Search Documents

The objectives of mining grade control are presented and examples of the techniques used in various open pit and underground mines are used to define the attributes of good grade control. Reasons are discussed for the success of various improved practices. The progressive development of grade control is presented and the balance between quantitative and qualitative data is analysed. The skills and resources required for grade control on mine sites that are using best practice are also presented. A number of problems in grade control have been solved recently however there are still issues that need to be addressed. Examination of the grade control process frequently stops after sample quality has been examined. There is much more beyond this that can now be optimised using conditional simulation models. Other future directions of mining grade control are also suggested. An extensive bibliography of published papers on grade control is included that will be maintained and updated on a website.

Jan 1, 2000

IN dealing with this subject the intention is not to write a detailed description of the various methods in vogue on the Kalgoorlie field, but rather to give a brief outline of three of the methods which are most universally in force, and from which, ultimately, a few comparisons may be drawn. The three methods which the writer proposes embodying in this article are known as "The Rill," "The Flatback," and "The Shrinkage." For comparative purposes each method will be applied to a block of ore 500 feet in length, and opened up by levels 200 feet apart."The Rin" System. It is necessary in this system, for facilitating mullocking, to make connections between levels by rising and winzing at about every 100 feet or 150 feet along the orebody. After the leading stope is beaten off for the full length ofthe drive, the level is timbered. Single stulls are put in up to a width of fourteen feet. If the span is too great for stulls, set timbers or saddleback stuUs are used. Stulls are lagged over with 4-in gimlet poles, and wooden chutes are built at intervals of 50-feet. Ore passes are cribbed up through the filling directly above each chute, and are constructed of 7-in. round timber or 9 in x 3 in square timber, the passes measuring 4 ft x 4 ft in the clear.Occasionally a double pass may be carried up, one side serving as a travelling way. Stoping is commenced off the winzes, and rills are gradually formed, one on either end of each winze. The rills are generally at an angle of 37° off the horizontal, this allowing for the boring...

Jan 1, 1909

By A G. L Pratt

Operational readiness is a commonly used term in mining and many other industry settings. However, translating this term into a coherent scope of work that is practical and meaningful is a challenge faced by many mining projects. This inhibits the allocation of resources to the work and its completion. The problem is with understanding how the terminology applies to establishing a mining operation. Resolving this problem requires clarity around what operational readiness means for a mining project’s transition to operations and who owns the tasks of completing operational readiness. The motivation for resolution of this problem is in appreciating the consequences arising from any lack of clarity in definition of this task, the timing of the work, and ownership for its completion. In broad terms, these consequences amount to an erosion of value at a critical time for both the new mine and the company and shareholders. This situation often arises where operational readiness is not adequately addressed in project’s study phases. As a result, neither time, resources nor money are adequately provided to complete the work required. In other cases, operational readiness is sometimes assimilated with the delivery of the project’s physical assets by the project’s construction team, rather than aligned with the establishment of the operating team to deliver the desired operational outputs. This paper argues that operational readiness starts in a project’s study phases and flows through into the start of operations. The definition of operational readiness is discussed as a task, and a model for its planning and completion is presented. This discussion includes assigning ownership for operational readiness planning and delivery to the General Manager of a new operation and the operations leadership team, who are central to the success of this work. After all, the reputations of this leadership team depend on the performance of the operation in its first few years. The author’s work over the last 20 years, leading operational readiness programs and the preparation of feasibility studies for mining projects, has provided the insights and evolution of ideas that are central to this paper. Operational readiness is fundamentally directed at ensuring a new mining operation gets away to a successful start and builds a solid foundation for the future of the mine/operation/province. It requires clarity of purpose, ownership and coordination by people in the operating team, and their preparation of the requisite process definition and establishment of the significant relationships required for operations. Without its successful completion, it is unlikely the new operation will meet and sustain its start-up targets. This paper discusses a practical approach to operational readiness for mining projects.

