Search Documents

By Hiddlestone D. C

Effective exploration, testing and analysis is essential for good process design and optimisation of coal preparation plants. Coal processing relies on the sizing and washability characteristics of the particular coal to define the most cost effective design to meet the market requirements. Flowsheet development and equipment selection is dependent on the natural quality characteristics of the coal, its physical properties and the value of the final product in its market. The methodology of process selection and the key elements in design are discussed. Coal is consumed in two general markets: ò steaming coal - both domestic and export, and ò metallurgical coal. This paper discusses the typical economic analysis required to evaluate the potential for, and cost benefit of, providing the flexibility to switch coals between markets. A case study illustrates the methodology of process selection in a typical high value metallurgical coal.

Jan 1, 1997

By Rosenblatt M, Gilroy J. A C Cunningham C V B

Vaal Reefs Exploration and Mining Company Limited operates one of the largest producing gold mines in the world. The annual production of 76 tons of gold from 12 million tons of ore treated is obtained mainly from underground sources. Daily some 6.6 km of stope face is blasted and 41 tons of explosives is used to break the rock. The mine employs 45 000 men of whom 35 000 work underground. The company operates nine large vertical shaft systems of which seven extend more than 2000 m below surface and an eighth, currently being sunk, will bottom at 3700 m below surface.

Jan 1, 1995

By Hanes J

More than 200 bursts in coal occurred at Leichhardt Colliery prior to December 1978 during mine development in the 6 m thick Gemini seam at depths approximating 400 m. Three large bursts each displaced more than 300 tonnes of coal and stone. Two of these which occurred in continuous miner developments, are described and compared. Geological settings, mining strains including induced cleavage and roof failures associated with bursts are described. A shotfiring technique replaced mechanised mining following a major incident at the colliery. Present mining procedures, the apparent improvement in stability of workings and ongoing geotechnical monitoring programme are discussed.

Jan 1, 1980

By Freeman NV

The concept of an in stream analysis probe was developed at The Zinc Corporation (now Z.C. Mines) in the late 1960's and commercialised quite rapidly, by Phillips and then AMDEL, as an alternative to the established centralised systems (Courier, etc.). The developments which have taken place since that time are reviewed and current procedures and performance are described. An audit of the system, recently undertaken by AMDEL, has highlighted areas where improvements can be made. In 1988 the ISA system will become an integral part of a substantially upgraded process control system.

Jan 1, 1988

By A J. Moore

To control the airblast from blasting to regulatory limits at environmentally sensitive sites near the Collinsville Coal Mining Operations, it has been necessary for Thiess Mining to incorporate a wavefront reinforcement analysis model in the predictive environmental airblast design. Controlling airblast from cast blasting 70 m high faces with 2000-3000 kg of explosives per hole within 700 m of houses presents a considerable challenge to the blasting personnel. This paper describes the model used and summarises the results of an investigation designed to quantify the increase in airblast indicated by wavefront reinforcement diagrams to further calibrate the model for future prediction.

Jan 1, 2004

By Singer RP

The Latrobe Valley brown coal deposits are one of Australia's major energy resources with measured and indicated reserves amounting to some 162 billion tonnes. Economically recoverable reserves are estimated at some 65 billion tonnes, 47 billion tonnes of which are classified as available for mining (VBCC (1983)). These deposits contain one of the lowest grade fuels used anywhere in the world. Typical Net Wet Specific Energy values range from 6 to 9 MJ/kg. Despite the low energy value of the raw coal, the Latrobe Valley deposits represent approximately 90% of Victoria's indigenous non-renewable energy resources. Utilisation of this vast primary energy resource has been a key factor in the economic development of Victoria.

Jan 1, 1990

By R G. Barker, A B. Christie

Minerals are necessary for providing almost everything we take for granted in our daily lives including food, shelter, and supplies of energy and water. Minerals are therefore essential for the maintenance and improvement of the standard of living of all New Zealanders.

Jan 1, 1998

In late 1987 it was recognised that column flotation might have potential for improving the grade of the zinc concentrate produced at Pasminco's South Mine in Broken Hill. Intermittent test work was carried out during 1988 using a 90 mm diameter by 6 m high perspex column, built and initially operated by staff from CRA Advanced Technical Development. This column was found to have insufficient retention time so, during the first half of 1989, Pasminco constructed and installed a 200 mm diameter unit of the same height. Extensive testwork was carried out using this column during the latter half of 1989 and early 1990. It was clear from the results that a grade improvement of between 1 and 2 per cent (absolute) would be achievable. The effect of column cleaning on overall recovery was not established with the same degree of confidence, so the proposed new circuit is to include one of the existing banks of OK8 cleaner cells as a scavenger on column tailings. The test work provided sufficient data for preliminary design work to begin in May 1990 and commissioning of full scale zinc cleaner columns is planned for mid 1991. This paper summarizes the results and describes some of the experiences with column flotation at the Pasminco South Mine.

