Search Documents

By Louis A. Panek

The purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fen tress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal held exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The miaximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repiesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: Safe R =(1/4)4p2n2r/g=p2n2r/g [I] in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sec2.

Jan 1, 1949

By H. Evans, L. A. Hunt

In the pellet-producing industry it is sometimes claimed that "The pellets are made in the concentrator," or that "The key to good pellets is in the balling operation." However, one claim is generally agreed on: If you can put in, on, and through the indurating furnace a good green ball of Proper size and adequate strength to withstand the handling, load, dehydration, and thermal shock until it is properly heat-hardened, you will have the pellet product you desire-that is, a "competent" green ball. The strength requirements that enable a competent green ball to withstand the environment of the indurating furnace are usually less restrictive than those for transporting the green ball from its source of production to the furnace. Experience has shown that different types of material may have different balling characteristics which may impose limitations on the quality of the green ball that can easily be produced under normal conditions. Therefore, if a specific material will produce a green ball that meets the physical requirements for competency in the furnace, but not for handling or transportation, various practices must be instituted to overcome this deficiency. In other words, if a normal handling system is too rigorous for the green balls that can be produced under standard conditions, then "handling with care" should be tried.

Jan 5, 1967

By John D. Siddle

Efficient energy utilization in the electrolytic zinc process, relative to other zinc processes, is one of the reasons for its wide adoption in recent years. Designers and operators of electrolytic zinc plants have pioneered process improvements, new equipment, and operating techniques to conserve energy. As energy costs advance still higher in the future, and competitive pressure against the less efficient producers increases, these or alternative energy-saving methods will be looked upon as a necessity for economic survival. Estimated energy savings which may be achieved by various equipment and techniques are included.

Jan 1, 1977

By Harold B. Fell

MANY oil producers are in disagreement with the idea held by some that an increase in the price of crude oil would be unlikely to stimulate much production and that we will be obliged to draw upon foreign sources of petroleum to supplement our domestic production as the years go by. Supporting our con trary opinion are numerous facts and figures. The most recent official estimate of the maximum efficient rate of production from the oil wells of the United States is 5,271,000 bbl per day. The Economics Advisory Committee of the Interstate Oil Compact Commission estimates, assuming certain supplies from imports and from natural gasoline and benzol, that crude oil require-

Jan 1, 1947

WHEN Magma Copper Company in 1952 set about finding $100,000,000 to finance the project of developing and equipping the property of its lusty progeny, the San Manuel Copper Corporation, A. J. McNab, president and guiding genius for both companies (and incidentally a mining engineer by profession), determined that he would avoid the mistake frequently made in such circumstances, of underestimating the cost, and thereby running short of funds before the job was completed. The fear that this might happen was one of the reasons why insurance companies, one potent source of "big" money, were reluctant to finance the enterprise. How, they asked themselves, would Magma, a relatively small company, get additional money in such a contingency? Insurance officials' thumbs were turned down. Conditions Imposed by R.F.C. The upshot was the negotiation by Mr. McNab for San Manuel of a contract with the Reconstruction Finance Corporation, dated July 10, 1952, whereby needed monies in amount up to $94,000,000 would be advanced as a loan, bearing 5 per cent interest. Arrangements were made for the separate financing of the new $10,000,000 town, needed for the project, through the Del E. Webb Construction Company of Phoenix, Arizona, and M.O.W. Homes, Incorporated, of Los Angeles. Thus the $94,000,000 drawing account was believed ample to provide for building the railroad, the mine plant, the concentrator, and the smelter, as well as for the underground development of the mine needed to start production. As a matter of fact, only