Mar 29, 2023

When xanthates or dithiophosphates are used as collectors in sulphide ore flotation, adsorbed species may be identified by gas chromatography of the volatile products formed during low temperature pyrolysis. For collector additions ,as low as 20 g/tonne of ore, pyrolysis of the flotation products usually gives' an olefin directly related to the particular xanthate or Aerofloat reagent used. The method is able to provide valuable qualitative and quantitative data relating to the extent of collector adsorption and the resulting changes in the hydrophilic or hydrophobic nature of the mineral surface.

Jan 1, 1974

By Klenowski G, Gilmour G. A

The Metropolitan Water Supply, Sewerage and Drainage Board, Perth, has recently con- structed two major sewerage tunnels in the metropolitan area and a further one is under construction. These tunnels were constructed in sand, sandstone and limestone. The Tamala Limestone is a Pleistocene calcareous dune sand which now varies in com position from loose sand to cemented rock. Investigation techniques included surface mapping, auger and diamond core drilling, seismic refraction geophysics and mechanical testing. The variable nature of the ground caused difficulties in all aspects of the investigation, particularly in core recovery and seismic work. The Beenyup Tunnel, 2.25m in diameter and 3440m long was excavated with a Dosco TBM 1800 machine and shield with precast concrete Charcon Universal bolted segment lining. The Burns Beach Sewer Tunnel, 1.27m in diameter and 860m long was hand excavated with precast reinforced concrete lining pipes jacked continuously behind an excavation

Jan 1, 1981

By G Hancock, A Kemp, I Taylor

The mine site is situated south east of Port Hedland in the Pilbara region of Western Australia. A detailed engineering design was undertaken for six irregularly shaped waste rock dumps at the site. The design was undertaken to ensure long-term stability of the dumps and optimise material movements for closure construction. The Watershed Erosion Prediction Program (WEPP) and SIBERIA landscape evolution modelling was undertaken for the landforms using regional and site-specific material characteristics to provide an indication of the maximum allowable slopes and corresponding slope lengths for long-term stability.The majority of the waste materials present in the waste rock dumps are considered likely to be subgrade banded iron formation (BIF) and chert, which is generally competent material. The presence of a large number of dolerite dyke swarms indicates appreciable volumes of dolerite were produced as waste from the pits. Geological records also indicate that the dolerite is logged as being heavily kaolinised in the geological logging, hence kaolinite is very likely to be present within the waste dumps on-site. This material has an elevated risk of being highly erodible/dispersive. Clays and shales are also likely to be present in the dumps and are considered to be less competent material (relative to the BIF/chert).The final design configuration of the largest existing ‘unplanned’ waste rock stockpile is compared to a hypothetical continuous ten degree outer embankment alternative. This paper will present a brief description of the alternatives for closure of three waste dumps in close proximity to each other and how the detailed design based on site-specific materials and conditions compare to an alternative approach blankly assuming that most materials will be erosionally stable at less than ten degrees.CITATION:Kemp, A, Taylor, I?and Hancock,?G,?2014. Landform design for Pilbara mine site – why plan and design waste rock dumps for closure based on site-specific conditions?, in Proceedings Life-of-Mine 2014 , pp 47–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D Crequer

Land rehabilitation at Golden Cross is reviewed, 8 years after mine closure in 1997/98, from the perspectives of a Peer Reviewer (land rehabilitation) and a Regional Council Officer (Resource Consents compliance). Land rehabilitation items we discuss include: management of restored pastures, native plantings (on-site riparian and block plantings and off-site environmental riparian enhancement plantings), wetlands (on-site tailings lake and sediment ponds littoral zone plantings, and basement of the open pit; and off-site wetlands enhancement plantings), pine plantations on-site and on surrounding land, stabilization of the Tailings Lake Embankment (landslide) and Open Pit capping, capping of acid-mine-rock, stability of discharge channels, buildings and amenities, public access for recreation, educational uses, and future management of the site. Pest control has helped to conserve the rare and endangered HochstetterÆs (Leiopelma hochstetteri) and ArcheyÆs (L. archeyi) frogs, and a regionally significant stand of rare swamp maire (Syzygium maire) has been conserved and fenced.

