Search Documents

By K Luthbom, A Lagerkvist

According to the Swedish Environmental Protection Agency, the number of potentially contaminated sites in Sweden is approximately 40 000. The funding for remediation from the Swedish Government alone amounts to $A 60 - 80 M (300 - 400 MSEK) annually for the period 2003 - 2006. Uncertainties will arise when obtaining samples in field, preparing them in laboratories and analysing them. Different procedures give rise to varying errors. Using data for decision-making that does not truly represent the site could be fatal. Misclassification of soil could lead to unnecessary costs or to risks to human health and the environment. The total uncertainty of an environmental sample can be split into analytical uncertainty and sampling uncertainty. The analytical uncertainty is usually known and reported from routine analysis. The size of the sampling uncertainty is less well known. Hence, the question is how big are the sampling uncertainties for contaminated soil and how big is the analytical error compared to the total sampling error? A scrap yard and two landfills within a workshop area were investigated. An excavator dug trial pits and samples were taken with a trowel from the walls of the trial pits. Samples were put into plastic bags and taken off site for preparation and analysis using XRF. Sample preparation included drying and sieving. The samples were homogenised by kneading the sample bags prior to analysis. The sampling and sample handling were performed in an intuitively way without knowledge of sampling theory. However, Pierre GyÆs sampling theory was used for subsequent evaluation of the data from the site investigation. The theory defines seven sampling errors, which can be applied to sampling of soil. Some errors have a variance that can be calculated or at least estimated, while other errors can give some idea whether the bias is positive or negative. The total sampling error varied over three orders of magnitudes from sample to sample. The single largest contributor to the large variation in error was the contaminant level. When comparing the analytical error and the total sampling error the ratio varies more than three orders of magnitude.

Jan 1, 2005

By C Laming, P M. Hetherington, F A. Pym, M P. Murphy, K E. Crook

Reconciliation is a powerful tool used by mining operations to compare the mass and grade of ore produced with what was estimated before mining. The primary objective of reconciliation is to verify that the estimated planned metal production is achieved during processing, allowing issues to be identified for which adjustments can be made throughout the mining value chain to improve recovery and maximise efficiency. Traditionally, the mine plan is based on estimated mine grades using sampled exploration drill hole or blasthole grades. Reconciliation discrepancies between the mine plan and mill are common due to such factors as insufficient or non-representative sampling, poorly conceived models, or unrecognised blast movement. MineSense Technologies Limited® (MTL) has developed an X-ray fluorescence (XRF) sensor-based ore classification system that is installed on mining equipment to provide real-time grade estimates of run-of-mine material at bucket, truck, or belt-scale. Bucket level grade estimates provide insights into grade variations at the mine face that were never before available. This data set eliminates some of the leading causes of reconciliation discrepancies and enables tracking of tonnages and grades from the mine face to the processing plant at bucket resolution with confidence. Bucket-by-bucket grades at the mine face enable dynamic optimisation of the mine plan to stabilise the mill feed grade through blending of mine and stockpile loads. Beyond stabilising feed grade, Mine to Mill reconciliation combined with the full XRF spectrum response can generate proxy relationships to ore characteristics like hardness and recovery. These properties can then be predicted at the mine face, enabling further optimisation of the downstream mill feed, not only for grade, but also for power and water consumption, reagent addition, and recovery. This paper presents the benefits of MTL technology for grade reconciliation and mill performance optimisation at a Cu Mine in BC (Canada).

Mar 22, 2022

By L Soares, W T. Hennies, F Fujimura

The engineering geological mapping of Metropolitan Area of Jopo Pessoa in the littoral zone of the Parafba State, northeast of Brazil, made possible the ambient characterisation for space using and its implications on the environmental resources. This region comes lately denoting an accented industrial growth and this work would help future projects of urban planning, distinguished by quick ground occupations for residential, industrial installations, farming, beyond mineral extractions. The mineral sector supplies material and substance demanded by industry and civil constructions, like as clay deposits, sands, calcareous rocks and mineral water. Many companies working there do not have the permission or inspection of ambient agencies for planned extractions of mineral resources. The consequences of this activity pass for the low profit of the reserves, bad uses of the sources, ground degradation, vegetation suppressions and physical impacts on landscapes, beyond noises and vibrations. These activities have causing accelerated alterations and transformations in the environment, compromising the sustainable development. It thus becomes clear that urgent solutions must be find to solve the problems with human interferences by closer inspection and management for disciplined use of its natural resources.

