Search Documents

The purpose of this study was to investigate the effectiveness of froth fl otation for the recovery of gold from the gravity tailing stream of the former Lihir Gold Limited (LGL) operation in Ballarat. The P80 of the tailings was determined by screen analysis as 1 mm, with test work conducted on as received material along with samples ground to P80 sizes of 47, 78 and 134 microns. Laboratory scale batch flotation tests were conducted at both natural and elevated pH to investigate the impact of pyrite depression on gold recovery. Results indicated that although an increase in grade from approximately 0.7 g/t to 3 g/t was achievable at a natural pH and a P80 of 134 micron, gold recovery was low at just 35 per cent. Finer grind sizes were found to have an adverse effect on both grade and recovery. Future efforts will be focused on the sub 310 micron size fraction of the tailings, which was revealed to contain approximately 85 per cent of the available gold and may be amenable to cyanidation or ultra-fine gravity treatment.

Aug 1, 2010

By I Villalba

The need to continue the development of the Ensham mine has led to blast up to 75 m to the Eastern side of a water dam in the vicinity of Ramp 23. The water dam wall is exposed to blasting over a distance of approximately 500 m. The first decision was to determine that the existing rock pillar between the Eastern side of the water dam and the blasting operations may not be less than 75 m in order to minimise the damage that the blast could generate to the dam wall. It was also necessary to define blasting practices to minimising the blast damage to the rock properties of the dam wall and to avoid adverse effects from vibration and gases generated by the detonation on structures.For this purpose analytical designs and test blasts were conducted to assess the ground vibration attenuation within the rock pillar. From this analysis, it was concluded that the best practice to reduce the rock damage was to create a zone of fractured rock adjacent to the side of each production blast. This fractured zone would create an effective filter both for vibration and for gases generated by the blast. This zone of fractured rock was created by firing two buffer rows. In terms of pattern size and powder factor the two buffer rows were designed just to generate a fractured rock zone. To date approximately 500 m have been excavated along the eastern wall of the water dam where each production blast was preceded by a Trim blast. This practice has given good results with regard to minimising the damage generated by production blasting.

Nov 8, 2011

Milling operations at Misima Mine are discussed, with specific reference to the application of energy and cost saving concepts. Design stage innovations and post-commissioning developments are covered. General operational problems are described with specific reference to problems associated with operating in a remote location.

Jan 1, 1994

By N Madani, S Abulkhair, N Morales

Conventional geostatistical algorithms cannot reproduce bivariate complexities such as inequality constraint, nonlinearity and heteroscedasticity. Poor reproduction of these features may decrease the accuracy and reliability of mine planning results. For example, it is not unusual to have an inequality constraint between primary and disturbing elements in a metalliferous deposit. Implementation of traditional methodologies for such complex data sets can lead to the incorrect reproduction of a bivariate relationship, which will affect the validity of NPV results. In this paper, an iron data set containing iron and silica grades with an inequality constraint between variables is introduced as a case study. This study proposes an algorithm based on a hierarchical sequential Gaussian cosimulation integrated with inverse transform sampling. The proposed methodology considers the linear inequation between two variables in the hierarchical cosimulation process to reproduce an inequality constraint. As a comparison, conventional sequential Gaussian cosimulation is also applied to the same data set to demonstrate the difference in bivariate relationships from both models. Unlike the proposed algorithm, the conventional cosimulation cannot reproduce an inequality constraint and slightly overestimates silica grades. The modelled realisations are then used to assess the uncertainty of a plan and generate a stochastic strategy that adapts the destination of the blocks depending on the scenario. Two-stage stochastic long-term production scheduling takes extraction decisions using average information (ie e-type model) and ore/waste destinations based on geostatistical realisations. As a result, the proposed strategy is closer to the upper bound, highest possible NPV for each realisation, than to the lower bound, deterministic strategy that does not manage the risk of sending extracted material to wrong destinations. Furthermore, Comparing production schedules resulting from proposed and conventional geostatistical methodologies shows the importance of inequality constraint reproduction and more accurate long-term mine planning.

