Search Documents

By R Nicholson, N D. Cox, N W. A Lambert

"This paper reports on the long-term operation of a particle density meter (PDM) at the Bloomfield coal handling and preparation plant (CHPP). This unit has been operating continuously for over three years, providing real-time data to the operators to allow the monitoring of flotation circuit performance. PDM outputs include slurry density, solids concentration on both mass and volumetric basis, and particle density. Knowing the average particle density of a stream allows for the optimisation of the process in real-time.The calibration of the solids concentration measurement device proved very difficult as the factory calibration techniques and existing laboratory analysis did not give accurate or reliable results. The solids concentration device had to be re-engineered and a new calibration method developed that gave accurate and repeatable results. Independent verification of samples taken from the PDM was undertaken as part of the trial process.The operational reliability of the PDM was a major point of investigation. The initial installation of the unit revealed issues with large, misplaced material of up to 20 mm periodically entering the unit, leading to feed blockages. The presence of these misplaced, oversized particles in the flotation circuit was resolved by installing innovative automatic back flush systems on the PDM.From a plant perspective the PDM has been an invaluable instrument that has enabled irregularities in the flotation circuit performance to be identified, which sampling had not and could not readily identify. This was achieved by close monitoring of real-time tailings composition on a minute by minute basis over short and extended periods. Variations in the tailings stream with respect to particle density and solids concentration were traced back to other issues in the plant. In addition, the PDM has allowed cell optimisation with respect to reagent dose rate to be improved. The PDM with real-time feedback can negate the need for large sampling campaigns and analysis during plant optimisation programs.Citation:Lambert, N, Cox, N and Nicholson, R, 2016. Particle Density Meter, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 245–250 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M Revell, B Sainsbury, D Sainsbury

This paper extends the existing knowledge associated with the design and placement of prefabricated pastefill barricades through a consideration of asymmetric drive geometry and conditions. The load capacity of prefabricated barricades and their failure modes are considered in relation to abutment geology and barricade geometry that includes curvature and span and drive geometry that includes abutment angles, haunch angles and misalignment. Design charts are provided for typical barricade sizes to provide general guidance for design capacities and optimising location placement based on asymmetric drive geometry. A recent barricade failure is considered in relation to the drive geometry and the potential impact it had on the installed capacity.

Nov 29, 2022

The inauguration of a geological department for the mines of North Broken Hill Limited necessitated the provision of accurate plans and sections upon which geological facts and projections might be plotted.Unfortunately, the basic data were very inadequate. For the British Section, sill survey plans were available, but no regular stope plans. Filling surveys had been preserved for many stopes, but on innumerable pieces of tracing linen, without heights of any kind, and not altogether reliable (as indicated by the finding of very inconsistent duplicates). For the bulk of the old stopes no plans exist at all. The expenditure of much time and patience has resulted in the co-ordination of most of the existing stope data, but the British Section must for the rest of its life continue to have surprises in store, as has been the case for many years past. Manufacture and preservation of stope records has, of course, been on a sound footing during recent years. No reliable cross-sections of the British Section were available.The Marsh, Junction, and Junction North Sections have for the most part very poor data. In the North Section, level plans were fairly reliable, and cross sections of the lode made for ore reserve purposes have been preserved for quite a few years. No floor plans of stopes were kept, however, until a couple of years ago.Diamond Drill records vary in quality. Practically none exist for the Junction and Junction North Sections. Logs have been kept for the British Section drill holes, but are...

Jan 1, 1940

By H Lieberwirth, M Pfeifer, F Heinicke

HPGRs (high pressure grinding rolls) have been developed within the last decades for energy efficient processing of a wide variety of ores. Special interest has been raised by projects increasing the capacities of processing plants by installing HPGRs prior to ball mills. Bond ball mill tests have been used for decades as a base for ball mill dimensioning in mineral circuits. For final CAPEXOPEX considerations of the processing circuit, one key question is about the level of grinding energy split between HPGR and downstream grinding stages. This is especially interesting if the downstream process comprises multiple grinding stages combined with separation steps. The paper presents investigations on grinding energy consumption, size distribution and microfracturing of HPGR products, which affect the efficiency of the whole comminution and sorting process.