Jan 1, 1991

By N J. Welham

The Intec Copper Process is an environmentally advantageous hydrometallurgical process for the production of high purity copper and associated precious metals from copper sulphide concentrates. The process uses a mixed chloride-bromide lixiviant in an elegant cyclic circuit to leach the copper into solution, rejecting the iron as stable hematite rather than as unstable jarosite. After purification of the pregnant liquor, copper is electrowon at London Metal Exchange Grade A purity, while the anodic energy of the cell is stored as the soluble species, HalexTM, for recycle as the regenerated lixiviant to the leach circuit. Both gold and silver are leached and recovered directly from this cyclic process without resorting to cyanide leaching of the residue. No liquid emissions result from the Intec Copper Process, whilst spent air and water vapour from the leach are released to the atmosphere. The sulphur in the minerals reports to the solids residue in elemental form, without the need for expensive handling of voluminous gaseous sulphur dioxide streams found in smelters. A significant difference to competing smelting and hydrometallurgical processes is that any mercury entering the process from the sulphide concentrate feed is recovered rather than reporting directly to waste or polluting the environment. Outside the process circuit itself, the Intec Copper Process has several notable environmental advantages over competing technologies: Flexibility of scale with low capital and operating costs allow operation directly at the mill head at production rates as low as 15 000 tpa, significantly reducing environmental impacts from concentrates transport. The ability to handle low-grade and dirty concentrates often allows greater recoveries in the mill, improving both the economics and environmental acceptability of a mine by reducing metal losses to tailings. A comparison of the total energy requirements of the Intec Copper Process with those of competing technologies shows that the Intec Copper Process has the lowest energy consumption of any of the known hydrometallurgical processes, as well as improving upon pyrometallurgy under appropriate conditions.

Jan 1, 2002

By Firmin K

The Mt. Tom Price orebody of Hamersley Iron Pty. Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the orebody, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control'of products based on selective mining is the production of advance data, on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades Are determined from assay of samples taken from blasthole cuttings.

Jan 1, 1980

Mine closure is a legitimate element of the mining cycle and like mine development involves technical planning, permitting, and finally construction. Closure begins with the mine's operational footprint and transforms the site so that it meets the explicit requirements of the owners and regulators. Implicitly, the closure will increasingly need to meet the requirements of other interested parties such as the local community, workforce, and future land users. Golden Cross is the first modern mine closure in New Zealand. It operated for 6 + years as a mid-size gold and silver mine winning ore from both underground and open pit sources, and processing via a carbon in leach circuit including a cyanide recovery stage prior to tailings disposal. The mine is situated in a sensitive high rainfall environment, and is complicated by the existence of a large ancient landslide underlying most of the tailings dam and waste rock embankment. The regulatory process for mine closure in New Zealand is not clearly understood by operators or regulators alike. The Golden Cross mine was permitted under the Mining Act 1971 and closed primarily under the Resource Management Act. This switch of legislation, the parallel reorganisation of many government departments, and change in societal expectations with respect to long term environmental stewardship during the life of the mine resulted in the requirements of closure being significantly different to the expectations at permitting.

Jan 1, 1999

By D G. Rantucci

Organic carbon is a major ore contaminant at MMG’s Century mine. This carbonaceous matter is associated with shale hosted sphalerite mineralisation. It occurs as elongated lamellae and as inclusions in porous sphalerite aggregates which are fine grained and difficult to liberate from sphalerite. The carbon prefloat circuit was designed to remove the liberated organic carbon in order to mitigate excessive reagent consumption, contamination of the lead and zinc concentrates and poor flotation performance in the primary zinc circuit. The consequence of organic carbon removal is that sphalerite and galena minerals are lost to the prefloat concentrate. A Jameson Cell was installed in late 2005 as a prefloat cleaner cell. Operational experience showed that the cell became capacity limited during periods of high amounts of organic carbon in the feed and was subsequently bypassed.Reactive style operating strategies were implemented to manage the effects of insufficient organic carbon removal by the prefloat circuit but due to the relatively large circuit residence time, upstream changes meant hours before the downstream circuits were stabilised following a disturbance from excess carbon.This paper describes the modifications and testwork undertaken to enable the Jameson Cell to be operated during periods of high organic carbon in the float feed and the implementation of process control initiatives to proactively remove the required prefloat mass from the float feed to eliminate the reactive style operating strategy.The process control modifications centred on dynamically targeting a prefloat mass recovery determined by an equation relating the carbon to zinc ratio to the carbon prefloat mass as a percentage of the float feed. The equation was developed by analysing historical data. These improvements served to optimise the prefloat circuit and consequently stabilise the downstream lead and zinc circuits.