Jan 1, 2003

By C Preston, T Williams, D Roy

The easiest way to mine valuable orebodies is through the use of explosives and well-planned blasting layouts that produce fragmentation profiles designed specifically for conveyance equipment in underground mines. The design of blasting patterns is specific to not only the explosives being used but also the rock or ore type being fragmented. Many blasting designs are based solely on the experience of those developed for similar orebodies in terms of properties and orientation or individuals that have some blasting experience.The primary technical objective of this paper is to outline a unique methodology for determining underground blasting methodologies (developing specific blasting parameters) commensurate with explosive energies and rock/ore equations of state for a narrow-vein gold property located in Northern Quebec and for underground mines in general.The procedures developed are to define the desired fragmentation specification so that a specific thermodynamic break is generated, taking into account powder factor, energy factor, tonnages, explosive energies and distribution along with blasthole diameter and orebody orientation for a specific set of explosive and dynamic rock/ore properties. Determining dynamic modulus values for the ore using seismic sensors to measure P- and S-wave velocities, the aforementioned parameters will be utilised to set the design constraints to maximise recovery and minimise overbreak and dilution.New underground blasting software (AEGIS) will use thermodynamic break in conjunction with defined fragmentation profiles to create an array of blasting parameters used to design and plan ring layouts. This software will also allow mining planners, prior to drilling and loading a production blast, to appraise future intended blasting patterns to minimise the potential of diluting ore with host rock and the likelihood of damaging mine support structures.CITATION:Roy, D, Williams, T and Preston, C, 2015. Underground stope drill and blast designs optimisation program, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 137–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Lechner, T Baumgartl, S Arnold, P Audet

When revegetation is a part of a rehabilitation strategy at mine sites in arid and semi-arid environments, its success can be strongly affected by the availability of water prior or during the time of seed dormancy, germination and early growth of seedlings. The semi-arid and arid environments of northern Australia are characterised by highly variable and erratic rainfall and hence the actual weather conditions at and around the time of germination and seedling emergence play a critical role in determining the success of plant establishment and the type of plant community that may develop.Using available climate data, an analysis has been undertaken and a set of indices has been developed which describe the suitability of the climatic conditions for rehabilitation. In total, eight sites from Queensland and one site from New South Wales, Australia have been analysed. It could be determined that regular rainfall and relatively short periods of water-deficit are key characteristics of climate suitability. A comparison of the locations studied allowed the separation into suitable and susceptible locations in terms of the availability of water, amount of rain and duration of drought between rain events.In our experience, specific estimates of climate suitability are rarely incorporated into the design of mined land rehabilitation programs. We consider that the regional intensity, seasonality and extremity of climate represent an overarching component of landscape complexity, which in turn will influence the development of post-disturbance ecosystems in these regions. This paper presents the outcome of climate analyses paired with the development of suitability indices. A conceptual framework is presented explaining the suitability matrix and its incorporation as a prognosis tool to achieve greater certainty for success in rehabilitation development.CITATION:Baumgartl, T, Arnold, S, Audet, P and Lechner, A, 2014. Development of climate-based suitability indices for the improvement of success in rehabilitation, in Proceedings Life-of-Mine 2014 , pp 483–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Reifenstein A

ACIRL's petrographers apply microscopic techniques to coal exploration, production, preparation and processing problems and research investigations as well as provide a commercial service for quality control of export coal shipments. This paper describes a number of case studies of applications of petrography to coal industry problems and coal research, including

Jan 1, 1989

By Zhou Y, Karmis M, Haycocks C

Hazard analysis utilizes interaction mecha- nisms in combination with geologic, structural and mining conditions to delineate areas of potential damage in seams subject to interaction. Using characterizations of conditions peculiar to multi- seam mining, such as innerburden thickness, geol- ogy and structures, initial interaction contour maps can be constructed. Geologic hazard analysis is then carried out on roof, pillar and floor condi- tions in the affected seam using lower seam rock properties and layout geometries in the overlying seam. Either safety factors or damage ratings can then be developed representing degree of hazard in the lower seam. The final hazard map shows both the aerial extent and magnitude of potential dam- age from interaction.