Aug 24, 2022

By E J. Hancock, K H. B Chu

Failures within hard rock underground excavations have historically been defined by a depth of failure, estimated in the field or through individual measurements, with a simplified failure geometry; such as 1/3 span, cubic or paraboloid. This simplified shape, volume and mass of failure is typically used to estimate in situ demand as a simplified discrete point. However, the highly variable failure geometry indicates simplified methods to estimate the mass can be erroneous in comparison to high precision LiDAR scans. Advances in technology have enabled the accurate capture of failure geometry and allow a far more accurate analysis of failures to be completed. This case study investigates a number of real-life failures to accurately define the failure geometry, the distribution of the failure parameters and compares this to traditional methodologies. This paper also outlines a suggested means of standardising failure geometry parameters whilst accounting for their variability.

Nov 29, 2022

As the title indicates the central themes discussed in this contribution are sustainable development, information systems, and extractive industry. More specifically, the objective is to present a prototype for the systematic generation of extractive industry (henceforth: EI) û specific sustainability information. The paper begins with the authorÆs viewpoints on the core notions of sustainability, and development, as well as their relationship to information. These set the stage for the introduction of the information system (IS), as well as the follow-up sustainability information system (SIS) extractive industry sustainability information system (EISIS) concepts and related discussions. The paper continues with a second part, in which, efforts to research and develop an EISIS prototype are described. First, the team is presented. Second, the systemÆs aim and target groups are briefly discussed. After, an articulated overarching EISIS conceptual model emphasising capital accumulation, and service flow concepts û is presented. This is followed by a detailed description of the assembled prototype with a focus on data and information generation. The formulation of data generation, storage and transmission processes, as well as its use in sustainability interpretation rules and their embedment in the conceptual model is made with respect to monetised stock and flow parameters, measured in the appropriate dimensions. In the third part, the author presents and discusses the results of a first round of prototype experimental development in three major EI firms. First, the system observation, and data analysis protocols are described. Second, a review of protocol implementation, and respective results, is made. Finally, the overall performance of the proposed prototype, and development process issues are discussed, before suggesting areas for improvement and future research. The paper ends with a conclusion in which the author provides a retrospective balance of the æknowledge creation projectÆ, as well as a prospective outlook for research in this field; before acknowledgements are made and references provided.

Jan 1, 2009

By T Belligoi

Diamond cores and drill chips provide the only direct physical evidence for ore containing rocks. Early characterisation of cores and drill chips is important as it provides critical information for downstream processing. Traditional characterisation techniques include visual logging by a geologist or analytic and spectroscopic methods but they are time consuming and can miss some important textural or geomechanical features.The goal of this work is to evaluate the application of image analysis to iron ore cores and drill chips and to suggest improvements to existing core-scanning and chip monitoring systems. Two samples of massive ore differing by their mineralogy and texture, as well as two different batches of drill chips, have been imaged and analysed. Results are compared in function of the imaging system and the classification algorithms.As a conclusion, despite the necessity for more testing and improvements in calibration and lighting, it is obvious that image analysis technologies can bring a lot of useful information in the perspective of a geometallurgical mapping of the deposit.

