Search Documents

By Lyman G. J

Dense medium drum separator efficiency was analysed at two Western Australian iron ore concentrators. Efficiency data had hitherto been difficult to accumulate due to the high cost of analysing representative, and therefore large, coarse ore samples. To overcome this problem, recoverable density tracers, which are in effect artificial mineral and gangue, were manufactured in three different sizes (15 mm, 30 mm and 60 mm). Their use enabled partition curves to be studied within one hour of conducting a test: separation densities were generally lower than the feed medium density for all three sizes of density tracer. For a given set of operating conditions, the smaller tracers had lower separation densities and larger ecart probab/es than the large tracers. These phenomena are explained with the aid of a conceptual model of a drum separator, which assumes that the feed ore plunges to the bottom of the drum upon introduction. Particle rising velocities are, therefore, process determining.Medium rheology was altered by adjusting the proportion of solids in the pulp. This was accomplished by changing both the pulp density and ferrosilicon/magnetite ratio. Higher solids volume fractions invariably caused a decrease in separation densities and an increase in ecart probables, most markedly for the smaller tracers. A similar response was observed when feed tonnages were raised.An explanation for these phenomena is sought in the discussion which also suggests means of improving drum separator efficiency.

Jan 1, 1987

In the last two years the Commission for the Environment has received four Environmental Impact Reports (EIR) for Audit and has been or is involved with at least four environmental impact assessments (EIA) related to mining. The EIRs have included Weavers Coal Mine, the Monowai-Maratoto mining proposal, the Martha Hill mine and the Wainui Road Mill. The EIAs are related mainly to coal fields in the Waikato but also included a further EIA on Martha Hill.

Jan 1, 1986

By H Kurth, L Balzan

The potential for bulk diversion was identified and quickly implemented following the development of bulk sensing technologies applied to conveyed flows. In the early 1980s real time analysis of ash in coal was intended to improve the understanding and control of quality variability. By the end of the 1980s approximately 5% of coal analysers installed were being utilised for bulk sorting; diverting flows to create stockpiles to improve blending flexibility and boiler feed consistency, diverting waste material, or bypassing the beneficiation process when the coal met product quality criteria. In the 1990s bulk sensing and sorting utilising natural gamma detection was applied to conveyed waste in gold-uranium mineralisation and allowed ore to be recovered and processed that would otherwise have been discarded. Further applications developed in the iron ore sector where product quality ore could be diverted to bypass beneficiation and save significant unnecessary processing costs and improve recovery by avoiding process inefficiency losses. Plant capacity was freed up to be utilised by material that required processing. Similar benefits became evident in the phosphate industry and in base metals where multi-elemental analysis using Prompt Gamma Neutron Activation Analysis provides ideal opportunities to representatively measure 30 second conveyed increments at high accuracies. This has been successfully adopted in copper, nickel, platinum and lead-zinc to improve waste removal after primary crushing to eliminate unnecessary expense and improve plant efficiency. The benefits include increased output from existing operating capacity, significant reductions in consumable costs and generation of fewer detrimental waste streams. The paper outlines the technologies and discusses case studies covering the above commodities, demonstrating the immense value that representative real time measurement of conveyed flows can create. Measurement data concurrently provides multiple benefits in operational performance besides sorting, through ore reconciliation, ore blending, feedforward control and metal accounting, adding further value.