Jan 1, 1992

Mid-ocean ridges host approximately 65 per cent of about 100 known sites of high-temperature venting and polymetallic sulfide deposits; most of them are located at the East Pacific Rise (EPR), while more diverse mineralisation styles occur at the Mid-Atlantic Rise (MAR). Seafloor hydrothermal activity at the EPR are related to MORB while different substrates, including MORB and ultramafic intrusive rocks, are associated with æblack smokersÆ at the MAR. Depth of hydrothermal activity ranges from 0.7 to 4.3 km. High-temperature vents precipitating Cu-Fe sulfides (chalcopyrite and isocubanite, rare bornite), pyrrhotite, pyrite (¦ marcasite), and sphalerite, and low-temperature edifices precipitating marcasite (with pyrite), sphalerite, barite, andsubordinate chalcopyrite (pyrrhotite and isocubanite are absent) occur in both environments. There are considerable differences in Fe, Zn, Cu, Ag, Au and trace element contents in ores and in theFeS contents in Zn-sulfides in these deposits. Acomparison with anhydrite and sulfide minerals precipitating from modern black smoker fluids sulfide reveals many similarities but also some important differences. Fluids with salinity values above and below that of seawater at 400¦C down to 130 - 170¦C deposited sulfide minerals. Mantle-derived He prevails in fluids trapped by sulfides in EPR 9¦N and 21¦N hydrothermal systems. Hydrothermal fluids in MAR and back-arc systems are richer in radiogenic 4He. The sulfur isotope composition varies in the different hydrothermal fields and within zones of a chimney. EPR sulfides display narrower range of d34S values, while MAR and back-arc sulfides can bedepleted and enriched in the heavier d34S isotope. The most important finding is that fluid temperature, salinity, R/Ra ratios and d34S values ranged more significantly in the polymetallic sulfide deposits than when measured directly on venting fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By A Domanti, C Jewkes

This paper describes the design and constructability issues investigated in the selection of a trenchless solution in comparison to trenched construction options as part of a scoping study for the augmentation of the existing Bulimba Creek Trunk Sewer in Brisbane. Initial work involved the planning of alignment options vis-a-vis ground geology, geotechnical conditions, location and depth of shafts considering potential construction technology, flotation and stability of the tunnel, availability of construction sites and the influence of construction works on neighbourhood properties and the immediate environment. Two design pipe sizes, DN1200 and DN1500, were considered, and factors including jacking forces, specification of product pipes, pipe joints, pipe jacking methods and the associated impacts of ground settlement were carried out. Of particular interest was research on suitable lubricating fluids with the potential to minimise jacking forces and maximise the length of pipeline between launch and reception shafts.

Jan 1, 2008

A static equilibrium mathematical model of the lead,flotation circuit at The Zinc Corporation Limited is developed to permit the feasibility of applying computer control techniques to be studied. The model is based on the relationship between the cumulative recovery of a mineral species R from n flotation cells or assemblies in a unit given asR = M(1-(1 - p)?)where M is the maximum possible: recovery and p is the probability of flotation for the particular mineral.The verification of this relationship by data from pilot plant cell-to-cell and plant open flow flotation units shows that these systems behave as if the probability p is constant for each cell or assembly of anyone unit. It is also concluded from this study that mineral recovery is independent of the head assay. Two consequences of this probability relationship, are demonstrated.1. The total recovery from an open flow unit is enhanced by increasing the number of flotation assemblies but maintaining a constant flotation time and total air addition.2. The rougher and scavenger capacity required to recover a bulk lead-zinc concentrate is approximately half that used for selective flotation.The static equilibrium model is derived by solving a series, of mass balance equations which incorporate the recovery-probability relationship for each type of flotation unit. It is used to calculate the complete metallurgy of the circuit for any arrangement of cells knowing only the plant feed assays and the probabilities of flotation for the three mineral types, galena, marmatite, and gangue for rougher, scavenger, and cleaner flotation. The high degree of prediction obtained is demonstrated by comparison with plant results.Pulp flowrate is the principal variable affecting the accuracy of the present model. Work is in progress to establish this effect and permit the derivation of a dynamic model. Even so, the static model is valuable in its present form for the analysis and design of circuits, and optimisation studies using computer services have been conducted.

