Search Documents

The Ranger Project Area covers 78.6sq km and is approximately six km east-west by 14km north-south (Fig. 1). The area is known to con- tain two uranium orebodies, Ranger No. 1 and No. 3, two uranium occurrences, Anomalies 4 and 5 and three significant radon anomalies, Ranger 18, 19 and 48. The Ranger No. 1 and No. 3 Orebodies con- tain approximately 120 000 tonnes of U308 in highly chloritised metasediments of the Lower Proterozoic Cahill Formation. The orebodies occur as suboutcrop and exhibit significant radiometric anomalies. These occur within approximately 400m vertically of the projected unconformity with the sandstone of the Middle Proterozoic Kombolgie Formation. Oxidised and reduced uranium minerals occur in quartz-rich schists containing variable muscovite, chlorite and sericite and in the chloritic matrix of chert breccia. Secondary uranium minerals namely saleeite, metatorbernite and gummite associated with earthy iron oxides occur from the surface to 50m depth in No. 1 Orebody and up to 80m depth in No. 3 Orebody. Below the oxidised zone, uranium occurs as pitchblende finely disseminated throughout sequences of quartz muscovite chlorite schist up to 150m thick and as open space fillings in zones of structural deformation. The uranium-bearing schists directly overlie up to 300m of dolomite and magnesite containing minor interbedded schist units and are themselves overlain by approximately 2 000m of more micaceous schists of the upper part of the Cahill Formation. Regional metamorphism has occurred to at least amphibolite facies and has been followed by retrograde metamorphism to a greenschist facies equivalent. The metasediments are intruded by granitic pegmatites and dolerites. Uranium is associated strongly with chlorite of which there are at least five textural varieties. Not all of the various generations of chlorite have associated uranium. Graphitic schist horizons occur which are often less than one metre thick and discontinuous. These are best developed at the base of the quartz chlorite schist sequence where uranium grades up to 1 000ppm U may extend for several hundred metres beyond the main ore zone. Uran- ium is not common in the carbonate sequences and only occurs in chlorite segregations in disrupted zones. The unoxidised ore contains sulphides, mostly pyrite, which are low in abundance (

Jan 1, 1984

By Kruse JW, Kjar AR

Recently there has been increased recognition o'f the cost savings that can be achieved by the greater use of offsite preassembly for the construction of industrial plants. Preassembly is a method of construction which involves considerable offsite assembly of complete sections of an industrial plant in established fabrication shops. The preassemblies are transported to the plant site, often by large and oversize transport systems where they are set on prepared foundations, finished and interconnected to other sections of the plant as required. The concept of preassembly is not new, but widespread interest has been shown because site construction costs in all parts of the world have increased rapidly and often at a greater rate than in established fabrication areas. Particular interest has be focused on remote, isolated and inhospitable plant site locations. These areas require the import of skilled labour, the payment of high labour rate premiums and the development of infrastructure to support the workforce for the duration of the construction period.

Jan 1, 1983

By Neill T. J, Howarth D. F, Malcolm J. McPhersqn

For many years Isa Mine has seen the need for a continuous mining machine which will economically cut hard rock. Tunnel borers are unsuitable due to the size and inflexibility of the machine and the shape of excavation mined. The design of roadheader type machines will not permit the use of the necessary cutting technology. in 1983 a joint project was undertaken by The Robbins Company and Mount Isa Mines Limited to develop and to trial a machine suitable for cutting hard rock in an operating mine. The project was based on the proven technology of raiseboring applied to horizontal development. The Mobile Miner was fabricated and trialled in a disused quarry in the U.S.A. during early 1984. Following these trials, the machine was transported to Mount Isa and commenced mining in September that year. The initial duty was to continue the development of a decline commenced by conventional mining for a conveyor system to serve the deeper southern areas of the 1100 copper orebody. This system will permit direct tipping of copper ore to a new crusher complex and conveying of the - crushed ore approximately 2 kilometres to the central hoisting shaft facilities. The Robbins Mobile Miner MM120-3001 uses a vertical rotating cutting wheel mounted on a horizontal swinging boom to excavate a nominally rectangular shaped heading. The cuttings are collected on an apron and conveyed back through the machine. The resulting excavation is smooth-walled with no blasting damage to the surrounding rock. This provides a safer working environment than does conventional drill and blast development mining. Ground support requirements are considerably reduced.