Nov 10, 2020

By D M. Marques, J F. C L Costa

The estimation of process plant head grade is not trivial and is a source of constant dispute within the mining industry. Grade estimates informed by the short term mine planning are frequently not reproduced by sampling the continuous flow of ore at the plant. Head grades are normally obtained by periodically sampling the continuous flow during a day or shift, and taking the average of the multiple increments collected. The standard error of this mean grade depends on the ore variability and the frequency (number) of aliquots extracted. The more increments are taken the higher is the precision on the calculated mean. Variographic experiments are normally used to map grade variability along a certain period of time and the extension variance is derived from this variogram. This experiment is time consuming, expensive and cumbersome. Mining industry personnel rarely apply this approach. Additionally, a temporal variogram can vary from day to day as different ores are mined along the life of the mine. This paper investigates a novel approach based on simulating the grades feeding the processing plant. In situ 3D grade models are built using geostatistical simulations. Grade spatial continuity and variability are reproduced in models that mimic the real deposit. These models are used in mine planning and scheduling transforming a 3D block model into an one dimensional string of values feeding the plant (one dimension flow). These grades have the statistical characteristics of the unknown real grades and can be sampled to emulate a variographic experiment. The results showed consistency and adequacy to estimate the sampling error (Gy, 1998 p 31) for various sampling intervals using the simulated grades. Also the results show a variographic experiment can change significantly from time to time, as ore changes and a selected sampling protocol can become obsolete if not adjusted for ore variability.CITATION:Costa, J F C L and Marques, D M, 2012. Defining a sampling strategy for a continuous flow supported by geostatistical simulations, in Proceedings Sampling 2012 , pp 3-8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By P Vaikkattil, K Li, J Bullock

Unlocking maximum value is essential when designing a stope and the associated drill and blast packets. This is becoming increasingly important at Olympic Dam as the operation continues to expand south into the new mining areas away from existing infrastructure, increasing operating costs and required capital investment; into areas with less competent ground conditions, requiring smaller stopes and increased interactions. The introduction of Orica’s WebGenTM system is one way in which Olympic Dam can continue to unlock value into the future by decoupling traditional drill and blast limitations. The Lime 390 stope was the first stope at Olympic Dam to trial the new technology on the last blast packet. This paper reviews the drill and blast design of the Lime 390 stope, including the technical and operational challenges associated with the stope and the trial of the Orica’s WebGenTM system for the firing of the last blast packet.

Mar 15, 2021

By R J. Goldfarb

Reduced intrusion-related gold deposits have become a new, low-grade, large-tonnage exploration target during the last decade. The best recognized examples of such deposits are recognized throughout the Tintina Gold Province of the northern North American Cordillera. Because such examples may have many features in common with orogenic gold deposits, such as anomalous Bi, W and Te, low salinity and CO2-rich ore fluids, and a spatial/temporal association with igneous rocks, confusion and controversy have now become commonplace in classification of many gold deposits formed along convergent margins. The best discriminators of IRGS are likely to be their: +        regional location in deformed shelf sequences on the inboard side of a series of accreted terranes and within terranes that also contain important tin and (or) tungsten deposits; +        local spatial association of gold ores with cupolas and contact aureoles of relatively reduced, alkaline-leaning, and volatile-rich plutons; +        post-deformational timing of gold deposition; +        extremely low sulfide content (commonly <1 vol %) of ores within igneous bodies and the outward zoning, through proximal skarns and to distal base metal-rich veins, from the causative pluton; and +        low grades (<1 g/t Au) of auriferous sheeted vein systems in pluton cupolas.

Jan 1, 2005

By Baker G

The detailed mineral composition of the lead-zinc ores at Captain's Flat was first studied in 1942 (Edwards, 1943).At that time the workings did not extend far below the 750ft. level. Since then development has been extended to the 1,390ft. level, and -at the request of the management of Lake George Mines Ltd., an examination of the ore from the deeper levels has been made as part of the research programme of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organization.This account is. based on that examination (Mineragraphic Rept. No. ,537, C.S.I.R.O.)GENERAL GEOLOGYThe geology of the Lake George Mines has been described briefly in The Geology of Australian Ore Deposits (1953), and in much greater detail in an unpublished report by K. Glasson (1952). The area consists of fossiliferous Upper Ordovician sediments overlain by volcanics (Kohinoor VoJcanics), and by fossiliferous Silurian sediments. The volcanies comprise a series of· flows ranging in' composition from dacite to rhyolite, with interbedded tuft's and shale lenses.The region has been strongly folded. The regional strike is from 340° to 355°, and dips are from 75°W. to 75°E, A major syncline, pitching 200 N., occupies the centre of the area. The Kohinoor Volcanic'l outcrop as two bands which represent the east and west limbs of this syncline.The Volcanks in the western limb, with whIch the orebodies are associated, are more strongly sheared than those in the eastern limb.