Aug 8, 2011

By D Craw

Otago Schist and Klondike Schist are two Paleozoic-Mesozoic metamorphic belts on the circum-Pacific margin in which there has been a long history of abundant alluvial gold mining, but only minor hard-rock gold mining.   Modern exploration for hard-rock gold is ongoing in both belts, and the active Macraes mine in Otago (>2 Moz production) highlights the hard-rock potential of the geological setting of these belts. Hard-rock gold mineralisation in both belts formed in the latter stages of schist exhumation, after rocks were subjected to major regional ductile folding and then uplifted through the brittle-ductile transition. The majority of known hard-rock gold-bearing systems in both belts consist of well-defined, but generally discontinuous, vein swarms. Most Otago veins are hosted in steeply dipping post-metamorphic normal faults and fractures. However, the Macraes mine is hosted by a late-metamorphic shear zone, and much ore is sulphide-impregnated auriferous schist. Goldbearing veins in the Klondike schist are hosted primarily in extensional sites associated with post-metamorphic compressional structures. Some disseminated sulphide mineralisation is associated with Klondike veins and this is important as it extends the exploration target for these veins. No foliation-parallel late metamorphic mineralisation has been identified in the Klondike but exposure is relatively poor compared with Otago and both schist belts are highly prospective for deposits of this type.

Jan 1, 2007

By H Haghighi

Haul roads are often permanent unsealed access roads used by heavy haul trucks to transfer minerals. These roads can deteriorate rapidly which results in potholes, deformations and dust. Downer EDI Works has successfully provided efficient solutions to the mining industry to maintain their haul roads. HaulPac as a solution package is a process in which a bituminous emulsion is used to create a stable and durable pavement. The emulsion penetrates the road and binds the particles together, creating a stable base. It also seals the surface and prevents water from penetrating the underneath layers. Bituminous emulsion can increase the strength of the pavement material and decrease the road surface degradation which results in dust suppression. However, the everincreasing price of commodities, the necessity of reducing carbon emissions and the increasing use of autonomous haul trucks have made it vital to invest in novel maintenance solutions that can meet the needs of the mining industry in a cost-effective manner. This paper outlines the benefits of bituminous emulsion in terms of productivity, safety and environment followed by Downer’s approach to evaluate the suitability and to optimise the amount of product. The potential for changing the colour of the treated surface is explored and an initiative that incorporates end-of-life tyres of haul trucks into the pavement is introduced. And finally, an innovative method using artificial intelligence to estimate dust emission is presented.

Sep 18, 2023

By R Frew, E Wong, G Ferguson

The Chang Jiang Tunnel and Bridge Project, when completed, will provide a fixed link between ShanghaiÆs rapidly developing Pudong District and Chong Ming Island, situated in the Yangtze River delta. The link includes 7.5 km of bored tunnel from the Pudong to the intermediate Changxing Island from where the link comprises viaduct and a cable stayed bridge. The bored section comprises twin 13.7 m internal diameter segmentally lined three-lane highway tunnels. At its deepest point the tunnel will be 55 m below the river. Cross passages will link the two bores for passenger evacuation. Tunnel boring commenced in October 2006 and is scheduled for completion in mid-2009. The paper describes the key features of the design and construction of the bored tunnel by two 14.53 m diameter slurry TBMs and eight cross passages using ground freezing techniques in alluvial sediments. A decision to include light rail below the road deck was taken after the completion of the detailed design. This posed a number of design challenges including passenger evacuation to the road deck, and the redesign of the low point sumps. The various options considered are discussed together with those adopted for construction.

Jan 1, 2008

By Leung L, Downey M

This paper presents an overview of a technology package developed by BHP for locating discontinuities in coal seams using an in-seam seismic (ISS) exploration technique. The technology package includes instrumentation, data processing software, field procedures, numerical modelling and interpretation know-how. The technology developed has proved to be highly successful; features such as faults and dykes, not detected by other methods, have been delineated. Using equipment specifically designed for underground use, surveys are carried out quickly and at low cost. More than 30 ISS surveys have been conducted by BHP in Australia. Substantial savings in production revenue have been realised in situations where ISS has identified mining conditions which would have impeded longwall operations. Case studies of several ISS surveys are described in the Paper.