Jan 1, 1986

By C Gourdon

The present study concerns a new type of mixer-settler unit where coalescence is promoted by means of the phase inversion method (MSPI). Using two different systems (alkaline etching solution û LIX 54 in kerosene and acidic aqueous solution û LIX 984 in kerosene) the influence of the total flowrate, the A/O phase ratio and the hydrodynamic conditions in the nozzles of the scattering device on the extraction and separation efficiencies are studied. Two modes of operation are clearly outlined and a theoretical model predicting the separation efficiency is proposed and compared to experimental results. A comparison between mixer-settlers with classic decanters and the MSPI unit has demonstrated the advantages of the latter where throughputs in the range 20 -25 m3.m-2h-1 can be easily realised.

Jan 1, 2000

By P A. Grossman, J H. Rubinstein, M Brazil

The installation of truck turntables at above-ground crushers has the potential to yield gains in efficiency and productivity by eliminating the need for the trucks to turn around and reverse up to the crusher to dump their loads. The benefits include savings in time, fuel consumption and tyre wear. In addition, having a smaller area near the crushers dedicated to manoeuvring the trucks can be a significant benefit at some sites. Safety is also enhanced using turntables.This paper describes a project with the Australian Turntable Company to develop software that generates near-optimal layouts for the paths taken by the trucks in the vicinity of the crushers when turntables are present or absent. The geometry of the paths is constrained by the turning radius of the trucks and by the boundary of the manoeuvring area. The software quantifies the benefit of installing turntables by generating a design for paths with turntables and comparing it with the layout in current or planned use by the mining company. Through the use of this software tool, a mining company can readily assess the benefits of using turntables at their site.CITATION:Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2014. Demonstrating efficiency gains from installing truck turntables at crushers, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 259–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By S Girard, L Rowland, V Lawson, Y Shields

Since 1948, ValeÆs Matte Separation Plant has been successfully using magnetic separation and froth flotation to separate the copper sulfide, nickel sulfide and Ni-Cu metallic alloy contained in Bessemer matte for downstream processing. Though some equipment upgrades have been performed over the years, the flow sheet has generally remained unchanged since the early 1970s. The need to improve metallurgical performance led to the trial of a scalping flotation column to produce a final copper concentrate ahead of the cleaner circuit feed to take advantage of a high degree of copper mineral liberation, reduce cleaner-recleaner circulating loads and decrease the associated loss of selectivity. Plant results indicated that 50 per cent of copper contained in the rougher concentrate could be recovered at final grade target. Results indicate that up to a 1.5 per cent increase in copper recovery to copper concentrate was achieved during the scalper trial due to a reduction in the generation of fine chalcocite which has historically been observed to report to flotation tailings due to surface contamination. Deficiencies are currently being addressed and a long-term trial is scheduled to confirm the benefits of copper scalping.CITATION:Girard, S, Rowland, L, Shields, Y and Lawson, V, 2012. Copper scalping at ValeÆs matte separation plant, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 299-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By J R BISHOP

Geophysical techniques are being increasingly used down exploration drill holes as deeper and more elusive targets are sought. This paper lists the various methods available and discusses the applications using a number of examples.

Jan 1, 1992

By K G. van den Boogaart, S Konsulke, R Tolosana Delgado

Adaptive mineral processing has to rely on spatially predicted information on primary geometallurgical parameters, like phase composition, size and shape distributions of grains from various phases, portions of value elements in different grain types. Naively, one would predict these parameters geostatistically and select an optimal processing for the predicted structure. This is suboptimal, due to various kinds of non-linearities in the problem. First, some primary geometallurgical quantities themselves are measured in non-real scales, like compositional or stereologically distorted geometric information. Standard geostatistics has to be replaced by compositional and geometric geostatistics, involving complex transforms and restrictions. Further, only partial and uncertain information is available, introducing a stochastic character to the optimisation problem. Moreover, many response variables leading to costs, outcomes and eventual effects of later processing depend non-linearly on the primary geometallurgical parameters, which implies that the final monetary value is not estimated unbiasedly by kriging. Finally unbiased linear prediction (such as kriging) is not the best method of prediction for decision making. The conditional expectation of the monetary values is needed instead. The impact of these problems is explained in this paper, with simplified examples, and a first approach to a general solution is proposed. CITATION:van den Boogaart, K G, Konsulke, S and Tolosana Delgado, R, 2013. Non-linear geostatistics for geometallurgical optimisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 253-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Mike Sharwood

This subject is to be discussed in greater depth by Mike Sharwood. It has also been the subject of a mini-symposium by the Melbourne Branch of the AusIMM in October, 1993. The papers from this symposium were distributed to the membership late last year "to raise their consciousness and to promote greater awareness and understanding of the wide range of liabilities that may arise". An introductory paper by Nicholson outlined the many areas in which liability may arise with particular emphasis on expert reports, eg: Takeovers Schemes of arrangement Acquisitions from associates Prospectuses Related party transactions Directors' duties Continuous disclosure Other influences (environmental, occupational health and safety, trade practices)

