Search Documents

By R. C. Hall

In the present work, experiments determined the effect of the order-disorder reaction near the Fe,Al composition on the magnetic anisotropy and magnetostriction of single crystals: A material which is more difficult to magnetize in one direction than in another is anisotropic, that is, the ease with which ferromagnetic materials may be magnetized in different crystallographic directions determines the anisotropy. Two investigators have estimated the anisotropy of the aluminum iron alloys from poly-crystalline data;1,2 however, these estimates should not be considered to be reliable. Siege1 made two accurate measurements of the first anisotropy constant* from single crystals of 4.0 wt pct aluminum sotropy throughout the ferromagnetic aluminum iron system have been described. These results were obtained from single crystals which were slowly cooled and, hence, ordered near the Fe3Al composition.4 Magnetostriction is the change in length per unit length resulting from applying a magnetic field to a ferromagnetic material. For the purpose of this report, the saturation magnetostriction was measured. This is the maximum change in length per unit length resulting from an applied magnetic field large enough to saturate the material in a given direction. This magnetostriction has been determined for single crystals of the ferromagnetic aluminum-iron system.' The crystals near Fe3Al were also ordered. PREPARATION AND TREATMENT OF SINGLE CRYSTALS Single crystal bars were grown from the melt.' The raw materials for these crystals were iron and aluminum of 99.9 and 99.99 pct purity, respectively. From the bars, crystals in the shape of circular

Jan 1, 1959

By R. T. Mishler

Silver-gold. mine, in northern Mexico, with arrow veins in rhyolite. One fourth area developed has been ore. Deposits average 20 in. wide and 73 oz. silver per ton; diluted in mining to 40 oz. per ton. Developed by drifts and raises at 100-ft. intervals. Samples cut every 5 ft. Ore and waste sampled separately to make combined stoping width 3 or 3 1/2 ft. Ore reserves figured to sloping width; high assays not modified. Tonnage and assay of ore extracted higher than estimates. Ore stoped principally by cut and fill method. Cars from each stope counted and sampled. Cars check tonnage to concen¬trator within 1 per cent.; silver assay 9 per cent. high. Tonnage and assay from scopes corrected to agree with feed to concentrator. Profit or loss for each slope estimated monthly. THE Lucky-Tiger mine is a silver-gold property, situated at El Tigre, in the northeastern part of Sonora, Mexico, at, an elevation of 6000 ft. in the Sierra Madre Mountains. It is 30 miles by wagon road from the Esqueda station on the Nacozari railroad. Since its discovery in 1903, the mine has produced forty million ounces of silver. The ore has averaged 40 oz. silver and 0.25 oz. gold per ton. Copper, lead and zinc have been of minor importance, having averaged 0.4 per cent., 1.1 per cent., and 1.5 per cent., respectively. The richness of the ore,, combined with its occurrence in narrow veins, required the use of the more expensive methods of mining.

Jan 2, 1925

By D. I. Bardos, Paul A. Beck

A MARK, Boren, and westgrenl in their X-ray diffraction study of manganese alloys with 10 to 25 at. pct Si reported the occurrence of a phase with complex crystal structure in a Mn + 14.5 at. pct Si alloy after annealing at 800° or at 600°C. Recently Kuzma and Gladyshevskii2 identified Mn6Si as an R phase,3,4 the second binary R phase known. (A binary R phase was previously found in the Mn-Ti system by Waterstrat.5) A ternary R phase was reported earlier0 near the Mn-Si binary border of the Ti-Mn-Si system at 1000°C. In the light of the Russian work it now appears that this "ternary" R phase may be in fact an extension of the binary (Mn6Si)R phase. As already found by Amark, Boren, and Westgren, the corresponding binary phase is absent at 1000°C; the effect of titanium is evidently to stabilize it up to higher temperatures. In a recent paper Wieser and Forgeng7 gave the boundaries of this binary phase, which they referred to as 6. In order to re-examine the identity of this phase, an alloy of Mn + 14.5 at. pct Si was prepared by induction melting in helium atmosphere and annealed for 3 days at 800°C. The powder pattern, taken with an asymmetrical focusing camera of large dispersion and shown in Table I, was found to be that of the R phase, in agreement with the results of Kuzma and Gladyshevskii. For comparison, Table I also lists

Jan 1, 1965

By George Espey, George Sachs, G. B. Kasik

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually have been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,' the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin3-5 and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between

Jan 1, 1942

By G. B. Kasik, George Sachs, George Espey

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually have been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,' the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin3-5 and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between