Jan 1, 1987

By Wright R. J

The Commission called tenders for a four boom hydraulic jumbo, plus basket, on an art- iculated carrier in Sept. 1977. Atlas Copco submitted the successful tender in Jan. 1978 for the supply of a three boom jumbo, plus basket. The Promec TH470 jumbo was commiss- ioned in the 2000 m long Sophia tunnel in Nov. 1978. Adequate spare parts were not available during the first three months of operation and the hammers could not be overhauled at the recommended interval. One hammer was removed after drilling 13 600 m due to a crack in the intermediate housing. Tests were conducted with different types of drilling consumables. Both rope and Hi-teed threads were tested and found compar- able. The average penetration rate in the granite was 1.1 m/min. Initially the drillers were not experienced enough to operate the BUT 15ERH booms without causing damage to the booms and hoses. Drilling deviation espec- ially of the perimeter holes was greater than expected. It is now obvious that greater attention must be given to attracting, train- ing and retaining the right type of operator and maintenance fitter.

Jan 1, 1981

High resolution seismic profiling has proved a cost effective tool for defining the structure and seam geometry of Late Cretaceous-Late Miocene age lignite deposits in the South Island of New Zealand since 1981.In 1985 a total of 45 km of Mini Sosie seismic reflection was carried out in the Benhar, Hawkdun and Ashers-Waituna deposits as part of a major multidisciplinary resource investigation funded by the Liquid Fuels Trust Board. For each deposit the seismic programme involved integrating four or more intersecting Mini Sosie traverses with a grid of 1000 m spaced geophysically logged drillholes. The objective was to detect faults, with displacements ranging 30 - 100 m, which might impede mining using bucket wheel excavator systems at depths down to 300 m below surface.In general the quality of processed seismic data was high and with the assistance of ynthetic seismograms and other geological information, it was possible to identify a number of significant previously unknown faults. The success of this seismic programme ha shown that high resolution seismic profiling, used in conjunction with relatively low density drilling, can produce valuable structural and tratigraphic information at an early stage of open pit mining investigation.

Jan 1, 1989

By Ramani R. V

In this paper, a comparative performance evaluation of geostatistical, spectral, and fractal methods is made for short-scale variability prediction. The algorithms compared are: sequential Gaussian simulation method; a random fractal algorithm based on the generalised stochastic subdivision method; and a spectral simulation approach adopted for direct multi-dimensional simulation. The data for this study have been obtained from a mined out coal property. As this property was being mined, a 7315 m by 7315 m (24000 ft by 24000 ft) coal block was extensively sampled at an approximate spacing of 107 m (350 ft) and the 60-ton samples were analysed for sulphur in the 1.50 float gravity fraction. This data set is used here with the three methods to generate the simulated realisations, which are analysed for semivariogram reproduction and for simulation errors. Although all three methods converge to the true semivariogram in an average sense, the coefficient of variation of the average semivariogram for the Fourier integral method is minimum. The realisations generated by the sequential Gaussian method have minimum mean simulation error. The choice of a simulation method based on variability reproduction and simulation errors remains difficult.

Jan 1, 1995

By Ormsby W, Peters M, Van Gils H, Kehprens P, De Boorder H

The northern margin of the Arunta Block is characterized by a metasedimentary and volcanic sequence of lower metamorphic grade than that of the central Arunta Block. Whereas the Harts Ranges have granulite to amphibolite metamor- phic grades, the northern margin only reached greenschist to lower amphibolite facies. Most of the high grade area of the central Arunta Block appears to be unprospective, but the lower grade marginal fringe contains most mineral pros- pects to name a few: Barrow Creek, Molyhill and the Jervois Mine. Numerous smaller prospects occur in this marginal zone. Four major lithostratigraphic units can be recognized in the Jervois Mine area: 1. Gneissic Suite consisting of granitic and rhyolitic gneisses which are characterized by a distinct intersection lineation. 2. Metasedimentary Suite of cordierite- biotite schists and chlorite-biotite schists. 3. Mine Sequence, consisting of spotted schists with andalusite and cordierite, quartz- sericite-feldspar schists with distinct rhyo- litic remnants and quartz-sericite-feldspar schists which contain the lode horizons:

Jan 1, 1984