Jan 1, 1957

By D. S. Flett, D. W. West

The solvent extraction of chromium 111 has been studied for the system Cr 111, H,SO., H,O/RNH/RNH., xylene, where the primary amine used was Primene JMT. Rate studies have shown that extremely long equilibrium times are required, ranging from 1 hr at 80°C to 20 days at room temperature. Heating the solution prior to extraction increases the rate of extraction. The variation in the amount of Cr 111 extracted is an inverse function of the acidity of the aqueous phase. Thus, the slow rates of extraction appear to be connected with the hydrolysis of the Cr I11 species. Extraction isotherms for the extraction of Cr 111 have been obtained for two sets of experimental conditions, namely at 60°C and for a heat-treated solution cooled to room temperature. The separation of Fe 111 from Cr 111 and Cr 111 from Cu 11 in sulfate solution by extraction with Primene JMT has been studied and shown to be feasible. A survey of the literature relating to the solvent extraction of chromium showed that, although many systems exist for extraction of Cr VI, only a very few reagents have been found to extract Cr 111. The extraction of Cr III by di-(2-ethyl hexyl) phosphoric acid has been reported by Kimura.' A straight-line dependence of slope —2 was observed between log D,, and the log mineral acid concentration at constant extractant concentration. Since the slope of this plot reflects the charge on the ion extracted, it must be concluded that a hydrolyzed species of Cr III is being extracted. Carboxylic acids generally do not form extractable complexes with Cr III but di-isopropyl salicylic acie does extract Cr 111. Simple acid backwashing of the organic phase, however, failed to remove the chromium. Similar difficulty in backwashing was found by Hellwege and Schweitzer8 in the extraction of Cr I11 with acetyl-acetone in chloroform. The extraction of Cr 111 from chloride solutions by alkyl amines has been reported4-' but the maximum amount of extraction achieved in these studies did not exceed 10%: From sulfate solutions, however, Ishimori" has shown that appreciable amounts of Cr I11 were extracted by amines. The amines used were tri-iso-octyl amine, Amberlite LA-1 (a secondary amine, Rohm & Haas) and Primene JMT (primary amine, Rohm & Haas). The efficiency of extraction with regard to amine type was primary>secondary> tertiary. Appreciable extraction of Cr I11 was recorded for Primene JMT as the aqueous phase acidity tended to zero. The major difficulty with Cr I11 in solvent extraction systems stems from the nonlabile nature of the ion in complex formation. This accounts for the slow rate of extraction generally experienced and the difficulty encountered in backwashing the Cr I11 from the organic phase in the case of liquid cation exchangers. Consequently, the possibility of extraction of Cr I11 as a complex anion is attractive since the backwashing problems should be minimized in this way. From published data, it appeared that the extraction of chromium from sulfate solutions of low acidity by primary amines afforded the best chance of success for a useful solvent extraction system for Cr iii This paper presents the results of a study of the extraction of Cr I11 from sulfate solution by Primene JMT and examines the application of such an extraction procedure for the recovery of chromium from liquors containing iron and copper. Experimental Chromium solutions were prepared from chrome alum in sulfuric acid and sodium sulfate so as to maintain a constant concentration of sulfate ion of 1.5 molar. Solutions of Primene JMT were prepared in xylene and the amine equilibrated with sulfuric acid/sodium sul-fate solutions, of the same acidity as the chromium solution, until there was no change in acidity between the initial and final aqueous phases. The solutions of Primene JMT conditioned in this way were then used for the equilibration experiments. Equilibrations at 25°C were carried out in stoppered conical flasks shaken in a thermostat; equilibrations at all other temperatures were carried out in stirred flasks in a thermostat. After equilibration, the phases were separated and analyzed for chromium. In the tests on the rate of extraction, small samples of equal volume of both phases were withdrawn from time to time and the chromium distribution determined. The chromium analyses were carried out either coloi-imetrically using diphenyl carbazide, or volu-metrically using addition of excess standard ferrous ammonium sulfate and back titration of the excess iron with potassium dichromate. The oxidation of Cr 111 to Cr VI in the case of the raffinate solution was effected by boiling with potassium persulfate in the presence of silver nitrate and, for the backwash solution, by boiling with sodium hydroxide and hydrogen peroxide. Results Preliminary experiments indicated that extraction results were effected by the age of the chromium solution, higher distribution coefficients being obtained with solutions which had been allowed to stand for some time. Consequently a stock solution of chrome alum, 10 m moles per 1 Cr I11 in 1.4 M Na,SO,/O.l M &SO,,

Jan 1, 1971

By Arthur Baker

The orebodies are long bedding-plane lenses of chalcopyrite and sphalerite, associated with garnetite masses. Most of the orebodies are within a 50-ft thickness of Cambrian limestone; other Paleozoic limestones and dolomites are locally metamorphosed but only slightly mineralized. Pre-mineral faults are numerous, but shallow folds were the main ore-localizing structures.

Jan 12, 1953

By Louis C. McCabe

The control of dusts and fumes of submicron size is involved in many process industries. This paper presents in tabular form the quantitative data from a number of metallurgical operations and discusses allowable discharge in terms of effluent-weight ratio. Typical installations for recovery of stack effluents are cited.