Nov 8, 2021

By Fawcett M

Pine Creek Goldfields Limited (PCG) is rehabilitating the Enterprise Pit to an aquatic habitat and potential water resource. This paper discusses the development and implementation of that plan. Pine Creek Goldfields Ltd's Enterprise Mine is located approximately 230 km south of Darwin. Open cut mining of the orebody commenced in 1985 and continued for eight years with 14 million m3 of ore and overburden extracted. Geochemical testing of exposed rock types in the pit has demonstrated a propensity to produce acid, and dissolved metals. A plan of management has been developed and implemented to minimise the risk of acid formation and improve the overall water quality in the final void. In developing the plan prime consideration was given to reducing the potential for pit water to impact upon the regional groundwater. An interception system was constructed on Pine Creek to divert approximately 9 km2 of upper catchment into the northern end of the Pit. Construction of the diversion system was completed in December 1993 and a comprehensive surface and groundwater monitoring program initiated. The monitoring program and associated studies are also discussed.

Jan 1, 1994

By Ormsby W. R, Nicholson P. M

Woodcutters is a polymetallic vein-style deposit hosted by sediments of the Palacoproterozoic Whites Formation which forms part of the sedimentary sequence in the central Pine Creek Geosyncline. Past production and identified resources total over eight million tonnes at 5.5 per cent lead, 12.1 per cent zinc and 110 gA silver. The local geology is influenced by Archaean basement highs; the Rum Jungle and Waterhouse Complexes. Unconformably overlying basement are interbedded clastic and crystalline carbonate units (Batchelor Group) representing cyclic changes in the depositional environment. These exhibit onlapping features with the underlying rocks. Sediments of the overlying Frances Creek Group suggest a quiet period during subsidence and subsequent increase in water depth (the carbonaceous dolomitic shales and the interbedded dololutites of the Whites Formation) followed by proximal uplift resulting in the inundation of turbiditic flows (Acacia Gap Quartzite). All of the Palaeoproterozoic rocks show evidence of being affected by penecontemporaneous, basement circling faults with steep dips. The stress regime during the deposition of the Frances Creek Group was characterised by alternating episodes of thrusting and transpression. Periods of relaxation also occurred. The compression resulted in major NS strike-slip (transpressional) faulting, en-echelon NNE trending folds and NW-SE tensional cross faults. Thrusting produced N-S striking, steep dipping reverse faults and a possible decollement immediately above the Batchelor Group. Relaxation is evidenced by the intrusion of lamprophyre dykes and dolerite sills (Zamu Dolerite). Mineralisation at Woodcutters occurred in faults within the Whites Formation, probably synchronous with deformation and the deposition of the upper parts of the Frances Creek Group. Greenschist facies metamorphism occurred as the rocks were further buried. Several massive sulphide bodies occur at Woodcutters. A number of features influence the location and shape of these bodies. They are: ò the N-S transpressional faults and in particular associated dilation zones; ò intersection of the N-S transpressional faults with the axial plane of the NNE trending Woodcutters Anticline; ò intersection of the N-S transpressional faults with the NW-SE cross-faults; ò intersection of dololutite rich units with the NS transpressional faults where local replacement takes place; ò thickening of the lithological units in the vicinity of the anticlinal axis; and ò the anticline doubly plunging to both the north and south. The mineralisation exhibits vein-like features as well as epigenetic textures. Its boundaries are sharp, its thickness varies rapidly down dip and along strike, and no alteration halo exists though stringer veins of quartz-carbonate-pyrite ¦ sphalerite/galena occur in close proximity. A number of sulphide mineral assemblages have been recognised, each separated by periods of deformation and partially replacing the earlier assemblages. Vertically continuous zonation patterns highlight the presence of rich galena-sphalerite-silver in zones of maximum dilation and pyrite-arsenopyrite-gold concentrated at the along strike peripheries. The genetic model proposed has the mineralisation occurring whilst the transpressional regime was active. It was deposited from the same fluid that elsewhere in the Geosyncline formed the stratiform deposits higher in the sedimentary pile. Hydrocarbons sourced from the organic-rich Whites

Jan 1, 1994

In April, 1990 the Sydney Water Board invited bids for the construction of the Hazelbrook Carrier Section 3 being part of the Blue Mountains Sewerage Transfer Scheme. In December 1990 the contract was awarded to Costain Resources Limited, Mining Services Division for the sum of $A15.3 M. The works consisted of excavation of 9 520 linear metres of tunnel, 3.35 metres diameter with installation of permanent ground support in the form of rockbolts, mesh, steel sets, shotcrete and in situ concrete

Jan 1, 1993

By Coates D. F, Neil T. J, O&apos

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risks of slope fail- ure inherent in steeper slope angles. However, no formal framework for a proper analysis existed to date. This paper describes the results of the past four years' effort in which a formal eco- nomic analysis framework was developed and tested through a case study. This framework, in essence, consists of the availability of tested procedures and com- puter programs. The procedures as well as the programs are divided into two broad functional categories; (1) the first category related to assessing the economic benefits and costs associated with various pit slope angles and (2) the second category that determines the overall financial impact which the assessed benefits and costs exert to the mine operator's overall economic stature.