Jan 1, 1942

By Milton E. Wadsworth, John N. Ong, W. Martin Fassell

The temperature and oxygen concentration dependence on the reaction of sphalerite in oxygen at pressures from 6 to 640 mm Hg have been investigated in the temperature range 700° to 870°C. Sphalerite has been found to oxidize linearly over this entire temperature and pressure range. At higher rates, considerable self-heating was observed. The dependence of the oxidation rate on the oxygen concentration may be expressed by: Rate = k' where k' is the specific rate constant and 0 = K1[O2]/(1 + KI[O2]), where K1 is the equilibrium rate constant for the adsorption of oxygen on sphalerite. Values of the activation energy and the enthalpy of adsorption were found to be 60.3 and —59.6 kcal per mol, respectively. Data have been presented that indicate conditions under which either a sulphatizing or an oxidizing roast may be obtained. ROASTING processes have been employed in the metallurgy of a great number of basic metals in use today. Until recently, however, little attempt has been made to deduce the fundamental mechanism by which oxidation takes place. Structural changes upon oxidation have been investigated1 = and thorough work has been performed with regard to the reaction products and the thermodynamics of the oxidation reactions. The objective of this investigation was to determine the rate of oxidation of sphalerite and to apply the absolute reaction rate theory in the theoretilcal interpretation of the experimental results." "O Description of Apparatus The apparatus contains the following features: 1—a furnace with gas system, 2—an autographic weighing system, and 3—a temperature control system. Furnace With Gas System—The furnace was mounted by a yoke on each end and was free to travel up and down on steel guide rods, permitting the introduction and removal of samples from the apparatus with minimum difficulty. The furnace was heated by three sections of Kanthal wire wound externally on a zirconia tube and insulated with Fiber-frax. Pure gases or mixtures of gases were introduced into the lower end of the furnace through two flowmeters, a mixing chamber, and a gas-tight sparger, Fig. 1. The gaseous products of the reaction and the unused gases were prevented from escaping to the atmosphere by maintaining a small negative pressure on the system. This procedure permitted air from the outside to enter through the small an-nulus around the quartz suspension fiber and prevented the escape of the internal gases. Autographic Weighing System—The autographic weighing system consisted of an adapted gold balance, a photoelectric circuit, and a weight recorder, Fig. 2. The sample was suspended from one end of the balance beam by means of a platinum chain outside the furnace and a long thin quartz fiber on the inside of the furnace. On the other end of the balance beam, the necessary weights were added to counterbalance the sample. In addition, a calibrated chain was added to the balance which was linked directly to the weight recording unit. Control was effected by means of a photoelectric circuit." A parallel beam of light from a strong source was directed onto a small front-surfaced aluminum mirror mounted in the middle of the balance beam and then to a front-surfaced mirror mounted on the ceiling of the room. The beam was then reflected onto a front-surfaced right prism at a distance of 9 ft from the balance

Jan 1, 1957

By B. B. Rath, Hsun Hu

Rates of migration of large-angle boundaries have been studied in zone-refined aluminum crystals, defonned 80 pct by rolling in the (110)[112] orientation at -78°C followed by a recovery anneal at 80°C. Artificially nucleated grains show a marked variation. by an order of magnitude, in their growth rates in different directions. The average activation energy for the migration of all boundaries was found to be about 16,000 cal per mole. The anisotropy of the boundary migration is rationalized on the basis of the boundary structure. It has been observed by Beck and HU,1 Kohara el al,2,3 and Czjzek and Haessner4 that recrystallized grains formed upon annealing Of deformed sing1e crystals of aluminum show anisotropic growth characteristics. Kohara et al. found that single crystals rolled in the (110)[112] orientation, when random nuclei were provided on one side of the crystal by rubbing with emery paper and annealing, developed a sharp recrys-tallization texture on the other side of the crystal upon further annealing. This sharp recrystallization texture consisted of four components, which were related to the deformation texture of the crystal, i.e. (110)[112], by rotations of ±40 deg around each of the two common [ 111] axes' They also noted that recrystallized grains were elongated in directions perpendicular to either of these two common [1111 axes. They attributed this anisotropic growth to the difference in the rate of self-diffusion or diffusion of impurity atoms along the tilt and the twist boundaries. A somewhat similar investigation was conducted by Czjzek and Haessner4 On strained single-crystal sheets Of alum- inum. These authors claimed that the matrix structure of the deformed crystal had a greater effect on the growth anisotropy of the recrystallized grains than did the boundary orientation itself. In the present investigation quantitative measurements of the rate of grain boundary migration in anisotropic growth have been made in zone-refined aluminum (99.9999+pct pure) crystals deformed 80 pct by rolling in the (110) 112] orientation. Crystals of this particular orientation were chosen because of the following desirable features: 1) the crystal does not change its orientation during rolling; 2) the rolling plane contains all the significant crystallographic directions; and 3) when annealed, following deformation, the crystal does not re-crystallize spontaneously but polygonizes to a stable and homogeneous structure. Hence, the initial orientation of the crystal and a constant strain energy in the matrix can be maintained during subsequent grain boundary migration studies. It is essential to keep the driving force constant for the study of boundary mobility.5 EXPERIMENTAL PROCEDURE A cylindrical single crystal of 1 in. diam was grown by the Bridgman method in a high-purity graphite mold. The resistance ratio, R(4.2°K) /R(298°K) , of the grown crystal was approximately 2.0 x 10-4. A number of slices, 1/4 in. thick, were cut from the crystal along the (110) plane and were mechanically and electrolyti-cally polished to remove the strained surface layer. The crystals were then rolled along the [112] direction to 80 pct reduction in thickness at -78°C. To minimize surface friction, the crystals were rolled between two layers of 0.005-in. teflon sheet. Rolling was interrupted, prior to completion, to remove the surface layers and the edges by electropolishing. These and similar precautions in handling the rolled crystals