Jan 9, 1950

By Milton E. Wadsworth, W. Martin Fassell, William H. Dresher

A study of the rate of dissolution of molybdenite (MoS2) in alkaline solution was carried out under carefully controlled conditions. Effects of temperature, oxygen over-pressure, and KOH concentration were evaluated. Studies were made in the temperature range 100°C to 175°C and in the pressure range 0 to 700 psia of oxygen. Under these conditions molybdenite was found to leach according to a linear mechanism. Both oxygen over-pressure and KOH concentration were found to control the rate of leaching. The mechanism has been explained in terms of adsorption of oxygen at the molybdenite surface followed by configurational rearrangement of the adsorbed molecules. The hydroxyl ion dependency is believed to be diffusion-controlled. Laboratory batch studies have shown that molybdenite can be readily dissolved in alkaline solutions under moderate conditions of temperature and pressure. Commercial application of this process to the production of ferro-molybdenum and molybdenum chemicals is promising in view of the ease of dissolution of molybdenite and the relatively noncorrosive conditions involved in the process. HIGH temperature-high pressure techniques have long been used to great advantage in the organic chemical industry, the petroleum industry, and the paper industry. Only recently, however, have these methods been used to extract metals from their ores on a commercial scale. The Chemical Construction Corp., together with interested producers of nickel and cobalt, has done much to develop methods of producing nickel and cobalt powders by the use of high temperature-high pressure techniques.' The Howe Sound Co. is currently operating a plant near Salt Lake City in which the new Chemical Construction Corp. technique is applied to cobalt-arsenic sulfide concentrates. In this method the concentrates are leached in a dilute solution of sulfuric acid under air pressure at a high temperature. Near Edmonton, in Alberta, Canada, the Sherritt Gordon Co. is also using the new method in conjunction with its ammoniacal leach process.' National Lead Co., at Fredricktown, Mo., is operating a process similar to that of Howe Sound. In spite of the rapid growth of high temperature-high pressure hydrometallurgical processes, there has been very little work done on fundamental principles involved in this type of process. Conse- quently the literature lacks any significant data in this field. Oxidation of pyrite,3 phalerite,4 galena,5 and recently molybdenite" in alkaline solutions has been reported to some extent. This investigation was initiated, therefore, to broaden the application of high temperature-high pressure hydrometallurgy and also to contribute some insight into the basic mechanisms of oxidation in an aqueous medium under these conditions. In addition to the immediate consequences of these processes much valuable information remains to be learned about fundamental reactions when they are carried out at temperatures and pressures slightly higher than those normally encountered. Leaching of molybdenite by alkaline solutions under oxygen pressure has recently been reported in the Russian literature by E. S. Usataya,8 who found that leaching rate increased with an increase in the pH of the solution—the strongest effects being observed at a pH of 10—and also with an increase in temperature. Usataya also has reported the formation of a protective film on the surface of the molybdenite when the leaching solution was weakly alkaline, neutral, or acidic. He believes that this oxidation process explains the migration of Mo+ + in the oxidation zones of molybdenite ore deposits and the subsequent impoverishment of the ores. Equipment: The high temperature-high pressure reaction unit used in this work was especially designed for kinetic studies of this nature, emphasis being placed on accuracy of measurement and precision of control. As details of the unit's construction and operation have been discussed elsewhere,7 Only basic features and principles of operation will be discussed at this point.

Jan 1, 1957

By Dorsey Hager

THE possibility of oil and gas production in Alabama has been little considered as yet. Gas and some oil have been found in northwestern Alabama, near Birmingham, in the Pennsylvanian beds, but the oil and gas possibilities in the Cretaceous beds are not generally appreciated. The recent activity of oil companies in that State has attracted much attention, and in this paper the main structural and the general stratigraphic features are described. Four favorable areas are outlined. These contain folds of major interest. There are other favorable areas which have not been mapped. Commercial pools discovered in this area would have the advantage of being near tidewater. Mobile, Ala., on the Gulf, of Mexico, would be the logical site for refineries and shipping facilities. A pipe line could readily be laid to that city from the Hatchitigbee and the Jackson areas. The logical outlet for the Geneva and the Gordon areas would be Panama City, Fla., on the Gulf of Mexico.