Jul 11, 2011

By G Morgan, C Kemp

In December 2010, a trial of borehole radar technology was conducted to test the usefulness of the technique in better refining the position and geometry of narrow vein orebodies away from the primary data sources of drilling and mapping of development excavations. This paper summarises the reasons why the technique was applied, describes the testing methods selected and summarises the outcomes of the trial.Poor reconciliations of recovered metal from a section of an orebody at Jundee mine site, Western Australia, led to an investigation that identified insufficient understanding of the geometry of a narrow vein orebody as a potential cause. This orebody was situated between mapped development excavations and away from surrounding drill holes. Borehole radar was identified as a possible technique that could supply information on vein location and continuity away from other data sources allowing more accurate orebody modelling and subsequent stope optimisation.A borehole radar instrument (10 - 100 MHz frequency) was inserted into pairs of purpose-drilled boreholes on either side of relatively well-constrained mineralisation and the radar reflection data was collected. This process was repeated in five locations across the mine to represent the most common geological settings, lithologies and orebody varieties encountered at Jundee to determine the suitability of applying the technique in each of these settings. Collected, processed and interpreted radar data was compared to other geology data collected independently for verification and interpretation.Conclusions drawn from the analysis were that the technique could effectively determine the following features of the mineralised veins in the majority of test environments: geometry of veins, magnitude of offsets where structures intersect and orientations of planar structures with short strike length. The technique was very useful in selecting the appropriate structural interpretation where available data could lead to multiple, equally likely, interpretations.CITATION:Kemp, C and Morgan, G, 2012. Using borehole radar to refine orebody interpretations in a narrow vein gold deposit, in Proceedings Narrow Vein Mining 2012 , pp 121-130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By C Jacobsen, N Harries

Assessing and managing instability hazards is an essential activity when working with unstable natural slopes and excavated open pit mining slopes. Slope monitoring has become the standard technique for the management of geotechnical risks associated with mine slope instability hazards. In recent decades, a proliferation of new monitoring techniques such as terrestrial radar, satellite InSAR and LIDAR have become standard operational tools, complementing conventional survey-based monitoring solutions. A reliable monitoring system should identify and record incipient anomalous slope movement. Although the most obvious purpose of a monitoring system is safety related, slope deformation and performance monitoring also enhance the understanding of slope behaviour and assists in improving system design and implementation. For a monitoring system to be considered an effective early warning tool, it needs to operate in real-time and should be linked to the mine’s emergency communication systems. Terrestrial radar systems have been developed that can provide near real-time measurements, at a high level of precision and covering broad areas in all weather conditions. This has had a positive impact on the management of geotechnical risks in operational conditions. The technology adoption of RADAR in mine monitoring has significantly progressed in the last 20 years from technology enthusiasts, to visionaries, to pragmatists to conservative users. However, the increasing adoption of RADAR cannot reduce or remove other monitoring techniques that often have important benefits; even if these technologies cannot be used as a real-time operational tool. An increasing awareness on the importance of combining data from different monitoring techniques to develop a holistic picture of all possible geotechnical hazards is a current industry trend. This is proving to be an excellent foundation for managing hazards associated with slope instability in open pit mines, and is only expected to improve with time with the adoption of new technologies based on big data and Artificial Intelligence (AI).

Nov 29, 2022

Sampling errors result from heterogeneities within the lot under study. Within a rock mass in situ heterogeneity results in the geological nugget effect, which accounts for most of the natural variability. In broken rock, constitution and distribution heterogeneities are important. A major result of the constitution heterogeneity is the Fundamental Sampling Error (FSE) which is the smallest residual error that can be achieved. It cannot be eliminated, but can be minimised and refl ects the fact that the broken rock sampling process is never completely free of error. Together with other sampling errors, FSE contributes to the total nugget effect. The FSE for a sampling protocol can be evaluated using the so-called Gy equation. Its practical applications to low-grade gold ores have often been unsuccessful due to problems linking the FSE and minimum sampling mass and the defi nition of key parameters such as the liberation diameter. Well-designed sample protocols minimise the total sampling error and hence the nugget effect. Reduction of the nugget effect is a key requirement for all sampling programs whether related to exploration and resource evaluation, metallurgical test sampling, grade control or metallurgical plant sampling. This contribution reviews the relationship between heterogeneity, FSE and nugget effect in gold deposits; and emphasises the need for FSE management throughout the mine value chain.