Jan 1, 2006

Throughout history, many of the world's achievements, conflicts and problems can be traced to the demand for minerals. With the rapid expansion of our industrialised society in recent years the demand for minerals has grown to such an extent that uncertainties about availability and cost have arisen, especially in the case of energy minerals.Minerals have acquired a new dimension for governments as the availability of these resources is interwoven with the ability of governments to achieve their developmental goals on national and international levels. Accordingly, the supply of minerals will increasingly be affected by social and political factors.

Jan 1, 1986

By J L. Mauk

Gladstone Hill, a volcanic-hosted low-sulfidation epithermal prospect in the Coromandel Peninsula, is less than 1 km from the world-class Martha Hill Au-Ag deposit. Gold-silver-bearing quartz veins occur in Late Miocene andesitic volcanic rocks of the Waipupu Formation that are extensively altered. The occurrence, spatial distribution and temporal relationships of hydrothermal minerals have been determined along two cross sections that transect the Amaranth, Gladstone, Cowshed and Moonlight veins. Quartz and pyrite are ubiquitous along these sections. Adularia and chlorite are widespread, but both are scarce in wall rocks adjacent to the Moonlight and Cowshed veins. By contrast, rare hydrothermal albite and epidote are restricted to wall rocks surrounding the Amaranth vein. Illite, which replaces adularia, is widespread and grades laterally eastwards into a zone of interstratified illite-smectite that envelops the Moonlight and Cowshed veins. During late-stage hydrothermal activity, rare calcite formed at depth and uncommon kaolinite and alunite formed at shallow levels. The overall clay mineral zonation with illite grading eastward into interstratified illite-smectite reflects paleothermal gradients of >220¦C to -170¦C towards the margin. The alteration assemblage of quartz, adularia, chlorite, albite, epidote, illite, interstratified illite-smectite and pyrite reflects formation from a near-neutral to weakly alkaline pH chloride water that contained low concentrations of CO2, Late calcite formed from very local descending steam-heated CO2rich water, whereas the rare assemblage of kaolinite and alunite formed from shallow steam-heated acid-sulfate water. Analysis of the available data indicates that the Martha Hill deposit and the Gladstone Hill area formed within a single large geothermal system. We infer that the Martha Hill deposit formed in the main upflow zone, whereas the Gladstone Hill area may have formed adjacent to this upflow zone.

Jan 1, 2001

By J Westh, S Rashleigh, L Gallagher

Mining companies are moving towards automated haul trucks and other equipment. One reason for this is that if automated trucks can operate in a standard pattern over and over again without variation, then human error is reduced, if not eliminated.The challenge for mining production leaders/managers is to ensure operators follow standard operating procedures for load and dump operations, with each operator doing the same thing, every time. However, operators are only human and inconsistent performance is rife at every mine site. The finger may be pointed at the operators for not doing as instructed. The clarity and variability of trainer instructions may be considered causal to the problem. Herein lies the problem. Almost all operators believe they are following the procedure very closely; moreover, they all demonstrate a strong desire to conform to instruction.Using video analysis and feedback, each operator can be shown where and by how much they differ from the benchmark set by their company. Operators, often for the first time, can see definitively what they are doing, compared to industry best practice.The technology utilised by real-time video (RTV) crews measures time, distance and angles. It can overlay the video of the operator at the load site, with video of the perfect pass. Operators are amazed when they see how near to, or how far they are from best practice.The footage and data gathered by RTV assists operators in understanding exactly what adjustments are required to increase proficiency. It also assists load and dump superintendents to identify where in the process they are losing time. When translated to overburden removal or mineral/resource extraction, the result is large production economies without the need for large capital investment in new automated technology.CITATION:Westh, J, Gallagher, L and Rashleigh, S, 2012. Improving safety and mine productivity using real-time video technology, in Proceedings International Mine Management 2012, pp 173-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By G S. Esterhuizen, M M. Murphy, T S. Bajpayee