Jan 1, 1967

By James Norman

SPODUMENE is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content it might be a desirable constituent of glass batches. The use of spodu-mene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components.1 The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manga-nese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li20 on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston, ? the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2,3 The methods described in the second publication' did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted.

Jan 1, 1940

By N. F. Schulz, H. A. Lex, J. D. Zetterstrom

A green ball of iron ore faces many perils from the time it is formed until it finally emerges from the pelletizing furnace as a hardened pellet. For instance, if the rate of heat transfer into a ball is sufficient to produce vapor from either the free or combined water more rapidly than it can escape at a tolerable pressure, the ball may split, spall, or even explode, a failure commonly known as decrepitation. To avoid such failures, one must either limit the rate of heat transfer during the drying and preheating stages, at the expense of production rates, or improve the decrepitation resistance of the green balls. The latter remedy may often be accomplished through changes in ore preparation, balling procedures, or the judicious use of binders or other additives. INTRODUCTION Pelletization has become established as an especially desirable method for the agglomeration of fine taconite concentrates and it promises to be equally satisfactory for improving the physical structures of certain natural ores. A high-quality pelletized iron ore consists of uniformly sized spheres, usually about 1/2-in. diam, which are strong enough to resist abrasion and breakage during handling and which reduce well without disintegration in the blast furnace. The unfired agglomerates, "green balls", are subject to several destructive effects that must be avoided or minimized if a high-quality product is to be obtained by pelletization. Among these are abrasion and impact deformation or breakage during handling of the wet green balls, deformation and breakage by compressive forces in the bed of ore in the pel-letizing furnace, decrepitation during drying and preheating, wind erosion, and radial cracking at firing temperatures. Moisture condensation from the warm saturated gases downstream from the drying zone on wet, cool balls may cause bed collapse if it becomes excessive. Decrepitation is defined as the sudden disintegration of green balls, usually with an audible pop, that occurs when they are heated too rapidly during the drying or preheating stages of the pelletization process. The extent of ball disintegration may vary from merely splitting off a small fragment to almost total disintegration into the original ore particles making up the ball. Such ball destruction results in a decreased yield of pellets, and the fragments, which also tend to interfere by obstructing the gas flow through the bed, must eventually be screened from the fired product and recycled. The closely related type of ball failure that sometimes occurs during the high temperature firing stage, resulting in radial cracks without fragmentation, was not considered to be decrepitation for the purpose of this investigation. Failure by decrepitation is not usually a serious problem in the pelletization of taconite concentrates. The problem is significant, however, in the pelletization of some natural ores, especially those containing hydrous iron oxides. In some instances, economicd production rates cannot be maintained if the drying and preheating rates are slowed down enough to avoid decrepitation. OBJECTIVES This investigation was undertaken to: (1) Develop a practical laboratory means for quantitatively measuring the tendency for green balls to decrepitate in iron ore pelletizing furnaces, and (2) Investigate the causes and cures of ball decrepitation. MATERIALS Two iron ores were used in the work reported here: a taconite concentrate at 90% minus 325 mesh, containing 65.0% Fe, 8.4% SiO2, and no loss-on-ignition; and a crude oxidized ore at 54% minus 325 mesh, containing 59.1% Fe, 3.6% SiO2, 1.1% A12O3, and 9.5% loss-on-ignition. For a special test of effect of particle size distribution on decrepitation, two other

