Search Documents

By X Ling, M Barati, E Moosavi-Khoonsari

In the pyrometallurgical process of secondary lead recycling, a desulfurising agent, such as Na2CO3 is added to minimise the emissions of sulfur into the atmosphere, while silica is introduced into the smelter as a fluxing material. Subsequently, a significant amount of Na2O and SiO2 remains in the downstream reverberatory furnace and blast furnace slags. However, there is limited understanding of the thermodynamic behaviour of silicate-based lead slags rich in Na2O, posing challenges in accurately determining the optimal condition for targeted metal recovery and final slag composition. In this work, the equilibrium phase relations of the PbO-Na2O-SiO2 system in the primary phase field of Na2SiO3 are studied from 800 to 1000°C via equilibration-quenching method. Samples with different compositions were prepared and held in platinum capsules in air at these temperatures to reach equilibrium. The equilibrated samples were subsequently quenched and the phase compositions were measured by electron probe microanalysis (EPMA). The results were then compared to those of previous studies and any discrepancies were resolved.

Jun 19, 2024

By Johnston R. F

The factors which influence the reduction of chromite are investigated with special reference to Coobina chromite. This was compared with a South African chromite ore. The reduction characteristics are outlined and the reduction kinetics studied Temperature has the most significant effect, followed by particle size, silica addition and type of coal.Electron microprobe analysis of the products indicates that iron in the chromite is first reduced at temperatures above 1100°C, followed by chromium at around 1200°C. At temperatures greater than 1200°C metallic iron and chromium are formed simultaneously and subsequently give an iron-chromium-carbon alloy. It was observed that the metallic carbide contains a small amount of silicon. The decomposition of the chromite spinel was observed to pass through the FeO.Cr2O3, MgO.Cr2O3 and MgO.AI2O3 forms before slag formation. It is concluded that Coobina chromite is suitable for the production of ferrochrome if direct prereduction followed by intensive bath smelting is used.

Jan 1, 1994

By G M. Zhomin, A S. Arkhipin, A Kondratiev

Viscosity of multicomponent slags is one of the crucial physicochemical properties for many industrial processes and technologies. While the viscosity-temperature relationship of completely molten slags can well be described by an Arrhenian-type law, the compositional dependence of viscosity is still not fully understood, especially in compositional regions with the lack of experimental data (eg at the glass-former concentration of 90 molar per cent or higher). In the present work major compositional relationships of the activation energy of viscous flow have been revised for numerous binary and ternary slag systems on the basis of experimental data collected and stored in the viscosity database OxiVis. For example, it has been found that the activation energy relevant to the polymerisation effect in binary systems of the MO-GFO type, where MO is the modifier oxide (ie monovalent K2O, Na2O, Li2O and bivalent CaO, MgO, BaO, MnO, PbO etc) and GFO is the glass-forming oxide (SiO2 or B2O3) is not always proportional to the third power of XGFO (contrary to the Urbain formalism) and can vary significantly dependent on the slag system. Also, the activation energy of the charge compensation effect has been revised for ternary systems of the AO-MO-GFO and AO-MO type, where AO is the amphoteric oxide (Al2O3, Fe2O3 or other). A simple polynomial model has been proposed on the basis of the carried-out analysis for estimation of viscosities of multicomponent slag systems. The model has been optimised against the experimental viscosities in the selected binary, ternary, and higher-order oxide systems and has been shown reasonable agreement with the experimental data.