Jan 1, 1977

By C Nucifora, M Landers, J Jones, G Maddocks, K Mandaran, A Forbes, W Wilson, S Newman

Glencore’s Mount Isa Mines Limited (MIM) operates the Mount Isa open cut and underground copper (Cu) and zinc-lead (Zn/Pb) mines near Mount Isa in Queensland, Australia. Tailings from processed Cu and Zn-Pb ore is contained in a 1,315 ha shallow (< 35 m deep) multi-cell valley fill tailings storage facility (TSF). Static geochemical testing conducted by MIM over the life of mine (LoM) verifies that the Cu, and Zn-Pb tailings has a wide range in sulfide content and diverse mineralogy with significant acid neutralising capacity (ANC) in some samples. The tailings are predominantly classified as potentially acid forming (PAF) using static analytical methods. Kinetic leach testing using free draining columns and humidity cell tests simulating tailings placed on the surface of the TSF suggest that the tailings samples are likely to remain non-acid forming (NAF) for 10 to 40 years under aerial exposure, and much longer than this under saturated conditions within the TSF. During this period of weathering, as ANC is depleted, the neutral pH drainage may contain elevated concentrations of some elements including sulfate, manganese and zinc. Only when the ANC is depleted would the tailings then begin to produce acid drainage. CITATION:Mandaran, K, Jones, J, Nucifora, C, Maddocks, G, Landers, M, Forbes, A, Wilson, W and Newman, S, 2018. Mount Isa Mines Rehabilitation Materials Sampling and Analysis program for closure planning, in Proceedings Life-of-Mine 2018, pp 138–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By M Lee, J F. Carswell, G Reitsema

"The increased costs of underground mining have continually challenged engineers to identify opportunities for alternatives to common approaches to underground development. Considerations to the design of horizontal and vertical development at the Dugald River mine targeted inclined raise boring to reduce horizontal development, not only to reduce cost, but to allow development activities to focus on other areas of the mine.The mine plan consists of 50 raise bored ventilation shafts, of which 17 have been mined to date with diameters ranging from 3.1 m to 5 m and lengths from 30 m to 200 m. The expected performance and stability of these shafts has been determined using methodologies proposed by McCracken and Stacey (1989) and further refined by Peck, Coombes and Lee (2011). Actual raise performances have been collated and compared to a database of raise bore performances across Australia as presented by Coombes, Lee and Peck (2011), and form a database of raise bore performance specific to Dugald River.Opportunities to further optimise the mine plan and reduce costs have seen the introduction of large diameter-inclined raise bored ventilation shafts to minimise the required lateral development to connect the ventilation circuits. Large diameter inclined shafts ranging between 3.1 m and 4.5 m in diameter have been successfully mined with dips down to 70°, reducing the cost of lateral development by more than $1 million over the next two years.Both technical and operational challenges were overcome in the mining of large diameter-inclined raise bores, including modification of: existing methodologies of assessing shaft wall stability for inclined raises. These included variations of the McCracken and Stacey method and the utilisation of the modified stability number (N’) previously developed for stope performance (Potvin, 1988). both the collar and toe development profiles, including the general set-up of the raise bore drill rig to reduce the operational risks associated with angled raises.Due to their success, inclined raises have been designed for subsequent stages of the life-of-mine ventilation system at Dugald River. This has resulted in significant capital cost savings for the mine.CITATION:Carswell, J F, Reitsema, G and Lee, M, 2017. Vertical and inclined raise bore performance at Dugald River mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 313–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By P Joyce, D R. Cooke