Jan 1, 1964

By J King, T Hunter, R Coleman

"The industry that supports operations and new projects is suffering a rapid decline in the currently severely curtailed capital investment environment. This is evidenced by a decline in the number of skilled teams, who are now centred in fewer locations. Other features are an aging and retiring ‘Baby Boomer’ generation, coupled with a low uptake of new graduates and the uncertainty in predicting future capital expenditure programs and requirements. Combine this with a reluctance of cash-poor operations to modernise and adapt in an environment of low metal prices, and there is a real uncertainty in how service providers will meet industry needs as they evolve.The industry that supports operations and new projects is suffering a rapid decline in the currently severely curtailed capital investment environment. This is evidenced by a decline in the number of skilled teams, who are now centred in fewer locations. Other features are an aging and retiring ‘Baby Boomer’ generation, coupled with a low uptake of new graduates and the uncertainty in predicting future capital expenditure programs and requirements. Combine this with a reluctance of cash-poor operations to modernise and adapt in an environment of low metal prices, and there is a real uncertainty in how service providers will meet industry needs as they evolve.Trends amongst service providers will be put forward as well as developing options and alternatives. These embrace a whole gamut of agile alternatives in the areas of partnering, alliances, commercial and shared risk models and mutual innovations. These will be discussed with some case studies and suggested approaches.Particular emphasis will be upon brownfield expansions and upgrades which have emerged recently as a preferred lower capital and focused way to achieve best practical outcome at lowest cost. There are a number of specific features of such brownfields projects including the requirement for very close cooperation between the execution team, operators, maintenance and suppliers and a maximum usage of site resources and ingenuity. Often, required investment hurdle rates are high, downtime allowed is minimal and site resources usage is maximised. This requires mutual trust, good planning and high health, safety, environment and community (HSEC) standards and practice. In many ways the practices and skills needed are the exact opposite of the historical ‘big greenfields’ project with which the industry has been geared for more recently.Another developing area has been with innovative commercial models and practices. These have been as a direct result of the more challenging investment criteria being adopted and the relative hunger of service providers. It has become more common to look at these commercial/costing alternatives very early in the project cycle as an essential project tool and not just as a possible option. These commercial solutions cover such alternatives as leasing and rental, deferred payments, build–own–operate–transfer (BOOT) and build–own–operate (BOO), whole-of-mine preferred spares and maintenance terms, and aggressive performance targets with real assurance penalties. Once again this requires very close mutual dealings and trust, and sufficient time allocation compared to a conventional approach.Citation:Coleman, R, King, J and Hunter, T, 2016. Upgrades, Modernisations and Expansions... Where Will the Expertise, Capability and Skills Come from in the Future?, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D Corley, J Moore, M Grant, A, W R