Aug 1, 2010

Diamonds have been known in Australia for many years, especially in association with alluvial gold and tin occurrences. Exploration for primary sources in the Kimberely area of Western Australia has been carried out since 1968, culminating in the discovery, in 1979, of the Argyle Kimberlite No 1 (AK1) kimberlite pipe. Various techniques have been used in the search for diamonds such as geologic interpretation, aerial photography and Landsat, soil geochenical techniques, geophysics, and stream sediment sampling. Stream sediment sampling, a method developed in South Africa, using the detection of indicator minerals derived from kimberlites in gravel samples, has had wide application and success in Australia. Nevertheless, although Australian diamond bearing kimberlite and lamproite rocks contain some of the classic indicator minerals, their concentrations are generally much lower than in South Africa and Russia. Despite this paucity of indicators, stream sediment sampling is still the best known and most commonly used method of diamond prospecting in Australia. Small samples are treated by hand but larger samples require the use of diamond pans, jigs or heavy media separation plants. Each of these methods has advantages and disadvantages. The final concentrate is passed over a grease table or subjected to x-ray sorting.

Jan 1, 1984

The Mineral Research Centre is located at Perth in the suburb of Waterford, adjacent to Curtin University of Technology and within a Technology Precinct which includes Technology Park. The Centre, constructed by the WA Government at a cost of $16 million and occupied in late-1994, comprises three separate buildings housing the CSIRO Division of Minerals, Curtin University's School of Chemical Engineering and the Mineral Processing Laboratory of the Department of Minerals and Energy. The emphasis on R&D at the Centre is primarily in hydrometallurgy as a result of staff expertise, extensive bench and pilot-scale facilities, track record with the industry and, very importantly, two of the occupiers being partners in the AJ Parker Cooperative Research Centre for Hydrometallurgy. Staff in the Centre have a long involvement with R&D agencies such as AMIRA and MERIWA. The hydrometallurgical focus of the Centre complements that of pyrometallurgy at the GK Williams CRC in Melbourne and the Centre for Mining Technology and Equipment in Brisbane, to ensure that the mineral processing industry in Australia has access to a complete range of expertise and facilities to serve its needs.

Jan 1, 1996

By D Bruggemann, F Sereshki

There has been an ongoing research on coal and gas outburst for the past two decades at the School of Civil, Mining and Environmental Engineering, University of Wollongong. Research study began with a humble beginning, initially conducting basic laboratory studies on the coal and gas properties, progressing into the determination of gas content of coal by sorption technique and the effect of gas pressures on coal strength. The present laboratory facilities and research interests are extended to include the study of coal permeability and shrinkage properties and their effect of gas drainage characteristics with respect to gas type, and pressures. All the changes are examined with respect to changing in-site geological conditions of the coal deposit investigated. The aim is to provide a long-term support to industry in establishing a data bank for Australian coal deposit characteristics and properties.

Jan 1, 2005

By J L. Stacey

The diverse priorities, drivers and concerns of multiple stakeholders in the minerals industry complicate the integration of sustainable development considerations into mine design, as well as operational and strategic decisions. The ability of the industry to address all role-playersÆ needs, or indeed, to achieve consensus among all role players on the plethora of sustainable development issues seems a noble yet unattainable goal. One of the difficulties in assessing the relative importance of sustainable development issues across many stakeholders is the inevitable lack of impartiality in valuing these issues. Starting from a premise that transparency and fairness of the process are absolute prerequisites for progress, but that consensus is not, an approach has been developed in which all stakeholders are asked to assess the importance of all other stakeholdersÆ priorities, excluding their own. The approach recognises that stakeholders have different levels of contribution, understanding, vested interests, and perceptions of legitimacy and entitlement, across the diversity of sustainable development issues and decision criteria. Using Triangular Value Analysis, the relative weightings of each of the stakeholderÆs priorities are determined through a regression-like technique. The uniqueness of this approach is the manner in which self-assessment bias and overemphasis of stakeholdersÆ own priorities are avoided. The methodology can be used for both internal and external stakeholders, and in conjunction with other group decision making techniques, such as the nominal group or Delphi techniques. This paper will illustrate how Triangular Value Analysis may be applied in the minerals industry to determine priorities in various decisions relating to potentially conflicting sustainable development priorities within the industry.