Jan 1, 1953

By C Antonio, R Narayan, A Scheuermann, S Quintero, M Edraki, M Ziemski

Tailings are mostly loose material and can be classed as non-plastic sandy silts. They also tend to have low permeability, resulting in slow consolidation (settling) rates and low shear strength, even after consolidation. These qualities make them prone to liquefaction and, therefore, physical instability. In contrast, coarse waste rocks possess high shear strength and permeability when stacked in dumps. However, air and water flow-through the voids can cause acid mine drainage (AMD) with significant undesirable environmental implications. Combining the two waste streams before disposal by mixing presents a potential opportunity to harness the desirable properties of both waste streams. This practice is termed co-mingling and is prevalent within the coal processing industry. Co-mingling of metalliferous mine tailings is, however, a relatively new concept. By combining the coarse waste rocks and fine-grained tailings streams, the fine tailings tend to fill the voids between the waste rocks, reducing hydraulic conductivity and advective air (oxygen) flow into the rocks, thus possibly reducing acid mine drainage (AMD). Conversely, tailings are introduced to large frictional particles from waste rocks, providing reinforcement, stability, and possibly improved drainage. New separation methods are being introduced to the mining sector, which have the capacity to extract waste with significantly larger particle sizes. High Voltage Pulse (HVP) is a technology in which relatively coarse particles ranging in size from 30 to 100 mm are exposed to an electric pulse discharge. This pulse preferentially fractures mineralised particles while leaving unmineralised rock (gangue) intact. The stream can then be passed via a screen, with smaller mineralised particles reporting to the undersize and removing coarser unbroken barren particles, thereby eliminating waste. Coarse particle flotation (CPF) is another emerging new technology in metalliferous mining that applies flotation separation to coarser particles than conventional flotation. These new technologies produce different tailings (waste) streams with varying physical characteristics and possibly surface chemistries. This research aims to test new tailings mixtures by applying the co-mingling concept to blend the reject streams generated by these two technologies (HVP and CPF) with the tailings produced by conventional flotation. Combining different waste streams before disposal can improve stability and potentially reduce the acid mine drainage (AMD) rate, thus enabling early access to the tailings storage facility for rehabilitation and closure.

Aug 2, 2023

By M Frenzel

At the last MassMin Conference in Sudbury, Caterpillar’s vision of a continuous mining concept for block caving operations was presented on the background of global raw material demand and its continuous increase. By analysing today’s structure of mining processes in block caving, the paper (Krings, Steinberg and Frenzel, 2012) highlighted the main bottlenecks in the process chain and identified conceptual solutions by help of a case study. The main focus was the paradigm shift from discontinuous batch type operation to a continuous mining process of the blocks.In 2016, the strategic vision has taken major strides forwards and remote continuous operation has become a reality. Caterpillar’s continuous operation system – the Rock Flow system – was successfully installed in Codelco’s Andina mine and start of operation is scheduled in the first half of 2016.Based on continuous product developments, this paper sets the focus on two main aspects of continuous mining. First, field experiences of the Rock Flow system will be shared, highlighting the Andina project course from system installation, to commissioning and successful system start. The second aspect concentrates on the system and mine layout as discussed in the case study scenario in MassMin 2012 (Krings, Steinberg and Frenzel, 2012).Based on Caterpillar`s continuous product development, the Rock Flow system set-up and panel design were modified for a general roadway design and drawpoint layout. The new design allows an optimised use in block preparation phase (spreading) and full production phase (reaping), operating a fleet of load-haul-dumps (LHDs) and Rock Flow systems. The combined use of the two technologies optimises the mining process in every stage of block life and significantly increases the performance of the continuous block caving operation in the production panel to pave the road for the next generation of super caves.CITATION:Frenzel, M, 2016. New continuous production system in block cave mining – the rock flow system, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 543–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By V P. Beskrovnaya