Aug 21, 2024

By Hargraves AJ

Pre-drainage experiments have been conduct- ed at Appin, Cook, John Darling, Leichhardt, Macquarie, Metropolitan and Moura No. 2 Collieries. Appin (550 m deep) experiences particular gas problems in development drivages, and the almost pure CH4 seam gas makes difficult tiro compliance with statutory maxima in intakes and returns. Patterns of 43 mm diameter drain- a,.;e holes drilled ahead and laterally into virgin coal have improved gas conditions in working places and have allowed tolerable advance rates. Cook, Leichhardt, Metropolitan and Moura No,. 2 Collieries have experienced gas and stress phenomena ranging from conical bursts less than one tonne to full scale instantan- -us outbursts of hundreds of tonnes with tens ,f thousands of cubic metres of seam gas. Gas ~Irainage experiments with patterns of holes up a,, 200 mm diameter have been undertaken with ;,;siness monitors on the coal to establish .lative effectiveness. Incremental flows into mg 43 mm diameter boreholes have investigated drainage patterns relative to length, and at comparative incremental flows have nlicated lowered permeability zones at stress ,.,utments. In some CO2 seam gas areas where iammability problems are reduced to perhaps ii, but where outbursts proneness is increased,

Jan 1, 1982

Access to the Rosebery Orebody, which dips into the western slopes of Mount Black at 45¦, has been achieved in sequence by the following means: - A series of adits down to 8 level - An inclined shaft (No. 1 Shaft) sunk internally from 8 level to 14 level - A vertical circular concrete lined shaft (No. 2 Shaft) sunk internally from 4 level to 19 level. Although the orebody has been fairly well defined to 19 level, deeper ore occurrences have been outlined by a series of drill holes decreasing in frequency with depth to 26 level. No. 2 Shaft (sink) was stopped some 10 m below 19 level in order to make an early start on doubled production at West Coast Mines, with the intention of subsequently extending the shaft or of driving a decline from the lowest operating horizon for deeper access. The decline approach was adopted some six years after production commenced from No. 2 Shaft. The reasons for that decision are outlined, together with an account of the constraints and design requirements imposed by commencing by a vertical shaft in the hanging wall of the orebody.

Jan 1, 1982

By Y Mita, T Iwama, R Inoue, S Ueda

In the iron and steel manufacturing industries, efforts are being made to achieve carbon neutrality by 2050, and the transition from a coal-based steelmaking process to that utilising renewable energy is being pursued. An alternative process in which directly hydrogen-reduced iron is melted in an electric furnace is being investigated. It is known that foaming slag reduces heat loss from the steel bath in electric arc furnace, but iron loss due to the suspension of steel particles in the slag is indispensable. To improve the separation of steel particles from the slag, the control of the slag viscosity is important. Although the slag viscosity has been extensively studied, in those studies the slag was considered to be a simple liquid. However, in actual operations, slag is a multiphase fluid consisting of solid, gas and liquid phases. Therefore, in this study, by measuring the sedimentation velocity of titanium, stainless steel and glass spheres in an aqueous glycerin solution containing bubbles generated by the reaction between NaHCO3 and C2H2O4, the apparent viscosity of the gas-liquid fluid was evaluated based on Stoke’s law. It was found that the apparent viscosity of the gas-liquid fluid is larger than the viscosity of liquid phase and depends on both the bubble volume ratio in solution and the density of the falling solid sphere, and the apparent viscosity was different from that previously obtained by the rotation method. The apparent viscosity derived from the sedimentation velocity of solid spheres changed depending on the specific gravity of the ball. This is because the apparent viscosity is derived from the velocity of a ball falling in a static bubble in this method, whereas that is derived from the force applied by a stationary flow in the rotational method.

Aug 21, 2024

A thick sequence of alkaline intrusions and volcanic rocks underlies a Quaternary caldera on Liliir Island. The sequence is host to a still active sub-aerial hydrothermal system and associated epithermal gold mineralisation. Sub-horizontal alteration horizons exhibit progressively increasing chondrite norma-lised (La/Lu) en and (La/Sm) cn ratios from unaltered shoshonites, to the potassic alteration zone, to the argillic altera-tion zone to the advanced argillic alte-ration zone. The increasing fractionation of HEE, and especially of LHEE, up the alteration sequence is the result of de-creasing pH, temperature and alkalinity of the hydrothermal fluids with increa-sing alteration intensity. HRE3 were especially mobile in argillic and advanced argillic alteration units characterised by acid fluid conditions and large fluid volumes. Abundant Cl, S and CO2 within the hydrothermal fluids and thus abundant REE complexing agents and large fluid volumes favoured the mobility of REE during hydro-thermal alteration of the volcanic rocks and intrusions. Steam escape, mixing of the gases with groundwater and a change from a magmatic neutral chloride hydro-thermal system to a meteoric acid sulphate system was accompanied by liquid/vapour ratio changes, pronounced alkalinity, pH and temperature decreases, and fluid/rock ratio increases. This caused the mobili-sation, fractionation and deposition of PF.F.