Jan 1, 1967

By J. Blodget Britton

During the last three or four years I have had occasion to examine, chemically, various samples of matter commonly called flue-dust or cinder, found deposited in the flues and hot-blast chambers and under the boilers of blast furnaces, and also in the flues and under the boilers of puddling and boiling furnaces. Recently several of these examinations mere made quite in detail, and as the results reveal, I believe, information of no inconsiderable importance, I am induced to communicate them to this Institute. A sample of deposit obtained from the flues of one of the blast furnaces at the works of the Phœix Iron Company, at Phœnixville, Pa., was found to have the composition given in Column I of the following table: I. 11. 111. Composition of Dust from Dust from Dust from Deposits. Blast Furnace. Puddling Furnace. Boiling Furnace. Protoxide of iron,... 1.51 3 08 1.18 Peroxide of iron,... 20.21 33.29 41.00 Alumina,....6.57 12.89 7.54 Lime,.....3.98 .48 .61 Magnesia,.....69 .09 .19 Protoxide of manganese,. . 1.66 .39 .12 Oxide of zinc,....2.84 ........ Oxide of copper,. .. ..06 ........ Silicic acid,....36.00 40.69 38.99 Sulphuric acid,... 7.55 .43 Phosphoric acid,..94 ..94 Arsenious acid,. .. .38 Antimoniousacid,... trace.......... Chlorine,....03 ..03 Cyanogen,.....09 ........ Ammonia,.... trace......... Pottlsh with some sodn,. .. 16.61 ........ Carbonic acid,. .. .. .59 ........ Alkalies, undetermined matter, and loss,.......29 4.49 6.96 100.00 100 00 100.00 Metallic iron,. 16.31 25.70 29.64 Phosphorus,. .. .. .41* 1.55† 1.30†

By R. M. Waterstrat, B. N. Das, Paul A. Beck

The central region of the Ti-Mn system was studied by means of x-ray diffraction and metallography. The following intermediate phases were found: an MgZn2-type Laves phase having a wide range of homogeneity, the p-phase of unknozvn structure, and the + -phase with a large tetragonal unit cell, stable at 930°C and lower temperatuves. MaYKUTH, Ogden, and jaffee1 determined the soh-inh bility limits of manganese in and titanium. They also confirmed the structure of the intermediate phase TiMn2 which was previously identified as a Laves phase of the MgZn2 type.2 In the equiatomic region they found an additional intermediate phase, y, which presumably formed by a peritectic reaction at approximately 1200°C. This last observation was disputed by Rostoker, Elliott, and McPhers0n,3 who reported the formation of TiMn by a peritectoid reaction between 900" and 1000° C, but found no evidence of any intermediate phase other than the Laves phase at higher temperatures. Elliott and Rostoker4 reported furthermore that the X-ray diffraction pattern of TiMn could be identified as that of a o phase, although their data were not consistent with this inter~retation. Margolin and Ence6 presented X-ray diffraction data for the and TiMn, phases, and obtained metallographic indications for the existence of additional intermediate phases. They concluded from metallographic observations that two Laves phases are formed, separated by another phase, designated as &. A phase diagram for the Mn-Ti system has recently been published by Savitskii and Kopetskii,' which shows considerable disagreement with the work of Hellawell and Hume-Rothery,' in particular with regard to the terminal solid solutions based on the allotropes of manganese. The present investigation was undertaken primarily to clarify the phase relationships in the equiatomic region of the Ti-Mn system. The metals used in preparing the alloy specimens Were iodide titanium and electrolytic manganese, the latter having a nominal purity of approximately 99.9 pet. The electrolytic manganese was covered with a thick coating of a brown manganese oxide which was reduced by heating the manganese flakes for several hours at a temperature of 1100°C in an atmosphere of dry hydrogen. Three alloys, see Table I, were made using sponge titanium and manganese not treated in hydrogen. The alloys were prepared by arc-melting in an atmosphere of helium or argon. The composition of each alloy was calculated by assuming that the entire weight loss during melting was due to evaporation of manganese. Subsequent chemical analysis of certain alloys indicated that the compositions calculated in this manner were usually correct within 1.4 pct, as shown in Table I. All alloy specimens were wrapped in molybdenum foil before sealing them in silica tubes containing argon at a pressure of 1 atm at the annealing temperature. After quenching in cold water, the alloy specimens were bright and clean, with no evidence of any surface reaction. The alloys listed in Table I were examined metallographically, using an etchant consisting of 20 pet HNO3, 20 pet HF, and 60 pet Glycerine. powder for X-ray diffraction examination was prepared by crushing a portion of each annealed alloy