Resource estimates are the corner stone of technical and investment decision-making. Prior to mining, resource estimation uncertainty has the greatest potential to lead to poor investment decisions, despite a significant component of resource estimation uncertainty being unknowable at this critical stage in the mining cycle. This presents a conundrum to the resource geologist in terms of risk evaluation and resource classification. Ahead of mining, there is normally considerable focus on drill hole spacing analysis to determine the ‘optimal’ drill hole spacing, taking grade and geological continuity into account; cost-benefit analyses balance improved resource definition against cost; the law of diminishing returns and the exponential cost increases acting together as spacing is reduced. Typically, a lower limit to the drill hole spacing is identified. After completing the resource drilling to an agreed spacing, resource estimation is then undertaken. At this point it is common to attempt to bracket the resource estimation uncertainty. In many cases conditional simulation is used, based on a modelled, but largely assumed, variogram model. It is also assumed that the histogram of the available drill hole sample data is representative of the in-ground mineralisation. The purpose of this paper is not to diminish the importance of drill hole spacing and simulation studies, but rather to illuminate an important aspect of estimation uncertainty that, although previously recognised, is typically overlooked – the question of how representative the available data set is in characterising the true (but unknown) distribution of mineralisation. To do this, we lift the lid on one of OceanaGold’s former operations, the mined-out Globe Progress Mine, by resurrecting a high quality, close-spaced, reverse circulation (RC) grade control data set. The Globe Progress Mine is within the West Coast Region of New Zealand, it was closed and transitioned to rehabilitation in 2016 and is now known as the Reefton Restoration Project. The exhaustive Globe Progress grade control data was used to repeatedly ‘redrill’ the deposit by extracting 35 m × 35 m spaced subsets from the original 5 m × 5 m spaced grade control data. Utilising closely spaced grade control data removed the need for assumptions regarding short range continuity, which are necessary with forward-looking analyses that are based upon broader spaced resource drilling. The extraction process used a nearest neighbourhood algorithm, repeatedly moving the origin in 5 mE, or 5 mN increments. Individual resource estimates were then completed for each of the extracted drill hole data sets (49 in total) as well as a grade control estimate based upon the exhaustive data set. Whilst the data unpinning each of the 49 estimates changed, the geological assumptions, variography, and modelling parameters remained constant. This approach was taken to isolate the impact of changing the input data. The 49 estimates were then compared against each other and the grade control estimate. The mean of all 49 sensitivity estimates was close to that of the grade control estimate in terms of contained gold, tonnes and grade. Whilst it is acknowledged that the grade control estimate itself is subject to some degree of estimation uncertainty, the close match between the average of the 49 estimates and the grade control estimate suggests that the resource estimation methodology is reasonable and appropriate. Whilst this comparison is important, the focus of this study is on the component of estimation uncertainty related to the underlying data, and this is reflected in the spread across the estimates. The spread across the 49 global estimates (highest to lowest) for this particular Mineral Resource Estimation Conference 2023 | Perth, Australia | 24–25 May 2023 142 case study was found to be significant (approximately 20 per cent in grade and metal) and that is attributable solely to the underlying data. This exercise quantifies a component of the estimation uncertainty that is inherent to all drill hole data and is distinct from the uncertainties associated with modelling methodology choices, sample and subsample quality and drill hole spacing-related interpolation uncertainty. Importantly, this uncertainty is unknowable prior to mining; we can only directly compare the resource drill hole data against grade control data after mining has taken place. For the case study, approximately 65 per cent of the estimates fell within 5 per cent of the grade control estimate for contained-gold, suggesting that for many projects the histogram of drill hole data is unlikely to differ noticeably from that of the in-ground resource. However, about 15 per cent of the estimates in this study differed by more than 7.5 per cent, suggesting that a not-insignificant proportion of estimates will be materially compromised. Whether or not the available drill hole data is representative comes down to the ‘luck of the draw’ and cannot be known at the time of resource estimation. Given the challenge of attempting to evaluate forward-looking estimation uncertainty, a component of which that can only be quantified retrospectively, what should we do as resource geologists? What are the implications for risk evaluation, resource classification and reconciliation? Furthermore, without rigorous post-mining data checks, resource geologists may conflate suboptimal modelling with the shortcomings of the underlying data. An example of this problem is discussed in the following section.