Jan 1, 1990

By N Guresin, R Dunne, S Blanco

This paper presents the results of research work conducted to assess if aqueous solutions of sulfur dioxide (SO2) can be used to treat roaster calcine leach residues such that recovery of gold in this material can be achieved with subsequent application of the thiocyanate (SCN-) leaching system. The project is mainly aimed at assessing an alternative use for sulfur dioxide gas generated during flotation concentrate roasting. The calcine leach residue sample used in the study contained 2.56 g/t gold. The reason for this high level of residual gold is thought to be due to gold surface passivation by thin iron oxide films, presence of gold in solid solution with refractory iron oxides and encapsulation of gold in the structure of these iron oxides.The study was conducted in three stages. The first stage was the characterisation of a sample from a roaster calcine leach residue. The second stage in the project was a set of leaching tests to assess the feasibility of using aqueous solutions of sulfur dioxide to reductively dissolve refractory iron oxide mineral phases contained in the calcine. The final objective was to assess the efficiency of thiocyanate, a gold complexing ligand stable under acidic and oxidative conditions, to extract gold liberated during sulfur dioxide leaching.The study showed that the reductive sulfur dioxide treatment of the calcine leach residues followed by oxidative thiocyanate leaching to extract gold was not a particularly efficient process as only around 20 per cent gold could be extracted. Leaching the calcine residues by any of these systems separately also extracted the same amount of gold (12 - 14 per cent) implying that irrespective of the solution potential, the acidity helps dissolution of gold encapsulating minerals, mostly hematite, but at a very slow rate. The findings on the topic in the literature and during this study show the requirement for further technical investigations and economical analyses on two cases. The first case is to roast gold concentrates to produce magnetite rather than hematite followed by sulfur dioxide and thiocyanate leaching of magnetite containing calcines. The second case is to apply a magnetic concentration process to conventional roast-cyanidation calcine residues to produce a gold-rich magnetite concentrate that can be further treated with sulfur dioxide followed by thiocyanate leaching.For both cases, the best evaluation of the sulfur dioxide leach system in extracting residual gold from calcine leach residues will require a detailed economic analysis to find out the balance between the value of the gold recovered and the loss of revenue from acid production. There are a number of roasters that do not produce acid. In these cases, a portion of the unwanted sulfur dioxide gas can be used to recover gold in magnetite containing calcines as an economic incentive.CITATION:Guresin, N, Blanco, S and Dunne, R, 2013. Leaching roaster calcine leach residues with aqueous solutions of sulfur dioxide and thiocyanate, in Proceedings World Gold 2013 , pp 129-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Holcombe R. J, Dobos S. K, Little T. R

Blue amphibole-bearing rocks in the North D'aguilar Block of southeast Queensland occur either as relict pods and lenses within regionally extensive greenschist facies phyllites and schists or as blocks entrained in serpentinite-matrix melange. Epidote + crossite-bearing varieties predominate and formed under conditions consistent with underplating and high P:T metamorphism in a subduction-related tectonic environment. Neither lawsonite nor jadeite has been observed and metamorphic conditions are estimated at 380-4500C for pressures of 0.5-0.8 GPa. High P:T metamorphism occurred during the earliest stages of deformation and was superimposed upon protoliths of inferred Late Devonian - Early Carboniferous age, including mafic volcanics, tuffs and coarse volcaniclastic breccias as well as pelagic and henipelagic sediments, all of which have undergone varying degrees of over-printing to the greenschist facies. Greenschist facies metamorphism occurred during the second phase of deformation and was associated with the formation of mainly flat-lying or subhorizontal structures; it followed the cessation of subduction and occurred in response to either thermal relaxation during uplift or the imposition of regional heating induced by crustal thickening and/or synkinanatic granite emplacement. Uplift and cooling of the high P:T rocks was completed by 260-265 Ma and may have occurred in response to the same extensional processes which gave rise to the onset of rifting in the adjacent Esk Trough.