Tests for the development of a metals recovery technology from samples of a Russian gold-bismuth deposit were carried out. Gold, silver and bismuth assay reported 5.6 g/t, 3.0 g/t and 0.08 per cent, respectively. Two flow sheet options were pilot plant tested: gravity/cyanidation of gravity tailings with subsequent flotation of cyanidation/carbon-in-pulp (CIP) tailings, and gravity/flotation concentration with cyanidation/CIP of concentrates. Option 1 results showed lower gold, silver and bismuth recoveries (81.3 per cent Au, 55 per cent Ag and 74.0 per cent Bi) due to low flotation efficiency for cyanidation tailings. Therefore, a flow sheet involving gravity/flotation concentration to produce bismuth-gold concentrates (0.8 per cent Bi) with subsequent cyanidation/CIP was recommended. Gold, silver and bismuth recoveries obtained by this method to the combined gravity/flotation concentrate were 90.2 per cent Au, 83.3 per cent Ag and 80.2 per cent Bi of the ore, respectively. Overall gold, silver and bismuth recoveries were 83.0 per cent Au, 40.5 per cent Ag and 80.2 per cent Bi, respectively. Gold and silver recoveries to the cathode precipitate were 92 per cent Au and 48.6 per cent Ag (per operation). Reagents consumed for flotation were 0.1 kg lead acetate/t ore, 0.4 kg butyl xanthate/t ore, 0.2 kg T-80 frother/t ore, 0.02 kg sodium hexametaphosphate/t ore, 0.15 kg copper sulfate/t ore. Reagents consumption for cyanidation was 0.42 - 0.48 kg NaCN/t ore and 0.2 kg CaO/t ore. It was recommended to deliver bismuth concentrates after hydrometallurgical treatment to a smelter. Overall bismuth recovery including bismuth recovery achieved by pyrometallurgy was 60.0 per cent. However, it was obvious that delivery of bismuth concentrates to a smelter and their commercial treatment would be very expensive due to relatively high mass pull of bismuth concentrates (7.6 per cent of the ore weight). For this reason, thiourea leaching and hydrochloric acid leaching with subsequent cyanidation/CIP were investigated as alternatives to cyanide leaching. These two alternatives were proposed to enable optimal recovery of valuable metals from concentrates on-site. Recoveries obtained by thiourea leaching were 91.2 per cent Au, 90.5 - 91.9 per cent Bi and 77.0 - 78.1 per cent Ag. However, that method required considerable capital and operating costs. As an alternative, hydrochloric acid leaching with subsequent cyanidation was investigated. Test results showed improved gold, bismuth and silver recoveries, which were 94 - 95.9 Au per cent, 94 - 96 Bi per cent and 76 - 78 Ag per cent, respectively. Hydrochloric acid consumption was 100 kg/t concentrate or 7.6 kg/t ore. Current efficiency during electrowinning was about eight to 12 per cent. A recommended flow sheet involving hydrochloric acid leaching of concentrates, electrowinning of bismuth from solutions, recycling solutions after electrowinning and cyanidation of hydrochloric acid leaching cakes is described. Overall recoveries achieved by the proposed flow sheet were as follows: 84.8 - 86.5 Au per cent, 75.8 - 76.9 Bi per cent and 63.2 - 64.9 Ag per cent. Based on results from these tests, initial data for a bankable feasibility study and plant designing were developed.

Jan 1, 2007

My speech this morning is not a technical one, rather I will aim to tell you about the New Zealand Aluminium Smelters Limited and how I see it fitting into the Western World aluminium scene.