May 24, 2023

By R Williams, P Godwin

In a time of changing rainfall patterns and in the light of recent tailings dam failures, there is closer environmental scrutiny for proposed tailings dam construction or expansion. Therefore the elimination of the traditional tailings dam could provide both environmental and cost benefits to an operation. One method to dewater tails is using pressure filtration to achieve lower moistures than what is currently available using other dewatering technologies. Further benefits include a higher rate of filtrate recovery, reuse of waste material and the potential for dry stacking of the filtered tailings cake, thereby minimising both risk and cost. This paper chronicles the replacement of two existing belt filter presses with a single McLanahan recessed plate filter press to dewater a tailings stream at a Bacchus Marsh site. It covers the slurry testing, equipment selection, installation, commissioning and operation of the filter press to achieve the following objectives:• removing the current tailings dam and slimes cells from the existing process to minimise failure risk and reduce the cost of a dam upgrade, as well as operational and maintenance costs• free up the surface area which was previously occupied by tailings dams and slimes cells• recover additional water to be returned to the process• reduce flocculent usage• reduce truck movements and handling.The project’s owner also expects to reduce carbon emissions by over 3000 t over the lifetime of operation as well as substantially reducing operating expenditure. By recognising the carbon reduction benefits, the project owner was able to successfully achieve partial funding through the Voluntary Waste Industry Protocol.An unanticipated, but as yet unquantifiable, bonus for the project was to seek an offtake agreement for the tailings thereby allowing the tailings to be considered a valuable source of beneficiated clay suitable for the construction industry.CITATION:Godwin, P and Williams, R, 2017. Pressure filtered tailings – environmental and cost benefits, in Proceedings MetPlant 2017, pp 324–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By H Rouhullahi, E B. Veshki an, R Kottnauer

The Galandrud coalfield is located approximately 20 km south from the coast of the Caspian Sea, Ruyan town, on the north slopes of the Alborz mountain range, in the elevation between 500 m (the Galand River valley) and 1350 m. For the time being, 32 coal seams (generally of small thickness û 0.8 m on average) have been recognised within the. On the other hand 72 coal banks of balanced properties have been included in reserve calculation, which means that some of the seams consist of several banks. The general dip of strata belonging to the south limb is about 30¦ to the South (with drags close to the south overthrust, where the dip reaches 85¦), while the dip of beds at the north limb is rather steep and usually between 45 to 75¦ to the North. The coal quality is in a rank of high volatile bituminous coal. The steep dip, unstable lithological development, complicated tectonics and comparatively lower coal seam thickness are the characteristic features of the Galandrud deposit. Environmental protection of this area makes exploration and exploitation more complicated. During mine exploration several adits were driven at three levels with 50 m vertical distances. About 4000 m of gates and crosscuts were up to now driven. During mining test the down-cut mining method (with one cut), the strike cut mining method and the down-cut mining method with two cuts were tested. The paper describes outlines for the selection of mining methods on the base of classification of the effective hangingwalls and footwalls, hazards of mining operations, and possibilities of the mechanised mining.

Jan 1, 2003

White Cliffs Opal Field is situated in the Parish of Kirk, County of YulguIgra, New South Wales, about sixty miles from Wilcannia, and the River Darling. It is near the southern edge of the cretaceous basin of the interior of Queensland, New South Wales, and South Australia. Twelve miles south-west of the field, at Tarella station, a well sunk at the homestead reached silurian slates at about 127 feet, getting no water but about three miles north-west from the originally discovered and no central portion of the field, a well was sunk by the Momba, Pastoral cmpany, to a depth of 270 feet all the way through the cretaceous beds. At 250 feet a small supply of water was struck, but so much mineralised as to be quite useless. The temperature also was so high that a man could not keep his hand in it and Mr. Hogarth, the Momba Pastoral Company's manager, informs me that so corrosive was the action of the water, that a shovel left down the well for a fortnight, at the time of sinking, was completely eaten away.The well having now fallen in, I have been unable to obtain any of the water for analysis.The western termination of this portion of the cretaceous basin is situated about twenty miles from the present opal field, at which distance the slates, with (probably) devonian sandstones and quartzites resting unconformably thereon, commence to appear. The opal bearing country, as far as at present known, follows a more or less well defined line running north and south towards the northern end of the field, and north-east and south-west towards the southern extremity.