Jan 1, 1990

By W Ilahi

Underground metalliferous mining methods often result in the formation of vertical openings to facilitate the extraction of orebodies. These development and production techniques can result in the creation of vertical open voids, which include stopes, orepasses, ventilation raises and other excavations. There are risks associated with the use of mobile plant in the vicinity of these voids, especially during backfilling and when bunds are constructed at the edge of a stope or void. These voids can present unacceptable risks if not adequately managed.

May 5, 2022

By M P. Sandy, V Louchnikov, V Eremenko, M Orunesu, O Watson

"Surface support is a key component of most ground support systems which are applied as a means of reducing the risk of rockfall occurrence and maintaining serviceability of mine development. Surface support has two primary functions: distributing the applied load throughout the system by providing connection between rock bolts retaining smaller rocks that unravel between rock bolts.Confinement is also provided to the rock mass, which may increase its capacity to resist further degradation or loosening.Surface support has been routinely installed in most underground mines around the world for many years, yet the operators are still not always certain which type is best suited for deformable ground conditions. A number of factors need to be taken into consideration prior to selecting the type of surface support liner, such as its capacity, availability, practicality of installation, manual handling and loading conditions (static or dynamic) to ensure the system’s optimal performance in terms of safety and costs.This paper presents an overview of the surface support types currently used in underground mines in Australia. Shotcrete, weld mesh, high-tensile chainlink mesh, reinforced weld mesh and high energy absorption (HEA) mesh are discussed. A detailed description of each system is provided in terms of capacity, energy absorption, installation cycle and costs. The cost of each system has been normalised to the units of energy absorbed. The information presented in this paper can be used by underground operators as a reference guide when deciding on suitable surface support type for deformable ground conditions.CITATION:Louchnikov, V, Sandy, M P, Watson, O, Orunesu, M and Eremenko, V, 2014. An overview of surface rock support for deformable ground conditions, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 57–66 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By J Say, M Hawtin, L Carlon, P Cann

Historically, production from sublevels of the Ernest Henry Mine (EHM) started from blind uphole rises at the end of slot drives. Where previous investigations considered removing these slot drives and starting production with independent ore drives, any development savings were consumed when drives were extended to minimise ore loss. Since 2017, EHM and Orica have been investigating opportunities to optimise drill and blast practices by implementing Orica’s Wireless Electronic Blasting System (WEBS). To reduce ore drive development metres, a novel design was proposed utilising the WebGen™ 100 system to combine a rise with pre-charged widening firings. Initially these new rise and widening firings achieved results similar to previous EHM designs, achieving on average 81 per cent of design height and width. Due to poor performance of the fourth trial a significant re-design was required. Modifications included drill hole re-positioning, in-hole primer relocation and initiation delay adjustments. Since the re-design a step change in rise performance has been observed with rise and pre-charged widening shots averaging 95 per cent of design height and width. With rise and widening performance exceeding expectations, the removal of slot drives has allowed a substantial reduction in lateral development. Development savings of 165 m and 169 m from the RL1325 and RL1300 levels have been achieved. Primary draw and ore recovery has also increased due to the later addition of pre charged forward stripping rings. Level design changes have also significantly improved the mining cycle by allowing for a reduction in required ground support, improved secondary ventilation, a reduction of critical path development, simpler production scheduling and less wear and tear on machinery. Future mine level designs now incorporate key learnings and are proving beneficial to a variety of scenarios including changing orebody boundaries at depth.