Jan 1, 1983

By H Aral

A rotating magnetic field can be produced in a magnetic separator by using a magnet rotor fitted with alternate north-south magnetic poles, similar to the rotors currently used in modern eddy current separators. Rotation of the magnetic field causes ferromagnetic particles to rotate during magnetic separation. The particle rotation can then be used simply to remove entrapment during a conventional attraction magnetic separation (RMF lift separation), or it can be used to roll particles away from non-rotating particles, and to move them out of the separator under their own rotation (RMF rotation separation). RMF (rotating magnetic field) separation is a separation for ferromagnetic particles. These particles have a very ordered magnetism that is locked into directions of easy magnetisation in the crystal. As a result, if the external field rotates, the particles attempt to rotate with it. RMF separation uses this fact to rotate the ferromagnetic particles in a rotating field. In contrast, paramagnetic particles have a magnetism that can point in any direction with almost equal ease, and these will not rotate in a rotating field. By making use of this difference in magnetic properties, RMF rotation separation can separate ferromagnetic particles from paramagnetic, even when the particles have similar susceptibilities. Some particles such as both chrome spinel and ilmenite can contain ferromagnetic regions within a paramagnetic matrix. These ferromagnetic regions can vary from very small regions dispersed throughout the crystal, through thin lamellae, to larger more bulky regions. Although most natural ilmenite is ferromagnetic and generally has a higher magnetic susceptibility than paramagnetic chrome spinel, the susceptibility ranges for the two minerals overlap considerably (Allen, 2000a) due to the presence of these ferromagnetic elements, frequently making the conventional magnetic separation of these two minerals impractical. It is known that roasting a mixture of ilmenite and chrome spinel particles increases the magnetic susceptibility of the ilmenite while leaving the spinel susceptibility substantially unchanged. This makes the use of conventional (susceptibility attraction) magnetic separation more practical for the separation of these two minerals. However, very little is known about the effects of roasting on the response of ilmenite and spinel particles to a rotating magnetic field. For example, although the optimal ilmenite roasting conditions for conventional magnetic separation are quite well established such conditions may or may not be optimal for RMF rotation separation. Low intensity conventional magnetic separation on the basis of magnetic susceptibility can be made more accurate if it is carried out in a rotating field, because the rapid spinning of the separating particles prevents the formation of magnetic flocs, and reduces entrapment and entrainment. Medium intensity RMF rotation-only separation (no attraction component) has the ability to separate rotating (ferromagnetic) from non-rotating (paramagnetic) particles, irrespective of their relative magnetic susceptibilities. RMF rotation separation is of particular interest in this case because ilmenite particles generally rotate much better than the mainly paramagnetic chrome spinel particles, and roasting could enhance this difference further. Further information on the use of RMF to separate minerals can be found in Allen (2000a; b and c). The aim of this series of tests on a number of Australian ilmenites was to compare some different oxidising and reducing roast methods and to establish whether the use of RMF rotation separation improves the chrome spinel rejection.

Jan 1, 2001

By Lawson F

Chrome chemicals are commercially produced by the alkali roasting of chromite ores with sodium carbonate. Results of tests conducted in a laboratory furnace indicated that the sodium carbonate reacted rapidly with part of the gangue material to form a metastable intermediate that later reacted further with the chromite. For the conditions used, the recovery of water-soluble sodium chromate was able to be described empirically as yield % = a tn with a = 0.24 T - 241.3; n = 3.90 - 3.12 × 10-3 T and t is the reaction time in hours.The major rate limiting step in the overall reaction sequence appears to be the rate at which oxygen can get to the reaction sites across the liquid film coating the solid reactants.Sodium sulfate alone was found to be an unsatisfactory source of alkali for reaction with chromite. However when limestone also was added in quantities sufficient to allow the reaction CaCO3 + Na2SO4 + H20 ? Ca SO4 + 2NaOH + CO2 to take place, the results obtained were comparable to those found when sodium car-bonate was used.For chromite particles in the size range -124 + 105 µm, the use of stoichiometric excess of sodium carbonate did not appear to increase the yield or the reaction rate significantly. However, with smaller sized particles, - 53 µm, increased yields of water-soluble chromate were obtained when roasted with more than the theoretical quantity of sodium carbonate.