Jan 1, 1962

By AIME AIME

Council.* PRESIDENT OF THE COUNCIL. JOHN HAYS HAMMOND NEW YORK, N. Y. (Term expires February, 1908.) VICE-PRESIDENTS OF THE COUNCIL. HENRY M. HOWE NEW YORK, N. Y. J. B. GRANT DENVER, COLO. JAMES D. HAGUE NEW YORK, N. Y. (Term expires February, 1908.) SAMUEL B. CHRISTY BERKELEY, CAL. JOHN A. CHURCH NEW YORK; N. Y. New PERSIFOR FRAZER PHILADELPHIA, PA. (Term expires February, 1909.)

Mar 1, 1907

By W. B. Plank

RETURNS already received from a current survey of the enrolment of students in the mineral technology schools indicate a degree of activity and prosperity in those schools never before equalled. The returns are as yet too meager for accurate analysis, but those at hand point LO considerable increase in the metallurgical and petroleum engineering groups, and indicate that the total of 5011 two years ago in the United States schools will be substantially increased. Generally speaking, the enrolment is not only maximum in quantity but optimum in quality. Better income has sent the boys back to school, but the improved employment conditions have somewhat reduced the number of graduate students. Laboratories are commonly filled to capacity, in some instances overcrowded. Increased enrolment of foreign students from both Canada and South America is noticeable.

Jan 1, 1937

By G. F. Comstock

H. M. BOYLSTON, Cambridge, Mass.-It might be asked, since this test is so simple, why it was not discovered before. It seems to me the explanation is that when we have used the sodium picrate solution, it has .generally been on a very, high-carbon or hypereutectoid steel; to detect . the presence of free cementite, and when we have looked for sulphides, it

Jan 4, 1917

By O. D. Gaither

This paper is an analytical study of the flow of fluids through small vertical conduits. Small conduits are defined as 11/4-in. nominal diameter tubing size and smaller, and approximately twice this area for annular conduits (i.e., 1- X 21/2-in. annulus and smaller). Experimental data are presented for the 1-X2-in. and 11/4- X 2%-in. annuli, and the I-in. and 11/4-in. tubing, since these represent the small conduit sizes and configurations generally encountered in oilfield applications. Data have been gathered for these conduits for single-phase water, single-phase gas and two-phase water-gas mixtures, with particular emphasis on high gas-liquid ratios. Water rates in excess of 2,000 BID and gas rates in excess of 2.5 MMcf/D, and two-phase flow ratios in between these two, represent the scope of the data gathered. Existing equations have been applied to predict flowing pressures and compared with experimental data. New correlations have been developed. INTRODUCTION The increased economic pressure on the domestic oil industry in the United States has constantly required the use of new techniques and equipment designed to reduce the cost of finding and producing oil and gas. Since tangible items are most readily apparent in economic analysis, the advent of lower-cost well completions was inevitable. One of the methods used to reduce costs which has received widespread attention is the slim-hole completion technique where tubing is used as the well casing and in which small conduits are used for tubing if necessary. Small conduits, defined by Kirkpatrick1 as "11/4-in. diameter nominal tubing and smaller for tubing flow and less than twice the 11/4-in. diameter nominal tubing internal flow area for annulus flow", have also found widespread usage as siphon strings for de-watering gas wells and as "kill" strings in deep high-pressure oil and gas wells. The growing use of small-diameter tubing has resulted in an increased need for development of improved methods to measure or predict flowing bottom-hole pressures since the physical dimensions generally preclude the use of subsurface-recording pressure gauges. Even in the cases where small bombs are available, the relatively high velocities encountered at nominal flow rates make it necessary to use excessive weight bars or special hold-down devices. Attempts to use recognized correlations to accurately predict flowing or gas-lift performance in wells equipped with small conduits have been generally unsuccessful. Insufficient field data were available to allow the development of a correlation on this basis, and an experimental approach was applied in an attempt to obtain a workable relation. The experimental approach used to obtain the data presented in this paper was actually a compromise between a field installation and a laboratory study. A test well 1,000 ft in length was used to obtain flow data on single-phase liquid, single-phase gas and two-phase water-gas flowing mixtures. Liquid rates up to 2,200 B/D and gas rates up to 3 MMcf/D were used in the single-phase flow studies. Two-phase flow rates from 100 to 600 B/D with gas-liquid ratios from 500 to 8,000 cu ft/bbl were recorded. Experimental data were obtained for single- and two-phase flow through 1-in and 11/4-in. nominal tubing, and through the annuli between 1- and 2-in. and 11/4- and 2%-in. nominal tubing strings. Experimental results for the two-phase flow are compared to the Poettmann-Carpenter correlation2 which is widely used as a comparative standard for development of multiphase flow predictions in flowing and gas-lift wells. Correlations developed by Tek,3 Baxendell and Thomas" were also investigated. The experimental data recorded herein fell in between the two flow regimes as defined by Ros," and this correlation also failed to yield satisfactory results. The fact that existing correlations failed to confirm the experimental data led to the need for development of a new correlation. Although a two-phase flow study was the primary objective of this investigation, data were also recorded for single-phase flow of water and gas, and constants were developed relating to pipe roughness and equivalent diameters for annular flow. These single-phase studies assisted materially in the development of certain of the two-phase flow results. Considerable previous work has been published which presented relationship of surface measurements to bottom-hole condition. The works of Buthod and Whiteley,6 Jones,' Poettmannb and the Texas Railroad Commission" are classic examples of the successful use of mathematical relationships which allow acceptable predictions of subsurface pressures, when gas is the flowing fluid. Darcy and others have derived relationships which may be used with minor modifications to predict subsurface flowing conditions in injection and water-supply wells. As previously stated, the application of the single-phase flow relationships