Mar 15, 2021

By T D. H McGrath, R Byleveld, W P. Staunton, J J. Eksteen

"The Gold Technology Group at Curtin University through the AMIRA P420 series of projects has recently developed the integrated liberation leach model (ILLM) for optimisation of gold plants. The model encompasses recovery by both gravity (batch centrifugal concentrators or BCCs) and leach adsorption (CIP/CIL) circuits. The ILLM essentially combines the Group’s well-known standalone models (ie gravity and SIMCIL) to create a robust simulation package.The ILLM process model provides a tool for sites to determine optimum set points for operations to optimise recovery (eg target grind size). It can also be used to predict the effect on gravity recovery, leach recovery and overall recovery when changes are made to circuit design, either temporarily (eg a leach tank taken off-line for maintenance) or as part of a circuit expansion (eg expanded gravity circuit capacity, or addition of leach tank capacity).This paper discusses the capability of the ILLM process model by highlighting a recent case study. The paper also addresses the test work and plant data required as model inputs, as well as limitations and the application of the ILLM to greenfield projects.Citation:McGrath, T D H, Staunton, W P, Eksteen, J J and Byleveld, R, 2016. Application of an Integrated Liberation Leach Model for Process Optimisation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S C. Dominy, R C. A Minnitt

Determination of the sampling constant and liberation diameter are of importance when applying the Fundamental Sampling Error (FSE) equation to optimise sampling protocols. The method for the direct determination of the sampling constant is based on the æGy 50-pieceÆ experiment and variants thereof, which is generally known as the heterogeneity test. In the coarse gold environment, the heterogeneity test is prone to poor repeatability and bias due to the very heterogeneity that it aims to quantify. A key issue is the large sample mass that can be required in the coarse gold environment, which may reach 1 t or more. The heterogeneity test often provides an evaluation of the background gold grade heterogeneity, but understates that of the high-grade coarse-gold component. This is because the total mass of fragments is usually too small to represent the mineralisation. Despite this relatively well-known problem, heterogeneity tests are often undertaken on deposits where the presence of coarse gold is ignored, not fully realised or vastly understated. Sampling types and protocol designs are frequently based on poor quality data that do not match the characteristics of the orebody. For this style of mineralisation, an empirical approach to define ore characteristics is recommended.CITATION:Dominy, S C and Minnitt, R C A, 2012. Application of heterogeneity testing to coarse gold ores, in Proceedings Sampling 2012 , pp 143-160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By G Balog, T Ormerod, D Sidea

Carrapateena is a copper-gold sub level caving operation located in the Gawler Craton, South Australia. One of Australia’s largest undeveloped copper deposits, the project will be a 4.25 Mtpa underground operation, with an estimated mine life of 20 years (OZ Minerals, 2017). First concentrate production was achieved in December 2019, within the Iron Ore Copper Gold (IOCG) hematite breccia complex. The Carrapateena orebody is overlain by 500 m of barren sediments of the Stuart Shelf, which hosts two aquifers. The cover sequence is dominated by shales, quartzites and sandstones in order of thickness. The cover sequence presented challenges to the mine ventilation system as a result of highly variable rock strengths. On this basis, the site developed the first vent rise, Vent Rise 5 (VR5), earlier than required as a means to test the empirical stability assessment. Assessment for VR5 was completed in 2017, with the mine yet to develop through much of the cover sequence. Due to the geotechnical data available at the time, it was anticipated that break out would occur within the vent rise walls as a function of the low strength Woomera shales. VR5 was developed to 4.5 mᴓ in late 2018. The timing of the VR5 development enabled the site technical team to calibrate empirical stability factors for the assessment of future vent rises. At the time of writing, four additional vent rises have been successfully developed to a diameter of 5.5 m. No significant overbreak has been observed within any of the vent rises. This paper is intended for geotechnical practitioners designing large-diameter vent rises in geological environments similar to the Stuart Shelf where a similar approach to vent rise design may be warranted.