Jan 1, 1984

By J Foster

The Lanfranchi Nickel mine is located approximately 48 km south of Kambalda in Western Australia. Mining first commenced in the mid-1970s under the previous owner, Western Mining Corporation Ltd. After two years on care and maintenance, Panoramic Resources (previously known as Sally Malay Mining Ltd) purchased the operation in November 2004. The site currently produces approximately 10?000 tonnes of nickel metal annually from approximately 430?000 tonnes of ore. The Ore is mined from four main orebodies; Deacon, Helmut South, Lanfranchi and Schmitz. The Helmut South orebody is situated approximately 790 m below surface and extends to a resource depth of 940 m. Horizontal thickness of the orebody ranges from 10 m to 45 m in width, with the average being 30 m. Previous mining at the Lanfranchi operations specifically the Helmut orebody, had a history of seismic activity. When Panoramic Resources acquired the operation it was decided that seismicity was going to be an issue and therefore a mining method needed to be selected that could effectively manage this potential risk. The dip of the orebody is quite shallow at 45º, with a 30º plunge to the south . The hanging-wall comprises of very weak ultramafics. Due to these factors the orebody posed several mining challenges. To safely and effectively mine the Helmut South orebody in the Lanfranchi Nickel mine, underhand cut and fill mining was selected as the most appropriate mining method. Paste fill comprising of cemented gold tailings was the backfill of choice. This paper is intended to convey some of the key learnings from the use of a mining method that has not been commonly practiced in Australia.

Mar 21, 2011

General Gold was discovered in quartz veins at Wiluna in 1896, and the first lode was discovered in 1904. Since 1896, some 2.5 million ounces of gold have been produced from the Wiluna area. The mining operations at Wiluna are 100 per cent owned by Wiluna Gold Pty Ltd, a wholly owned subsidiary of Wiluna Mines Ltd. Oxide and sulphide gold ore is extracted by conventional open pit mining techniques, and ran-of-mine ore is processed through two separate circuits. The oxide circuit has a capacity to treat 600 0(X) tonnes per annum and the sulphide circuit has a capacity to treat 400 (XX) tonnes per annum. Additional gold is won by dump leaching sub-grade oxidised ore and by retreating of primary ore flotation tailings from previous operations. Testwork carried out in 1990 indicated the viability of leaching dumps of run-of-mine oxide ore, and in June 1991 Signet Engineering of Perth, WA, was awarded an EPCM contract to construct a nominal 2.5 million tonne dump leach facility, for a total construction estimate of 51.75 million.

Jan 1, 1994

By M Weeks

Melbourne Water Corporation, through the Pipelines Alliance, has commenced construction of a new drainage pipeline to provide additional flood protection within the Sandgate Avenue Main Drain catchment, in order to mitigate against the risk of flooding of Frankston’s central activity district (CAD).The project involves the construction of a 1550 m long, 2.5 m internal diameter tunnel, commencing upstream at the Monash University Peninsula Campus and traversing approximately west to the outlet located at Kananook Creek. The tunnel was excavated by a dual slurry-earth pressure balance tunnel boring machine (TBM), with the depth to tunnel crown ranging from 0.7 m to 14 m below the natural surface level. The TBM navigated 500 m radius curves, with a maximum drive length of 608 m. The tunnel lining consists of 2.5 m internal diameter, 250 mm thick reinforced concrete jacking pipe.The geotechnical conditions along the tunnel alignment consisted of mixed face ground conditions, predominately clay, with clayey sand and sandy clay and some sand deposits near Kananook Creek.This paper presents the challenges associated with the operation of the slurry separation plant during tunnel construction. In particular, the paper focuses the impact of slurry separation on tunnel advance rates, the lessons learnt during construction with regards to slurry separation and on the decision to adopt a dual slurry-earth pressure balance shield TBM. In addition this paper highlights the importance of having a thorough understanding of the slurry separation requirements on a slurry TBM project prior to selecting the necessary plant.