The strength reduction method (SRM) has been implemented in the FLAC3D finite difference software and applied to coalmine entry support evaluations. The FLAC3D numerical models have been calibrated against instrumented field sites in varying geologies, depths and field stress conditions. The calibration between the field and model results obtained a satisfactory match for rock deformation and support response. Previous research has also developed good correlations between numerical model stability estimations using the SRM and empirically derived stability estimations using the analysis of roof bolt systems (ARBS) software and the coalmine roof rating (CMRR). The purpose of this paper is to further apply the SRM to investigate how specific geotechnical and support parameters can impact coalmine entry stability. Results from different studies demonstrate how the calibrated models were used to investigate a few of the well-known questions in both mine design and support design. For mine design the impact of strong and weak beds in the roof strata, rotating the principal stresses and weakening the floor on excavation stability is investigated. For support design the impact of support length, support spacing and adding cable bolts to the design is demonstrated. These scenarios are evaluated in developmental coalmine entries for a variety of geology and field stress conditions. Stability factors are calculated for each scenario using the SRM. The SRM allows the impact of each parameter to be quantified and allows the support system to be optimised for given geotechnical conditions.CITATION:Esterhuizen, G S, Murphy, M M and Bajpayee, T S, 2014. Analysis of geotechnical and support parameters on coalmine entry stability using the strength reduction method, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 383–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

In the early stages of opening up a mine, when there is some uncertainty as to its future career, necessitating caution in laying out works of a permanent character, the want is often felt of an assay furnace, easily built and easy of transportation, should the" mine " prove to be " no mine." Again, cases occur in which parties buy the right to treat comparatively small heaps of tailings, and then shift their plant to other localities. Under these circumstances it is necessary to restrict the plant to the barest necessaries, to suit, so to speak, the nomadic character of the work.An assay furnace that is really portable, easily transported, erected, taken down, of little weight, always ready for action on short notice, is indeed in these cases a desideratum which has long been wished for. The gasoline furnaces introduced intothe Australian market some time since practically fulfil these conditions; but they have the fatal drawback of being dependent on a constant supply of the liquid fuel, gasoline, which is seldom, if ever, obtainable locally in' any wayback mining township...

Jan 1, 1904

The limit of pressure to which an underground dam may with safety be subjected, is a question that-as far as the writer knows has not received the same attention from authorities on engineering construction, or practical mining, that has been accorded to questions on which the design and strength of other structures or machines in connection with a mine are based. That dams may, under certain conditions, be constructed to resist water under great pressure is a known fact. But the difficulty of demonstrating beforehand that any proposed structure of this kind will withstand the pressure and be effective is, owing to the indeterminate nature of some of the risks to be provided against, very great. In the present state of our knowledge it may almost be laid down as a rule, that a dam of this kind should not be undertaken where grave consequences would attend failure until experience of structures where the physical conditions are similar, but where there are no such risks, has given assurance that such work would stand.In Mines and Minerals for May, 1900, there is published a paper by Mr. James McNaughton describing the construction of three underground dams in the iron mining district of Michigan.The first of these was put in to hold back a flow of 750 gallons per minute, which when pent up created a pressure of 276 pounds per square inch, showing that the height of the sustained column was about 635 ·feet. The hole through which the water issued was in the bottom of the cross cut it was enlarged by removing all loose rock for a depth of 18 ft...