The Dinkidi Cu-Au porphyry deposit is situated in the Caraballo Range of North Luzon, Philippines. Although comparatively small, Dinkidi has unusually high gold grades with drilling by Climax-Arimco Mining Corporation delineating a 110 Mt orebody at 1.2 g/t gold and 0.5 per cent copper. The magmatic-hydrothermal evolution of Dinkidi records a distinctive switch in mineralisation from an early orthoclase-dominated Au-rich assemblage, typical of alkaline porphyry systems, to a later quartz stockwork Au-Cu rich assemblage typical of most calc-alkaline to shoshonitic porphyry systems. The early orthoclase-dominated stage is associated with the intrusion and crystallisation of a variably-textured clinopyroxene-syenite dyke that contains high-grade (5 - 20 g/t) gold mineralisation. We consider this dyke to be a Cu-Au porphyry analogue to the pegmatites found in granitic systems. Dinkidi is hosted within the Early Miocene Didipio Igneous Complex. This alkaline igneous complex is comprised of early unmineralised gabbros (pyroxene-plagioclase cumulates), clinopyroxenites (pyroxene cummulates), diorites and monzodiorites that have been intruded by a large, weakly mineralised monzonite pluton. The Dinkidi deposit is located at the southern margin of the monzonite pluton. Mineralisation is hosted within a composite monzonite stock. Within the stock, an 800 metres by ~200 metres (plan section) elongate monzonite stock (Tunja Monzonite) predates and hosts the bulk of the Au-Cu mineralisation. This has been intruded by the thin (10 to 30 m wide), highly mineralised variably-textured magnetite- and clinopyroxene- phyric syenite pegmatite (the Balut Dyke). The youngest phases of the composite stock are leucocratic quartz-monzonite porphyry (Quan Porphyry) that grades texturally, in its core, into a post-mineralisation crystal-crowded quartz-syenite (Bufu Felsite). The late-stage Bufu Felsite is inferred to be the source of much of the Cu-Au mineralisation. The Didipio Igneous Complex has intruded a sequence of Late Oligocene alkaline andesitic lavas and volcaniclastics and overlying potassic dacitic lavas. Whole rock geochemical analyses indicate that the intrusions and the potassic dacite lavas in the surrounding region are co-magmatic. Five main stages of hydrothermal activity are recorded at Dinkidi. An unmineralised K-silicate (biotite-magnetite) alteration assemblage formed during the intrusion of the Tunja Monzonite stock. The diorites surrounding the stock display intense selectively pervasive biotite and magnetite alteration and are cut by an extensive network of orthoclase veins and monzonite dykes. The orthoclase-dominated assemblages of Stage Two carry substantial high-grade Au mineralisation and are associated with the intrusion of the Balut Dyke. The emplacement of this unusual dyke is associated with emplacement of pegmatitic clinopyroxene-orthoclase-magnetite¦sulphide dykes, localised orthoclase flooding along the margins of the dyke, and subsequent emplacement of an extensive orthoclase-actinolite-bornite¦chalcopyrite-fluorite stock-work, and development of widespread selectively pervasive actinolite alteration. The main stage of Au-Cu mineralisation at Dinkidi is intimately associated with the intrusion and initial crystallisation of the leuco-monzonite porphyry (Quan Porphyry) and emplacement of a quartz stockwork followed by carbonate-sulphide deposition and intense vein-related sericite and carbonate alteration assemblages. The quartz stockwork formed synchronous with the deposition of the æBugoy QuartzoliteÆ, a very coarse grained mosaic of quartz-orthoclase-perthite along the walls and top of the crystallising intrusion. Stage 3 was terminated by crystallisation of the distinctively vuggy Bufu quartz-syenite phase in the core of the intrusive, with associated antiperthite veins, and the subsequent explosive brecciation of the roof of the intrusion, forming a quartz-fragment breccia from the Bugoy Quartzolite. Retrograde metasomatism during Stage Four was intimately associated with the emplacement of extensive, late-stage carbonate, silica and zeolite veins and widespread selectively pervasive carbonate alteration. The last hydrothermal stage at Dinkidi, Stage 5, is comprised of strong selectively pervasive clay alteration and is associated with fault-related brecciation of the Dinkidi stock.

Jan 1, 1999

By K B. Quast

During the prefeasibility stage of the mining cycle for a gold deposit, an evaluation of the ore leaching characteristics from various defined areas is essential prior to plant design. There are a number of simple laboratory tests which have proven successful in establishing gold and silver leaching kinetics, carbon adsorption and fouling, as well as elution characteristics. A number of case studies of carbon-in-pulp (CIP) simulation are presented which show excellent agreement between calculated and assayed gold and silver grades in feed and adsorbed on carbon which validate the methods used.