Jan 1, 2009

By D T. Ribeiro, J F. C L Costa, J C. Koppe

Drilling and sampling are responsible for most of the costs during mineral exploration, especially in multi-elements and polymetallic deposits, such as iron, manganese and bauxite deposits. On these deposits, often it is necessary to estimate multiple attributes at several granulometric fractions, ie distinct particle sizes. This paper investigates the effect of sampling at a close spacing grid only the head grades for the multiple chemical species in iron ore deposits. The remaining required data at the various grain sizes are sampled at a sparse grid. The derived geological model is checked for precision and accuracy comparing the output obtained against a model obtained using a complete isotopic data set including head grades and chemical analysis at each granulometric fraction analysed at all sampled positions. Among the several tested alternatives, the best procedure for dealing with the posed problem involved utilising the correlation coefficients between the grades at distinct fractions to obtain an isotopic database prior to interpolation. Cokriging was the method used, based on the intrinsic coregionalisation model. Estimates were obtained with the quality needed for the proposal of the study. Results showed that at least 50 per cent of the blocks were estimated with errors less than ten per cent relative to the grades obtained at the reference model, using only 15 per cent of the granulochemical data employed to obtain the reference model. The methodology also preserved the correlations between the attributes in their several granulometric fractions on the estimated model.

Sep 26, 2011

By B Roache

Ground support installation into the face of development headings has become an accepted practice at many Australian hard rock mines. Ground support is installed in the development face to reduce personnel exposure to rockfall while conducting work tasks such as marking up, installing lifter tubes, charging, and face sampling. The ground support system installed in the face is typically friction bolts and mesh. This support system can be effective at reducing rockfall occurrence, but it also increases the cost of development per metre, in terms of capital for the ground support, jumbo and operator capital allocation and the installation time slowing each drill and blast cycle. Other issues associated with meshing and bolting the development face include management of rock bolts and mesh sheets in the fired dirt of every cut, damage to services such as vent duct, geometry issues when installing ground support onto irregular development profiles and operator error. Fibrecrete installation onto the development face for support is an option considered by many mines, but it can be difficult to manage due to the removal of visual indications of misfires and slowing the mining cycle due to the wait time for fibrecrete curing. The use of Thin Spray Liner (TSL) products in underground hard rock mines has been relatively infrequent in the past, mainly due to issues with cost, health and safety, and liner strength. Kanmantoo Mine investigated the use of TSLs for the purpose of development face support, while collecting data on the costs and practicalities associated with their use. Several TSL products were trialled and a preferred TSL product was selected for use as face support. Cost savings, drill and blast cycle timing improvements and other benefits were achieved while meeting the requirement to reduce rockfall risk.

Mar 29, 2023

By James JV, Petho SZ

The South Deep surface shaft system is being sunk to a final depth of 2750 in below surface and on completion will be the deepest single drop haft in the world. The shafts will intersect the target reef horizon at 2650 to below surface. In order to negate the requirement for a shaft pillar, which would he extremely large at this depth, the reef horizon in the vicinity of the intersection is currently being mined. A high quality crushed waste/classified tailings backfill is being placed in the longwall stoping panels around the shaft intersection area. This kill limit closure and ride which following shaft reef intersection could have a detrimental effect on the long term shaft stability. This paper discusses underground instrumentation results and numerical modelling exercises carried out to confirm that the shaft system will he stable throughout the life of the mine. Instrumentation projects include closure and ride measured between backfill paddocks and haulage leveling exercises carried out to determine the far field rockmass response to mining with stiff backfill.