Jan 1, 1901

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2007

By G Burton, S Fityus, J Li, S Vaughan, D Payne

Daunia and Caval Ridge coal mines, owned and operated by BHP, have been co-disposing rejects and dewatered tailings within spoil dumps from the beginning of their operations in 2013 and 2014, with the purpose of minimising environmental impact and geotechnical risk. Following the recent large failures of tailings dams around the world, BHP Coal, through its Coal Tailings Program, plans to transition other coal mines to deliver “dry” tailings and produce mixed plant rejects (MPR) for inpit co-disposal. This will materially reduce future tailings dam risk exposure. Previous laboratory shear strength testing was conducted on rejects with a maximum particles size of 20 mm, and some concerns were raised that this might not represent the mechanical properties of the actual full particle size distribution (PSD) rejects. BHP was also aware that using different technologies to dewater the tailings, such as belt press filters (BPF) and solid bowl centrifuge (SBC), could produce thickened tailings which could significantly modify the physical behaviours of the MPRs, particularly the bonding between particles. Therefore, laboratory testing on both coarse rejects and mixtures of the coarse rejects and dewatered tailings (MPRs), with full PSDs, was carried out. Testing was performed using the large direct shear machine developed by the Australian Coal Association Research Program (ACARP) project C20019 in 2017, as well as a 300 mm diameter triaxial apparatus at the University of Newcastle (UoN). This paper presents details of the laboratory testing program and results for the rejects from the first studied mine of the BHP Coal Tailings Program. It compares the shear strengths measured at full scale with those tested on modified (scalped or crushed) specimens in the past; and discusses the tailings dewatering technique selection from geotechnical aspects based on the testing results, and finally presents some dump and tip head stability analysis results using the testing results.

Jul 1, 2021

By L P. Trout, D G. Reid

PanAust Limited (PanAust) has successfully constructed and commissioned two mining operations in Lao PDR over the past decade and undertaken major studies for three new mine developments. The management of potentially acid generating mine waste and tailings in close proximity of local communities sensitive to water discharge quality have been recurring themes that have confronted PanAust’s project study, development and operational teams. Further compounding challenges, such as the effects of intense annual tropical monsoonal conditions, staging of embankment raises and regular lifting of spillway structures, integrating mine waste and tailings management into production plans and ensuring the long term stability of structures, have been addressed by implementing leading practice management solutions.A recognition of the criticality of managing the substantial business risks associated with these crucial activities led to the early establishment of a governance structure to ensure that the highest standards are embraced for planning and execution. Importantly, these are guided and monitored by a panel of highly experienced and qualified international specialists reporting directly to PanAust’s Managing Director – the Tailings Independent Review Panel. The stewardship process has been effective in identifying potential shortcomings in management systems and has led to enhanced executive commitment to risk informed designs, assurance and overall process rigour.CITATION:Trout, L P and Reid, D G, 2018. PanAust Limited’s approach to mine waste and tailings stewardship, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 135–155 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

A massive cobalt-containing pyrite orebody occurs in banded albite-quartz-biotite rocks at Thackaringa, some 30 km SW of Broken Hill. Because of the world-wide shortage of cobalt during the late 1970s, serious consideration was given to the development of a suitable flow-sheet to recover the cobalt from this ore. Details of a pressure leaching process in which more than 90 per cent of the cobalt is extracted from a pyrite concentrate are presented.