For the year ending February, 1916 PRESIDENT WILLIAM L. SAUNDERS,1 NEW YORK, N. Y. PAST PRESIDENTS CHARLES F. RAND,1. NEW YORK, N. Y. BENJAMIN B. THAYER,3 NEW YORK, N. Y. FIRST VICE-PRESIDENT PHILIP N. MOORE,1 ST. Louis, Mo. TREASURER GEORGE C. STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW, YORK, N. Y. SECRETARY BRADLEY STOUGHTON; NEW YORK, N. Y.

Jan 10, 1915

By L. V. Pirela, S. M. Farouq Ali

Some interest has been expressed recently in the application of solvents in conjunction with a thermal drive, such as a steamflood. At least one field project of this type has been reported. This paper makes the first attempt to provide some of the basic information necessary for choosing a solvent for such an application. Results of displacements conducted at elevated temperatures are also discussed. This paper shows that, in the case of alcohol-hydrocarbon-water or brine ternary systems, the system miscibility may increase, decrease, or both increase and decrease within the same system when the temperature increases. The distribution coefficient was consistently found to increase in favor of the oleic phase with an increase in temperature, which is advantageous from the standpoint of oil recovery. Results of solvent displacements in a sandstone core showed that even a relatively small temperature effect in the favorable direction (increase in miscibility and distribution coefficient) can lead to a 50 percent increase in oil recovery. On the other hand, if the system miscibility decreases with the temperature, even though the distribution coefficient increases, the oil recovery at the higher temperature may not increase. INTRODUCTION Miscible displacement has been the subject of many investigations. Miscible-phase solvent flooding, employing solvents such as alcohols that are miscible with both oil and water, has received considerable attention. Investigations conducted by Gatlin and Slobod,l Taber, Kamath and Reed,2 Holm and Csaszar,3 and Farouq Ali and Stah14 have helped in understanding the mechanism of solvent flooding. While the use of alcohols and similar solvents as oil recovery agents is economically unattractive, these solvents nevertheless provide a means of understanding the mechanistic aspects of important miscible-phase oil recovery processes such as the Maraflood process (discussed by Gogarty5). As shown by Taber et a1.,2 the phase behavior of a solvent-oil-water system is of .utmost importance in determining the efficiency of the oil displacement. This paper makes the first attempt to obtain the ternary phase behavior data for nine alcohol-hydrocarbon-water/brine systems at elevated temperatures. Results of core tests at elevated temperatures are also presented which corroborate the effect of temperature on oil recovery, as judged on the basis of phase-behavior data. The use of solvents at elevated temperatures has been suggested earlier by Farouq Ali.6 At least one field test of this type has been reportedO7 With the widespread use of thermal recovery techniques, it is possible in some situations (especially in steamflooding) that the use of a suitable solvent in conjunction with the heat carrier may be economically feasible. This paper attempts to provide some of the basic information needed for judging such feasibility. LOCATION OF THE PLAIT POINT The phase behavior of a typical ternary system consisting of a solvent, hydrocarbon and brine (or water) can be represented by a triangular diagram such as the one shown in Fig. 1 (for temperature TI). Point Pon the binodal curve represents the plait point, being the limit of tie lines such as Y1 Y2 The compositions of the coexisting oleic and aqueous phases are given by points Y2 and Y1, respectively, for any mixture composition along Y1Y2. The characteristics of ternary diagrams have been discussed by Findlay8 and others. Taber et aL3 have shown that the position of the plait point in a particular ternary system plays the decisive role in determining whether or not theoleic phase would be displaced in a continuous manner during an alcohol displacement. The area above the binodal curve also is important, since it represents