Jan 2, 1918

By Oliver C. Ralston

A definite field of usefulness has developed for the brine-leaching processes of removing lead from ores and other products, so this paper reviews the developments, both in practice and in research, that have taken place since the publication of two earlier papers on this subject.' Several commercial plants are now in operation and a number of semi-commercial test plants have been operated in an effort to determine the limitations of brine leaching and to compare the results with other forms of treatment. Briefly, the brine leaching of lead depends on the fact that lead chloride and lead sulfate are soluble in saturated sodium-chloride solutions. In dilute brines, the solubility of the lead salt is less than in pure water; but in the strong brines, the solubility is greater than in pure water due, supposedly, to the formation of a double sodium-lead chloride. This is seen in Fig. 1, which shows the results of M. Demassieux2 on the solubility of lead chloride in sodium-chloride solutions of different concentrations and at three temperatures. The curves are not those given by Demassieux but are calculated from his results in order to convert them to units common in metallurgical work. The right-hand branch of each curve shows that if the solution is kept in contact with solid sodium chloride the lead chloride can be almost entirely displaced from solution, but that brines which are saturated with sodium chloride, but are not in contact with the solid salt, have a very high solubility for lead chloride. The diagram gives the analysis of the solution in grams of lead per liter, although the substance actually in solution is lead chloride. At 100" C. as much as 100 gm. of lead per liter can be obtained; but at lower tem-

Jan 1, 1924

By AIME AIME

THIS year the Chairman of the Institute's Iron and Steel Division is THIS William Anderson Haven, better known to the membership generally as Bill Haven. The Division Chairman is an individual endowed with a broad perspective of the ferrous metal industry he result of his earlier experiences as a successful operating man in the working and management of blast furnaces and his later experiences as an engineering-consulting executive concerned with the design and erection of and steel works throughout the world. William A. Haven was born to iron steel in the Pittsburgh district on ;. 1, 1888, and in due time--or in 1909 graduated from Penn State with a Bachelor degree in industrial chemistry.

Jan 1, 1944

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By P. H. Brace

THE study of the relations between gases and metals is one of perennial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 lb. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale or which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experimental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urge any hypothesis at this time.

Jan 1, 1928

By W. D. Robertson, H. H. Uhlig

INTRODUCTION THE intermetallic compounds Mg2Sn and Mg2Pb are two of the important series of stoichiometric compounds pounds which magnesium forms with elements of the fourth group of the periodic system, Since there is a complete series, of compounds, all possessing the same comparatively simple structure, a unique opportunity is presented to study their properties with respect to increasing atomic number of the anion as it varies from silicon and germanium, through tin and lead. The present work deals with the two lower members of this group, and it is hoped eventually that additional data regarding the silicide and germanide will be obtained. The results of such a complete study provide part of the essential basis for the empirical correlation and theoretical treatment which, in other systems, has contributed to an understanding of intermetallic compounds and the metallic state in general. Some experimental data are already available in the literature, However, they re fragmentary and limited in significance owing to the methods of preparation employed and the impure materials available at the time, It was our objective, therefore, using pure metals and improved metallurgical methods of preparation, to produce stoichiometric compounds of high purity for the study of their electrical and chemical properties. We felt that a detailed investigation of chemical properties, about which relatively little is known, combined with electrical properties, would be a significant contribution to the understanding of these compounds and in particular to the mechanism of corrosion associated with types of bonding in alloy systems. The chemical studies are reported elsewhere. PREVIOUS INVESTIGATIONS Previous work concerning the electrical properties of these compounds was undertaken in connection with the establishment of the two phase diagrams which are available in Hansen1 and Beck,2 The first comprehensive investigation of the electrical conductivity of magnesium-tin and magnesium-lead alloys was made by Kurnakov and Stepanov.3 This was followed by Grube and Vosskühler4 who studied electrical conductivity and thermal expansion over a wide range of temperature and who, unlike Stepanov, appreciated the significance of the large solid solubility of tin in magnesium and took some precautions to obtain an equilibrium state. However, at the time these investigations were made, neither pure magnesium nor

Jan 1, 1948

By A. F. Lucas

Introduction BELLE ISLE, located in the low sea marshes near Atchafalaya Bay, is the southeasternmost of the famous Five Salt Islands of Louisiana. Rising about 80 ft. (24 m.) above the level of the surrounding marsh and being some 800 acres (323 ha.) in extent, it constitutes a striking landmark on the low Gulf coast, and since the eighteenth century, when it played an important part in the operation of the buccaneers, it has been intermittently frequented by man. In 1897, the writer discovered the great mass of salt that underlies the island and shortly afterward pub-lished a brief account of the geology of Belle Isle and the neighboring salt islands.' In that paper he described principally the salt, but pointed out also the occurrence of petroleum and of sulphur in the strata above the salt. Since that time the island has been extensively explored by the drill, and the developments up to 1908 have been described by Veatch2 and Harris," and Knapp.4 The writer's early conclusions as to the probable presence of sulphur in considerable quantity have been confirmed by the later drilling, some of the wells having found quantities of gas containing sulphur dioxide and a number of sulphur-bearing strata as well. Under the stimulus of the present keen demand for sulphur for war purposes, a syndicate of New York capitalists was recently formed to explore the sulphur resources of the island in more detail. Under the writer's direction, six wells were drilled for this syndicate during the winter of 1916-17. The present paper presents briefly the results of this work and sums up the present knowledge of the geology of this highly interesting locality.