By N S. Weerasekara, S Town, E Lessing, J A. De Torres

Philsaga Mining Corporation (Philsaga) had three main aims in converting their lining system from steel to metal cap. They wanted to increase mill availability, minimise localised high wear and optimise particle breakage to deliver increased efficiency within the milling circuit. Combining Discrete Element Method (DEM) modelling and empirical interpretation of liner wear resulted in a rigorous approach to understanding the impact of mill liners on overall mill performance. This new understanding was subsequently used to not only derive a new lining design to optimise performance and thereby improve overall plant economics, but also to guide further lining development.In this work, detailed DEM modelling, developed from actual plant data, together with optimising liner design for wear paved the way towards the installation of a Metal Cap lining system at Philsaga’s Ø6100 mm SAG Mill. The results were a reported increase in SAG mill throughput of 16 – 20 per cent due to improved breakage through more efficient use of installed power, a reduction in localised high liner wear with overall increase in liner life and reduction in liner replacement time. Site also reported an increased gold recovery of 2 per cent which the improved breakage might have contributed to. This paper will present the design challenges and compare the Metal Cap lining systems performance against Steel lining system. CITATION:Weerasekara, N S, Lessing, E, Town, S and De Torres, J A, 2018. Metal cap versus steel lining system at Philsaga Mining Corporation’s Ø6100 mm SAG mill, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 653–664 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Mimura K

The carbon reduction of tantalum pentoxide was investigated in a plasma-arc furnace. The sample was a mixture of tantalum pentoxide and graphite, vacuum pressed into a briquette and was reduced at about 3100¦C. Argon was used as the are gas. The optimum mixing ratio of carbon and tantalum pentoxide, C/Ta205 is 5.10--5.15. The sample, weighing 7 g is fused within 60^ 70 seconds by plasma-arc heating and the reduction of molten tantalum oxide with solid carbon pro- ceeds rapidly to approximately 99.5 % Ta during this period. The reduction that follows in the molten state is slow. Within about 10 minutes, the maximum tantalum content of the massive metal product reaches 99.9 % and the oxygen and carbon remaining in the product are 50 ppm and 400. 500 ppm respectively.

Jan 1, 1980

By Zhijing Z, Huiling Z

The influences on flotabilities of dolomite and magnesite with modifiers and influences on the function of collectors and modifiers with Mg+z Ca+2 were studied. The flotation results of artificial mixed mineral showed that using combined salified water glass and (NaPO3)6 as a modifier for magnesite-dolomite separation can obtain an excellent Selectivity.

Jan 1, 1993

By J Seppelt, G S. Lane, E Wang

Newcrest’s Cadia concentrator operated from 1998 to 2012 with a traditional SABC grinding circuit treating Cadia open pit ore. The Cadia comminution circuit was well characterised through surveys and data that are available in the public domain, and became a benchmark standard for the industry and practitioners modelling large SAG mill based circuits. In 2012, the HPGR-based crushing circuit was introduced in front of the SAG mill to increase throughput when treating the Cadia East ore that was derived from an underground block cave. This ore was expected to be more competent and have a coarser run-of-mine size distribution.Numerous previous papers have described the design and commissioning of the Cadia HPGR-based circuit.This paper describes the improvement in comminution energy consumption resulting from the introduction of the HPGR, including identifying the impact of process complexity and an increase in ancillary energy consumption for conveyors, screening, and crushing.CITATION:Lane, G S, Seppelt, J and Wang, E, 2018. Quantifying the energy efficiency transformation at Cadia due to HPGR crushing, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 141–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By K J ROSENGREN

Underground rock mechanics was initiated as a formal discipline in Australia by early studies for underground structures for the Snowy Mountains Scheme in the 1950s. These techniques were quickly embraced by underground mining and there has been steady development to the present time. The paper reviews the status of current techniques for rock mechanics studies and discusses some important issues such as ground support, mine filling and caving. It concludes that a considerable degree of engineering judgement is still required for the practical application of rock mechanics to underground mine design.

Jan 1, 1992