Jan 1, 1998

By C Armstrong, B Wentzinger

Upstream embankment raises often represent the lowest cost option for increasing the capacity of tailings storage facilities (TSF), but also pose the highest stability risk due to constructing on top of previously deposited tailings.This paper presents an overview of key aspects in the geotechnical investigation and design of upstream raises and some recent lessons learnt from experience across a number of TSFs in Australia. A summary of recommended field investigation and laboratory testing methods is provided with a focus on collecting quality information for design purposes. A strong focus is given in developing an accurate assessment of pore water pressures, which, if not correctly understood can have disastrous consequences on tailings strength parameter interpretation and wall stability assessment in static and post-seismic conditions.The assessment of the contractive or dilative shearing behaviour of the tailings material and rigorous interpretation of design characteristic values are presented. Some comments on stability analysis options and proposed methodology are also provided.CITATION:Wentzinger, B and Armstrong, C, 2018. Lessons learnt in geotechnical investigation and stability analysis for upstream tailings storage facility raise design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 333–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Vann, S Dunham, M Job

Two-dimensional (2D) estimation approaches have significant advantages over three-dimensional (3D) approaches when dealing with a narrow vein- or layer-like geometry. The main motivation for 2D estimation is that bias due to non-additivity of grade is avoided. The various aspects of 2D estimation are illustrated by use of a case study from the 1A Shoot Nickel deposit at Leinster, Western Australia. The width of the 1A mineralisation is variable, and so are the angles of drilling intersection. Consequently, the variable of interest (in this case nickel grade) is not suitable for direct kriging because it is defined on non-uniform support. However, grade can also be defined as the ratio of two variables that are suitable for direct kriging: thickness and accumulation. In the 2D approach, tonnage equates to thickness and metal equates to the product of grade and thickness, also called æaccumulationÆ. In the simplest approach we can independently krige accumulation and thickness and derive the grade by the ratio of the two resultant estimates. The thickness and accumulation variables must be in a consistent projection orientation, for example a horizontal projection in the case of steeply inclined mineralisation like 1A. Because the density is not constant across the 1A (and most other) deposits, the issue of density weighting is also discussed. The impact of the correlation between grade and length, or grade and density are important issues in implementation of 2D estimation. The circumstances under which these correlations need to be taken into account (by co-kriging) are reviewed. Finally some comments are made on the final use of the resultant 2D estimate for mine planning purposes.

Jan 1, 2003

By M McCurd, M Lynch, B H. Yin, S Mendoza, C W. Bumby, Y Iwasaki, B Rumsey

Iron and steel production is responsible for approximately 6.3 per cent of global anthropogenic CO2 emissions. Direct reduction of iron with hydrogen is a potential route for decarbonising the iron and steel industry. Extensive small-scale laboratory experiments have been performed to test the feasibility of hydrogen-direct reduction of iron ores sourced from diverse geographical locations. However, test results from the batch reduction of small-sample do not necessarily translate to continuous commercial-scale processes. Establishing a small-scale continuous test reactor for H2- DRI process is challenging, requiring substantial resources and investment. The limited availability of small-scale reactors that enable testing under relevant conditions has become a major obstacle for H2-DRI development, leaving a big gap between laboratory success and proof of commercial feasibility. Here, we report on the recent commissioning of a continuous counter-flow vertical shaft reactor, which has a processing capacity of 6 kg/hr iron ore pellets at up to 100 NL/min H2 flow. We believe this to currently be the largest H2-DRI facility in the Southern Hemisphere. In this talk, we will discuss the design and construction journey for this reactor, starting from the initial system design to the initial demonstration of H2 reduction of titanomagnetite ironsand pellets. This reactor now enables a range of research capacities, including the validation of laboratory results on a larger scale with practical operational variables, feasibility assessment of hydrogen direct reduction of different iron ores on a commercial scale; identification of scalability, sticking, and other potential issues before building a full-scale plant; and a viable solution for producing small-quantity DRIs for downstream melting investigations. Overall, this new research facility offers significant benefits for assisting the transformation of iron and steel production to a more sustainable and green industry.

Sep 18, 2023