Jan 1, 1998

By Matsuhisa Y, Sakurai W, Shimazaki H, Peiming H, Fukahori Y

Oxygen and carbon isotope mapping of hydrothermally altered wall rocks was applied to the blind ore prospecting of skam Pb-Zn deposits in the Kamioka mining district, central Japan, where the wall rocks consist of heterogeneous rock units. The results (8180sMow of -1.1 to +17.3%o and 613CPDB of -5.0 to +4.8%o for limestones, and 8180SMOW of -0.8 to +12.5%c for silicate rocks) show isotope zonations of the wall rocks with depletions in heavy isotopes (180 and 13C) toward the center of mineralization. The isotope zonations likely formed by interaction of migrating thermal waters with the wall rocks during the mineralization. The heavy-isotope depleted zone, which indicates higher temperature or higher water-to- rock ratio of the system, occurs in the footwall of a fault, indicating that the fault played the role of main conduit of the ore-forming fluids. A heavy-isotope depleted zone was also found in an area, where significant mineralization had yet to be identified. Recent drilling in this area has intercepted a zone with a grade of 16.0% Zn, 0.8% Pb, and 35g Ag per metric tonne at a depth of about 360m.

Jan 1, 1995

By E Ferrow, R Herbert, M E. Malmstr, M Fuchs

The study of microbial sulfide oxidation and oxidation rates of tailings requires the use of sterile control samples in laboratory experiments for comparison purposes. The need for sterile tailings sand is also apparent in the study of microbial communities and processes. This study compares six different methods with regard to sterilisation efficiency and investigates chemical and mineralogical changes in the samples as the result of sample treatment. In addition, the effect of sterilisation on mineral weathering rates is also studied. The efficiency of the different methods with regard to sterility is estimated by most probable numbers (MPN) of both sulfur and iron oxidising bacteria. The sterilisation methods that were compared are: washing with sterile water, washing with ethanol, applying antibiotics, repeated heating to 70¦C, autoclaving, and γ-irradiation. There are several possible drawbacks with the different methods, including the risk of an applied chemical acting as a substrate for micro-organisms in the system, and the risk of altering the tailings. The results show a substantial difference in sterilisation efficiency between the treatments. For example, autoclaving, repeated heating, ethanol and irradiation efficiently kill micro-organisms, rendering an undetectable amount of bacteria after one month of incubation, whilst washing with water exhibits virtually no microbiological effect, with a bacterial content comparable to the control. The use of antibiotics for sterilisation ranks intermediate: the lag-phase was twice as long in the antibiotics treatment compared with the controls. X-ray diffraction, optical and electron microscopy, M÷ssbauer spectroscopy, and mineral magnetism indicate no significant change in the bulk mineralogical composition. However, X-ray photoelectron spectroscopy analyses show that with some of the treatments, sulfides are partially oxidised, as indicated by the formation of sulfate and partially û oxidised sulfur species at the tailings surfaces. Aerated batch weathering experiments performed on sterilised tailings samples and untreated controls indicated that while the initial rates of element (S, Fe, Cu, Zn, Mg, Na, K, Ca) release may differ between the samples, over the course of ~100 days of experiment at pH 2 and room temperature, the rates declined toward a similar value for all samples. To conclude, there does not appear to be one perfect method for tailings sterilisation. Autoclaving and heating damage the mineral grain structure and oxidise the sulfide surfaces. Ethanol, antibiotics and rinsing greatly alter the pore water chemistry through the washing procedure. In addition, ethanol and denatured antibiotics might serve as a substrate and also, in the case of antibiotics, adhere to mineral surfaces thus obstructing chemical reactions. Irradiation seems to be the preferable method on an overall basis, although the formation of surface Fe3+ was suggested by M÷ssbauer spectroscopy.

Jan 1, 2003

By M J. Saynor, J B. C Lowry

The Ranger Uranium Mine is located in the wet-dry monsoonal tropics approximately 250 km east of Darwin in the Northern Territory of Australia (Figure 1). Mining of open-cut ore bodies commenced in 1980 (Pit 1) and ceased in 2012 (Pit 3) and milling and production are scheduled to cease by 2021. At the conclusion of mining and milling operations, mine tailings will be returned to the mined out pits 1 and 3, which must then be physically isolated from the environment for at least 10,000 years (Australian Government 1999). The final landform also needs to have sufficient mitigation measures in place to ensure that areas downstream are not impacted by erosion products from the mine site. The proposed post-mining rehabilitated landform will cover approximately 847 hectares (8.5 km2) which represents an area that has the potential to supply sediment to catchments and streams downstream. One method of reducing runoff and associated sediment is the construction of rip lines along the contour to slow down the runoff velocity and to also trap fine sediment and nutrients in the depressions to assist vegetation growth.CITATION:Saynor, M J and Lowry, J B C, 2018. The impact of rip lines on erosion at the Ranger Mine Site, in Proceedings Life-of-Mine 2018, pp 150–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

Graded macadam slag base has been used successfully by the Department of Main Roads, N.S.W., in the construction of Expressways. However, the use of graded macadam in urban conditions introduces problems which can be avoided by the use of material meeting the specification outlined in M.R. Form 744. This paper outlines the rationale behind the technical requirements of the specification for the "Supply of natural gravel or crushed rock for road pavement (bitumen surfaced) M.R. Form 744". A blend of materials produced from slag is proposed as a potential solution for the production of slag base which would be suitable for use in urban construction or maintenance of roads.