Mar 8, 2011

Sphalerites from Devonian cassiterite-sulphide deposits and Pb-Zn-Ag fissure veins have similar ranges of Cd contents, but the average Cd and Fe contents could indicate a small initial difference in availability of Cd between the Zeehan-Renison Bell district and the Mt. Bischoff-Waratah district. Sphalerites from banded Pb-Zn deposits (Rosebery and Hercules) are characterized by low Cd content which is a world-wide feature of such deposits in exIrusive rocks, and may indicaIe a genetic relationship between ore deposition and vulcanism.

Jan 1, 1968

By J Theiler, B Beamish

The presence of reactive metal sulfide minerals in waste rock contributes to the hazard of spontaneous combustion in dumps, as these minerals react with air and water entering the dump at ambient temperatures to form various mineral products and significant heat. This reaction series can also be an initiator of self-heating of carbonaceous material present in the waste rocks if sufficiently high temperatures are reached. Characterisation of these reactive minerals has primarily been to assess the risk of acid mine drainage, which is not necessarily an indicator of spontaneous combustion risk. No systematic testing procedure has been adopted by industry to assess the spontaneous combustion propensity of the waste rock. As a consequence, the principal management strategy for spontaneous combustion has been a reactive approach of dealing with events as they arise.Recent advances in adiabatic oven-testing have enabled more definitive assessment of the spontaneous combustion propensity of coals, including the quantification of the accelerating influence of reactive pyrite (Beamish and Beamish, 2011, 2012; Beamish, Lin and Beamish, 2012). This same test procedure has been used to assess the self-heating performance of metal concentrates and is therefore amenable to assessing the metal sulfide oxidation process from low ambient temperatures. The data obtained from such testing can be used to quantify the more prone waste rock sequences of a mineral deposit in advance of mining. This enables appropriate management planning for emplacement and long-term storage of waste rock in dumps.CITATION:Beamish, B and Theiler, J, 2016. Characterising the spontaneous combustion propensity of waste rock, in Proceedings Life-of-Mine 2016 Conference , pp 93–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

Water Balancing in Mineral Processing - Issues and Opportunities

Sep 13, 2010

By S Talu, E Savage, P Sturm, A van As

It is estimated that substandard ground support installations and elements cost the Rio Tinto Copper Group millions of dollars between 2000 and 2014. These issues have also created significant safety and financial risks in Rio Tinto mines. As a result, Rio Tinto Copper has developed CaveCAD, an integrated system to collect, store and analyse all ground support-related data. The CaveCAD system stores geotechnical data and has the ability to automatically import data, collect data through tablet applications, report processed/analysed data and present this data through 3D visualisation software.The CaveCAD Ground Support module closes the design–implementation–verification loop by providing a method of verifying the compliance of all installed ground support, recording manufacturer specifications, recording quality control test compliance and rectifying any non-conformant areas. The module uses innovative technology to create value through cost saving, safety improvements and data collection efficiency. Cost savings will be achieved by a decreased need for excavation rehabilitation, less ‘waste’ due to faulty installation and quality assurance checks reducing the likelihood of substandard support units being used. Data collection will be improved through the use of a mobile tablet application that can be used underground in ‘off-line’ environments.CITATION:Savage, E, Talu, S, Sturm, P and Van As, A, 2016. Development and implementation of the CaveCAD ground support module for cost and safety improvements in block cave mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 769–772 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016