Jan 1, 1994

The Mt Lyell Mine at Queenstown, Tasmania was re-opened in 1995 by Copper Mines of Tasmania Pty Ltd, a wholly owned subsidiary of Mt Lyell Mining Co Ltd. The re-opening followed over 100 years of copper and gold mining at Mt Lyell. Major changes in practice were implemented across the site. Preventing further damage to an already disturbed environment was a major priority. Sublevel caving, at a lower cut-off grade, replaced open stoping for the deep underground mining. Development and later stoping are handled by a contractor, National Mine Management Pty Ltd, in the largest underground contract awarded at the time. Large scale sublevel caving was new to Mt Lyell and not widely practised in Australia, requiring studies and systematic development of the method, particularly in drilling and blasting. Rehabilitation and upgrading of mine infrastructure have been and will continue to be a challenge. The mine has, since 1995, returned to being a stable producer with potential for growth.

Jan 1, 1998

By K Edwards, A J. J Mouton

Hematite represents the vast majority of iron ore exported from Australia as the development and processing cost of magnetite is generally seen as a barrier to the development of vast magnetite resources. However, a number of magnetite projects have attracted a significant amount of interest and investment from large Chinese steelmakers.This paper compares the relative merits of the development of Australian magnetite and hematite ore from the point of view of the steelmaker, taking into account the factors that influence the capital costs of the development of the ore types and the relative costs of operating the process plants to treat these ores. By modelling the relative operating cost for the production of hot rolled coil in China for the two ore categories, the paper demonstrates the economic drivers behind the Chinese steelmakers’ large investments in the magnetite resources of Western Australia. It does this by estimating the potential value of magnetite concentrate to the steelmaker in the event that the maximum potential is realised by operating the blast furnace with a 100 per cent pellet burden.Under the conditions described, it was found that direct reduction (DR)-grade magnetite concentrate could command a price premium over 62 per cent Fe fines of up to 46 per cent (December 2014 on a cost and freight (CFR) basis). The corresponding premium for blast furnace (BF)-grade magnetite concentrate is 17 per cent, which demonstrates the dependency on grade.The capital expenses for a 14 Mt/a concentrate plant is estimated at US$3.1 B for BF-grade magnetite and US$3.35 B for DR-grade, with operating expenses at US$45 and US$50 respectively. The corresponding free on board price for a break-even net present value is calculated at US$82/t for BF-grade magnetite and US$90/t for DR-grade. The minimum long-term iron ore price (62 per cent Fe) that would be required to underpin such a project is estimated at US$78/t CFR for BF-grade magnetite and US$68/t CFR for DR-grade concentrate.Apart from the financial benefits, it is demonstrated that the use of magnetite concentrate in ironmaking has the potential to reduce CO2 emissions by approximately 400 kg per tonne of hot rolled coil.CITATION:Mouton, A J J and Edwards, K, 2015. Magnetite – a higher-grade blast furnace feed and its potential benefits for the ironmaker, in Proceedings Iron Ore 2015, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Dinuzzo P, Wychie J, Desoe C

The Selwyn Gold-Copper Mine is located 150 km southeast of Mount Isa within Proterozoic units of the Mount Isa inlier (Figure 1). Mineralization in the mine area is associated with strongly sheared ironstones and iron rich schists at the base of the mid- Proterozoic Staveley Formation. The ironstone horizons outcrop as a series of dominant ridges over a 10 km strike. Economic gold-copper mineralization has been defined in 4 separate zones within a 3.5 km length of the outcropping ridges. A current combined geological resource for the deposits is 5.3 million tonnes of 5.0 g/t Au and 2.02 Cu. Weathering of the deposits has resulted in a pronounced vertical zonation of mineralogy, especially copper, within the ore zones. This has produced 3 separate ore types which require different treatment techniques. The categorization is based on copper content and zones are termed leached (surface), oxide and sulfide. Ore removed from the pits will be mainly leached and oxidized with minor sulfide near the pits final depths, while the underground ore will be from the sulfide zone with minor oxide in some areas.