Jan 1, 1979

By Wright J

Large scale cut and fill mining in narrow silver-lead-zinc orebodies began at Mount Isa in 1964. Initially each orebody was one stope and access was via raises from the level above. Upholing was the principal mining method, although flatbacking was employed where ground conditions were more difficult. Developments since have included access via footwall inclines and connection of all stopes with major crosscuts. Flatbacking is the principal method. The most recent cut and fill operation is now fully mechanised using drilling jumbos, rockbolting jumbos and load-haul-dump units. Improved ground support and drilling and blasting practices have enhanced safety, recovery and productivity in all cut and fill operations.

Jan 1, 1988

By K Nilsson, G Cheong

Troy Resources NL acquired a 70 per cent interest in the Mina Sertpo gold project in Goißs State, Brazil, in 2001 following a successful bid for the highly competitive international tender of a tenement package put out by Western Mining Corporation (WMC). The Sertpo deposit is located on cleared grazing land 380 km west of Brasilia and is 30 per cent owned by Amazonia Mineracao Ltda, a private Brazilian company. It is a small high grade open-pittable orebody with a measured and indicated resource of 108 000 tonnes at a grade of 49.7 g/t for 172 500 ounces using a 2.0 g/t cut-off. Troy undertook the project management and development of the project while Amazonia managed the exploration activities and provided other services as required. The project development involved drilling metallurgical test holes, scouring the world to locate an available and suitable second-hand plant, and arranging shipping to andreconstruction in Brazil.

Jan 1, 2004

By J Pan

In this paper, the technology of producing fluxed pellets by using hydrated lime as binder instead of bentonite was carried out. The properties of the two types green balls (0.8 per cent bentonite and 2.0 per cent hydrated lime) were as follows: drop numbers of 4.8 - 5.0 times/0.5 m, compressive strength of 19.7 - 24.2 N/pellet and thermal shock temperature of 280° - 385°, respectively, under the same conditions of 1.5 per cent coke, 1.45 basicity and balling at 8.5 per cent moisture for 13 min in disc pelletiser. Comparing with bentonite as binder, the compressive strength of fired pellets with hydrated lime is elevated by 13.8 per cent and climbs up to 3113 N/pellet under the following conditions: preheating at 1050°C for ten minutes and fi ring at 1300°C for 15 min. In the mean time, the hydrated lime also improves the metallurgical performance of fired pellets. The reduction index was enhanced from 68.6 - 70.6 per cent, RDI+3.15+ increased from 90.1 to 98.8 per cent and reduction swelling index dropped from 22.4 - 7.4 per cent, respectively. The mineral compositions and microstructure of fi red pellets shows that the fired pellets containing 2.0 per cent possess more calcium ferrite and magnesium ferrite and compact microstructure, leading to the higher compressive strength.

Jul 11, 2011

Downhole survey uncertainties observed at various De Beers operations prompted an investigation into their possible effect on deposit shape and volume. An accurately surveyed artificial æboreholeÆ was constructed and different downhole survey instruments tested. In this way an empirically determined error range of 0.1 per cent to ten per cent was derived for downhole survey data. These survey errors were applied to an orebody model at an existing mine. Visualising the sphere of uncertainty associated with a borehole trace using a general mining package (GMP) gives an indication of possible volume variance. The resulting orebody maximum and minimum volume scenarios for three different depths (200 m, 500 m and 800 m) are presented. For certain instruments and borehole angles, the 3D positional error can be as high as 100 m at 1000 m down the hole. At depths below 200 m the resulting volume deviations can become significant for borehole survey errors exceeding 0.35 per cent. At 800 m depth the volume difference can approach 25 per cent. These figures assume that the error is compounded. The impact of these downhole survey errors is greatest for pipe-like orebodies such as porphyries and kimberlite pipes. Subhorizontal sill-like orebodies (and coal seams) will not be significantly affected by these errors. The impact of this type of survey error needs to be stated (and quantified) and is significant in JORC classification.

Jan 1, 2009