Jan 9, 1917

[NORTH AMERICA UNITED STATES ALABAMA Bessemer Coston, Otis D., Jr. Birmingham Cord, Richard M. Dismukes, Edward B. Pagel, Herbert E. Citronelle Mason, Seeber William Mize, Frank W. Perrin, Huey P. Fairhope Ruffles, William R., Ill Huntsville Waggoner, J. B. Mobile Hankins, James D. Petroutson, Peter C. Montgomery Crenwelge, Joe Ed Tuscaloosa Mason, William L. University Jones, Walter B. *Ricnards, Edward F.]

Jan 1, 1961

By D. V. Carter, Dan C. Williams, Franklin M. Hackbusch

During 1939 little of consequence happened in East and East Central Texas in the way of oil discoveries. At the end of the year, there were 47 oil and gas fields in the district. Twelve other fields, 11 oil and one gas, have been abandoned. The ranking fields in order of the number of completions for the year were East Texas, Talco, and Rodessa (Texas portion). There were 511 oil wells (distillate wells included), 32 gas wells, and 257 dry holes completed in the district. Exploration, Discoveries and Extensions During the year, 113 exploratory wells were drilled, the same number as in 1938; four oil fields and one gas-distillate field were discovered. Perhaps the most important discovery, which has been named Barron field, was that of M. Samuel et al., No. 1 Barron in Limestone County. The wells in this field are of the gas-distillate type. Other than the Talco and Sulphur Bluff fields, which produce oil from the Paluxy sand (Upper Trinity), this is the first field on the Corsicana-Mexia fault zone to obtain commercial production from deeper Trinity strata. This "pay" is the Petit lime of the Lower Glen Rose of the Trinity group. The four oil discoveries were: Redland, Angelina County; Bazette, Henderson County; Rowe and Baker, Henderson County; and Marion County Shallow in Marion County. It is believed that the Bazette field, Navarro County, represents an extension of the Flag Lake field. For details concerning discoveries, extensions and important wildcat wells drilled during 1939 see Table 2. Production and Proration The district produced 175,053,729 bbl. of oil (distillate production included) which is a decrease of 4.0 per cent from the 182,369,484 bbl. (distillate production included) produced during 1938. The district's production for the year 1937 was 208,594,453 bbl. The East Texas

Jan 1, 1940

By D. V. Carter, Dan C. Williams, Franklin M. Hackbusch

During 1939 little of consequence happened in East and East Central Texas in the way of oil discoveries. At the end of the year, there were 47 oil and gas fields in the district. Twelve other fields, 11 oil and one gas, have been abandoned. The ranking fields in order of the number of completions for the year were East Texas, Talco, and Rodessa (Texas portion). There were 511 oil wells (distillate wells included), 32 gas wells, and 257 dry holes completed in the district. Exploration, Discoveries and Extensions During the year, 113 exploratory wells were drilled, the same number as in 1938; four oil fields and one gas-distillate field were discovered. Perhaps the most important discovery, which has been named Barron field, was that of M. Samuel et al., No. 1 Barron in Limestone County. The wells in this field are of the gas-distillate type. Other than the Talco and Sulphur Bluff fields, which produce oil from the Paluxy sand (Upper Trinity), this is the first field on the Corsicana-Mexia fault zone to obtain commercial production from deeper Trinity strata. This "pay" is the Petit lime of the Lower Glen Rose of the Trinity group. The four oil discoveries were: Redland, Angelina County; Bazette, Henderson County; Rowe and Baker, Henderson County; and Marion County Shallow in Marion County. It is believed that the Bazette field, Navarro County, represents an extension of the Flag Lake field. For details concerning discoveries, extensions and important wildcat wells drilled during 1939 see Table 2. Production and Proration The district produced 175,053,729 bbl. of oil (distillate production included) which is a decrease of 4.0 per cent from the 182,369,484 bbl. (distillate production included) produced during 1938. The district's production for the year 1937 was 208,594,453 bbl. The East Texas

Jan 1, 1940