Mar 15, 2021

By N Elith

The explosives demolition of a post-stressed, steel reinforced, concrete road bridge in Australia’s capital city, Canberra. The bridge was 50 m from the new replacement bridge, 320 m from community structures and within five kilometres of the national parliament buildings. The job required multiple overlays of risk assessment, public relations, safe work procedures, specialised blast design, environmental predictions and flyrock controls. Project stakeholders included Worksafe, Roads ACT, bridge owners, consulting structural engineers, community groups and road users. The bridge precincts, including a major road underneath, had to remain operational to peak traffic in the days leading up to the demolition. The break-up and removal of debris had to be executed in just two days from Friday to have the road beneath re-opened for Monday morning city-bound traffic.In Canberra, all explosives demolitions are now viewed with particular caution after a demolition in 1997, during which a young girl was killed. Any approval requires that Explosives Regulations, AS2187 2006 and Worksafe processes are satisfied, and a convincing case presented for blasting as a safe and viable option.Our design used specialised shaped cutting and blasting charges to sever in situ concrete beams and tendons and to shatter components of the stressed concrete bridge assembly. We include comments on structural engineering reports dealing with pre-weakening mechanisms. The benefit of pre-weakening is that it reduces the amount of explosives needed to safely complete the job and facilitates quick removal of debris after the shot. The complementary skills of the team, each one an expert in his field, resulted in a highly successful demolition, praised by authorities as an outstanding example of controlled use of explosives.

Nov 8, 2011

By A T. Spathis, M L. Lawlor-O’Neill

A methodology for the inversion of a scaled charge weight superposition model to predict peak particle velocity (PPV) has been examined. The inversion involves two steps: first simulated annealing is used to get an initial estimate of the model parameters; and second, these parameters are used as input to a quasi-Newton non-linear optimisation method, used to refine the value of the parameters. The methodology recovers the three required parameters (two charge weight scaling parameters and a time window width) and does this directly from a single production blast for a given point of interest. It has been tested on a synthetic example and recovered the input model parameters successfully in the presence of introduced noise with a coefficient of variation ranging up to ten per cent. Another test used the vibration measurements of three tunnel blasts monitored during the construction of the Citybanan tunnel in Stockholm. In this case, the three model parameters are found from one blast and for a given point of interest, and the PPV at the same point of interest is predicted for the second and third blast fired in the same vicinity as the first blast. The three blasts used different firing sequences. The predicted PPV limits use a confidence interval determined from the scatter in the peak levels obtained from the single calibration blast. The methodology was able to predict an upper bound for the PPV in 21 of the 26 tunnel blast vibrations studied. These predictions improve on a previous study involving the same model but which did not use the inversion process above. Given this reasonable success, further testing of the method on other data sets and alternative forward prediction models is recommended.CITATION:Lawlor-O’Neill, M L and Spathis, A T, 2015. An inversion method for the prediction of peak particle velocity in blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 97–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Hawkins

The Clem Jones Tunnel (formally known as the North-South Bypass Tunnel), a A$2.88 billion road tunnel project in Brisbane, Queensland, was successfully completed almost seven months ahead of schedule. The project included two parallel 4.7 km long road tunnels, 740 m of intermediate roadway access ramps and two auxiliary ventilation tunnels. The tunnels incorporate intelligent tunnel systems, best practice fire and life safety standards and typical civil tunnel elements.Over the duration of the project the Parsons Brinckerhoff (PB) and AECOM (formally Maunsell) design joint venture (MPB) were Lead Designers to the Leighton Contractors and Baulderstone Bilfinger Berger Joint Venture (LBBJV). Construction of the toll road commenced in September 2006 and was completed in March 2010, with the tunnel opening then. Contributing to the success of this project was the continued support the lead designers gave throughout the construction period.This paper will focus on some of the structural elements that contributed to the success of the project – in particular the cable tunnel structure, a small precast, culvert shaped element under the pavement of the mainline tunnel, and the fit-out of the Gibbon Street shaft which were designed to be constructed in a combination of precast and in situ concrete.The cable tunnel was incorporated early in the design phase and runs the length of much of the tunnel. This paper will outline the challenges faced by the designers with implementing this system which provided significant construction advantages, among which were being able to install a separate ventilation duct during construction and to start fitting out the mechanical and electrical conduits and drainage system while tunnelling was still underway.The Gibbon Street shaft had a length and width of 20 m by 40 m and an overall depth of 38 m. A 20 m high structure of precast and in situ concrete was constructed in the base to accommodate mechanical and electrical equipment and provide a take-off access for the southern ventilation tunnel. The construction purpose for this structure was to provide a junction between the tunnel boring machine (TBM) and the roadheader-style tunnels, a staging platform for commencing the roadheader tunnelling, and a platform where the TBMs could be dismantled and removed.The design was assessed and reviewed many times throughout the construction process to address the needs of each of these stages. Innovative use of precast concrete was used to minimise construction time.Additionally, the designers provided support to the construction team from the time of design completion through to the tunnel opening. This meant that the changes to the design and adjustment of construction loadings could also be assessed. The fi nal outcome resulted in an efficient construction sequence and a project that has provided an excellent outcome for the client, stakeholders and community.

