiated mechanic, according to Aeroquip Corp. service engineers. To detect problems in many systems, they suggest that the use of four senses-sight, smell, hearing and touch-and a knowledge of how to interpret the information gathered are all that's needed to identify hydraulic malfunctions.

Jan 3, 1978