Jan 1, 1969

By G. T. Pruitt, T. L. Irby, P. B. Crawford, H. Ferrell

In water flooding peripheral, center-to-edge, line-drive or water-encroachment patterns the question has arisen, "when should a producing well be converted to a water-injection well?". It is realized that, if the producing well is shut in when water breakthrough occurs, some oil could be left in an unswept area. Yet, operation to high water-oil ratios may require processing much additional water. If a well is shut in, "where should the allowable be transferred?". A review of the literature indicates that very few data are available to the engineer to assist him in answering these questions. It is the purpose of this paper to present information which may be of value in selecting the flooding technique and the injection and producing wells and in scheduling injection and production rates. Certain phases of these problems can be studied in the laboratory. The Potentiometric model is well suited for studying many waterflooding problems. This model assumes that steady-state flow exists, that the mobility ratio is equal to one and that gravitational effects are neglected.'-' The three-phase sand model also has been recognized as an effective means for studying certain reservoir problems. Both models were used in making the study reported here. This paper discusses seven cases utilizing various waterflooding techniques. Data for the first five cases were obtained on the potentiometric model. Data for Cases VI and VII were obtained by constructing and flooding an unconsolidated sand pack (a three-fluid-phase system) and by determining the swept area and cumulative oil recovery for various types of operations. APPARATUS AND PROCEDURE The potentiometric model reservoir was 30 in. long X 10 in. wide by about 1/2 in. deep. Four wells were equally spaced in a line array along the lateral center line. (See Fig. 1.) Well No. 1 initially was an injection well for each of the patterns reported. The cases studied with the potentiometric model and sand model are described herein. The laboratory sand model reservoir was a 30- 10-in. rectangular Lucite vessel packed with sand to a depth of about 0.65 in. Four wells were equally spaced in a line array along the lateral center line. The reservoir material was an unconsolidated sand into which the reservoir fluids were mixed to yield fluid saturations of 55 per cent oil, 25 per cent water and 20 per cent gas. The water was added to the sand and the material mixed, after which the oil was added. Kerosene and water, the fluids used, gave a viscosity ratio of 1.64:1. In packing the reservoir, care was taken to assure constant fluid saturations and constant porosities. A new mixture was prepared for each run. During water flooding, a colored water was injected by a constant rate pump. The injection rate was 1.1 B/D/ft of sand thickness. For this series of tests, each of the producing wells was open to the atmosphere and, as in the potentiometric model study, Well No. 1 initially was an injection well for each of the patterns. KESULTS OF POTENTIOMETKIC MODEL STUDlES Two cases (Cases I and 11) involving equal pressure injections were studied, with the following results. Case Water injection was initiated at Well No. 1; the producing wells (Nos. 2, 3 and 4) were operated at constant and equal bottom-hole pressures. When water broke through at Well No. 2 and achieved the selected water-oil ratio, Well 2 was converted to a water injection well, resulting in two injection and two producing wells. The injection pressures at Wells 1 and 2 were maintained equal and constant; pressures at the producing wells were held equal, but they were lower than those at the injecting wells. A similar process was repeated when water broke through at Well No. 3. The flood was terminated when