Jan 1, 1983

The Nena high sulphidation-type copper-gold deposit is composed of andesitic pyroclastic units with minor interstratified lava flows. Epiclastic sandstone and conglomerate, and siliciclastic rocks consisting of mudstone, shale, lithic and bioclastic sandstone and conglomerate are locally present. Pre-mineral diorite intruded and domed the volcano-siliciclastic sequence. Economic copper-gold is hosted by vuggy quartz altered lapilli tuff and tuff breccia. The early hydrothermal alteration stage involved deposition of epithermal banded quartz and chalcedonic silica in localised environments. This alteration stage was locally superimposed by a hydrothermal breccia event. Following the breccia event, magmatically-derived volatiles were channelled through a NW striking dilational fault zone and generated the high sulphidation alteration. The high sulphidation alteration is zoned from a vuggy quartz core with local massive replacement silica through a broad pyritic quartz-alunite halo and finally to a thin illite-smectite zone. This is surrounded by regional chlorite-epidote-smectite alteration. A gangue mineral phase consisting of quartz, alunite and baryte overprinted the zoned high sulphidation alteration and preceded the main copper-gold-arsenic mineralisation. Early sulphide deposition is characterised by marcasite, arsenical pyrite and melnicovenite. Main-stage copper-gold mineralisation involved sequential deposition of hypogene bladed covellite+chalcocite, enargite-luzonite and luzonite+stibioluzonite respectively. The copper sulphides are zoned from bladed covellite-chalcocite in the north (cross-sections 5000 - 5600 N) through enargite-luzonite (cross-sections 4700 - 5000 N) and to luzonite????stibioluzonite in the south (cross-sections 4400 - 4700 N). A late phase of minor acicular covellite and enargite+luzonite overprinted the zoned copper sulphides and associated gold mineralisation. Gold mineralisation commenced at the transition from enargite to luzonite, and continued through the deposition of luzonite-stibioluzonite in both stages. Most gold was deposited during the main-stage mineralisation. Yellow native sulphur was deposited in the remaining vugs and defines the waning stage of the hydrothermal system. Post-mineral dioritic intrusives and feldspar porphyries intruded the volcano-siliciclastic sequence. Finally, supergene chemical processes with associated erosion and uplift generated a 40 - 50 m thick oxide-hosted gold cap. The oxide gold cap is underlain by a 35 - 45 m thick blanket of supergene chalcocite+covellite mineralisation which overlies and occurs throughout the main hypogene copper-gold zone. Supergene gold is related to the distribution of primary gold-bearing sulphides. Therefore, remobilisation and redeposition of gold are considered to be insignificant and very localised.

Jan 1, 1999

By A H. Clemens, T A. Moore

This paper discusses a number of technical issues related to marketing coal. It outlines how the results of research undertaken in New Zealand and overseas can help producers address a range of technical factors that impact on production costs and marketability. The paper also discusses trends in coal utilisation for power generation and how new technologies may require coal with different characteristics. Research and development into options for CO2 sequestration are discussed including carbon storage in forests, and removal of CO2 from flue or fuel gas in power stations, and its disposal.

Jan 1, 1997

By S T. L Harrison, J-P Franzidis, M Becker, N Dyantyi, J L. Broadhurst

Gold mining is a major contributor to the South African economy, but is associated with several environmental issues such as acid rock drainage (ARD). ARD is due to the oxidation of sulfides in gold tailings and is characterised by low pH, high sulfate content and elevated concentrations of heavy metals that contaminates scarce water resources and subsequently limits the use of such waters without treatment. Treatment strategies can only be implemented if the acid-generating potential of mine wastes is effectively predicted using common static and kinetic acid prediction tests. The choice of test performed is usually a trade-off between the number of samples, speed of the test, cost of the analysis and level of information obtained. Often the results of these various tests are not consistent with one another. This study uses mineralogy to analyse biokinetic test results of a Witwatersrand gold sample in order to improve the understanding of behaviour of mine wastes under different ARD prediction test conditions.All ARD prediction testing methods investigated in this study showed that the gold sample is considered to be potentially acid forming with net acid generation (NAG) pH of 2.5 and net acid producing potential (NAPP) of 36 kg H2SO4/t. Results of biokinetic test showed that ANC was consumed within four days confirming acid producing potential of the sample with low neutralising potential as observed from acid base accounting (ABA) (4.7 kg H2SO4/t) and mineralogy (4.9 kg H2SO4/t). Results generated in this study demonstrated importance of mineralogy in both understanding the controlling reaction mechanisms playing key role in ARD formation and its capability as a prediction technique. Future work will focus on the application of mineralogy in interpreting the behaviour of mine waste under different static test conditions with a view to assessing their applicability and reliability in estimating potential acid generating characteristics of gold tailings.CITATION:Dyantyi, N, Becker, M, Broadhurst, J L, Harrison, S T L and Franzidis, J-P, 2013. Use of mineralogy to interpret laboratory-scale acid rock drainage prediction tests - a gold case study, in Proceedings World Gold 2013, pp 519-526 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013