Mar 8, 2011

By S Serp, M Duchateau, P Chevreux

Molten salt reactor (MSR) is a promising advanced reactor system aiming to the transmutation of minor actinides such as americium in order to reduce the inventory of ultimate nuclear waste. The fuel is a molten salt in which actinides are homogeneously dissolved in the liquid phase. A chloride salt may be retained for this concept, as it provides low melting point, high solubility of actinides, harder neutron spectrum. To avoid corrosion and precipitation issues, molten salt composition has to be carefully controlled with impurity content as low as possible. Obtaining pure actinide chlorides without contaminants such as oxide, oxychloride, hydroxide and water is still a challenge. To prepare actinide-bearing salt, the chlorination of actinides oxides was investigated in an unstirred reactor under flowing gas as solid-gas reaction. The carbochlorination of PuO2 were performed in the temperature range of 600 to 800°C with chlorine gas as a chlorinating agent and the presence of solid carbon. PuCl3 was successfully synthesised by this method and characterised by X-ray diffraction measurements but some impurities such as oxide phase remain inside the formed product. Refinements of anhydrous and hydrated PuCl3 phases by Le Bail method were also performed for crystalline materials definition. Conversion mainly depends on the chlorinating temperature and the contact between the oxide and the chlorinating agent. A conversion value of 70–80 per cent was achieved at 700°C from PuO2 with quite high specific surface area. The conversion rate was not improved with increasing the chlorination time. The volatilisation of Pu was observed during the carbochlorination experiments. To avoid a loss of Pu caused by sublimation, the chlorination temperature should be limited to 650°C despite that the conversion of PuO2 to PuCl3 was enhanced by increasing temperature. Both carbochlorination and hydrochlorination of AmO2 were also carried out leading to the formation of AmCl3. These first results suggest that americium oxide was chlorinated more readily than plutonium oxide. The purity of produced PuCl3 and AmCl3 still deserves further investigations.

Jun 19, 2024

By C Tapia Cortez, A G. Dempster, R Fradet, S Saydam, T de Roche, R Shishko, J Coulton

Human ventures into space are entering a new phase in which missions formerly driven by government agencies are now being replaced by those led by commercial enterprises – in launch, satellite deployment, resupply of the International Space Station and space tourism. In the not-too-distant future, commercial opportunities will also include the mining of asteroids, comets, the Moon and Mars. This research examines the role of off-Earth mining in a growing space economy. In this investigation, the term ‘mining’ is taken to embrace minerals, ice/water and other in situ resources. As the off-Earth mining initiative could be the engine that drives the space economy, it would be useful to understand what off-Earth mining market conditions and technology requirements are needed for that economy to prosper. These specific elements are studied in the wider context of creating an economy that could ultimately support a sustainable Mars colony. The methodology for developing the model focuses on the extraction of ice from the surface of Mars to produce propellant and water for life support for a possible colony.CITATION:Saydam, S, Shishko, R, Tapia Cortez, C, de Roche, T, Fradet, R, Coulton, J and Dempster, A G, 2015. An integrated economics model for in situ resource utilisation in support of a Mars colony, in Proceedings Third International Future Mining Conference, pp 305–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015