By Will Mitchell, T. G. Kirkland, C. L. Sollenberger

BENEFICIATION of a Korean scheelite ore has been studied during the past year in the Basic Industries Laboratory at Allis-Chalmers Manufacturing Co. A flowsheet has been recommended including flotation, gravity separation, and a final cleaning by a magnetic separator. The investigation was continued in the field of flotation in order to establish the effect of certain variables on recovery and grade of rougher concentrates. The results of this investigation are recorded here. Mineralogy The scheelite ore was obtained from Korea and was mined from the Sang Dong deposit. This deposit is described as lying in gently dipping metamorphosed sedimentary beds of Cambrian age.' The metamorphism was probably either metasomatic replacement or recrystallization, or both, with subsequent hydrothermal deposition. Igneous bodies in the form of granite porphyry have been found within 7 km of the main shaft and are considered to be a possible source of the mineralizing solutions. The Myobong formation, the host for the Sang Dong deposit, was laid down in middle Cambrian times and consists of series of mudstone, siltstone, shale, and marl, with local stratification of mica schists, hornfels, and tactites. The scheelite is found in quartz bands in the tactites. Although there are six of these bands, only one, the "main bed" averaging 1.75 pct WOs, has been mined to any extent. The ore sample as received in the laboratory was the product of a cone crusher and was all —2 in. The rock appeared to be even textured, medium to fine grained, and gray green in color. No scheelite could be recognized by the unaided eye. However, under ultraviolet light of 2537 A, the scheelite fluoresced and could be distinguished from the gangue. Under the black light, the scheelite showed no definite vein structure but was disseminated throughout the specimen. The raw ore had a specific gravity of 2.96 and weighed about 125 lb per cu ft at —20-mesh Tyler. The —2-in. material was stage crushed through 20-mesh, and samples were cut for mineralogical, chemical, and spectrochemical analyses. Several polished sections were cut from hand specimens. Figs. 1 and 2 show quartz to be the matrix for scheelite. It was reported by Kim2 that the greatest scheelite concentration in the mine is found with a high concentration of quartz and a decrease in the abundance of garnet. Diameters of scheelite particles ranged from 1.2 mm down to less than 50 microns. Spectrochemical analysis showed the ore to be high in aluminum, bismuth, calcium, iron, magnesium, manganese, silicon, tungsten, and with lesser amounts of beryllium, chromium, lithium, sodium, and titanium. Chemical assays showed the —20-

Jan 1, 1952

By H. D. Kessler, M. Hansen, R. J. Van Thyne

The phase diagram of the titanium-rich portion of the system Ti-Cr-Fe to 70 pct Ti was established by means of isothermal sections at 900°, 800°, 750°, 700°, 650°, 600°, and 550°C, using arc-cast alloys. An isotherm at 800°C was determined for the section bounded by Ti, TiFe2, and TiCr2. Micrographic analysis was employed as the principal method of investigation, supplemented by X-ray diffraction and incipient melting studies. A ternary eutectoid, ß ? a+ TiCr2 + TiFe, occurs at approximately 8 wt pct Cr, 13 wt pct Fe, and about 540°C. AMONG the first titanium-base alloys in commercial production were the Ti-Cr-Fe alloys. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the system. No information on the constitution of the titanium-rich corner was available. Vogel and Wenderott studied titanium-poor ternary alloys.' As part of this program, the binary systems Ti-Cr and Ti-Fe have been determined previously by the authors.' Other investigators have also studied the binary systems Ti-Cr,3-7' Ti-Fe.³,8-10 Both of the binary systems are characterized by the eutectoid decomposition of the ß phase. Most of the effort of the present work has been concentrated on the titanium-rich corner with compositions of less than 30 pct total chromium and iron content. The determination of isothermal sections was the experimental approach used to obtain the ternary phase diagram. Vertical sections were used to check the consistency of the isothermal sections. While this investigation was in progress, a study of the Ti-Mo-Cr system at Armour Research Foundation disclosed the existence of a high temperature modification of TiCr2 above 1300 °C.11 This allotrope has a hexagonal structure of the MgZn2 type, iso-morphous with TiFe2, whereas the low temperature modification of TiCr2 is cubic," of the MgCu2 type. The existence of allotropy in TiCr2 of course means a more complicated set of phase relationships in this general region than if the phase were monomorphic, as was first assumed. Additional studies were made late in the investigation in order to clarify the part that the hexagonal TiCr2 phase plays in the ternary phase relationships. These will be discussed in a separate section. Because they are of greatest practical significance, the phase relationships in the titanium-rich corner will be presented first, omitting the equilibria involving the hexagonal modification of TiCr2 in an effort to simplify the presentation somewhat. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9 pct pure) produced by the New Jersey Zinc Co. High purity chromium and iron were obtained from the National Research Corp. Table I gives the analyses of these materials. Melting Practice: Over 100 alloy ingots weighing 10 to 20 g were melted in a nonconsumable electrode arc-melting furnace. As the techniques are identical to those reported previously,12,13 they will not be detailed here. The ingots were melted in the cavity of a copper melting block insert under a slight positive pressure of helium. No measurable hardness

Jan 1, 1954