Jan 1, 1989

By A Audétat, W T. Li

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Middle and Lower Yangtze River metallogenic belt is one of the most important polymetallic resource areas in China. Iron oxide-apatite deposits, mainly distributed in Ningwu and Luzong volcanic basins, are a distinct type of iron deposits in this region. These deposits have a close temporal and spatial relationship with Mesozoic dioritic porphyries and are characterised by magnetite-apatite-pyroxene/actinolite ± anhydrite assemblage and large-scale sodic-calcic alteration.Widespread multiphase inclusions in pre- to main-mineralisation stage pyroxene and garnet in Meishan (in the Ningwu basin), Luohe and Nihe (both in the Luzong basin) iron deposits were trapped at ~780°C in extremely saline brines (~90 wt per cent NaCl equivalent), consisting of Na (13–24 wt per cent), K (7–11 wt per cent), Ca (~7 wt per cent), Fe (~2 wt per cent), Cl (19–47 wt per cent) and SO4 (3–39 wt per cent), based on petrologic, microthermometric, Raman spectroscopic studies and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analyses of natural fluid inclusions and synthetic analogues. The high Cl/Br, Na/B and S/B ratios in brine inclusions and the heavy sulfur isotopic values of anhydrite and pyrite (d34SAnh = +15.2 to +16.9‰, d34SPy = +4.6 to +12.1‰) suggest a significant contribution from both halite- and anhydrite-bearing sedimentary rocks. The involvement of evaporites caused the production of large amounts of high-salinity brines with apparently enhanced capacity to extract iron from the dioritic intrusions.According to their geologic features and the above characteristics, these iron oxide-apatite deposits are considered to be a special type of iron oxide copper gold (IOCG) deposits characterised by high contents of Na, Ca, Cl and SO4 in the ore-forming fluids. Moreover, we believe that evaporite-bearing sedimentary basins are more prospective than evaporite-free ones for these kinds of deposits.CITATION:Li, W T, Audétat, A and Zhang, J, 2015. The connection between evaporites and iron oxide-apatite deposits, Yangtze River, China – laser ablation inductively coupled plasma mass spectrometry analysis of Na, S, Cl and Br in fluid inclusions, in Proceedings PACRIM 2015 Congress, pp 623–630 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The purpose of this paper is to look at the costs of tailings disposal, and in particular the comparative costs of different disposal methods in different situations. Costs are often the hidden design parameter. We know that they are important but sometimes feel that it is not very respectable to talk about them in public. It is better from a public relations point of view for it to appear that the decision-making process is driven by environmental factors or best practice rather than looking for the cheapest option. But this presumes that the two are mutually exclusive and this need not be so. These issues are discussed later in the paper. It is also commonplace for the scale of the mining operation to change with time, typically involving increased throughput rates and total tonnage. New ideas in tailings disposal make their appearance. The regulatory attitude can change. Having made a decision about the disposal method at the time of original feasibility study and design it is easy to suppose that the mine is æstuck with itÆ. But that also need not necessarily be so. Careful costing of options may reveal that a switch in method could be cheaper in the long run. The designer will often tend to think in terms of initial earthworks and site development costs. Aspects of power consumption, labour, and periodic campaigns to move tailings pipelines and carry out embankment raises are either overlooked or not given the same emphasis. This can distort the evaluation process. It is productive to think in terms of dollars or cents per tonne as a basis of comparison, not just the total sums. Tailings disposal can cost from as little as 10 - 20 ó/t to over $1.00/t which is a big range. There may be good and unavoidable reasons for the high figure but there would need to be to justify being so far over the industry average. At the same time, mining and processing costs, at least for gold, are around $15 - 20/t. Viewed from this perspective tailings disposal will always be a relatively small component of the annual budget.

Jan 1, 2000

By Nicol SK, Engel MD

Ion flotation involves the adsorption of ionic species, in association with surfactant molecules, at the surface of rising gas bubbles, for the purpose of recovering and concentrating those ions. The objective of this study was to optimise the ion flotation process using a heap-leach liquor, containing gold cyanide, and the surfactant cetyl trimethyl ammonium bromide (CTAB). The aim was to minimise the surfactant reagent dose, maximise the throughput of feed liquor in the process, and satisfy the dual constraints of a high gold recovery and a high volume reduction factor. Development of a first order model of the ion flotation process formed the theoretical basis for the test program procedure and the interpretation of the results. Batch tests were used in order to determine the ultimate recovery curve for the heap leach liquor-CTAB surfactant system. The results indicated that a surfactant dose of about 0.083 g/l would be necessary in order to achieve a satisfactory gold recovery. Continuous tests were then performed on a small-scale pilot plant at the Newcastle Laboratories. The optimum result achieved was a gold recovery of 85 per cent, a volume reduction factor of ten, and a feed throughput of 2.3 m3/m2-h. Recent work also indicates that very much higher volume reductions can be achieved using a larger diameter vessel. The improvement may be a consequence of a reduction in wall effects and hence an improvement in foam drainage.

Jan 1, 1993

Diamond drilling is a relatively new commodity in terms of drilling. The first known diamond drilling activities were carried out in the Swiss Alps around 1863 when the Swiss engineer M Leschot designed and made a tube with a diamond set face which was used in probing ahead drilling for the Mont Cenis tunnel (Figure 1). Craelius AB which today is a part of the Atlas Copco Group was formed in 1886. The name Craelius is a family name and the founder of the company was Per Anton Craelius (Figure 2). He went to the United States to study this new technology using diamonds to extract core samples and when he returned to Sweden designed his first diamond drilling machine. It was a man-powered drill needing a crew of six men, two to crank the unit, one to feed, two to power the flush pump and a foreman (Figure 3). As time passed through research and development, the original design was improved and manpower was substituted for steam engines and later combustion engines or electric motors (Figure 4). During the 1930s the drills radically changed designs and took the form of the short stroke drills which to a certain extent are still in use today. The original design of these drills have been refined during the years, hydraulic chucks, gear boxes and other improvements have been added.

Jan 1, 1995

Listing on Australian Stock Exchange Limited ('ASX') is a means by which a company can prosper and grow by gaining access to a large capital market. This currently stands at over $300 billion for domestic securities listed on ASX. A company seeking listing will benefit from a higher profile and a greater spread of shareholders. These result from, among other things, improved communications with the investment community. ASX recognises that a decision to list is an important step for a company. Owing to the diverse nature and size of the companies that consider listing and the various steps involved, it is recommended that guidance of professional advisers is sought as early as possible in the listing process. A company seeking listing on ASX must meet the prerequisites for admission to the Official List which, along with the continuing obligations that must be complied with following admission, are contained in the Listing Rules of ASX. Listing on ASX requires a company to ensure that, among other things, the market is fully informed at all times so that investors can make informed investment decisions.

Jan 1, 1996

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

Laboratory testwork was carried out on an overall orebody composite, of 2.9 per cent Cu and 4.2 per cent Zn, prepared from drill core taken from the Currawong fine-grained, copper-zinc massive sulphide deposit near Benambra in Victoria. While 90 per cent of the copper was readily recovered in a concentrate of 20 per cent Cu, after grinding to 95 per cent passing 38 microns, zinc responded poorly to conventional flowsheet/reagent regimes. Experience elsewhere with the use of reverse cleaning, to separate pyrite from sphalerite, led to a series of tests in which better (but still modest)metallurgical results were obtained. The best result was a zinc recovery of 55 per cent in a concentrate of 50.5 per cent Zn. The major loss of zinc occurred in the reverse cleaning stage where the unit recovery of zinc was similar to pilot plant results achieved at Mount Isa Mines on similar feedstock. Diagnostic mineralogy suggested that an overall zinc recovery of 70 per cent was probably the practical upper limit, at a 50 per cent Zn grade.

Jan 1, 1999

By C Claassen, R Balusu

Computational fluid dynamics (CFD) models have been developed based upon field data collected from a longwall mine in New South Wales, Australia to study the behaviour of goaf gas flow in both active and sealed goaf areas. A base CFD model was built to represent the goaf situations when the active longwall retreats near the finish-off line. Results from the base model were calibrated and compared against field goaf gas monitoring data. The base model was then used to carry out parametric studies to investigate a number of operational scenarios and their impact on goaf gas behaviour. CFD modelling results indicate that the overall goaf gas flow pattern changes as the operating longwall retreats towards finish-off line. In all cases, oxygen penetration into the active goaf remains high, reaching 15 per cent or higher, even at some 800 m behind the longwall face.The modelling results also indicated that it would be difficult for early detection of an active goaf heating (on the maingate side) based upon CO readings in the return airflow, as the main stream of the gaseous product will be flowing into the sealed deep goafs in adjacent longwall (LW) panels. Monitoring points (such as tube bundles and bag sampling points) should be selected at deep seated seals along the active goaf so that abnormal CO or C2H6 readings can be picked up for early detection and location of potential heating spots; goaf inertisation can be better achieved by injecting inert gas such as nitrogen at deeper points (>200 m) behind the operating longwall; the injection of in-seam drainage methane into the goaf areas will only have a limited impact on goaf inertisation as much of the injected methane will migrate towards deep and higher parts of the goaf due to its buoyancy effect.

Sep 26, 2011